TY - JOUR A1 - Gašo, Peter A1 - Pudiš, Dušan A1 - Seyringer, Dana A1 - Kuzma, Anton A1 - Gajdošová, Lenka A1 - Mizera, Tomáš A1 - Goraus, Matej T1 - 3D polymer based 1x4 beam splitter JF - Journal of Lightwave Technology N2 - We present a new concept of 3D polymer-based 1 × 4 beam splitter for wavelength splitting around 1550 nm. The beam splitter consists of IP-Dip polymer as a core and polydimethylsiloxane (PDMS) Sylgard 184 as a cladding. The splitter was designed and simulated with two different photonics tools and the results show high splitting ratio for single-mode and multi-mode operation with low losses. Based on the simulations, a 3D beam splitter was designed and realized using direct laser writing (DLW) process with adaptation to coupling to standard single-mode fiber. With respect to the technological limits, the multi-mode splitter having core of (4 × 4) μm 2 was designed and fabricated together with supporting stable mechanical construction. Splitting properties were investigated by intensity monitoring of splitter outputs using optical microscopy and near-field scanning optical microscopy. In the development phase, the optical performance of fabricated beam splitter was examined by splitting of short visible wavelengths using red light emitting diode. Finally, the splitting of 1550 nm laser light was studied in detail by near-field measurements and compared with the simulated results. The nearly single-mode operation was observed and the shape of propagating mode and mode field diameter was well recognized. KW - Optical splitter KW - 3D splitter KW - Polymer KW - Y-branch splitter Y1 - 2021 U6 - http://dx.doi.org/10.1109/JLT.2020.3026170 SN - 0733-8724 SN - 1558-2213 VL - 39. Jg. IS - H. 1 SP - 154 EP - 161 ER - TY - BOOK ED - Haber, Peter ED - Lampoltshammer, Thomas J. ED - Mayr, Manfred ED - Plankensteiner, Kathrin T1 - Data science – analytics and applications BT - proceedings of the 3rd International Data Science Conference – iDSC2020 KW - Data science KW - Machine learning KW - Articifial intelligence KW - Data analytics Y1 - 2021 SN - 978-3-658-32181-9 SN - 978-3-658-32182-6 U6 - http://dx.doi.org/10.1007/978-3-658-32182-6 N1 - Die iDSC’20 wurde gemeinsam mit der FH Salzburg organisiert und von der FH Vorarlberg als Online-Konferenz veranstaltet. PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Rosmann, Sabrina A1 - Feilhauer, Thomas A1 - Finck, Steffen A1 - Sobotka, Martin ED - Haber, Peter ED - Lampoltshammer, Thomas J. ED - Mayr, Manfred ED - Plankensteiner, Kathrin T1 - An easy-to-use execution environment for the parallelisation of computationally intensive data science applications T2 - Data science – analytics and applications. Proceedings of the 3rd International Data Science Conference – iDSC2020 N2 - With Cloud Computing and multi-core CPUs parallel computing resources are becoming more and more affordable and commonly available. Parallel programming should as well be easily accessible for everyone. Unfortunately, existing frameworks and systems are powerful but often very complex to use for anyone who lacks the knowledge about underlying concepts. This paper introduces a software framework and execution environment whose objective is to provide a system which should be easily usable for everyone who could benefit from parallel computing. Some real-world examples are presented with an explanation of all the steps that are necessary for computing in a parallel and distributed manner. KW - Parallel computing KW - Distributed computing KW - Software framework KW - Execution environment KW - Stress testing Y1 - 2021 SN - 978-3-658-32181-9 SN - 978-3-658-32182-6 U6 - http://dx.doi.org/10.1007/978-3-658-32182-6_4 N1 - Verlagshinweis zum Abstract: Die NutzerInnen dürfen die Inhalte nur zum Zwecke der wissenschaftlichen Forschung ansehen, drucken, kopieren, herunterladen sowie für Text- und Datamining verwerten. Die Inhalte dürfen weder ganz noch teilweise wörtlich (wieder)veröffentlicht oder für kommerzielle Zwecke verwendet werden. Die NutzerInnen müssen sicherstellen, dass die Urheberpersönlichkeitsrechte des/der AutorIn sowie gegebenenfalls bestehende Rechte Dritter an den Inhalten oder Teilen der Inhalte nicht verletzt werden. SP - 16 EP - 23 PB - Springer Vieweg CY - Wiesbaden ER - TY - JOUR A1 - Chovan, Jozef A1 - Tomaska, Martin A1 - Uherek, Frantisek A1 - Hasko, Daniel A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Koza, Eduard A1 - Pavlov, Jozef T1 - Demonstration of automated adjustment and coupling of fiber array to PICs based on the detection of edges JF - Fiber and Integrated Optics KW - Automated Adjustment KW - Coupling of Fiber Array KW - PICs Y1 - 2020 U6 - http://dx.doi.org/10.1080/01468030.2020.1717018 VL - 39. Jg. IS - H. 1 SP - 24 EP - 38 ER - TY - CHAP A1 - Haag, Hermann A1 - Mitterbacher, Andre A1 - Hämmerle, Florian T1 - Losses in Ferroelectric Dielectric Ceramic Capacitors due to Electromechanical Resonances T2 - PCIM Europe digital days 2020. 7 – 8 July 2020. International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management KW - Ferroelectric losses KW - Ceramic capacitor KW - switched mode power supply Y1 - 2020 SN - 978-3-8007-5245-4 SP - 456 EP - 460 PB - VDE VERLAG GMBH CY - Berlin u.a. ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdošova, Lenka A1 - Gašo, Peter A1 - Jandura, Daniel A1 - Pudiš, Dušan ED - Jaehwan, Kim T1 - Experimental verification of 3D polymer based 1x4 Y-branch splitter T2 - Nano-, Bio-, Info-Tech Sensors, and 3D Systems IV. 27 April–8 May 2020. Online Only, United States KW - Y-branch splitter KW - IP-Dip polymer KW - direct laser writing lithography Y1 - 2020 SN - 9781510635333 U6 - http://dx.doi.org/10.1117/12.2555782 PB - SPIE CY - Bellingham, Washington ER - TY - THES A1 - Rauch, Monika T1 - Erfolgsfaktor agile Ansätze im Kompetenzerwerb BT - Erhebung der Potenziale agiler Ansätze zum Kompetenzerwerb in Vorarlberger Unternehmen N2 - Flexibilität, Anpassungsfähigkeit und eine schnelle Reaktionsfähigkeit ist der Anspruch an die Arbeitswelt von heute und wird in Zukunft weiter an Dynamik gewinnen. Durch die Entwicklung agiler Ansätze wurden hierfür Lösungsansätze gefunden. Diese können an die Anforderungen der eigenen Arbeitsumgebung adaptiert werden und unterstützen die Unternehmen dabei, auch bei zukünftigen Veränderungen der Arbeitswelt erfolgreich agieren können. Für eine effektive Nutzung agiler Ansätze ist eine stetige Weiterentwicklung der Kompetenzen der Mitarbeitenden unumgänglich. Klassische Methoden zum Erwerb neuer Kompetenzen hinken dem Wandel hinterher. Der Einsatz agiler Ansätze im Arbeitsalltag erfordert daher agile Kompetenzentwicklungsansätze. Ob agile Ansätze selbst ein Erfolgsfaktor beim Erwerb von Kompetenzen darstellen, wird in dieser Studie behandelt. N2 - Flexibility, adaptability, and the ability to react quickly are the demands on the today’s working world and will continue to gain momentum in the future. The development of agile approaches enabled to find solutions to these challenges. These can be adapted to the requirements of one's own working environment and support the companies acting successfully in future changes of the working world. For an effective use of agile approaches, a continuous development of the competencies of the employees is indispensable. Traditional methods for acquiring new competencies lag behind their changing environment. The use of agile approaches in everyday working life therefore requires agile competence development approaches. Whether agile approaches themselves represent a success factor in the acquisition of competencies is the subject of this study. T2 - Success factor agile approaches in competence acquisition KW - Agilität KW - Kompetenzerwerb KW - Erfolgsfaktor KW - Kompetenzen Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3665 ER - TY - THES A1 - Wille, Ramona T1 - Potenziale und Herausforderungen von People Analytics BT - Einsatzmöglichkeiten für Industrieunternehmen in der DACH-Region N2 - Erfolgreiche Personalarbeit zeichnet sich durch gute, datenbasierte Kenntnisse und Verknüpfungen über alle Geschäftsbereiche, mit Fokus auf die Menschen im Unternehmen, aus. In vielen Unternehmen werden relevante Personalentscheidungen noch immer aus dem Bauch heraus getroffen, anstatt durch eine fundierte Grundlage von Daten. People Analytics ist einer der wichtigsten Trends im Personalmanagement und dennoch wird es kaum in einer Personalabteilung der DACH-Region eingesetzt. Ziel dieser Masterarbeit ist es, die Chancen und Herausforderungen von People Analytics auszuarbeiten und Einsatzmöglichkeiten für Industrieunternehmen der DACH-Region aufzuzeigen. Dafür werden die theoretischen Grundlagen und Anwendungsprozesse von People Analytics dargelegt und die Herausforderungen und Hindernisse sowie die Möglichkeiten und Chancen ausgearbeitet. Im Rahmen von zwei Experteninterviews mit HR-Spezialisten werden die aktuellen Gegebenheiten der DACH-Region eruiert. Dabei wurde ersichtlich, dass die größten Chancen von People Analytics sowohl in der Literatur als auch den befragten Personen zufolge, in der datenbasierten Entscheidungsfindung, der strategischen Personalentwicklung sowie in der strategischen Personalplanung liegen. Die größten Herausforderungen werden in der Akzeptanz der Mitarbeitenden, der IT-Infrastruktur sowie in der fehlenden analytischen Kompetenz der Mitarbeitenden im Personalbereich gesehen. Einsatzmöglichkeiten, abseits der derzeit bereits ausgewerteten Unternehmenskennzahlen, sind aufgrund der oben genannten Herausforderungen sowie den marginal vorhandenen Daten in den Unternehmen der DACH-Region derzeit keine gegeben. N2 - Successful Human Resource management is characterized by relevant data-based expertise, linked across all business areas with a focus on the people in the company. In many companies, relevant personnel decisions are still made on the basis of gut feeling rather than on a solid foundation of data. People Analytics is one of the most important trends in Human Resource management and yet it is hardly ever used in a Human Resource department of the DACH-region. The purpose of this master's thesis is to elaborate the opportunities and challenges of People Analytics and to show application possibilities for industrial companies of the DACH region. The theoretical foundations and application processes of people analytics are demonstrated and the challenges and obstacles as well as the possibilities and opportunities are elaborated. In the course of expert interviews with two HR experts, the current conditions of the DACH region will be determined. It turned out that the greatest opportunities for people analytics, according to both, literature and surveyed people, are data-based decision-making, strategic personnel development and strategic personnel planning. The biggest challenges are considered to be the acceptance of the employees, the necessity of specific IT-infrastructure and the lack of analytical competence of the employees in the Human Resources department. Due to the challenges mentioned above and the marginal availability of data in the companies in the DACH-region, there are currently no potential applications apart from the key company figures already evaluated. T2 - Potentials and challenges of People Analytics : application possibilities for industrial companies in the DACH-region KW - People Analytics Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3662 ER - TY - THES A1 - Kaufmann-Pauger, Angelika T1 - Führung im Zeitalter der digitalen Transformation BT - Leadership-Kompetenzen als kritischer Erfolgsfaktor N2 - Die digitale Transformation stellt Führungskräfte vor neue Aufgaben. Sie sind aufgefordert, einen Lernweg zu beschreiten und nehmen dabei eine Vorbildfunktion ein. Diese Masterarbeit widmet sich der Fragestellung, welche Kompetenzen Führungskräfte im Zeitalter der digitalen Transformation benötigen und welche Auswirkungen das auf Leadership-Entwicklungsprogramme hat. Nach der theoretischen Bearbeitung der Thematik wurden qualitative Interviews mit Expertinnen und Experten im Bereich Leadership durchgeführt. Es folgte eine Online-Befragung von Führungskräften, die quantitativ ausgewertet wurde. Die Ergebnisse zeigen, dass analoge Kompetenzen im digitalen Zeitalter weiterhin die Hauptrolle in der Führungsarbeit spielen. Eine starke Ausprägung der digitalen Kenntnisse führt jedoch zu einer höheren Profitabilität. Die Untersuchung zeigte bei den Befragten Unterschiede bei den Herausforderungen, Kompetenzen und Weiterbildungswünschen in Bezug auf Geschlecht, Alter, digitale Reife und Größe der geführten Teams. Daraus folgt, dass Programme in der Führungskräfteentwicklung individuelle Anpassungen erfordern. Diese Masterarbeit richtet sich an Interessierte, die das Spannungsfeld von Führenden in der digitalen Transformation verstehen wollen. N2 - The digital transformation challenges leaders with new tasks. They are requested to learn continually, and at the same time they act as role models. This master thesis tackles the question which competences leaders need to be successful in the era of digital transformation. Thus, the first part takes a close look at the theory. Besides, this work includes qualitative interviews with experts in the field of leadership as well as an online survey with leaders which has been evaluated in a quantitative way. The findings show that analog skills still play a major role for leaders in the digital era of transformation. However, digital knowledge leads to more profitability. Besides, the results show differences between the interviewees regarding the challenges, competences or desired leader development training in relation to gender, age, digital maturity and size of the guided team. Thus, programs for leadership development should consider an individual approach. This thesis is addressed to all persons who are interested in understanding the area of tension in which executive managers find themselves in the age of digital transformation. T2 - Leadership in the age of digital transformation KW - Führung KW - Kompetenz KW - Digitale Transformation KW - Leadership KW - Führungskraft Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3678 ER - TY - THES A1 - Gasser, Melanie T1 - Planspiel als Methode zur Entwicklung von Change-Management Kompetenzen in Organisationen T1 - Simulation game as a method for developing change management competencies in organizations N2 - Die Kompetenzentwicklung im Umgang mit Veränderungsprozessen für Mitarbeitende aller Hierarchieebenen ist essentiell, da diese zu einem festen Bestandteil des Alltags zählen. Durch speziell erstellte Planspiele für diesen Themenbereich werden Führungskräfte und Mitarbeitende für den Veränderungsprozess sensibilisiert. „SysTeamsChange“ stellt eines der marktführenden Planspiele in diesem Themenbereich dar. In diesem Tool werden die Teilnehmenden in die Lage versetzt, mit diversen Situationen richtig umzugehen. Die vorliegende Masterarbeit erörtert die Bedingungen, unter welchen das Planspiel „SysTeamsChange“ effektiv in Veränderungsprozessen eingesetzt werden kann. Zudem wird analysiert, ob es sich bei diesem Spiel um eine wirkungsvolle Methode für die Kompetenzentwicklung für Führungskräfte handelt und in welchen anderen Einsatzbereichen das Tool erfolgreich verwendet werden kann. Basierend auf den Ergebnissen der theoretischen Ausarbeitungen und durchgeführten Experteninterviews werden Handlungsempfehlungen zum verbesserten Einsatz von „SysTeamsChange“ abgeleitet. Dadurch soll den Unternehmen eine leichtere und effizientere Handhabung mit dem Einsatz dieses Tools ermöglicht werden. N2 - Competence development in dealing with change processes is essential for employees at all hierarchical levels, as these are an integral part of everyday life. Management and employees are sensitized to the change process through specially designed business games for this topic. "SysTeamsChange" is one of the market-leading simulation games in this subject area. In this tool, participants are put in a position to deal with various situations correctly. This master thesis discusses the conditions under which the simulation game "SysTeamsChange" can be used effectively in change processes. In addition, it analyses whether this game is an effective method for developing skills for managers and in what other areas the tool can be successfully used. Based on the results of the theoretical elaboration and conducted expert interviews, recommendations for actions for an improved use of "SysTeamsChange" are derived. This should enable companies to use this tool more easily and efficiently. KW - Planspiel KW - Change management Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3684 ER - TY - THES A1 - Krug, Adelheid T1 - Alter und Recruiting BT - die Bedeutung des Alters von Arbeitssuchenden bei der Personalgewinnung in Vorarlberg N2 - Die vorliegende Arbeit beschäftigt sich mit der Problematik von Arbeitssuchenden 45 plus in Vorarlberg. Zum Verständnis werden die Fachbegriffe Diversity, Generationen und Altersklassen, Altersdiskriminierung und Work Ability Index erläutert. Die Umfeld- und Einflussfaktoren beschäftigen sich mit den demografischen Grundlagen, den Potenzialen älterer Arbeitnehmender, dem alter(n)s-gerechten Arbeiten, möglicher Herausforderungen im Recruiting und Ideen anderer Länder. Im Abschnitt Methodologie und Methodik werden Grundlagen der qualitativen Forschung behandelt. Die Datenerhebung erfolgte durch Experteninterviews. Die Details dazu finden sich in den Passagen Sampling, Auswahl der Interviewpartner, Interview-Leitfaden, Auswertungsmethode und Gütekriterien. Die Arbeit fokussiert sich auf Industrieunternehmen in Vorarlberg sowie das AMS, die AK und die Caritas. Die Antworten aus den Leitfaden-Interviews führen schlussendlich zu potenziellen Reformansätzen, um die Situation für Arbeitnehmende 45 plus zu verbessern. Es ergeben sich mehrere Aspekte, welche wider das Einstellen von älteren Bewerbenden vorliegen. N2 - This paper concerns the issues and problems of jobseekers 45 plus in Vorarlberg. For a better understanding, the technical terms diversity, generations and age groups, age discrimination and Work Ability Index are explained. The environment and influencing factors deal with the demographic basis, the potential of older employees, age-appropriate work, possible challenges in recruiting and ideas from other countries. The section Methodology and Method handles the basics of qualitative research. The data collection is based on interviews with experts. The details can be found in the sections sampling, selection of interview partners, interview guidelines, evaluation method and quality criteria. The work focuses on industrial companies in Vorarlberg, as well as the AMS, AK and Caritas. The answers from the expert interviews ultimately lead to potential reform approaches in order to improve the situation for employees in the age of 45 plus. There are several aspects opposing the hiring of older applicants. T2 - Age and recruiting : the importance of age of jobseekers during the personnel search in Vorarlberg KW - Diversity KW - Altersdiskriminierung KW - Alter(n)s-gerechtes Arbeiten KW - Work ability index KW - Recruiting Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3685 ER - TY - THES A1 - Hankofer, Lana Bess T1 - Betriebliche Inklusion BT - die Handhabung betrieblicher Inklusion in Vorarlberger Industrieunternehmen und dem öffentlichen Sektor N2 - Rund 15% der österreichischen Bevölkerung haben eine dauerhafte Behinderung. In Vorarlberg allein leben ca. 5.000 Personen, welche nach dem Behinderteneinstellungsgesetz dem Kreis der begünstigt Behinderten angehörig sind, aber nur 51% dieser sind auch erwerbstätig, so der Stand 2018. Gleichzeitig gab es im Jahr 2018 in Vorarlberg 3.773 zu besetzende Pflichtstellen für begünstigt Behinderte Arbeitnehmende. Tatsächlich besetzt waren von diesen aber nur 52,64%. Es stellt sich somit die Frage, warum fast die Hälfte der zu besetzenden Pflichtstellen nicht besetzt ist, zumal das „Recht auf Arbeit“ als Menschenrecht in der UN-Menschenrechtskonvention verankert ist. Denn die Teilhabe am gesellschaftlichen und beruflichen Leben ist ein wichtiger Punkt für das Selbstwertgefühl eines jeden Menschen. Ziel dieser Masterarbeit ist daher aufzudecken, wie die betriebliche Inklusion in mittelständischen und großen Industrieunternehmen, sowie dem öffentlichen Sektor in Vorarlberg gehandhabt wird und welche Einflussfaktoren auf die Handhabung einwirken. Näher betrachtet werden diesbezüglich die Unterschiede in der Handhabung zwischen den privaten und den öffentlichen Einrichtungen sowie die internen und externen Faktoren, welche die Handhabung beeinflussen. Darüber hinaus soll in Erfahrung gebracht werden, welche Maßnahmen die Vorarlberger Unternehmen bereits ergreifen und wo Verbesserungsbedarf besteht. Um die Forschungsfrage zu beantworten wird im Anschluss an die Literaturrecherche ein Methodenmix aus qualitativen Experteninterviews und einer quantitativen Onlineumfrage eingesetzt. Die Ergebnisse aus den zwei Untersuchungen werden im weiteren Verlauf ausgewertet, kritisch reflektiert und in einem Fazit zusammengefasst. Betrachtet man die Forschungsfrage und die Ergebnisse der Untersuchung, so lässt sich zusammenfassen, das Vorarlberg bereits auf einem guten Stand der betrieblichen Inklusion ist. Die Entwicklung der letzten Jahre zeigt einen Paradigmenwandel, durch welchen sich das Bild vom „Armen Behinderten“ hin zur Selbstbestimmung und Chancengleichheit wandelt. Dieser ist noch nicht vollständig abgeschlossen, weswegen weiter in die Sensibilisierung und Aufklärung der Gesellschaft investiert werden muss, um Vorurteile und Unsicherheiten in Bezug auf Rechte und Pflichten abzubauen. Als externe Faktoren werden der rechtliche Rahmen, die Digitalisierung, sowie die Sichtbarkeit betrieblicher Inklusion und der Diversität von Behinderungen in der Gesellschaft genannt. Einfluss auf die Handhabung hat zudem die Vielfalt an Arten von Beeinträchtigungen, da die zu ergreifenden Maßnahmen auf diese abgestimmt werden müssen. Interne Faktoren stellen die Barrierefreiheit, sowie die persönlichen Haltungen und die Beweggründe der Unternehmer und ihren Mitarbeitenden dar. Abschließend lässt sich feststellen, dass betriebliche Inklusion dann gelingen kann, wenn jede Person unabhängig davon, ob sie eine Beeinträchtigung hat, oder nicht, als Individuum mit individuellen Stärken, Schwächen, Charakterzügen und Eigenschaften verstanden wird. Aufbauend auf diesem Menschenbild gilt es für jede Person auf Grund ihrer individuellen Eigenschaften die passende berufliche Tätigkeit zu finden. N2 - Around 15% of the Austrian population have a permanent disability. In Vorarlberg alone, there are approx. 5,000 people who belong to the group of favored disabled people according to the Disability Employment Act, but only 51% of these are also gainfully employed, according to the status in 2018. At the same time, there were 3,773 people to be occupied in mandatory positions for favored disabled workers. In fact, only 52.64% of them were occupied. This raises the question of why almost half of the mandatory positions to be filled are not filled, especially since the “right to work” is anchored as a human right in the UN Convention on Human Rights. The participation in social and professional life is an important point for everyone's self-esteem. The aim of this master's thesis is therefore to uncover how company inclusion is handled in medium-sized and large industrial companies, as well as the public sector in Vorarlberg, and which factors influence the handling. In this regard, the differences in handling between private and public institutions as well as the internal and external factors that influence handling are closely examined. In addition, the aim is to find out which measures Vorarlberg companies are already taking and where there is room for improvement. To answer the research question, a mix of methods consisting of qualitative expert interviews and a quantitative online survey is used after the literature search. The results of the two investigations will be evaluated, critically reflected and summarized in a conclusion. Looking at the research question and the results of the investigation, it can be summarized that Vorarlberg is already at a very good level of company inclusion. The development of recent years shows a paradigm shift through which the image of the “poor handicapped” is changing towards self-determination and equal opportunities. This has not yet been fully completed, which is why further investments must be made in raising awareness and educating society to reduce prejudices and uncertainties regarding the legal framework. The legal framework, digitization, and the visibility of operational inclusion in society are external factors. Internal factors represent the accessibility, as well as the personal attitudes and motivations of the entrepreneurs and their employees. In conclusion, it can be said that company inclusion can succeed if everyone, regardless of whether they have a disability or not, is understood as an individuum with individual strengths, weaknesses, traits and characteristics. Building on this image of man, it is important to find the right job for every person based on their individual characteristics. T2 - Company inclusion : the handling of company inclusion of people with disabilities in industrial companies and the public sector within Vorarlberg KW - Inklusion Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3669 ER - TY - THES A1 - Abl, Amina T1 - Die Wirkung von Lernmaßnahmen BT - wie Organisationen die Wirksamkeit von Lernmaßnahmen erhöhen können N2 - Diese Arbeit resultiert in einem Leitfaden, der zur verbesserten Wirksamkeit von Lernmaßnahmen in Organisationen beitragen soll. Inbesondere die Verkürzung der Halbwertszeit von Wissen gab Anlass zur vorliegenden Untersuchung. In den Kapiteln zwei und drei wurde das theoretische Fundament durch Bearbeitung der Themen Personal-/Kompetenzentwicklung, allgemeine und individuelle Lerntheorie, sowie Lernbedarfsanalyse, Lerntransfer und Lernevaluation gebildet. Darauf aufbauend wurde mit der Methodik (Kapitel 4) der Experteninterviews der aktuelle Stand definierter Organisationen im Raum Ostschweiz, Westösterreich und Liechtenstein hinsichtlich Lernbedarfsanalyse, Lerntransfer und Lernevaluation erhoben. Diese Ergebnisse wurden in Kapitel 5 mit der Literaturstudie aus Kapitel 2 und 3 verglichen. Der Leitfaden besteht für Lernbedarfsanalyse, Lerntransfer und Lernevaluation aus unterschiedlichen Schritten, die in Tabellenformat dargestellt und beschrieben sind (Kapitel 6). In Kapitel 7 wurden, neben einer Zusammenfassung und einem Fazit, weiterführende Forschungsansätze zur Thematik angeführt. N2 - This work resulted in a guideline to help improve the effectiveness of learning in organizations. Especially the reduction of the half-life of knowledge was the reason for the underlying study. In chapters two and three, the theoretical foundation was formed by the topics of personnel/competence development, general and individual learning theory, as well as learning needs analysis, learning transfer and learning evaluation. Based on this, the methodology (Chapter 4) for the expert interviews was used to define the status-quo of defined organizations in Eastern Switzerland, Western Austria, and Liechtenstein with regard to learning needs analysis, learning transfer and learning evaluation. In Chapter 5 those results were compared with the theoretical foundations. Based on all previous steps, the guideline is introduced in chapter 6. It consists of different sections for learning needs analysis, learning evaluation, and learning transfer, each of which is presented in table format. In addition to a summary and a conclusion, further research approaches to the topic were listed in Chapter 7. T2 - The effect of learning measures : how organizations can increase the effectiveness of learning activities Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3674 ER - TY - THES A1 - Kreis, Johanna T1 - People Analytics BT - Nutzung und Auswertung von Daten in Prozessen des Personalmanagements N2 - People Analytics wird derzeit in der Fachliteratur und in zahlreichen Studien als eines der Schlüsselthemen für die Zukunft des Personalmanagement behandelt. Analysen sollen helfen, menschliche Arbeitsleistung quantifizierbar zu machen, damit sie besser in die Wertschöpfungskette integriert werden kann. Die technischen Entwicklungen der letzten Jahre, vor allem im Bereich der Künstlichen Intelligenz, dringen auch in die Personalabteilungen vor und immer mehr Produkte kommen auf den Markt, die auf Basis von bestehenden Datensammlungen teils automatisierte und sogar autonome Auswertungen vornehmen können. Die vorliegende Arbeit gibt einen Überblick auf die technischen, rechtlichen und ethischen Faktoren, die beim Einsatz von People Analytics derzeit diskutiert werden. Darüber hinaus wurde - in einem auf Vorarlberg eingegrenzten Survey - den Fragen nachgegangen, ob die hiesigen Unternehmen bereits People Analytics in ihren Personalmanagementprozessen implementiert haben und welche Vor- und Nachteile sie darin sehen. Als Ergebnis wird der Status Quo zum Einsatz von People Analytics in Vorarlberger Unternehmen präsentiert N2 - People Analytics is currently being treated in the specialist literature and in numerous studies as one of the key issues for the future of HR. Analyses should help to make human work performance quantifiable so that it can be successfully integrated into the value chain. The technical developments of recent years, especially in the field of Artificial Intelligence, are also penetrating HR departments and more and more products are introduced into the market that can perform partially automated and even autonomous analysis based on existing data collections. This paper gives an overview of the technical, legal and ethical factors that are currently being discussed when using people analytics. In addition, a survey restricted to Vorarlberg was conducted to find out whether local companies have already implemented people analytics in their HR management processes and what advantages and disadvantages they see in it. As a result, the status quo of the use of people analytics in Vorarlberg companies will be presented. T2 - People Analytics : use and evaluation of data in HR processes Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3677 ER - TY - THES A1 - Stroppa, Katharina T1 - Unternehmenskultur als Erfolgsfaktor BT - Zusammenhang von Unternehmenskultur und Mitarbeiterbindung in Familienunternehmen N2 - Kultur und Werte sind allgegenwärtig in unseren Leben. Sie prägen uns Menschen nicht nur im persönlichen und privaten Umfeld, sondern sind auch Teil von Gesellschaftsstrukturen und Unternehmen. Das Ziel dieser Masterthesis ist es deshalb, herauszufinden, welchen Zusammenhang es zwischen den Themen Unternehmenskultur und Mitarbeiterbindung gibt und ob die Unternehmenskultur in Familienunternehmen dazu beitragen kann eine höhere Mitarbeiterbindung zu schaffen. Dabei werden eine Vielzahl an Motivationsfaktoren, sowie Werten berücksichtigt, welche in einer quantitativen Forschung Aufschluss darüber geben sollen, was den Mitarbeitenden in Vorarlberger Unternehmen wichtig ist und wie diese die Unternehmenskultur in ihren Betrieben wahrnehmen. Mit Hilfe eines standardisierten Fragebogens konnten 151 Personen mit einem Durchschnittsalter von 34,93 Jahren erreicht werden. Dabei wurde ersichtlich, dass die Faktoren angenehme Arbeitsatmosphäre, Jobsicherheit, Weiterbildung/Entwicklung, Führung und Work-Life-Balance die wichtigsten Motivationsfaktoren darstellen. Im Bereich Werte sind Verlässlichkeit, Ehrlichkeit, Verantwortungsbewusstsein, Respekt und Fairness am wichtigsten. Diese Erkenntnisse konnten unabhängig von der Unternehmensform erlangt werden. N2 - Culture and values are omnipresent in our lives. They not only shape us personally and privately, but are also part of social structures and companies. The goal of this master's thesis is therefore to find out, what connection there is between the topics of corporate culture and employee loyalty and whether corporate culture in family businesses can contribute to creat greater employee loyalty. A variety of motivational factors and values are taken into account, which should provide information in a quantitative research about what is important to the employees of Vorarlberg and how they perceive the corporate culture in their companies. With the help of a standardized questionnaire, people with an average age of 34.93 years were reached. It became apparent, that the factors pleasant working atmosphere, job security, further training/development, leadership and work-life balance are the most important motivating factors. In the area of values, reliability, honesty, sense of responsibility, respect and fairness are the most important. The results were achieved regardless of the form of the company. T2 - Corporate culture as a success factor : relationship between corporate culture and employee retention in family businesses KW - Unternehmenskultur KW - Mitarbeiterbindung KW - Erfolgsfaktor Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3707 ER - TY - THES A1 - Venc, Isabella T1 - Interne Wissensvermittlung durch Blended Learning BT - wie können kombinierte Lernmethoden zur Fachkräfteentwicklung in Vorarlberger Industriebetrieben beitragen? N2 - Die Psychologie beschreibt Lernen als dauerhafte Veränderung des individuellen Wesens oder Verhaltens, basierend auf Erfahrungen. Multimediale Lernmethoden ermöglichen hierbei, den Prozess in der betrieblichen Weiterbildung zu unterstützen und zu optimieren, um den steigenden Anforderungen, gerade im Bereich der Fachkräfteentwicklung, standhalten zu können. Im ersten Teil dieser Arbeit werden die theoretischen Grundlagen der Personalentwicklung, mit Fokus auf der betrieblichen Weiterbildung, sowie des Lernens umfassend erläutert. Im zweiten Teil werden die Ergebnisse einer qualitativen Forschung anhand drei verschiedener Perspektiven über die Lernmethoden E-Learning, Präsenztraining und Blended Learning in fünf Vorarlberger Industrieunternehmen präsentiert. Eine Schlussbetrachtung mit dem Ergebnis der Forschungsfrage sowie einem Ausblick für mögliche weiterführende Forschungsansätze runden die Arbeit ab. Ziel dieser Masterarbeit ist die praxisorientierte Anwendbarkeit der Erkenntnisse für Vorarlberger Industriebetriebe in Bezug auf die interne Weiterbildung, insbesondere bei der Entwicklung von Fachkräften. N2 - Psychology describes learning as a permanent change in individual nature or behavior, based on experience. Multimedia learning methods support and optimize the learning process of on-the-job trainings, in order to be able to withstand the increasing requirements, particularly in the area of skilled worker development. The first part of this thesis deals with the theoretical basics of personnel development, with a focus on in-company trainings and learning. In the second part, the results of a qualitative research are presented using three different perspectives on the learning methods e-learning, classroom training and blended learning in five industrial companies in Vorarlberg. The work is rounded off by a final analysis with answers to the research question, as well as an outlook for possible further research approaches. The aim of this master´s thesis is the practical applicability of the research for industrial companies in Vorarlberg in relation to the development of skilled workers. T2 - Internal knowledge transfer through Blended Learning : how can combined learning methods contribute to the development of skilled employees? KW - Blended Learning KW - Wissensmanagement KW - Fachkräfteentwicklung KW - Lernmethoden KW - Interne Wissensvermittlung Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3672 ER - TY - THES A1 - Rauch, Bernd T1 - Die vier Tage Arbeitswoche BT - Nutzen und Auswirkungsanalyse N2 - Das Ziel der vorliegenden Masterarbeit war es, den Nutzen einer 4-Tage-Woche einerseits für Mitarbeiter, aber auch für Unternehmen herauszufinden. Dazu wurde als erstes herausgefunden, welche Auswirkungen die Arbeitszeit auf Mitarbeiter haben kann und inwiefern das immer wichtiger werdende Thema Work-Life-Balance davon betroffen ist. Als nächster Schritt wurden Erfahrungsberichte von Unternehmen, sowie derer Mitarbeiter analysiert. Derzeit gibt es noch nicht viele Länder und Unternehmen, welche sich für eine 4-Tage-Woche einsetzen, weshalb diejenigen, die eine 4-Tage-Woche befürworten oder eingeführt haben, große mediale Aufmerksamkeit erhalten und regelmäßig interviewt werden. Daraufhin wurden weitere Arbeitszeitmodelle analysiert, welche als Alternative für den Zweck einer besseren Work-Life-Balance und auch bessere Wettbewerbsfähigkeit für Unternehmen eingesetzt werden können. Dann folgte die empirische Analyse, wobei Experteninterviews und auch eine quantitative Umfrage in Vorarlberg durchgeführt wurden. Dabei wurden einerseits Kenner der 4-Tage-Woche, aber auch Nicht-Kenner befragt und diese Umfrageergebnisse miteinander verglichen. Als letzter Schritt wurde Kontakt mit einer bekannten Unternehmensberaterin aufgenommen, welche Spezialistin im Bereich Change-Management und Organisationsentwicklung ist. Somit wurde eine Handlungsempfehlung zur Implementierung einer 4-Tage-Woche ausgearbeitet. Diese Masterarbeit ist sowohl für Entscheidungsträger im Personalbereich, als auch für all jene Dienstnehmer, welche ihre Work-Life-Balance für wichtig erachten. N2 - The aim of this master's thesis was to find out the benefits of a 4-day week for employees, as well as for companies. The first step was to find out what effects working time can have on employees and to what extent this affects the increasingly important work-life balance. The next step was to analyze the experience reports of companies and their employees. At the moment there are not many countries and companies that campaign for a 4-day week, which is why those who advocate or have introduced a 4-day week receive a lot of media attention and are interviewed regularly. As a result, further working time models were analyzed, which can be used as an alternative for the purpose of a better work-life balance and also better competitiveness for companies. Then followed the empirical analysis, with expert interviews and a quantitative survey conducted in Vorarlberg. On the one hand, experts from the 4-day week, which already were working in a 4-day-week, but also non-experts, were interviewed and the results of the survey were compared. As a last step, contact was made with a well-known management consultant who is a specialist in change management and organizational development. Thus, a recommendation for action to implement a 4-day week was drawn up. This master's thesis is for decision-makers in the personnel area, as well as for all those employees who consider their work-life balance to be important. T2 - The four days working week : benefit and impact analysis KW - 4-Tage-Woche KW - Arbeitszeitreduktion Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3713 ER - TY - THES A1 - Weber, Michelle T1 - Evaluierung von Intrusion-Detection-Systemen und Visualisierungstools für die Darstellung deren Ergebnisse im Rahmen einer digitalen Fabrik N2 - Für die Digitale Fabrik an der FH Vorarlberg sollen Intrusion-Detection-Systeme (IDS) zur Erkennung von Angriffen auf Hosts sowie im Netzwerk evaluiert werden. Außerdem sollen die aus den IDS erhaltenen Resultate so dargestellt werden, damit Systemadministratorinnen rapide Entscheidungen bezüglich der generierten Alarme treffen können. Um dies zu gewährleisten sollen neben den IDS zusätzlich entsprechende Visualisierungstools evaluiert werden. In dieser Arbeit werden dazu unterschiedliche signatur- sowie auch anomaliebasierte Netzwerk- und Host-IDS technisch beschrieben und anhand von Kriterien, welche aus den Anforderungen abgeleitet werden, bewertet. Zusätzlich wird die Genauigkeit der IDS durch Testen von spezifischen Angriffen ermittelt. Außerdem werden potenzielle Tools für die Darstellung von Alarmen aus den IDS vorgestellt und ebenfalls anhand den Anforderungen aufgezeigt, welches am geeignetsten ist. Abschließend werden alle Probleme sowie Erkenntnisse aufgezeigt, welche während der Evaluierung auftraten und erläutert, wie diese Arbeit fortgeführt werden kann. N2 - For the Digital Factory at the FH Vorarlberg, intrusion detection systems (IDS) for detection of attacks on hosts as well as in the network should be evaluated. In addition, the results of the IDS should be presented in such a way that system administrators can make rapid decisions regarding the generated alarms. In order to ensure this, appropriate visualization tools should be evaluated additionally. In this thesis, different signature- as well as anomaly-based network and host IDS are technically described and evaluated based on criteria derived from the requirements. What is more, the accuracy of the IDS is determined by testing specific attacks. Furthermore, suitable tools for the representation of alarms generarted from the IDS are presented and the most applicable ones are determined based on the requirements. Moreover, all problems that occurred during the evaluation of the systems as well as the findings of this work will be presented. Finally, it will be explained how future work could be derived from this thesis. T2 - Evaluation of intrusion detection systems and visualization tools for depicting their results in a digital factory KW - Intrusion detection system KW - Visualization tool KW - IDS Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3738 ER - TY - THES A1 - Starcevic, Nikolai T1 - Approaches for dealing with structural- and rounded zeros in data mining tasks N2 - Zeros can cause many issues in data analysis and dealing with them requires specialized procedures. We differentiate between rounded zeros, structural zeros and missing values. Rounded zeros occur when the true value of a variable is hidden because of a detection limit in whatever mechanism was used to acquire the data. Structural zeros are values which are truly zero, often coming about due to a hidden mechanism separate from the one which generates values greater than 0. Missing values are values that are completely missing for unknown or known reasons. This thesis outlines various methods for dealing with different kinds of zeros in different contexts. Many of these methods are very specific in their ideal usecase. They are separated based on which kind of zero they are intended for and if they are better suited for compositional or for standard data. For rounded zeros we impute the zeros with an estimated value below the detection limit. The author describes multiplicative replacement, a simple procedure that imputes values at a fixed fraction of the detection limit. As a more advanced technique, the author describes Kaplan Meier smoothing spline replacement, which interpolates a spline on a Kaplan Meier curve and uses the spline below the detection limit to impute values in a more natural distribution. Rounded zeros cannot be imputed with the same techniques that would be used for regular missing values, since there is more information available on the true value of a rounded zero than there would be for a regular missing value. Structural zeros cannot be imputed since they are a true zero. Imputing them would falsify their values and produce a value where there should be none. Because of this, we apply modelling techniques that can work around structural zeros and incorporate them. For standard data, the zero inflated Poisson model is presented. This model utilizes a mixture of a logistic and a Poisson distribution to accurately model data with a large amount of structural zeros. While the Poisson distribution is only applicable to count data, the zero inflation concept can be applied to different kinds of distributions. For compositional data, the zero adjusted Dirichlet model is introduced. This model mixes Dirichlet distributions for every pattern of zeros found within the data. Non-algorithmic techniques to reduce the amount of structural zeros present are also shown. These techniques being amalgamation, which combines columns with structural zeros into more broad descriptors and classification, which changes columns into categorical values based on a structural zero being present or not. Missing values are values that are completely missing for various known or unknown reasons. Different imputation techniques are introduced. For standard data, MissForest imputation is introduced, which utilizes a RandomForest regression to impute mixed type missing values. Another imputation technique shown utilizes both a genetic algorithm and a neural network to impute values based on the genetic algorithm minimizing the error of an autoencoder neural network. In the case of compositional data, knn imputation is presented, which utilizes the knn concept also found in knn clustering to impute the values based on the closest samples with a value available. All of these methods are explained and demonstrated to give readers a guide to finding the suitable methods to use in different scenarios. The thesis also provides a general guide on dealing with zeros in data, with decision flowcharts and more detailed descriptions for both compositional and standard data being presented. General tips on getting better results when zeros are involved are also given and explained. This general guide was then applied to a dataset to show it in action. N2 - Nullen können viele Probleme in Datenanalyse verursachen. Ihre Präsenz blockiert bei Kompositionalen Daten die wichtige Log-Transformation und führt bei Standarddaten zu schlecht angepassten Verteilungen. Mit ihnen umzugehen benötigt spezielle Verfahren. Wir unterscheiden zwischen gerundeten Nullen, strukturellen Nullen und fehlenden Werten. Gerundete Nullen zeigen sich in Daten wenn der echte Wert einer Variable versteckt ist weil der Mechanismus der die Werte ausgibt ein Detektionslimit aufweist. Strukturelle Nullen sind Nullen die wirklich Null sind, und keinen Wert maskieren. In vielen Fällen werden sie durch einen seperaten Prozess generiert, als Werte die keine Strukturelle Null sind. Fehlende Werte sind Werte die wegen bekannten oder unbekannten Gründen vollkommen fehlen. Diese Arbeit beschreibt verschiede Methoden um mit verschiedenen Arten von Nullen in verschiedenen Umständen umzugehen. Viele von diesen Methoden sind spezifisch für ihr Einsatzgebiet. Sie sind basierend darauf getrennt für welche Nullen sie gedacht sind und ob sie besser für Kompositionale oder Standarddaten gedacht sind. Für gerundete Nullen setzen wir Werte in die Null ein, die unter dem Detektionslimit liegen. Der Author beschreibt multiplikatives Ersetzen, eine einfache Prozedur die Nullen durch einen fixen Teil des Detektionslimits ersetzt. Als fortgeschrittenere Technik wird “Kaplan Meier Smoothing Spline replacement” beschrieben, welche ein Spline auf einer Kaplan Meier Kurve interpoliert und die Werte unter dem Detektionslimit benutzt um die Werte in einer natürlicheren Verteilung einzusetzen. Gerundete Nullen können nicht mit den selben Methoden ersetzt werden wie fehlende Werte da bei gerundeten Nullen mehr Information zu Verfügung steht, nämlich das sie unter einem gewissen Limit liegen. Strukturelle Nullen können nicht ersetzt werden da sie wirklich Null sind. Sie zu ersetzen würde die Daten verfälschen und einen Wert produzieren wo eigentlich keiner vorkommt. Deswegen benutzen wir Modellierungstechniken die um sie herum arbeiten und sie mit ins Modell einbeziehen. Für Standarddaten wird das “Zero Inflated Poisson Model” vorgestellt. Dieses Model benutzt eine Mixtur von einer logistischen und einer Poissonverteilung um Daten mit vielen Nullen genau darzustellen. Man kann die Poisson Verteilung zwar nur für Zähldaten benutzen, allerdings ist das Konzept der “Zero Inflation” auch für andere Verteilungen benutzbar. Für kompositionale Daten wird das logistische Mixturmodell vorgestellt. Diese Modell vermischt logistische Verteilungen für jedes Muster von Nullen in einem Datensatz. Nicht-algorithmische Techniken um strukturelle Nullen zu reduzieren werden auch gezeigt. Diese Techniken sind “Amalgamation”, wobei mehrere Spalten miteinander kombiniert werden um einen übersichtlicheren Wert darzustellen, und Klassifizierung, wobei eine Spalte in eine kategorische Variable geändert wird die anzeigt ob der Wert eine strukturelle Null oder nicht ist. Als fehlender Wert werden Werte beschrieben die unter verschiedenen Umständen nicht im Datensatz präsent sind. Verschiedene Techniken, um diese zu ersetzen, werden vorgestellt. Für Standarddaten wird die MissForest Imputierung vorgestellt, welche eine RandomForest Regression benutzt um gemischte Daten einzusetzen, also Daten die sowohl kontinuierliche als auch kategorische Variablen enthalten. Eine Weitere Methode benutzt einen genetischen Algorithmus und ein Neuronales Netz um Werte einzusetzen. Dies wird erreicht in dem der Genetische Algorithmus die Eingabe in ein Autoenkodierer Netzwerk so optimiert das der Fehler minimiert ist. Für kompositionale Daten wird KNN Imputation vorgestellt, welche das KNN Konzept benutzt, das auch in KNN Clustering benutzt wird, um Variablen basierend auf den nächsten Einträgen zu imputieren. All diese Methoden werden erklärt und demonstriert um dem Leser/der Leserin eine Anleitung zu geben um die richtige Methode für das richtige Umfeld zu finden. Die Arbeit stellt ebenfalls eine generelle Anleitung bereit um mit Nullen umzugehen. Es werden Ablaufdiagramme und genaue Beschreibungen für Kompositionale- und Standarddaten vorgestellt. Generelle Hinweise um bessere Ergebnisse bei der Analyse mit Nullen zu erhalten werden auch gegeben und erklärt. Im anschließenden Teil wurde diese Anleitung beispielsweise eingesetzt. KW - Rounded zeros KW - Structural zeros KW - Compositional data KW - Missing values KW - Data analysis Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3703 ER - TY - THES A1 - Bechtold, Florian T1 - Konzipierung eines Baukastensystems zur Erstellung von Berichten in einem Business Warehouse am Beispiel der Hexagon Geosystems N2 - Business Intelligence (BI) beschreibt den Bereich, der für die Auswertung betrieblicher Geschäftsdaten verantwortlich ist und von Unternehmen jeder Größe verwendet wird. Die erhaltenen Informationen unterstützen die Entscheidungsfindung von Unternehmen und können sich positiv auf die Geschäftsentwicklung auswirken. Die Hexagon Geosystems hat seit mehreren Jahren Lösungen im Einsatz, mit welchen die systematische Analyse von Geschäftsdaten abgewickelt wird. Für Unternehmen dieser Größe sind leicht zugängliche und benutzerfreundliche BI-Lösungen unerlässlich - über die Jahre und der wachsenden Menge an Analysen und Berichten haben sich aber Probleme in der Verwendung und Verständlichkeit gebildet, welche im Rahmen dieser Masterarbeit untersucht werden. Zum Beginn werden die theoretischen Inhalte der Arbeit erläutert und eine Wissensgrundlage geschaffen. Aus der in der Ist-Analyse gegebenen Beschaffenheit im Unternehmen werden die Probleme der aktuellen Lösung im Rahmen einer Problemerläuterung aufgewiesen. Die daraus resultierenden Erkenntnisse bilden die Grundlage für die Konzipierung eines Proof of Concepts in den darauf folgenden Kapiteln. In dem Proof of Concept wird ein Vorschlag für ein Baukastensystem zur Erstellung von Berichten und dessen Dokunentationen präsentiert. Eine mittels der System Usability Scale durchgeführten Evaluation zeigte, dass eine benutzungsfreundliche Applikation entstanden ist, welche neben Vorteilen für die Endanwender des Business Warehouses auch Vorteile für die Administratorinnen bei der Erstellung von Berichten mit sich bringt. Eine Zusammenfassung und ein abschließender Ausblick weist diverse Arbeitsschritte auf, welche zur Integration der Applikation in die produktive Landschaft des Unternehmens benötigt werden. N2 - Business Intelligence (BI) describes the area responsible for the evaluation of operational business data and is used by companies of all sizes. The obtained information supports the decision-making process of companies and has a positive effect on business development. Hexagon Geosystems has been using solutions for the analysis of business data for serveral years. For companies of this size, easily accessible and user-friendly BI solutions are essential - the growing volume of analyses and reports over the years has however lead to problems in its usability and comprehensibility, which are investigated in the context of this master thesis. At the beginning of the thesis the theoretical contents are introduced and a knowledge base is created. The problems of the current solution are shown in the context of a problem explanation based on findings within the company during the as-is analysis. The resulting findings and problems form the basis for designing a proof of concept in the following chapters. In the proof of concept, a proposal for a modular system for creating reports and their documentation is presented. An evaluation carried out using the System Usability Scale showed that a user-friendly application has been created which, in addition to advantages for the end users of the business warehouse, also has advantages for the administrators when creating reports. A summary and a final outlook shows various work steps that are required to integrate the application into the company’s productive landscape. KW - Data warehouse KW - Business intelligence Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3681 ER - TY - THES A1 - Bauer, Christoph T1 - A case study on automated classification, mathematical model generation and solution space exploration of formalised product knowledge N2 - This thesis aims to support the product development process. Therefore, an approach is developed, implemented as a prototype and evaluated, for automated solution space exploration of formally predefined design automation tasks holding the product knowledge of engineers. For this reason, a classification of product development tasks related to the representation of the mathematical model is evaluated based on the parameters defined in this thesis. In a second step, the mathematical model should be solved. A Solver is identified able to handle the given problem class. Due to the context of this work, System Modelling Language (SysML) is chosen for the product knowledge formalisation. In the next step the given SysML model has to be translated into an object-oriented model. This translation is implemented by extracting information of a ".xml"-file using the XML Metadata Interchanging (XMI) standard. The information contained in the file is structured using the Unified Modelling Language (UML) profile for SysML. Afterwards a mathematical model in MiniZinc language is generated. MiniZinc is a mathematical modelling language interpretable by many different Solvers. The generated mathematical model is classified related to the Variable Type and Linearity of the Constraints and Objective of the generated mathematical model. The output is stored in a ".txt"-file. To evaluate the functionality of the prototype, time consumption of the different performed procedures is measured. This data shows that models containing Continuous Variables need a longer time to be classified and optimised. Another observation shows that the transformation into an object-oriented model and the translation of this model into a mathematical representation are dependent on the number of SysML model elements. Using MiniZinc resulted in the restriction that models which use non-linear functions and Boolean Expressions cannot be solved. This is because the implementation of non-linear Solvers at MiniZinc is still in the development phase. An investigation of the optimally of the results, provided by the Solvers, was left for further work. N2 - Diese Arbeit zielt darauf ab, den Produktentwicklungsprozess zu unterstützen. Dazu wird ein Ansatz zur automatisierten Untersuchung von Lösungsräumen von formal vordefinierten Entwurfsautomatisierungsaufgaben, die das Produktwissen von Ingenieuren beinhalten, gesucht, umgesetzt und evaluiert. Dazu wird eine Klassifikation von Produktentwicklungsaufgaben, die sich auf das darstellende mathematische Modell beziehen, anhand der in dieser Arbeit definierten Parameter evaluiert. In einem zweiten Schritt soll das mathematische Modell gelöst werden. Es wird ein Solver identifiziert, der in der Lage ist, die gegebene Problemklasse zu bearbeiten. Aufgrund des Kontextes dieser Arbeit wird System Modelling Language (SysML) für die Formalisierung des Produktwissens gewählt. In einem nächsten Schritt muss das gegebene SysML Modell in ein objektorientiertes Modell übersetzt werden. Diese Übersetzung wird durch Extraktion von Informationen aus einer Extensible Markup Language (XML)-Datei unter Verwendung des XML Metadata Interchanging (XMI) Standards realisiert. Die in der Datei enthaltenen Informationen werden unter Verwendung des Unified Modelling Language (UML) Profils für SysML strukturiert. Anschließend wird ein mathematisches Modell in der Sprache MiniZinc generiert. MiniZinc ist eine mathematische Modellierungssprache, die von vielen verschiedenen Solvern interpretiert werden kann. Das generierte mathematische Modell wird in Bezug auf Variablentyp, sowie Linearität der Constraints und Objektivs des Modells klassifiziert. Die Ausgabe wird in einer ".txt"-Datei gespeichert. Um die Funktionalität des Prototyps zu bewerten, wird der Zeitaufwand der verschiedenen durchgeführten Verfahren gemessen. Diese Messungen zeigen, dass Modelle, die Kontinuierliche Variablen enthalten, länger brauchen, um klassifiziert und optimiert zu werden. Eine weitere Beobachtung zeigt, dass die Transformation in ein objektorientiertes Modell und die Übersetzung dieses Modells in eine mathematische Repräsentation von der Anzahl der SysML Modellelemente abhängig ist. Die Verwendung von MiniZinc führte zu der Einschränkung, dass Modelle, die nicht-lineare Funktionen und Boolesche Ausdrücke verwenden, nicht gelöst werden können. Dies liegt daran, dass sich die Implementierung von nicht-linearen Solvern bei MiniZinc noch in der Entwicklungsphase ist. Eine Untersuchung des Optimums der von den Solvern gelieferten Ergebnisse wird für eine weiterführende Arbeit vorgeschlagen. T2 - Eine Fallstudie zur automatisierten Klassifikation, mathematische Modellgenerierung und Untersuchung des Lösungsraums von formalisiertem Produktwissen KW - SysML KW - Mathematical modell generation KW - Automated optimisation Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3715 ER - TY - THES A1 - Rauch, Anna Malena T1 - Motivationssteigerung zur genaueren Arbeitszeitdokumentation mittels Gamification N2 - Für die Verrechnung von Leistungen gegenüber dem Kunden sowie die Planung des weiteren Geschäftsjahres ist es wichtig, dass die Angestellten ihre Arbeitszeit so genau wie möglich dokumentieren. Da diesbezüglich bei der Firma IMA-Systems Information-Technology ZNL der NEXTCLINICS Austria GmbH (im Folgenden IMA-Systems) Verbesserungspotential besteht, gilt es Lösungen zu finden die Angestellten zu motivieren ihre Arbeits-Dokumentation möglichst genau anzufertigen. Gamification hat sich in vielen Bereichen als Hilfreich herausgestellt, wenn es um die Motivationssteigerung von Menschen geht. In dieser Arbeit wird der Fragestellung nachgegangen, inwiefern mittels Gamification die Motivation zur genaueren Zeitdokumentation der Arbeitnehmenden im Unternehmen IMA-Systems gesteigert werden kann. Um die Fragestellung zu beantworten wird eine Gamification-Anwendung entwickelt, welche die Angestellten zu einer genaueren Dokumentation ihrer Arbeitszeit motivieren soll. Hierfür wird mittels des User Centered Design Prozesses ein VB.Net Programm implementiert, welches mit Hilfe der passenden Spielelemente zur Motivationssteigerung beitragen soll. Hierbei wird unterschieden ob es sich um ein Mitglied der Entwicklungs- oder EDV-Abteilung handelt, da die Dokumentation sich in den Abteilungen unterscheidet. Während die Entwicklungsabteilung zeitgleich und minutengenau dokumentiert, dokumentiert die EDV-Abteilung indem nachträglich Zeiteinheiten zugeordnet werden. Vor der Implementierung der Anwendung werden die Teilnehmenden interviewt, um ihre Antworten in die Entwicklung einfließen zu lassen. Nach Fertigstellung des Prototyps wird die Testphase eingeleitet. Hierfür wird der Prototyp in den Arbeitsalltag der Angestellten der Firma IMA-Systems integriert. Auf die Feldphase folgen eine erneute Befragung der Angestellten sowie der Vergleich der Daten vor und nach der Einführung von Gamification. Die Auswertung der Ergebnisse ergab, dass die Anwendung auf die EDV-Abteilung mit einer Steigerung von 18,6% einen deutlichen, positiven Effekt hat, welcher sich in der Entwicklungsabteilung mit einem Rückgang von 5% nicht verzeichnen lässt. In der abschließenden Diskussion wird die Auswertung der Ergebnisse kritisch betrachtet, der Grund für die Verschlechterung in der Entwicklungsabteilung erläutert und ein Ausblick für mögliche Verbesserungen und Erweiterungen des Prototyps aufgezeigt. N2 - In order to invoice services to the customer and the planning of the further business year, it is important that the employees document their working hours as accurately as possible. As there is potential for improvement at IMA-Systems Information-Technology ZNL of NEXTCLINICS Austria GmbH (in the following IMA-Systems), it is important to find solutions and motivate the employees to prepare their work documentation as accurately as possible. Gamification has proven to be helpful in many areas when it comes to increasing the motivation of people. In this thesis the question is investigated, to what extent gamification can increase the motivation of employees in the company IMA-Systems to produce more precise time documentation. In order to answer this question, a gamification application will be developed, which should motivate the employees to a more exact documentation of their working time. For this purpose, a VB.Net program will be implemented using the User Centered Design process, which will help to increase motivation with the help of suitable game elements. It is distinguished whether the employee belongs to the development or EDP department, since the documentation differs in the different departments. While the development department documents simultaneously and to the minute, the EDP department documents by assigning time units at a later time. Before the application is implemented, the participants are interviewed to incorporate their answers. After completion of the prototype, the test phase is initiated. For this purpose, the prototype is integrated into the everyday work of the employees of IMA-Systems. The field phase is followed by a new survey of the employees and the comparison of the data before and after the introduction of gamification. The evaluation of the results showed a clear positive effect of the application on the EDP department with an increase of 18.6%, which cannot be seen in the development department with a decrease of 5%. In the concluding discussion, the evaluation of the results is critically reviewed, the reason for the deterioration in the development department is explained and an outlook for possible improvements and extensions of the prototype is given. T2 - Motivation increase for more accurate working time documentation through gamification KW - Gamification KW - Arbeitszeitdokumentation Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3720 ER - TY - THES A1 - Pfeil, Andreas T1 - Mental health risk assessment on workplace BT - the role of stigmatization in the DACH-Region N2 - How people perceive stigmatization at work in connection with mental health problems and what role this stigmatization fulfils in the DACH-Region, means Germany-Austria-Switzerland, has so far received no greater attention from scientists. Although the stigma of mental illness has been extensively researched among the general population, little is known about its consequences of the stigma of mental health in the workplace. This study seeks to bridge the gap in this area. As the purpose of this thesis is to illustrate the dynamics of stigmatization rather than to explain its mere quantitative relevance, I have chosen to investigate how the complex systemic interdependencies according to Forrester (1968) manifest in the reflection of the subjects. On the background of socio-cultural aspects in the DACH-Region regarding mental health problems and forms and natures of stigma while following the question what role stigmatization plays in this German-speaking area DACH, I conducted a qualitative social research study with affected persons (employees from various German companies) to investigate this issue. Hereby I focus on people working in the industry sector. The present thesis begins by exploring the question of intercultural and sociocultural differences in the DACH region according to Hofstede’s Dimensions, as well as their possible relevance for answering the research question. Definitions and theoretical interpretations regarding the backgrounds about mental health, mental health problems and their appearance will be mentioned. Based on Goffman’s (1963) research on stigma, I investigate why mental health issues have the potential to stigmatize especially at the workplace. Goffman’s ideas on stigma illustrate how by providing important insights into understanding the situation of affected persons. The connection between stereotypes, stigmatization, and discriminatory behaviour according to Major & O’Brien (2005) is hereby necessary to be noticed. Through personal interviews I explore how, what way, people at work perceive stigmatization surrounding mental health problems and how stigmas interact. The findings conducted in this study give a cue towards the systemic approach of stigmatization. That is why a new hypothesis on the ways of stigmatization in German-speaking countries is drawn up. Stigmatization is under investigation as a systemic instrument for maintaining management and group power to affect single employees and restore group identity, consciously or unconsciously. I discuss the theoretical and practical implications of these findings for management behaviour and leadership development in organizations. KW - Mental health KW - Stigma KW - Stigma-Loop KW - Discrimination KW - Leadership Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3750 ER - TY - THES A1 - Büsel, Philipp T1 - Project management maturity models BT - a structured comparison N2 - For centuries, companies and institutions are working on the development of organisational project maturity models. The purpose of these models is to develop a path for improving an organisation’s capability of managing projects. Projects are the means by which companies implement their strategic objectives. Trends like globalisation and advances in IT lead to more geographically distributed teamwork. Therefore, this thesis gives a comprehensive answer to how project management maturity models address transnational project management. For accomplishing the research objective, this thesis follows an integrated, qualitative literature review approach. Theoretical frameworks and applied research on project management maturity assessments were systematically collected and analysed. The results extracted from these two sources were synthesised to extract findings. The main research result shows that models continuously adapt to transnational project management. They are doing this by aligning the organisational culture and values, focusing on organisational wide learning and gradually embedding behavioural and intercultural competencies. Maturity assessments need to follow this trend. Furthermore, transnational convergence of the models’ dimensions was observed. This development leads to growth in size and complexity. To apply them internationally, the models should be simplified or easily adapted to specific countries and cultures. KW - Project management KW - Project management maturity model KW - Organisational project management KW - Trans-national project management Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3736 ER - TY - THES A1 - Battisti, Markus T1 - Global innovation management systems BT - a case study analysis of the automotive industry N2 - Increasing international competition and accelerated technological change characterize the environment in which companies must maintain and, if possible, expand their competitive advantage. In this context, the new, popular keyword innovation management is often mentioned. Many corporations propagate and use it for marketing purposes. As a result, the companies have to evaluate, develop and launch innovations increasingly faster, which poses great challenges for many and requires a high degree of adaptability. This master thesis analyzes innovation management (IM) in the automotive industry and in other industries (material manufacturers, service providers, medicine, ...) depending on the number of employees and turnover. In addition, the maturity levels of the IMs and the innovation management systems (IMS) are examined. It also tries to determine which design or "building blocks" are necessary for a successful innovation management. Furthermore, factual and monetary guidelines by the management are evaluated. The thesis also aims to find out how the success of IM is measured. Therefore, guideline-based expert interviews were conducted with responsible people from the innovation departments and then systematically analyzed. In the literature, expenses for innovations are often wrongly equated with the R&D rate. In this master thesis, it could be shown that this ratio is highest in the automotive industry. However, it does not correlate with the number of employees, turnover, maturity level, success or design of the IM. Furthermore, it could be shown that larger companies have a higher degree of maturity. The reason for this is that more people are usually involved in innovation and that a holistic understanding of innovation is better anchored in large corporations. When designing the IM or the roles of the innovation department, large companies use several different types. While the IM departments in small and medium-sized companies are usually incubators and accelerators, large companies also use corporate venture capital to support start-ups and develop new business models. In this thesis, the success of IM was determined by the number of innovations implemented in customer projects. It was found that, regardless of the size of the company, a higher degree of maturity of the IM and the accelerator role seem to have a positive influence. Unfortunately, there are rarely concrete goals and targets set by the management although these, along with a holistic understanding of innovation in the company, are without doubt the most important part of a successful innovation management. N2 - Zunehmender internationaler Wettbewerb und beschleunigter technologischer Wandel kennzeichnen das Umfeld, in dem Unternehmen ihren Wettbewerbsvorteil erhalten und, wenn möglich, ausbauen müssen. In diesem Kontext wird oft das neue, populäre Schlagwort Innovationsmanagement genannt, welches mittlerweile von vielen Konzernen propagiert und marketingtechnisch genutzt wird. Konzerne müssen demzufolge Innovationen immer schneller bewerten, ausarbeiten und auf den Markt bringen, was viele vor große Herausforderungen stellt und ein hohes Maß an Anpassungsfähigkeit verlangt. Die vorliegende Masterarbeit analysiert das Innovationsmanagement (IM) in der Automobilindustrie sowie in anderen Branchen (Materialhersteller, Dienstleister, Medizin, …) in Abhängigkeit von Mitarbeiteranzahl und Umsatz. Zusätzlich wird untersucht, wie hoch der Reifegrad des IM und der Innovationsmanagementsysteme (IMS) ist und welches Design bzw. welche „Bausteine“ für ein erfolgreiches Innovationsmanagement notwendig sind. Darüber hinaus wird analysiert, welche fachlichen und monetären Vorgaben es von der Geschäftsführung gibt und wie der Erfolg des IM gemessen wird. Dabei werden leitfadengestützte Experteninterviews mit Verantwortlichen aus den Innovationsabteilungen geführt und diese dann systematisch ausgewertet. Ausgaben für Innovationen werden in der Literatur oft fälschlicherweise mit der F&E-Quote gleichgesetzt. Es konnte in dieser Arbeit gezeigt werden, dass diese Quote in der Automobilindustrie am höchsten ist, jedoch nicht mit der Mitarbeiteranzahl, dem Umsatz, dem Erfolg, dem Reifegrad bzw. dem Design des IM korreliert. Weiters konnte festgestellt werden, dass größere Unternehmen einen höheren Reifegrad besitzen. Der Grund dafür ist, dass sich normalerweise mehr Personen mit Innovationen beschäftigen und, dass ein ganzheitliches Verständnis für Innovation in Großkonzernen besser verankert ist. Beim Design des IM bzw. den Rollen der Innovationsabteilung verwenden große Unternehmen mehrere unterschiedliche Typen. Während die IM-Abteilungen in kleinen und mittelgroßen Unternehmen meist Inkubatoren und Acceleratoren sind, verwenden Großunternehmen zusätzlich auch Corporate Venture Capital um Start-Ups zu fördern und neue Geschäftsmodelle zu entwickeln. Der Erfolg des IM wurde in dieser Arbeit über die Anzahl von umgesetzten Innovationen in Kundenprojekten bestimmt. Dabei konnte festgestellt werden, dass, unabhängig von der Größe des Unternehmens, ein höherer Reifegrad des Innovationsmanagement sowie Acceleratoren einen positiven Einfluss zu haben scheinen. Konkrete Ziele und Vorgaben von der Geschäftsführung gibt es leider nur selten, obwohl diese, neben dem ganzheitlichen Verständnis für Innovation im Unternehmen, ohne Zweifel, den wichtigsten Teil für ein erfolgreiches Innovationsmanagement darstellen. KW - Global innovation management system KW - Innovation management system KW - Innovation management KW - Case study analysis KW - Automotive industry Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3719 ER - TY - THES A1 - Madan, Saurabh T1 - Influence of culture in the acceptance of digital tools in leadership communication N2 - The workplaces are changing with the increase in the use of technology, digital communication, the shift towards multicultural teams, and remote work due to COVID-19. Leaders need more collaboration and acceptance of digital communication tools such as Teams, Slack. This study aims to determine the influence of culture in the acceptance of digital tools in leadership communication. In the literature review, 3 cultures (organizational, national, Individual) were assumed. And Individual culture was tested using Schwartz (openness to change) value survey along with other qualitative questions in 1-1 interviews of Austrians and multinationals living in Austria. Analysis from findings suggests that culture plays an important role in technology acceptance of digital tools in leadership communication. This was confirmed by the Schein model and Schwartz value ratings. The culture comprises of organizational, national, regional, and individual culture. Individual culture plays an important role, but other cultural factors cannot be avoided. Key factors affecting the technology acceptance in Vorarlberg (Austria) are listed along with recommendations to leaders. KW - Leadership digital communication tools KW - Culture and leadership KW - Technology acceptance in leadership and influence of culture KW - Digital collaboration tools teams, slack, skype KW - Vorarlberg Austria Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3737 ER - TY - THES A1 - Jochum-Müller, Sabine T1 - Auswirkung der Social Impact-Orientierung auf Instrumente der Unternehmenssteuerung BT - eine Einzelfallstudie eines Sozialunternehmens in Österreich N2 - Veränderungen im gesellschaftlichen Wertesystem, das Vordringen kommerzieller Privatwirtschaft in Bereiche, die über lange Zeit von Non-Profit-Organisationen abgedeckt worden sind, und die Finanzkrise der öffentlichen Haushalte gelten als große Ursachen für die vielfältige und kontroversielle Diskussion der Social Impact-Orientierung im deutschsprachigen Raum. Diese Arbeit konzentriert sich auf die Frage, wie sich Social Impact-Orientierung auf Instrumente der Unternehmenssteuerung auswirkt. Dazu wird ein Theorieüberblick über gesellschaftliche Wirkungsanalyse erarbeitet und ausgewählte Instrumente der Unternehmenssteuerung vorgestellt. Daraufhin werden fünf Hypothesen gebildet, die in einer Einzelfallstudie anhand eines jungen Sozialunternehmens in Österreich überprüft werden. In diesem Praxisteil ist ein Vergleich hinsichtlich der Impact-Orientierung im untersuchten Sozialunternehmen zu jener, die in der Literatur dargestellt wird, zentral. Weiters wird die Frage untersucht, wie die in der Literatur angegebenen Managementinstrumente für Wirkungsorientierung in diesem Unternehmen angewendet werden und zu welchen Ergebnissen diese führen. Schließlich wird erforscht, ob Wirkungsziele und passende Managementinstrumente einen Beitrag zur Lösung des angenommenen Zielkonfliktes zwischen gesellschaftlichen und ökonomischen Zielen beitragen können. Die Ergebnisse und Erkenntnisse der Einzelfallstudie werden abschließend im Gespräch mit einer übergeordneten Einrichtung einer ersten Verifikation unterzogen. Diese Arbeit kommt zum Schluss, dass Impact-Orientierung eine sehr langfristige Ausrichtung der Unternehmenssteuerung bedarf. Die Impact-Ziele und Indikatoren müssen sich in den gewählten Instrumenten wiederfinden. Nur dadurch ist sichergestellt, dass Unternehmenssteuerung und Impact-Orientierung stringent zusammenwirken. Bei aller Unsicherheit zum WIE der Umsetzung, hat die Impact-Orientierung zentrale Auswirkungen auf die Unternehmenssteuerung. N2 - Changes in the social value system, the penetration of the commercial private sector into areas that have been covered by non-profit organizations for a long time, and the financial crisis of public budgets are considered to be major causes for the diverse and controversial discussion of the Social Impact Orientation in the German-speaking world. This thesis focuses on the question of how social impact orientation affects instruments of corporate management. For this purpose, a theoretical overview of social impact analysis is developed, and selected instruments of corporate management are presented. Afterwards, five hypotheses are formed, which are tested in a single case study based on a young social enterprise in Austria. In this practical part of the research, a comparison regarding the impact orientation in the social enterprise under study with what is presented in the literature is pivotal. Furthermore, the question of how the management instruments for impact orientation given in the literature are applied in this company and to which results they lead is examined. Finally, it is investigated whether impact objectives and appropriate management instruments can contribute to solving the assumed conflict of objectives between social and economic objectives. The results and findings of the individual case study are then subjected to an initial verification in discussions with a superordinate institution. This work concludes that impact orientation requires a very long-term approach to corporate management. The impact targets and indicators must be reflected in the chosen tools. This is the only way to ensure that corporate management and impact orientation work together stringently. Despite all the uncertainty about HOW it is implemented, the impact orientation has central effects on corporate management. T2 - The effect of social impact orientation on instruments of corporate management : a single case study of a social enterprise in Austria KW - Social Impact-Orientierung KW - Gesellschaftliche Wirkungsanalyse KW - Wirkungsziele KW - Instrumente der Unternehmenssteuerung Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3676 ER - TY - THES A1 - Michler, Johannes T1 - Auf dem Weg in eine bargeldlose Gesellschaft? BT - ein Ländervergleich zwischen Österreich und Schweden N2 - In vielen Ländern gibt es eine stetige Verschiebung von Bargeld zu Kartenzahlung. Dieser Umstand könnte darauf hinweisen, dass Bargeld irgendwann verschwinden wird. Der Bargeldumlauf ist in den meisten Ländern, einschließlich Österreich, jedoch seit Jahrzehnten stabil oder stark gestiegen. Im Gegensatz dazu gilt Schweden als eine Vorreiternation auf dem Weg in die bargeldlose Gesellschaft. In der vorliegenden Masterthesis werden die Unterschiede zwischen Österreich und Schweden erläutert, indem die Zahlungsmärkte als auch das Potenzial der Länder aufgezeigt werden. Weiters werden die möglichen Einflüsse wie Bargeldversorgung, Technologie und Infrastruktur, Regulierungen und das unterschiedliche Zahlungsverhalten und die Mentalität der Konsumenten untersucht. Daraus werden dann Schlussfolgerungen gezogen, wohin sich die verschiedenen Zahlungsmärkte in Zukunft bewegen werden. Die Daten basieren auf Sekundärdaten, die aus Büchern, Zeitschriften, verschiedenen Forschungsarbeiten und Onlinequellen stammen. Egal, welchen Standpunkt Sie in Bezug auf die Zukunft des Bargeldes einnehmen, soll diese Masterthesis einen besseren Einblick über die Transformation unserer Volkswirtschaft und den Mechanismus von unbaren Zahlungen geben. N2 - In many countries, there is a steady shift from cash to card payments, which might suggest that cash will eventually disappear. However, cash in circulation in most countries, including Austria, has remained stable or increased significantly for decades. In contrast, Sweden is considered a pioneering nation on the way to a cashless society. This master thesis explains the differences between Austria and Sweden by showing the payment markets as well as the potential of the countries. It is focusing on possible influences such as cash supply, technology and infrastructure, regulations and the different payment behavior and the mentality of consumers. From this, conclusions are drawn where the different payments markets are heading in the future. The data is based on secondary data taken from various books, journals, research papers and online sources. Regardless of which viewpoint you have regarding the future of cash, this master thesis aims to provide a better insight into the transformation of our economy and the mechanics of non-cash payments. T2 - On the way to a cashless society? : a country comparison between Austria and Sweden Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3701 ER - TY - THES A1 - Töfferl, Simon T1 - Auswirkungen der DSGVO auf das Vertriebscontrolling eines Software-as-a-Service Geschäftsmodells BT - eine systematische Literaturanalyse inklusive Anwendungsbeispiel der Geosystems Division der Hexagon AB N2 - Diese Arbeit untersucht die Auswirkungen eines SaaS Geschäftsmodells auf das Vertriebscontrolling. Dazu werden mittels Literatur die Kennzahlen und Instrumente des klassischen Vertriebscontrollings besprochen. Ein SaaS Geschäftsmodell hat spezifische Charakteristika, Herausforderungen und Erfolgsfaktoren, welche im Anschluss eingeführt werden. Diese beeinflussen das Vertriebscontrolling eines SaaS Geschäftsmodells. Die DSGVO schränkt das Vertriebscontrolling dabei, in der Nutzung von personenbezogenen Daten, ein. Diese Arbeit zeigt, dass die Grundelemente des Vertriebscontrollings bestehen bleiben, jedoch andere Kennzahlen verwendet werden müssen. Zusätzlich kommen neue Aufgaben auf das Vertriebscontrolling zu. Abschließend werden Handlungsempfehlungen für das Vertriebscontrolling eines SaaS Geschäftsmodells entwickelt. Mittels einer systematischen Literaturrecherche werden diese Handlungsempfehlungen bestätigt. N2 - This thesis researches the influence of a SaaS business model on the sales management accounting. Using literature, the key figures and instruments of the classical sales management accounting get introduced. A SaaS business model has its own characteristics, challenges and success factors, which get introduced. These result into changes in the sales management accounting of a SaaS business model. The GDPR restricts the usage of personal data in management accounting. This thesis argues that the fundamental elements of management accounting stay the same, however different key figures must be used to analyze a SaaS business model. Additional tasks are added to the responsibility of the sales management accounting. This thesis develops guidance on doing management accounting in a SaaS business model. Using a systematic literature research, the developed guidance is confirmed. T2 - Influence of the GDPR on the sales management accounting in software-as-a-service business models Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3671 ER - TY - THES A1 - Linder, Madeleine T1 - Realtime-Controlling in der Produktion BT - Analyse von Chancen und Herausforderungen für das Produktionscontrolling in Echtzeit N2 - Durch die Verfügbarkeit von Echtzeitinformationen wird das Produktionscontrolling und die Unternehmensorganisation zunehmend vor neue Herausforderungen gestellt. Die dynamische Unternehmensumwelt, die globale Orientierung der Wertschöpfung und neue Technologien führen zu einer Änderung des Fokus der Unternehmenssteuerung. Durch den Markt geforderte Informationen aus der Wertschöpfung sind durch neue Technologien transparent, prozessübergreifend und in großen Mengen verfügbar. Für die Entscheidungsstellen der Unternehmen müssen diese Informationen zusammengestellt und aufbereitet verfügbar sein. Diese neue Aufgabe fällt dem Controlling zu, wodurch es in den Fokus der Entscheidungsfindung gerät. Das Ziel der Masterthesis ist es mögliche Auswirkungen und Herausforderungen der Echtzeitinformationen auf das Controlling, insbesondere auf das Produktionscontrolling, herauszuarbeiten. Dazu wird folgende Forschungsfrage gestellt: Welche Herausforderungen sowie Chancen und Risiken ergeben sich durch die Verfügbarkeit von Echtzeitinformationen auf das Produktionscontrolling der Zukunft? Zur Beantwortung der Forschungsfrage und der damit verbundenen Unterfragen wird eine systematische Literaturanalyse von internationalen Quellen aus den Jahren 2012 bis 2020 durchgeführt. Im Ergebnis verändert sich das Aufgabengebiet des Produktionscontrollers weitestgehend. Zudem wird die Wichtigkeit des Controllings durch die Präsenz der Echtzeitinformationen nicht abnehmen, sondern einen neuen Stellenwert in der Unternehmenssteuerung bekommen. Das Controlling als Businesspartner der Unternehmenssteuerung bekommt eine neue Stelle auf Augenhöhe des Managements. N2 - The management accounting and the corporate organization increasingly face challenges through the availability of real-time information. The dynamic corporate environment, global orientation of production and new technologies lead to a change of focus in corporate management. New technologies provide large quantities of transparent information across operations about the value creation required by the market. This available information has to be structured and processed for the management of companies. The controlling department takes this new task getting in the focus of management. The goal of the master thesis is to work out possible effects and challenges of real-time information for the controlling department, in particular for the production controlling. On this basis, the following research question is asked: What challenges, opportunities and risks arise from the availability of real-time information on future production controlling? To answer the research question as well as related sub-questions, a systematic literature analysis of international sources published from 2012 to 2020 was conducted. As a result, the responsibilities and tasks of the production controlling experience a wide change. Furthermore, the importance of the controlling department will not decrease due to the presence of real-time information but will take on a new role within the corporate management. The controlling department as a business partner in corporate management is given a new position at an equal level to the management. KW - Echtzeit KW - Produktionscontrolling KW - Digitalisierung Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3727 ER - TY - THES A1 - Bammert, Urs T1 - Analyse des Earnings Managements der M-DAX Unternehmen BT - eine empirische Untersuchung N2 - Das Management eines Unternehmens kann Mithilfe von bilanzpolitischen Maßnahmen bewusst Einfluss auf das Unternehmensergebnis nehmen. Durch Ausnutzung von Ermessenspielräumen bei der Bildung und Auflösung von Rückstellungen können stille Reserven gebildet und in späteren Perioden wieder aufgelöst werden. In dieser Masterarbeit wurde untersucht ob die Unternehmen des M-DAX mithilfe der Big-Bath-Accounting-Methode oder der Income-Smoothing-Methode bewusst Einfluss auf das Jahresergebnis genommen haben. Hierfür wurden die Geschäftsberichte der Zielgruppe im Zeitraum von 2009 – 2018 empirisch untersucht. Um die Gültigkeit der Hypothesen zu überprüfen wurde das ausgewiesene EBIT mit einem bereinigten EBIT verglichen. Für die Ermittlung des bereinigten EBITs wurden die tatsächlichen Rückstellungsbildungen bzw. Rückstellungsauflösungen durch die über den Betrachtungszeitraum durchschnittlichen Rückstellungsbildung bzw. Rückstellungsauflösung ersetzt. Die Ergebnisse der empirischen Untersuchung haben gezeigt, dass die Unternehmen der Zielgruppe Mithilfe von Rückstellungen großen Einfluss auf das EBIT nehmen können. Weiter konnte belegt werden, dass die meisten Unternehmen bei der Rückstellungsbewertung grundsätzlich vorsichtig agieren und höhere Beträge in Rückstellungen bilanzieren. N2 - The management of a company can consciously influence the company's results with the help of balance sheet policy measures. By making use of a discretionary scope in the formation and release of provisions, hidden reserves can be formed and released again in later periods. This master's thesis investigated whether the companies of the M-DAX have consciously influenced the annual result by using the Big-Bath-Accounting-Method or the Income-Smoothing-Method. For this purpose, the annual reports of the target group in the period 2009 - 2018 were empirically studied. To test the validity of the hypotheses, the reported EBIT was compared with an adjusted EBIT. In order to determine the adjusted EBIT, the actual formation or reversal of provisions was replaced by the average formation or reversal of provisions over the analyzed period under review. The results of the empirical study have shown that the companies in the target group can greatly influence the EBIT with the help of provisions. Furthermore, it showed that most companies are generally cautious in the valuation of provisions and report higher amounts in provisions. KW - Bilanzpolitik KW - Rückstellungen Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3682 ER - TY - THES A1 - Aberer, Michael T1 - Marktreaktion und Relevanz von Analystenempfehlungen in verschiedenen konjunkturellen Entwicklungsphasen BT - eine empirische Untersuchung N2 - Die vorliegende Masterarbeit enthält neue Erkenntnisse in Bezug auf die Frage, ob die Änderung einer Analystenempfehlung für Aktien neue Informationen enthält und ein Anleger eine abnormale Rendite erzielen kann. Darüber hinaus wird untersucht, ob in Phasen des konjunkturellen Abschwungs eine höhere abnormale Rendite im Vergleich zu einem konjunkturellen Aufschwung ausgewiesen wird. Die Ergebnisse zeigen, dass Aktienkurse signifikant positiv auf Kaufempfehlungen und signifikant negativ auf Verkaufsempfehlungen reagieren. Zusätzlich wird belegt, dass eine höhere und zeitlich längere Reaktion auf eine Verkaufsempfehlung gegenüber einer Kaufempfehlung stattfindet. Es wird außerdem festgestellt, dass auch bei isolierter Betrachtung der Konjunkturzyklen (Aufschwung und Abschwung) eine abnormale Rendite erzielt wird. Zudem verzeichnen negative Veränderungen der Analystenempfehlungen eine höhere abnormale Rendite als jene bei positiven Veränderungen. N2 - The master thesis provides evidence to the question whether the change of an analyst recommendations for stocks contain new information and whether an investor can achieve an abnormal return. Furthermore, it is examined whether a higher abnormal return is shown in phases of economic downturn compared to an economic upswing. The results show that share prices react significantly positive to buy recommendations and significantly negative to sell recommendations. In addition, it is shown that there is a higher and longer reaction to a sell recommendation compared to a buy recommendation. Even by considering the economic cycles (upswing and downturn) an abnormal return is achieved. In addition, negative changes in the analyst recommendations generate a higher abnormal return than those with positive changes. T2 - Market reaction and relevance of analyst recommendations in different economic development phases Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3728 ER - TY - THES A1 - Barkovskaia, Larisa T1 - Austrian labor market attractiveness for highly qualified professionals in information technology occupations N2 - The boom of information technology development created high demand for skilled labour force in IT occupations. IT professionals install, test, build, repair or maintain hardware and software and can do the job from any location in the world. Demand for the workforce significantly outstrips the global supply. In a situation of staff shortage employers have to compete on local and global labour markets. The ability of a firm to attract and retain the best talent would become a source of its sustainable competitive advantage. Aim of the study is to understand what influences perception of employment attractiveness by IT professionals the most. This study intends to expend the existing knowledge about employees´ needs and “psychological contract” concept. The research was conducted with the participation of 4 IT and 4 HR English-speaking experts who live and work in Austria. In the study the grounded theory approach and the descriptive qualitative methods were applied. The research findings explain which factors influence the decision of IT professionals to join, stay or leave an employer. The results are discussed in relation to talent attraction and retention practices of Austrian employers. KW - IT KW - Austrian labour market Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3753 ER - TY - THES A1 - Richter, Florian T1 - Automatisierte Beurteilung und Selektion kultivierter Embryos in der assistierten Reproduktionsmedizin N2 - Die morphologische Beurteilung menschlicher Embryos ist ein zeitaufwändiger Prozess in der assistierten Reproduktionsmedizin. Etwa fünf Tage entwickeln sich die Embryos bei einer IVF-Behandlung außerhalb des menschlichen Körpers, bevor Embryologinnen und Embryologen die Entscheidung über die zu transferierenden – also die für die Einleitung einer künstlich herbeigeführten Schwangerschaft zu verwendenden – Embryos anhand unterschiedlicher Bewertungskriterien treffen. Im Anschluss an eine Einführung in die Embryologie werden in dieser Arbeit mögliche Methoden zur automatisierten Embryoselektion besprochen, implementiert, miteinander verknüpft und abschließend evaluiert. Die Arbeit beschränkt sich mit dem EmbryoScope auf einen Zeitrafferinkubator, welcher in den IVF Zentren Prof. Zech in Bregenz in den letzten Jahren viele Millionen Bilder tausender befruchteter Eizellen und den daraus entstehenden Embryos aufgenommen hat. Dieses Gerät diente als Datenquelle zur Unterstützung bei der Entwicklung des Analysetools. Das entstandene Softwareprodukt wurde so programmiert, dass gegebenen Daten vorverarbeitet und unter Anwendung von Bildmanipulationsverfahren und komplexer neuronaler Netze analysiert werden können. Das Ergebnis ist eine Software zur Erkennung und Bewertung unterschiedlicher Parameter der Embryoentwicklung, um daraus Vorschläge für die Selektion der zu transferierenden Embryos generieren und übersichtlich präsentieren zu können. Zur Evaluierung des Systems konnten drei Embryologinnen und Embryologen aus drei IVF Kliniken unterschiedlicher europäischer Länder gewonnen werden, um anhand einer eigens entwickelten Annotationssoftware Vergleichsdaten zu generieren. Als Endergebnis der Arbeit wurde die Einheitlichkeit dieser erhaltenen Annotationsdaten mit den errechneten Vorschläge anhand unterschiedlicher Kriterien berechnet. Die Transferierbarkeit eines einzelnen Embryos konnte im Vergleich zur Entscheidung des Laborpersonals in 73 % der Fälle korrekt erkannt werden. Bezogen auf eine gesamte IVF Behandlung konnte bei den tatsächlich zu transferierenden Embryos eine vollumfängliche Einheitlichkeit von 26 % mit den Embryologinnen und Embryologen erreicht werden. Embryos, welche von dem entstandenen Analysetool als transferierbar erkannt und unter Beachtung weiterer vorhandener Embryos für die weitere Behandlung vorgeschlagen wurden, sind in 63 % der Fälle für einen Transfer geeignet. Das entstandene Vorschlagsystem ist als Proof of Concept zu verstehen, welches in späteren Arbeiten durch tiefgreifendere Analysen erweitert werden kann. Ein Einsatz des Systems ist aufgrund der geringen Analysesicherheit, sowie technischen und rechtlichen Einschränkungen zum Abschluss der vorliegenden Arbeit nicht vorgesehen. N2 - The morphological assessment of human embryos is a time-consuming process in assisted reproductive medicine. In IVF2 treatment, the embryos develop outside the human body for about five days before embryologists select the ones to be transferred - i.e. the ones used to induce an artificially caused pregnancy - based on different assessment criteria. Following an introduction to embryology, this thesis discusses, implements, links, and finally evaluates possible methods for automated embryo selection. With the EmbryoScope, the work is limited to a time-lapse incubator, which has recorded many millions of images of thousands of fertilized oocytes in the IVF Zentren Prof. Zech in Bregenz in recent years. This device served as a data source to support the development of the analysis tool. The resulting software product can preprocess the given data and analyze them using image manipulation techniques and complex neural networks. The result is a software for the recognition and evaluation of different parameters of embryo development, to be able to generate and clearly present suggestions for the selection of the embryos to be transferred. For the evaluation of the system, three embryologists from three IVF clinics in different European countries could be recruited to generate comparative data using a specially developed annotation software. As a result of the work, the uniformity of these obtained annotation data was compared with the suggestions calculated by the developed analysis software. The transferability of a single embryo could be correctly detected in 73 % of cases compared to the decision of the laboratory staff. In relation to an overall IVF treatment, 26 % of the oocytes to be transferred were consistent with the embryologists. Embryos that were identified as transferable by the resulting analysis tool and proposed for further treatment, considering other existing embryos, are suitable for transfer in 63 % of cases. The resulting suggestion system is to be understood as a proof of concept, which can be extended in subsequent developmental steps by further, more in-depth analyses. A productive use of the system is not planned at the end of the present work due to the low analysis reliability and technical as well as legal restrictions. T2 - Automated assessment and selection of cultured embryos in assisted reproductive medicine KW - Machine-learning KW - Maschinelles Lernen KW - Embryologie KW - IVF KW - Automatisierung Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3680 ER - TY - THES A1 - Rhomberg, Helmut T1 - Teachen von Industrierobotern mittels Gestenerkennung N2 - Das Teach Pendant wird dazu genutzt um Industrierobotern Zielposen beizubringen, damit diese die Zielposen daraufhin autonom anfahren können. Durch den auf dem Teach Pendant zur Eingabe verbauten Joystick oder die 3D-Maus ist es möglich mit geringem Rechenaufwand Bewegungen und somit Zielposen präzise vorzugeben. Durch den rasanten Anstieg der Rechenkapazität und den stetigen Erfolgen bei der Erforschung von künstlichen neuronalen Netzwerken sind heutzutage Gestenerkennungssysteme in das Blickfeld der Forschung gelangt. Gestenerkennungssysteme versprechen intuitive und leicht zu erlernende Bedienungskonzepte. Durch den Einsatz von Gesten kann zudem auf ein zusätzliches Gerät in den Händen verzichtet werden, wodurch das Nutzererlebnis gesteigert werden kann. Dies kann bei schweren Eingabgeräten nicht nur die Arme sondern auch die Hände vor Ermüdungserscheinungen schonen. Das Ziel dieser Arbeit soll es daher darstellen, ein Gestenerkennungssystem mit und ohne ROS-Anbindung zu erstellen, testen und analysieren. Die Gesteninformationen werden von einer Tiefenkamera vom Typ Azure Kinect bereitgestellt. Als Industrieroboter wird hierbei der "WidowX 200"-Lernroboter eingesetzt, da dieser aufgrund seiner kleinen Bauform einfach und effizient zum Testen von neuen Funktionalitäten eingesetzt werden kann. Die Tiefenkamera- und Roboter-Komponente sollen austauschbar bleiben. Die zu entwickelnden Gesten sollen vor allem hohe Ergonomie bereitstellen und vor unbeabsichtigter Durchführung gesichert sein. Die Genauigkeit der Gestenerkennung wird analysiert, um die Zuverlässigkeit der ausgewählten Gesten zu evaluieren. Die Genauigkeit der erreichten Zielposen des "WidowX 200"-Lernroboters wird analysiert und Latenztests werden durchgeführt um das Gestensystem als Gesamtes bewerten zu können. N2 - The Teach Pendant is used to teach target poses to industrial robots, so that they can approach the target poses autonomously. The joystick or 3D mouse installed on the teach pendant for input makes it possible to specify movements and thus target poses precisely with little computing effort. Due to the rapid increase in computing capacity and the constant success in the research of artificial neural networks, gesture recognition systems have become the focus of research today. Gesture recognition systems promise intuitive and easy to learn operating concepts. The use of gestures also makes it possible to do without an additional device in the hands, thus enhancing the user experience. In the case of heavy input devices, this can protect not only the arms but also the hands from signs of fatigue. The goal of this thesis is therefore to create, test and analyze a gesture recognition system with and without ROS connection. The gesture information is provided by a depth camera of the Azure Kinect type. The "WidowX 200" learning robot is used as the industrial robot for this purpose, since its small design allows it to be used simply and efficiently for testing new functionalities. The depth camera and robot components are to remain interchangeable. The gestures to be developed should above all provide high ergonomics and be protected against unintentional execution. The accuracy of gesture recognition will be analyzed to evaluate the reliability of the selected gestures. The accuracy of the achieved target poses of the "WidowX 200" learning robot will be analyzed and latency tests will be performed to evaluate the gesture system as a whole. T2 - Teaching of industrial robots using gesture recognition KW - Industrieroboter KW - Gestenerkennung KW - Teach-in KW - Tiefenkamera Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3666 ER - TY - THES A1 - Lorünser, Katharina T1 - Gesundheitsfördernde Maßnahmen in Vorarlberger Unternehmen und öffentlichen Einrichtungen BT - Nutzung von eingesetzten gesundheitsfördernden Maßnahmen durch Mitarbeitende N2 - Die Bedeutung der betrieblichen Gesundheitsförderung (BGF) ist in den letzten Jahren aufgrund des Wandels der Arbeitswelt durch Technologien, der Globalisierung sowie des demografischen Wandels stark gestiegen. Gesunde und motivierte Mitarbeitende sind essenziell für ein erfolgreiches Unternehmen. Deshalb rückt der Erhalt der Gesundheit der Mitarbeitenden und die Steigerung des Wohlbefindens am Arbeitsplatz für Firmen immer mehr in den Vordergrund. Zahlreiche Betriebe sind somit zunehmend gezwungen, sich mit verschiedenen gesundheitsfördernden Interventionen zu beschäftigen. Die vorliegende Studie beschäftigt sich mit der Frage, welche gesundheitsfördernden Maßnahmen in Vorarlberger Unternehmen und öffentlichen Einrichtungen genutzt werden. Daraus lässt sich ableiten, welche Maßnahmen vorrangig angeboten werden. Die theoretische Grundlage bildet eine Literaturrecherche. Insgesamt wurden 312 Vorarlberger Arbeitnehmende mit einem Durchschnittsalter von 33,79 Jahren mittels einem vollstandardisierten Fragebogen befragt. Als meist genutzte Interventionen stellten sich besonders die verhältnispräventiven Maßnahmen, wie flexible Arbeitszeitmodelle, ergonomische Bürostühle und regelmäßige Pausen, heraus. Der Wunsch nach zusätzlichen verhaltenspräventiven Maßnahmen (prägen den individuellen Lebensstil), wie bspw. gesunde Ernährungsangebote und Obstkörbe, spiegeln sich jedoch in den Ergebnissen wider. Generell lässt sich sagen, dass auch aufgrund der rechtlichen Vorgaben vermehrt Maßnahmen zur gesunden Gestaltung des Arbeitsverhältnisses, also verhältnispräventive Maßnahmen, angeboten und daher auch genutzt werden. N2 - The importance of the WHP has increased significantly in recent years due to the changes in the working world caused by technology, globalization and demographic changes. Healthy and motivated employees are essential for a successful company. That is why maintaining the health of employees and increasing well-being at work is becoming increasingly important for companies. Thus, numerous companies are increasingly forced to deal with various health-promoting interventions. This study deals with the question of which health-promoting measures are used in companies and public institutions in Vorarlberg. From this it can be deduced which measures are primarily offered. The theoretical basis is a literature research. A total of 312 Vorarlberg employees with an average age of 33.79 years were surveyed with a fully standardized questionnaire. The most frequently used interventions turned out to be especially the ratio-preventive measures, such as flexible working time models, ergonomic office chairs and regular breaks. However, the desire for additional behavioural preventive measures (shaping individual lifestyles), such as healthy nutritional offers and fruit baskets, is reflected in the results. In general, it can be said that due to legal requirements, measures for a healthy structuring of the employment relationship, i.e. relationship preventive measures, are increasingly being offered and therefore also used. T2 - Health-promoting measures in companies and public institutions in Vorarlberg : use of health-promoting measures used by employees Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3714 ER - TY - THES A1 - Riemer, Jasmin T1 - Erfolgsfaktoren umsetzbarer Entscheidungen im Projekt BT - mit induktiver Einsicht bei der Rhomberg Bahntechnik N2 - Die Forschungsfrage dieser Masterarbeit wird beantwortet, indem die Erfolgsfaktoren umsetzbarer Entscheidungen im Projekt herausgearbeitet und mittels Checkliste für die Projektleitung anwendbar werden. Die Checkliste unterstützt, dass das definierte Projektziel unter effizienter Ressourcennutzung erreicht wird, indem das Zustandekommen von Entscheidungen prozesshaft ausgestaltet wird. Die Checkliste baut auf einer managementorientierten Sicht der BWL auf und berücksichtigt die Erkenntnisse des aktuellen Sankt Galler Management-Modells mit seiner Aufgaben- und Praxisperspektive. Durch die Einsicht in die Rhomberg Bahntechnik GmbH soll dem/der Leser/in aufgezeigt werden, welche Rahmenbedingungen und Ziele ein Projekt hat und wie ein Projektmanagement in der Praxis gestaltet werden kann. Die wesentliche Erkenntnis ist, dass komplexe Entscheidungen nur von Menschen getroffen werden können. Die personale Existenzanalyse enthält anwendungsfähige Methoden, mit derer sich die Menschen zu umsetzbaren Entscheidungen führen können. Deshalb wird im Ausblick auf die personale Existenzanalyse kurz eingegangen. N2 - The research question of this master thesis is answered by working out the success factors of implementable decisions in the project and applying them to the project management using a checklist. The checklist supports that the defined project goal is achieved with efficient use of resources by structuring the process of making decisions. The checklist is based on a management-oriented view of business administration and takes into account the findings of the current Sankt Gallen management model with its task and practical perspective. By viewing Rhomberg Bahntechnik GmbH, the reader should be shown what framework conditions and goals a project has and how project management can be designed in practice. The key finding is that complex decisions can only be made by people. The personal existence analysis contains usable methods with which people can lead to implementable decisions. That is why the personal existence analysis is cured in the outlook. T2 - Success factors of implementable decisions in the project : with inductive insight at Rhomberg Bahntechnik KW - SGMM KW - Entscheidung KW - Systemtheorie Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3722 ER - TY - THES A1 - Zudrell, Bianca T1 - Prinzipien und Faktoren zur Bestimmung eines fairen Entgelts BT - aus der Sicht von unselbstständig Erwerbstätigen in Vorarlberg N2 - Lohngerechtigkeit ist ein Thema, mit dem jede Person im Laufe des Lebens mehrmals konfrontiert wird. Sehr häufig wird dieses Thema auch in der Öffentlichkeit debattiert, vor allem wenn es um die „Gender Pay Gap“ geht, also die Lohnlücke zwischen Mann und Frau. Das Ziel dieser Masterthesis ist es deshalb herauszufinden, welche Faktoren für die Bestimmung eines fairen Entgelts laut unselbstständig erwerbstätiger Personen in Vorarlberg berücksichtigt werden sollen. Dabei wird nicht nur auf die gängigen Faktoren Berufserfahrung und Ausbildung eingegangen, sondern eine Vielzahl an Faktoren berücksichtigt. Mit Hilfe eines Fragebogens wurde dann hauptsächlich die Meinung von Angestellten mit einem Durchschnittsalter von 32,4 Jahren erhoben. Dabei hat sich gezeigt, dass die bedeutendsten vier Faktoren Leistung, Berufserfahrung, Position (inklusive der damit verbundenen Aufgaben und Verantwortung) und Ausbildung sind. Am unbedeutendsten werden Geschlecht, Unternehmensgröße und Familienstand erachtet. Außerdem konnte belegt werden, dass sich das Lohngerechtigkeitsempfinden stark an den eigenen Lebensumständen orientiert. N2 - Fair wages area topic that faces everybody more than once in their professional career. Very often this topic is also discussed in publicity, especially when it comes to wage differences between women and men. Therefore, this master thesis aims to find out, which factors should be considered to define a fair payment from the viewpoint of employed people in Vorarlberg. It will not only consider the usual factors like professional experience and education, but more a variety of different factors. With the help of an online questionnaire, the opinion mainly of white-collar workers with an average age of 32.4 years have been analyzed. The research showed that the most important factors are performance, professional experience, position aligned with tasks and responsibilities as well as education. The least important criteria according to the analysis are gender, size of the organization and civil status. Moreover, it could be verified, that the perception of fair payment is strongly based on the own living conditions. T2 - Principles and factors for the definition of a fair payment : from the viewpoint of employed people in Vorarlberg KW - Lohn KW - Lohngerechtigkeit Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3760 ER - TY - THES A1 - Tschol, Christina T1 - Analyse von Methoden zur Bedrohungsidentifikation und Metriken zur Risikoanalyse von Prüf- und Messlösungen in kritischen Infrastrukturen N2 - Risikomanagement wird in einem sicheren Software-Entwicklungs-Lebenszyklus angewendet, um bei Produkten mögliche Risiken bereits in den frühen Entwicklungsphasen zu entdecken. Diese Arbeit ist aus Sicht eines Zulieferers für die elektrische Energiewirtschaft geschrieben. Das Ziel dieser Forschung ist es, bestehende Methoden zur Bedrohungsidentifikation und Metriken zur Risikoanalyse zu untersuchen. Dazu wurde die folgende Forschungsfrage gestellt: Welche Methoden zur Bedrohungsidentifikation und Metriken zur Risikoanalyse sollen verwendet werden, um im Produktentwicklungsprozess den Anforderungen an Unternehmen, die als Zulieferer für die elektrische Energiewirtschaft fungieren, zu entsprechen und potentielle Bedrohungen im Anfangsstadium eines Projektes zu identifizieren? Um diese Forschungsfrage zu beantworten, wurden Methoden zur Bedrohungsidentifikation (STRIDE, Angriffsbäume und Angriffsbibliotheken) und Metriken (aus CVSS, OWASP und Literatur entnommen) zur Risikoanalyse in die theoretische Wissensgrundlage aufgenommen, in Bezug auf den Kontext und die Anforderungen analysiert und ein Ergebnis hergeleitet. Die Analyse basiert auf dem Kontext und der definierten Anforderungen aus Standards und Normen, wie IEC 62443-4-1 (Anforderungen an den Lebenszyklus für eine sichere Produktentwicklung), spezielle Publikationen von dem National Institute of Standards and Technology 800-30 (Guide for Conducting Risk Assessments) und 800-82 (Guide to Industrial Control Systems Security). Zusätzlich wurden noch Empfehlungen von der UP KRITIS (Öffentlich-Private Partnerschaft zum Schutz kritischer Infrastrukturen) aufgenommen. Anhand der Analyse der Methoden zur Bedrohungsidentifikation wurde deduziert, dass aufgrund der Anforderungen keine konkreten Methoden empfohlen werden können. Basierend auf die Anforderungen an die Risikoanalyse konnten in dieser Arbeit die folgenden Schadensmetriken abgeleitet werden: Funktionale, lebensgefährliche oder -bedrohliche Auswirkungen, geschäftliche Auswirkungen, sowie Auswirkungen auf Daten und Informationsressourcen. N2 - Risk management is applied in a secure software development lifecycle to detect potential risks in products in the early stages of development. This thesis is written from the perspective of a supplier for the electrical power industry. The aim of this research is to analyse existing methods for threat identification and metrics for risk analysis. For this purpose, the following research question was asked: Which methods of threat identification and metrics for risk analysis should be used to meet the requirements of companies that act as suppliers for the electrical power industry in the product development process and to identify potential threats in the early stages of a project? In order to answer the research question, methods for threat identification (STRIDE, attack trees and attack libraries) and metrics (taken from CVSS, OWASP and literature) for risk analysis were incorporated into the theoretical knowledgebase, analysed in relation to the context and requirements, and afterwards a result was derived. The analysis is based on the context and the defined requirements from standards and norms, such as IEC 62443-4-1 (life cycle requirements for safe product development), special publications from the National Institute of Standards and Technology 800-30 (Guide for Conducting Risk Assessments) and 800-82 (Guide to Industrial Control Systems Security). In addition, recommendations have been included by the UP KRITIS (Public-Private Partnership for Critical Infrastructure Protection). Based on the analysis of the methods for threat identification, it was deduced that no concrete methods can be recommended due to the requirements. Based on the requirements for risk analysis, the following impact metrics could be derived in this thesis: Functional, life-threatening, business impacts as well as impacts on data and information resources. T2 - Analysis of threat identification methods and metrics for risk analysis of test and measurement solutions in critical infrastructures KW - Risikomanagement Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3663 ER - TY - THES A1 - Bilgin, Oktay T1 - Zentralisierte Aggregation von heterogenen Logdaten aus einem Industrieumfeld für anomalie-basierte Intrusion Detection Systeme N2 - Die Digitalisierung von Unternehmen und deren Produktionsanlagen bringen neue Bedrohungsformen mit sich, die zielorientierter ausgerichtet sind und mehrere Computersysteme gleichzeitig betreffen. Klassische Schutzmechanismen wie Firewalls, Anti-Viren-Systeme und IDS sind zumeist signatur- oder muster-basiert und können diese komplexen Bedrohungsformen nicht effizient erkennen. Die verwendeten Signaturen und Muster können durch Angreifer einfach umgangen werden. Darüber hinaus sind gezielte und komplexe Angriffe nur durch die Verknüpfung von Informationen mehrerer Computersysteme identifizierbar. In den letzten Jahren wurden daher verstärkt anomalie-basierte IDS entwickelt und eingesetzt, die anhand selbstlernender Algorithmen das normale Verhalten von mehreren miteinander vernetzten Computersystemen erlernen und Abweichungen zum normalen Verhalten identifizieren. Hierzu verwenden die Algorithmen Log- und Monitoringdaten der Anwendungsschicht von verschiedenen Computersystemen und Anwendungen. Der Zugriff auf die Logdaten zur weiteren Analyse ist jedoch kompliziert, weil sie nicht an einer zentralen Stelle zusammenlaufen und es keine allgemein anerkannten Standards für die Erzeugung und Übertragung von Logdaten existieren. Infolgedessen wird in dieser Arbeit ein zentrales Log-Management-System in eine Produktionsumgebung eingeführt, die verschiedene IT-Komponenten und Komponenten einer realen Güterproduktion beinhaltet. Zudem werden Logdaten verschiedener heterogener Datenquellen auf diesem System zentral aggregiert. Neben der Einführung eines Standards für die Struktur und Übertragung der Logdaten von den einzelnen Datenquellen auf das Log-Management-System, werden Logdaten auf ihre Relevanz hinsichtlich der Erkennung von Anomalien und der Abbildung des Systemverhaltens analysiert. Diese Arbeit beinhaltet zudem fortgeschrittene Bedrohungsszenarien, die für die Evaluation der IDS verwendet werden können und stellt somit eine Grundlage für eine zukünftige Analyse der Logdaten durch IDS dar. N2 - The digitization of companies and their production facilities introduces new types of threats that are more sophisticated, tailored towards targets and affect multiple computer systems at the same time. Traditional protection mechanisms, such as firewalls, anti-virus software and intrusion detection systems apply a kind of black-list approach, where they consider only actions and behaviour that match well-known attack patterns and signatures of known malware or malicious behaviour. These traditional approaches can be easily bypassed with customized malware. Additionally, sophisticated and specifically targeted cyber-attacks can only be identified by aggregating information from several computer systems. In recent years, anomaly-based intrusion detection systems have therefore been increasingly developed and used, which try to establish a baseline of system behaviour of several interconnected computer systems using self-learning algorithms and try to identify deviations from this baseline. For this purpose, the algorithms use log and monitoring data from the application layer of various computer systems and applications. However, accessing this information for further analysis is often complicated. Usually, log data is not aggregated in one place and there exists no common standard for the appearance and transportation of log data. As a result, the thesis introduces a central log management system into a real manufacturing environment. Also, log data from various heterogeneous data sources is centrally aggregated on this system using a standard for the structure and transportation of log data. Furthermore, the available log data is analyzed for its relevance to detect anomalies and capture the computer system’s normal behaviour. The thesis also includes advanced threat scenarios that can be used to evaluate intrusion detection systems. This thesis forms the basis for future analysis of log data by intrusion detection systems. T2 - Centralized aggregation of heterogeneous log data from a manufacturing environment for anomaly-based intrusion detection systems Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3744 ER - TY - THES A1 - Mathis, Daniel T1 - Dynamische Contentzuweisung mit erweiterten Daten aus einem Content Management System durch eine Kombination von Langzeit- und Session-Profil mit einem hybriden Empfehlungssystem N2 - In dieser Arbeit wird eine Evaluation zwischen verschiedenen implementierten Ansätzen eines Empfehlungssystems auf der Basis eines realen Datensatzes durchgeführt. Der Datensatz beinhaltet das Navigationsverhalten von Besuchern einer Website über Kochrezepte. Während der Vorverarbeitung wird der Datensatz mit zusätzlichen Metainformationen für jedes besuchte Rezept aus dem Content Management System der Webseite angereichert. Die implementierten Empfehlungssysteme verwenden sowohl den Content Based Filtering als auch den Collaborative Filtering Ansatz. Zusätzlich werden beide Ansätze kombiniert und in einem hybriden Empfehlungssystem eingesetzt. Darüber hinaus werden für jede Person im Datensatz zwei individuelle Profile erstellt. Dabei handelt es sich um ein kurzlebiges Session-Profil und ein permanentes Langzeit-Profil. Mit jedem Besuch eines Rezeptes werden beide Profile dynamisch angepasst, so dass sich die individuellen Präferenzen der Personen jederzeit in den Profilen widerspiegeln. Für die Evaluation wird ein eigener Algorithmus angewendet, welcher es erlaubt einen Vergleich zwischen den implementierten Empfehlungssystemen vorzunehmen. Die Besonderheit an dem Evaluationsalgorithmus ist, dass dieser lediglich die besuchten Items und deren Beschreibung für den Vergleich benötigt. Es werden keine expliziten Bewertungen von den Webseitenbesuchern verwendet. In der Arbeit werden die Ergebnisse der unterschiedlichen Ansätze für ein Empfehlungssystem mit dem eigenen Evaluationsalgorithmus diskutiert und die Vor- bzw. Nachteile der jeweiligen Ansätze erläutert. Bei der Analyse stellt sich heraus, dass für den in dieser Arbeit verwendete Datensatz ein hybrides Empfehlungssystem, welches sowohl das Session-Profil als auch das Langzeit-Profil kombiniert, die besten Ergebnisse erzielt. Mit diesem System wird eine Übereinstimmungsgenauigkeit zwischen den vorgeschlagenen Rezepten und den tatsächlich besuchten Rezepten von knapp 36% erreicht. Die beiden Content Based Systeme, welche jeweils entweder das Session-Profil oder das Langzeit-Profil verwenden, erzielen eine Übereinstimmungsgenauigkeit von ca 30% bzw. 20%. Die Algorithmen mit dem Collaborative Filtering Ansatz erreichen bei dem verwendeten Datensatz nur eine Übereinstimmungsgenauigkeit von ca. 15% bzw. 13,5%. Als Referenzmodell wird ein Empfehlungssystem verwendet, das nach dem Zufallsprinzip Rezepte vorschlägt, wodurch eine Übereinstimmungsgenauigkeit von etwa 6% erreicht wird. N2 - In this thesis, an evaluation between different implemented approaches of a recommendation system is done based on a real data set. The data set contains the navigation behaviour of visitors of a website about recipes. During preprocessing, the data set is enriched with additional meta information for each visited recipe from the website’s content management system. The implemented recommendation systems uses the Content Based Filtering as well as the Collaborative Filtering approach. Additionally, both approaches are combined and used in a hybrid recommendation system. Furthermore, two individual profiles are created for each person in the data set. These are a short-lived session profile and a permanent long-term profile. Each time a person visits a recipe, both profiles are dynamically adjusted so that the individual preferences of the persons are always reflected in the profiles. For the evaluation an individual algorithm is used, which allows a comparison between the implemented recommendation systems. The special feature of the evaluation algorithm is that it only needs the visited items and their description for the comparison. No explicit ratings from the website visitors are used. In this thesis the results of the different approaches for a recommendation system with the own evaluation algorithm are discussed and the pros and cons of the different approaches are explained. The analysis shows that a hybrid recommendation system, which combines both the session-profile and the long-term profile, achieves the best results for the data set used in this thesis. Using this system, an accuracy of similarity between the proposed recipes and the actually visited recipes of 35% could be achieved. The two content-based systems, which use either the session profile or the long-term profile, achieved an accuracy of similarity of 30% and 20% respectively. The collaborative approaches could only achieve an accuracy of 15% and 13,5% for the data set used. A recommendation system is used as a reference model, which randomly suggests recipes, resulting in a similarity accuracy of about 6%. T2 - Dynamic content allocation with extended data from a content management system by combining long-term and session profiles with a hybrid recommendation system KW - Empfehlungssystem KW - Machine learning KW - Content based filtering KW - Collaborative filtering Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3746 ER - TY - THES A1 - Fleisch, Jan T1 - Interaktive Visualisierung von Verkaufsdatensätzen zur explorativen Erkenntnisgewinnung BT - interaktive Datenvisualisierung und visuelle Analysetechniken zur Mustererkennung in Verkaufsdatensätzen N2 - Moderne Darstellungen ermöglichen es, Daten nicht nur als statische Bilder, sondern auch als interaktive Visualisierungen darzustellen. Interaktive Darstellungen können im Kontext von Kundinnen- und Kundenanalysen eine einfache Weise sein, um Unterschiede in verschiedenen Kaufverhalten festzustellen und können so ein essenzielles Hilfsmittel für ein Unternehmen sein. Das Hauptziel dieser Arbeit ist es, anhand eines beispielhaften Verkaufsdatensatzes die Möglichkeiten der Datenexploration und Informationsbeschaffung durch interaktive Visualisierungen aufzuzeigen, sodass Rückschlüsse auf das Kaufverhalten verschiedener Gruppen gezogen werden können. Auf der Grundlage einer umfassenden Literaturrecherche in den Bereichen der Daten- und Informationsvisualisierung wurde eine Problemdefinition und eine Anforderungsanalyse für die Verkaufsdaten ausgearbeitet. Anonymisierte Verkaufsdaten dienten als Ausgangspunkt für die Datenvorverarbeitung. Diese wurden bereinigt und die gewünschten Informationen aus der Anforderungsanalyse wurden zur weiteren Transformation selektiert. Aufgrund der hohen Dimensionalität der selektierten Daten, wurde bei der Transformation der Dimensionsreduktions Algorithmus “Uniform Manifold Approximation and Projection” (UMAP) verwendet, um die Dimensionen der Daten zur Visualisierung zu reduzieren. Aufbauend auf diesen Schritten wurde ein Prototyp als Webanwendung erstellt, der den Anforderungen der Datenexploration und Informationsgewinnung gerecht wird. Der resultierende Prototyp kombiniert die achsenbasierten Visualisierungsmethoden der Streudiagramme und Parallelen Koordinaten mit der pixelorientierten Visualisierungsmethode der Heatmap. Diese Darstellungen wurden zusätzlich mit Interaktionsmöglichkeiten erweitert, um eine kollaborative Filterung von ähnlichen Konsumentinnen und Konsumenten auf verschiedenen Warengruppenebenen zu ermöglichen. Abgeschlossen wurde die Arbeit mit einer Evaluation des Prototypen und dessen Qualität zur Exploration. Die Auswertung wurde mit Benutzerinnen und Benutzern absolviert, die einen Versuchsablauf durcharbeiteten und dabei ihre Erkenntnisse in einem Fragebogen dokumentierten. Durch das Ausführen ließen sich Gruppierungen von Kundinnen und Kunden feststellen und diese konnten auf Richtigkeit in Bezug auf das Einkaufsverhalten validiert werden. Die hierarchische Verbindung der Warengruppenebenen und das Erkennen von Mustern in allen drei Warengruppenebenen konnte nicht als erfolgreich bewertet werden. Es wurde jedoch ein Potenzial zur weiteren visuellen Analyse von Konsumentinnen und Konsumenten anhand deren Einkaufsverhalten festgestellt und weitere Anforderungen zur Weiterentwicklung wurden festgehalten. N2 - Modern data visualizations make it possible to present data not only as static images, but also as interactive visualizations. In the context of customer analysis, interactive data visualizations can be an easy way to identify different buying behaviors of customer groups and can be an essential tool for a company. The main goal of this thesis is to show the possibilities of data exploration and information retrieval through interactive visualizations on the basis of a sample sales data set, so that conclusions about the buying behavior of different groups can be drawn. Based on a comprehensive literature research in the areas of data and information visualization, a problem definition and requirement analysis for the sales data were elaborated. Anonymised sales data served as a starting point for data pre-processing. These sales data were cleaned up and the desired information from the requirement analysis was selected for further transformation. Due to the high dimensionality of the selected data, the “Uniform Manifold Approximation and Projection” (UMAP) algorithm was used in the transformation process to reduce the dimensions of the data for visualization. Building on these steps, a prototype was created as a web application that meets the requirements of data exploration and information retrieval. The resulting prototype combines the axis-based visualization methods of scatter plots and parallel coordinates with the pixel-oriented visualization method of the heatmap. Furthermore, these visualizations were extended with additional interaction possibilities to enable collaborative filtering of similar consumers on different product group levels. The work was concluded with an evaluation of the prototype and its quality for exploration. The evaluation was made with users who worked through a experimental procedure and recorded their findings in a questionnaire. By executing the tests, groups of customers could be identified and these could be validated for accuracy with regard to their purchasing behavior. The hierarchical connection of the product group levels and the recognition of patterns in all three product group levels could not be evaluated as successful. However, a potential for further visual analysis of customers based on their purchasing behavior was identified and additional requirements for further development were identified. T2 - Interactive visualization of sales data sets for explorative knowledge discovery KW - Datenvisualisierung KW - Verkaufsdatensätze KW - Datenexploration KW - Visualisierungsmethoden Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3740 ER - TY - THES A1 - Hutter, David T1 - Robuste und ressourcenschonende kooperative Exploration und Kartierung mit homogenen autonomen Roboterteams N2 - In dieser Arbeit sollen Möglichkeiten untersucht werden, um eine möglichst robuste und ressourcenschonende Methode für homogene autonome Roboterteams um eine gemeinsame Exploration und Kartierung einer unbekannten Umgebung durchzuführen. Zu diesem Zweck soll eine koordinierte Exploration durchgeführt werden, durch die die zeitliche Effizienz des Roboterteams gesteigert werden kann. Dadurch kann unter geringerem Aufwand und in weniger Zeit eine globale Karte einer unbekannten Umgebung erstellt werden, mit der alle beteiligten Roboter für zukünftige Aufträge arbeiten können. Um dies zu erreichen wurden verschiedene Map-Merging Methoden untersucht, von denen eine auf Feature Detection basierende Verfahren für eine verteilte, robuste und ressourcenschonende Vorgehensweise ausgewählt wurde. Nachdem zwei oder mehr Karten erfolgreich fusioniert werden, kann eine koordinierte Exploration mit den Robotern, die mit der geteilten Karte arbeiten können durchgeführt werden. Für die gemeinsame Exploration werden auf dem implementierten Kartenserver nach allen Frontiers gesucht, die in der Karte vorhanden sind. Diese werden gemeinsam mit den derzeitigen Explorationszielen der anderen Roboter kombiniert und dem Roboter, der gerade versucht ein neues Explorationsziel zu wählen mitgeteilt. Dadurch können alle Roboter selbständig und unabhängig voneinander mit den Informationen der anderen Roboter arbeiten. Durch den Umstand, dass die Roboter die Wahl des Explorationsziels und die Pfadplanung selbstständig durchführen können, funktioniert das Roboterteam auch weiter, falls die Kommunikation zu den anderen Robotern abgebrochen wird. Wenn ein Roboter, der die Kommunkationsmöglichkeit mit dem Kartenserver verloren hat die Kommunikation wiederherstellen kann, können die in der Zwischenzeit gesammelten Daten des Roboters normal für das gesamte System weiter verwendet werden und der Roboter kann die Exploration koordiniert mit den anderen Robotern fortsetzen. Zusätzlich können von dem Kartenserver zusätzliche Informationen angefordert werden, die bei der Entscheidung über das nächste Explorationsziel des Roboters hilfreich sein können. Sollte die Kommunikation nicht wiederhergestellt werden können, wird die Exploration von jedem Roboter individuell und ohne Koordinierung fortgesetzt. Eine Kommunikation mit dem Kartenserver findet nur dann statt, wenn ein Roboter ein neues Explorationsziel benötigt. Dadurch ist die Netzwerkbelastung für die Koordinierung und die Kartenfusionen minimal und alle Roboter können unabhängig von den aufwändigen Berechnungen, die auf dem Kartenserver durchgeführt werden müssen weiter ihrer Aufgabe nachgehen. N2 - In this thesis, possibilities to perform a robust and resource-efficient method for homogenous autonomous robot teams for cooperative exploration and mapping of an unknown area are investigated. For this purpose, a cooperative exploration is performed to increase the efficiency for the task of mapping an area. This allows a global map of an unknown environment to be created with less effort and also in less time. The created global map can then be used by all involved robots for future tasks in the same area. To achieve this goal, various different map merging methods were examined, of which a feature detection-based procedure was selected for a distributed, robust and resource-efficient approach. After two or more maps are successfully merged, coordinated exploration can be performed with the robots that can work with the shared map. For the joint exploration, all frontiers that are present in the map are searched on the map server, which was implemented for this thesis. These are combined with the current exploration goals of the other robots and sent to the robot that is currently trying to select a new exploration goal. This allows all robots to work individually by themselves as well as independently of all other robots of the team with the information gathered by the others. Due to the fact that the robots can carry out the choice of the exploration goal and the path planning independently, the robot team continues to function if the communication with the other robots is interrupted. Furthermore, additional information can be requested from the map server, which can be helpful in deciding the next exploration goal of the robot. If a robot that lost communication with the server recovers communication, the data of the robot can still be used and the robot can just continue with the cooperative exploration without it causing a problem for the whole team. In the case that a robot can not re-establish communication with the server, each robot continues exploration individually and without coordination. Communication with the map server only takes place when a robot needs a new exploration goal. As a result, the network load for coordination and map merging is minimal and all robots can continue to perform their tasks regardless of the complex calculations that have to be performed on the map server. T2 - Robust and resource-efficient cooperative exploration and mapping using homogeneous autonomous robot teams Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3756 ER - TY - THES A1 - Rheinberger, Christoph T1 - Erkennung einer Link Layer Topologie durch passives Scannen N2 - In dieser Arbeit wird eine Topologie-Erkennung beschrieben, welche durch rein passives Scannen ermöglicht wird. Dazu werden die verschiedenen Protokolle beschrieben, welche in dem Bereich Digital Substation verwendet werden, um mögliche Ansätze zu erarbeiten. Es werden die Redundanz-Protokolle STP (Spanning Tree Protocol), RSTP (Rapid Spanning Tree Protocol), PRP (Parallel Redundancy Protocol) und HSR (High-availability Seamless Redundancy) beschrieben. Es wird ein kurzer Überblick zum IEC-61850 Standard und dessen Protokolle SV (Sampled Values) und GOOSE (Generic Object Oriented Substation Event) gegeben. Auf dieser Grundlage wird eine Applikation entwickelt, welche die Data Link Layer Topologie erkennt. Die entwickelte Topologie-Erkennung wird als Proof-of-Concept für STP und RSTP Netzwerke verwendet und die entsprechenden Voraussetzungen werden beschrieben. Auf korrektes Verhalten wurde die in dieser Arbeit entwickelte Applikation mittels verschiedenen, simulierten Netzwerken und einem simplen Laboraufbau getestet. Die Applikation bietet auch die Möglichkeiten, solche Topologien zu visualisieren und zu vergleichen. N2 - In this paper a topology recognition is described, which is realised by purely passive scanning. Therefore, the different protocols used in the field Digital Substation are described in order to develop possible approaches. The redundancy protocols STP (Spanning Tree Protocol), RSTP (Rapid Spanning Tree Protocol), PRP (Parallel Redundancy Protocol) and HSR (High-availability Seamless Redundancy) are explained to identify valid approaches. A short overview of the IEC-61850 standard and its protocols SV (Sampled Values) and GOOSE (Generic Object Oriented Substation Event) is given. With this information, an application is developed that recognizes the Data Link Layer topology. The eveloped topology scanner is used as proof of concept for STP and RSTP networks and the corresponding requirements are described. The application developed in this thesis was tested for correct behaviour using different simulated networks and a simple laboratory setup. Features are added to visualize and compare given topologies. T2 - Discovery of a link layer topology through passive scanning KW - Topologie KW - Netzwerk KW - Scannen KW - Data Link Layer KW - Sicherungsschicht Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3745 ER - TY - CHAP A1 - Ilg, Markus ED - Nadig, Linard ED - Behringer, Stefan T1 - Business Analytics im Controlling mit R BT - ein Flipped-Classroom-Lehrprojekt T2 - CARF Luzern 2020. Controlling. Accounting & Audit. Risk & Compliance. Finanzen N2 - Business Analytics zählt zu den Zukunftsthemen im Controlling. In der Controllinglehre spielt Analytics bisher aber nur eine untergeordnete Rolle. Der Beitrag beschreibt ein innovatives Lehrprojekt, das Studierende im Masterstudium Accounting, Controlling & Finance an der FH Vorarlberg befähigt, controllingrelevante Fragestellungen im Kontext von Business Analytics eigenständig zu beantworten. Gleichzeitig erlernen die Studierenden den Umgang mit der Open-Source-Software R. KW - Business analytics KW - Controlling KW - Flipped classroom Y1 - 2020 SN - 978-3-906877-73-0 SP - 361 EP - 377 PB - Verlag IFZ - Hochschule Luzern CY - Rotkreuz ER - TY - GEN A1 - Böhler, Doris T1 - Rezension zu: Nadja Hitzel-Abdelhamid: Onlineberatung. Ein Leitfaden zur Einführung für Beratungsstellen mit der Zielgruppe Menschen mit Migrationsgeschichte T2 - socialnet Rezensionen Y1 - 2020 UR - https://www.socialnet.de/rezensionen/27046.php ER - TY - THES A1 - Rosskopf, Ramona T1 - Analyse des Reduktionspotenzials von Ausgleichsenergie für Energieversorger durch autonomes Demand Side Management bei Haushaltskunden T1 - Analysis of the reduction potential of imbalanced energy for energy suppliers through autonomous demand side management for residential customers N2 - Die EU-Ziele umfassen die Steigerung des Anteils an erneuerbaren Energien an der Energieerzeugung um 32 % bis 2030. Doch erneuerbare Energien bringen neben den Vorteilen für den Umweltschutz auch Probleme mit sich. Ihre Schwankungen und Unkontrollierbarkeit stellen große Herausforderungen für das Stromnetz dar. Um die Netz- und damit die Versorgungssicherheit weiterhin gewährleisten zu können, braucht es Lösungen, die weder das Stromnetz, die Verbraucher noch die Energieversorger benachteiligen. Eine Möglichkeit wäre es, zusätzliche Kraftwerke und Infrastruktur (Redundanzen) aufzubauen, welche potenzielle Schwankungen ausgleichen können. Dieser Lösungsansatz gilt als traditioneller Weg, der hohe Kosten und negative Umweltauswirkungen mit sich bringt. Demand Side Management hat das Potenzial, effiziente Lösungen diesbezüglich anzubieten. Welche Vorteile der Einsatz von DSM auf Ebene der Haushaltsverbraucher für die Energieversorger in Bezug auf den Abruf von Ausgleichsenergie bringt, wird in dieser Arbeit behandelt. Dafür wurde ein agentenbasiertes Modell entwickelt, welches darauf abzielt, die Abweichung zwischen dem von dem Energieversorger prognostizierten Verbrauch und dem realen Verbrauch seiner Haushaltskunden zu verringern. Jeder Haushalt in dem vorgestellten Modell ist mit einer Flexibilität in Form eines Batteriespeichers ausgestattet. Die Speicherbewirtschaftung wird basierend auf einem Signal, welches der Energieversorger übermittelt, automatisch vom Haushalt für jeden Tag im Betrachtungszeitraum optimiert. Jede Abweichung zwischen der vom Energieversorger erstellten Prognose und der tatsächlich bezogenen Strommenge stellt dabei einen Bezug von Ausgleichsenergie dar. Untersucht werden die Auswirkungen der Anzahl an Haushalten sowie ein unterschiedlicher Wissensstand auf die Prognose. Weiters werden zwei unterschiedliche Arten von Demand Side Management analysiert. Einmal die Einflussnahme auf die Last der Haushalte durch ein Preissignal, einmal durch das Vorgeben eines Lastgangs. Um die Effektivität der beiden Varianten bestimmen zu können, wird auch die Menge an Ausgleichsenergie erhoben, welche ohne das Vorhandensein eines Batteriespeichers (also ohne Steuerung) anfallen würde. Das Modell wurde entwickelt, um einen Trend aufzuzeigen und keine spezifische Einsparungsmenge zu ermitteln, da dies von der jeweiligen Situation des Energieversorgers abhängt. Die Erstellung der unterschiedlichen Wissensstände basiert auf den österreichischen rechtlichen Vorgaben bezüglich der Datenübertragung bei intelligenten Messgeräten. Dabei ist einmal der Jahresverbrauch, einmal der Tagesverbrauch und einmal die stündlichen Verbrauchswerte bekannt. Das Preissignal ist negativ korreliert zu den am Day-Ahead-Markt gehandelten Mengen und das Lastsignal basiert auf einer der Prognosen des Energieversorgers, je nach Variante, die untersucht wird. Es zeigte sich, dass ein besserer Wissensstand nur teilweise eine Verbesserung der Prognose erzielte. Wobei die unterschiedlichen Wissensstände auf den realen Werten der nicht verwendeten Haushalte aus dem gleichen Datensatz aufbauen und so beispielsweise Wettereinflüsse in der Prognose schon bekannt waren, was die Prognose basierend auf Jahreswerten sehr genau machte. Der Aggregationseffekt von mehreren Haushalten beeinflusst die Prognose positiv. Auf einzelner Haushaltsebene schneiden die Vorhersagen deutlich schlechter ab als bei Prognosen des Gesamtverbrauchs aller Haushalte. Die Optimierung basierend auf dem Lastsignal generiert eine geringere Menge an Ausgleichsenergie als das Preissignal. Das liegt unter anderem daran, dass die Prognose nur die Verbräuche der Haushaltskunden berücksichtigt und nicht die Mengen, die am Markt gehandelt werden. In den untersuchten Varianten stellte sich heraus, dass am wenigsten Ausgleichsenergie über alle Haushalte erzeugt wird, wenn kein Demand Side Management betrieben wird, also keine Batteriespeicher vorhanden sind und die Prognose des Energieversorgers auf Stundenwerten basiert. Auf einzelner Haushaltsebene fällt bei der Optimierung mittels Lastsignal am wenigsten Ausgleichsenergie an. N2 - The EU goals include increasing the share of renewable energies in energy production by 32 % by 2030, but renewable energies also bring problems in addition to the environmental benefits. Their fluctuations and uncontrollability present major challenges for the electricity grid. In order to be able to continue to guarantee network reliability and thus supply security, solutions are needed that do not disadvantage the electricity network, consumers or energy suppliers. One option would be to build additional power plants and infrastructure (redundancies), which can compensate for potential fluctuations. This approach is the traditional way, which involves high costs and negative environmental impacts. Demand side management has the potential to provide efficient solutions in this regard. The advantages of using DSM at the level of residential consumers for energy suppliers in terms of imbalanced energy supply are discussed in this paper. For this purpose, an agent-based model was developed which aims to reduce the difference between the consumption forecast by the energy supplier and the real consumption of its residential customers. Each household in the presented model is equipped with flexibility in the form of a battery storage. The storage management is automatically optimized by the household for each day in the period under consideration based on a signal transmitted by the energy supplier. Any difference between the forecast made by the energy supplier and the amount of electricity actually consumed represents a purchase of imbalanced energy. The effects of the number of households and different levels of knowledge on the forecast are examined. Furthermore, two different types of demand side management are analysed. Firstly, the influence on the load of the households by a price signal, and secondly by the specification of a load profile. In order to determine the effectiveness of the two variants, the amount of imbalanced energy that would be produced without the presence of a battery storage (i.e. without control) is also collected. The model was developed to show a trend and not to determine a specific amount of savings, as this depends on the respective situation of the energy supplier. The preparation of the different levels of knowledge is based on the Austrian legal requirements regarding data transmission in smart meters. The annual, daily and hourly consumption values are known. The price signal is negatively correlated to the quantities traded on the day-ahead market and the load signal is based on one of the forecasts of the energy supplier depending on the variant under investigation. It turned out that a better knowledge base only partially improved the prediction. The different levels of knowledge were based on the real values of the unused households from the same data set, so that, for example, weather influences were already known in the prediction, which made the forecast based on annual values very accurate. The aggregation effect of several households positively influences the forecast. At the individual household level, the forecasts perform significantly worse than forecasts of the total consumption of all households. The optimization based on the load signal generates a smaller amount of imbalanced energy than the price signal. One reason for this is that the forecast only considers the consumption of household customers and not the quantities traded on the market. In the variations examined, it was found that the least amount of imbalanced energy is generated across all households when no demand side management is operated, i.e. when no battery storage is available, and the energy supplier's prediction is based on hourly values. At the individual household level, the least amount of imbalanced energy is generated during optimization using load signals. KW - Ausgleichsenergie KW - Demand Side Management KW - Energieversorger KW - Strommarkt Österreich Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3560 ER - TY - THES A1 - Baumann, Christian T1 - Autonome Steuerung für das Demand Side Management von Wärmepumpenboilern mit linearer Optimierung N2 - Wärmepumpen, im Speziellen Wärmepumpenboiler, stellen mit ihrer thermischen Speicherkapazität eine gute Möglichkeit für autonome verbraucherseitige Laststeuerung (Autonomes Demand Side Management ADSM) dar. Zudem gewinnt diese Art der Brauchwarmwassererzeugung durch ihren dezentralen Ansatz und das Auskommen ohne fossile Energieträger im privaten Wohnbau immer mehr an Bedeutung. In Kombination mit staatlichen Fördergeldern ist die Anzahl verkaufter Einheiten in den letzten 5 Jahren am deutschen Markt um circa 25 % gestiegen. Obwohl das Lastverschiebungspotenzial von Wärmepumpenboilern unter Anwendung von Optimierungsalgorithmen in der Literatur theoretisch nachgewiesen ist, fehlen Verifikationen unter realen Bedingungen. Diese Arbeit will einerseits das theoretische Potential aufzeigen und andererseits mit dem vorgestellten Laborversuch einen Beitrag dazu liefern, die Verifikationslücke zu schließen. Für die Untersuchung im Labor wird ein handelsüblicher Wärmepumpenboiler bestehend aus einer Luft-Wärmepumpe und einem 300 Liter Warmwasserspeicher mit Sensoren und Aktoren ausgestattet. Insgesamt vier Temperatursensoren befinden sich am Speicherzulauf und -ablauf, sowie nahe der Speichermitte. Für die Aufzeichnung des Volumenstroms wird ein magnetisch-induktiver Messsensor am Speichereingang installiert. Zusätzlich wird mithilfe eines Proportionalventils am Speicherausgang das gewünschte Zapfprofil realisiert. Die Datenakquisition wird durch einen Datenlogger durchgeführt und die Optimierungsroutine auf dem PC implementiert. Die autonome Steuerung basiert auf einer von Day-Ahead-Marktpreisen der Energy Exchange Austria (EXAA) getriebenen linearen Optimierung mit dem Ziel, die Kosten der elektrischen Energie zu minimieren. Das Warmwasserverbrauchsprofil bildet den Verbrauch eines 4- Personen-Haushalts ab. Alle Mess- und Simulationsreihen basieren auf den gleichen Day-Ahead Preisfunktionen und Nutzerprofilen. Zur Verifikation des Lastverschiebungspotentials werden die Kosten pro MWh elektrischer Energie und die Kosten pro MWh thermischer Nutzenergie im Hysteresebetrieb (Normalbetrieb) denen des optimierten Betriebs gegenübergestellt. Durch eine Jahressimulation konnte das theoretische Potential nachgewiesen werden. Die Auswertungen der Kosten pro MWh elektrischer Energie zeigen Kosteneinsparungen am Day-Ahead-Markt von rund 18 %. Die Kosten pro MWh thermischer Nutzenergie konnten durch die Optimierung um rund 19 % gesenkt werden. Die thermische Effizienz konnte somit um rund 1 % gesteigert werden. Der Wärmepumpenboiler wurde insgesamt zwei Wochen betrieben; eine Messreihe davon fand dabei im Normalbetrieb statt. In einer weiteren Messreihe wurde die Wärmepumpe mit der Optimierungsroutine betrieben. Die Auswertungen der Kosten pro MWh elektrischer Energie zeigen Kosteneinsparungen am Day-Ahead-Markt von circa 23 %. Ebenso konnten die Kosten pro MWh thermischer Nutzenergie um 19 % gesenkt werden. Gleichzeitig sank die thermische Effizienz um 6 %. N2 - With their thermal storage capacity heat pumps, in particular heat pump boilers are a good option for autonomous Demand Side Management (ADSM). In addition, this type of domestic hot water generation is becoming increasingly important in private residential building sector due to its decentralized approach and the fact that it does not require fossil fuels. In combination with government funding, the number of units sold on the German market has increased by around 25% in the past 5 years. Although the load shifting potential of heat pump boilers by using optimization algorithms is theoretically proven in literature, verifications under real conditions are missing. On the one hand this work aims to demonstrate the theoretical potential, on the other hand to contribute closing the verification gap with the laboratory test presented. For the investigation, a commercially available heat pump boiler consisting of an air sourced heat pump and a 300 liter hot water tank is equipped with sensors and actuators. A total of four temperature sensors are located at the storage inlet and outlet, as well as close to the middle of the storage. A magnetic-inductive measuring sensor is installed at the storage inlet to measure the volume flow. In addition, the desired user profile is realized by using a proportional valve at the storage outlet. The data acquisition is carried out by a data logger and the optimization routine is implemented on a PC. The autonomous control is based on a linear optimization driven by day-ahead market prices of the Energy Exchange Austria (EXAA) with the aim of minimizing the costs of electrical energy. The hot water consumption profile shows the consumption of a 4-person household. All measurement and simulation series are based on the same day-ahead price functions and user profiles. To verify the load shifting potential, the costs per MWh of electrical energy and the costs per MWh of thermal energy in hysteresis operation (normal operation) are compared with those of optimized operation. The theoretical potential could be demonstrated by an annual simulation. The evaluations of the costs per MWh show cost savings in the day-ahead market of around 18%. The optimization reduced the cost per MWh of thermal energy by around 19%. Thus, thermal efficiency could be increased by 1%. The heat pump boiler was operated for a total of two weeks, with the first series of measurements taking place in normal operation. In the following series of measurements, the heat pump was operated with the optimization routine. The evaluations of the costs per MWh of electrical energy show cost savings in the dayahead market of around 23%. The costs per MWh of thermal energy were also reduced by 19%. At the same time, thermal efficiency dropped by 6%. KW - Demand Side Management KW - Wärmepumpenboiler KW - autonome Optimierung KW - Systemidentifikation KW - experimenteller Aufbau Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3557 ER - TY - THES A1 - Breyer, Maximilian T1 - Digitalisierung von ÖKOPROFIT-Rohdaten – Erprobung eines KVP-Onlinetools anhand ausgewählter ÖKOPROFIT-Datensätze N2 - ÖKOPROFIT ist ein Kooperationsprojekt zwischen den örtlichen Gemeindenund der lokalenWirtschaft.Die Teilnahme ist für die Betriebe freiwillig. Ziel ist die Betriebskostensenkung bei gleichzeitiger Schonung der Ressourcen. In Vorarlberg sind derzeit circa170 Betriebe zertifiziert. Im Rahmen der Rezertifizierung, die jedes Jahr stattfindet, wird von den Betrieben ein Umweltbericht erstellt. Die Berichte werden derzeit in Word verfasst, in eine Cloud geladen und dort von den Auditoren geprüft. Dies ist jedoch nicht mehr zeitgemäß. Im Rahmen des CESBA-AlpsInterreg Alpine Projektes (2016-2019) wurde ein Tool entwickelt, mit dem Ziel Nachhaltigkeit und Energieeffizienz im Alpenraum zu verbessern. In dieser Arbeit wird nun geprüft, inwiefern das bestehende CESBA-Alps-Tool in Wert gesetzt und somit in den Rezertifizierungsprozess von ÖKOPROFIT integriert werden kann. Das Tool wird zunächst so eingerichtet, dass die Betriebe mit ihren dazugehörigenIndikatoren sowie passende Indikatoren-Sets angelegt werden können. Für den Test werden historische Daten bis zum Jahr 2013von zwei Pilot-Clustern (Landeskrankenhäuser und Landesregierungsgebäude) mit unterschiedlichen Indikatoren-Sets eingepflegt. Es wird untersucht, inwiefern die Auswertungen und Exporte für den Rezertifizierungsprozess bereits tauglich sind. Jegliche Auffälligkeiten, Fehler oder Verbesserungsvorschläge werden gesammelt. Es wird klar, dass die Export-Dateien verschlankt und optimiert werden müssen, damit sie ohne Mehraufwand verwertet werdenkönnen. Die wichtigste Handlungsempfehlung ist die automatisierte Berichtlegungsfunktion. Es sollte ein Texteditor in das Tool eingearbeitet werden, in den Unternehmen einzelne Textbausteine einpflegen können, sodass mithilfe des Tools nicht nur das Kennzahlenkapitel des Umweltberichts, sondern alle Kapitel standardisiert erarbeitet werden können. Nur so kann sichergestellt werden, dass das Tool für die Betriebe eine Arbeitserleichterung und somit Zeitersparnis generiert. In einem weiteren Arbeitspaketwurden ähnliche Online-Tools anhand von im Vorhinein ausgewählten und priorisierten Kriterien, die ein optimales Tool erfüllen sollte, mithilfe einer gewichteten Entscheidungsmatrix semiquantitativ verglichen. Hierbei schnitt das in dieser Arbeit getestete Tool selbst ohne die Verbesserungen am besten ab. Es stellt sich heraus, dass es bereits die Hälfte der ausgewählten Kriterien in einer sehr guten Weise erfüllt. Die Kriterien wurden von der ÖKOPROFIT-Programmleitung definiert. Werden die Handlungsempfehlungen in der Zukunft noch umgesetzt, könnte mit dem Tool tatsächlich eine Verbesserung des derzeitigen ÖKOPROFIT-Rezertifizierungsprozesses erwirkt werden. N2 - ÖKOPROFIT is a cooperation project between local communities and the local economy. Participation is voluntary for the companies. The aim is to reduce operating costs while simultaneously conserving resources. In Vorarlberg about 170 companies are currently certified. As part of the recertification process, which takes place every year, the companies prepare an environmental report. The reports are currently written in Word, loaded into a cloud and checked by the auditors. However, this is no longer up to date. Within the framework of the CESBA-Alps Interreg Alpine Project (2016-2019), a tool has been developed with the aim of improving sustainability and energy efficiency in the Alpine region. In this thesis it is now examined to what extent the existing CESBA-Alps tool can be put to good use and thus be integrated into the recertification process of ÖKOPROFIT. The tool will first be set up in such a way that the companies with their corresponding indicators as well as suitable sets of indicators can be created. For the test, historical data up to the year 2013 from two pilot clusters (state hospitals and state government buildings) with different indicator sets will be entered. The extent to which the evaluations and exports are already suitable for the recertification process will be investigated. Any anomalies, errors or suggestions for improvement are collected. It becomes clear that the export files must be streamlined and optimized so that they can be used without additional effort. The most important recommendation for action is the automated reporting function. A text editor should be incorporated into the tool, in which companies can enter individual text modules, so that the tool can be used to produce not only the key figure chapter of the environmental report, but all chapters in a standardised way. This is the only way to ensure that the tool makes work easier and thus saves time for the companies. In a further work package, similar online tools were compared semi-quantitatively using a weighted decision matrix on the basis of pre-selected and prioritised criteria that an optimal tool should fulfil. The tool tested in this work performed best even without the improvements. It turns out that it already meets half of the selected criteria in a very good way. The criteria were defined by the ÖKOPROFIT programme management. If the recommendations for action are still implemented in the future, the tool could actually bring about an improvement of the current ÖKOPROFIT recertification process. KW - Ökoprofit KW - Verbesserungsprozess KW - e5 KW - Tool Vergleich KW - KVP Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3558 ER - TY - THES A1 - Feistenauer, Raphael T1 - Untersuchungen der Einflussgrößen Wassertemperatur, Füllstand, Gasleerrohrgeschwindigkeit und Blasengröße auf die Befeuchtung von Luft in einer mit Salzwasser befüllten Blasensäule N2 - Das Ziel dieser Masterarbeit war die Untersuchung der Einflussgrößen Wassertemperatur, Füllstand, Gasleerrohrgeschwindigkeit und Blasengröße auf die Befeuchtung von Luft in einer mit Salzwasser befüllten Blasensäule. Dazu wurde eine umfangreiche Versuchsreihe durchgeführt, um die Auswirkungen zu untersuchen. Großer Wert wurde dabei auf die Reproduzierbarkeit der Ergebnisse gelegt. Es wurde eine große Anzahl Datensätze während den Versuchszeiten geloggt und analysiert. Die Auswertung hat ergeben, dass die Wassertemperatur ein wesentlicher Einflussfaktor auf die Befeuchtung von Luft ist. Die Wassertemperatur zeigt gemäß des Antoine-Gesetzes exponentielle Auswirkungen auf die Kondensatproduktion auf. Hohe Füllstände in der Blasensäule wiesen im Vergleich zu niedrigeren Füllständen eine erhöhte Kondensatproduktion auf. Eine Steigerung der Gasleerrohrgeschwindigkeit in den Versuchen führte zu einer Zu-nahme der produzierten Kondensatströme. Die in dieser Arbeit untersuchten Spargerplatten der Variation des Lochdurchmessers konnten keine klaren Erkenntnisse auf die Befeuchtung von Luft liefern. Insgesamt sind die Forschungen an der Versuchsanlage noch nicht abgeschlossen und weitere Erkenntnisse zu dieser Thematik sollen in Zukunft gewonnen werden. auf die Befeuchtung von Luft ist. Die Wassertemperatur zeigt gemäß des Antoine-Gesetzes exponentielle Auswirkungen auf die Kondensatproduktion auf. Hohe Füllstände in der Blasensäule wiesen im Vergleich zu niedrigeren Füllständen eine erhöhte Kondensatproduktion auf. Eine Steigerung der Gasleerrohrgeschwindigkeit in den Versuchen führte zu einer Zu- nahme der produzierten Kondensatströme. Die in dieser Arbeit untersuchten Spargerplatten der Variation des Lochdurchmessers konnten keine klaren Erkenntnisse auf die Befeuchtung von Luft liefern. Insgesamt sind die Forschungen an der Versuchsanlage noch nicht abgeschlossen und weitere Erkenntnisse zu dieser Thematik sollen in Zukunft gewonnen werden. N2 - The main purpose of this master thesis was to quantify the influence of water temperature, filling level, superficial gas velocity and bubble diameter on the humidification of air in a seawater filled bubble column. Various experiments have been performed. A major topic was the reproducibility of the results. A lot of data has been collected during the experiments and has been analysed. It turned out that the water temperature is an essential influence on the humidification of air. According to the Antoine law it has an exponential impact on the production of condensate. Higher filling levels have achieved greater condensate production than lower filling levels. With the increase of superficial gas velocity more condensate has been produced. The effect of using different spargerdesigns with varying hole diameters was also part of this research. No clear results concerning this topic could be delivered. In general, the research with the testing facility has not been finished yet. Further experiments are still ongoing and more insights to this topic shall be gained. KW - Luftbefeuchtung KW - Blasensäule KW - HDH Prozesse Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3559 ER - TY - THES A1 - Lopes, Eduardo T1 - Attractiveness of Swiss machinery, electrical and mechanical industry for acquisition by Indian companies BT - assessment and implications from a strategic perspective for the Swiss machinery, electrical and mechanical industry N2 - Companies develop and implement strategies with the aim to address the needs of their customers. Acquisition is one market expansion strategy that companies can use to acquire new market access, technologies and/or to grow organically. In recent years, Chinese companies have been active in acquiring companies all over the globe to develop their strategic position. This caused certain contra reaction in Europe and as well in the Swiss media against cross-border acquisitions of Swiss companies. Swiss companies and particularly the Swiss-MEM (Machinery, Electrical and Mechanical) industry is highly export oriented and their value proposition builds on attributes like knowledge, technology, and differentiating products. Among them are many “hidden champions” and niche players who successfully dominate the market segment. As observed with Chinese companies, Indian companies also started to become more active outside of their domestic markets by increasing their foreign direct investments into Europe, Asia and North America, over the last decades. The lasting and good relationship of India and Switzerland might trigger the wish for Indian companies to acquire Swiss and particularly Swiss-MEM companies for acquisitions. This Master’s Thesis assesses how often Indian investments into public and privately owned Swiss-MEM companies by acquisition happen, how are the attempts of acquisitions perceived by the stakeholders and what measures Swiss and Swiss-MEM companies can take, to protect themselves from being acquired. To access the research topic, several sub-questions will be analysed with the aid of primary and secondary research to assess the situation. The research topic is of particular interested to the author since he spent over 20 years working in the Swiss-MEM industry, involved in international affairs and in recent years specifically with India. The observation of Chinese acquisition activities and insight into the size and potential of India were the drivers for researching whether India might follow China’s example. In conclusion, Indian companies are not explicitly targeting Swiss and Swiss-MEM companies, but there are reasons to believe that it would make sense for Indian companies to look into the acquisition of Swiss and Swiss-MEM companies. The perception of such acquisitions varies, but there are arguments for and against them. Companies must take strategic and organisational measures in order to prevent themselves from becoming the target of an acquisition. However, it is known that the state should not interfere in the market and a discussion at a political level, planning how to deal with cross-border acquisition, is needed. Further areas for research based on this Master’s Thesis could be the review of how the targeting of Swiss and Swiss-MEM companies by Indian companies would look, and also the topic of the succession planning in Swiss secondary sector in conjunction with Indian targeting for acquisitions. A third area to research might be investigating the political aspects involved in the research questions. KW - International business KW - Acquisitions KW - Swiss-MEM KW - India KW - Switzerland Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3694 ER - TY - THES A1 - Zumbiel, Sandra T1 - Ideen zur Reduktion des Pflegefachkräftemangels BT - Potenzialanalyse aus Business Process Management-Sicht N2 - Die Suche nach geeigneten Maßnahmen im Kampf gegen den Pflegefachkräftemangel geht lange Zeit zurück. Immer mehr schnelle und nicht abgestimmte Lösungen kommen dabei auf. Um wirksam die Personallücke schließen zu können, muss an den Problemursachen angeknüpft werden. In dieser Masterthesis wird der Personalmangel aus einer neuartigen Perspektive betrachtet. Mit Hilfe des Prozessfokus werden die existierenden Ideen mit folgender Fragestellung näher begutachtet: „Inwieweit spielt Business Process Management (BPM) eine Rolle bei den bisherigen Ideen? Kann BPM einen Beitrag zur Arbeitsentlastung der Pflegekräfte und damit zur Linderung des Personalmangels leisten?“ Um diese Frage beantworten zu können, ist eine zweiteilige Methodik erforderlich. Die Literaturrecherche wird mit dem Wissen aus einer Prozessbegehung ergänzt. Da die Kombination verschiedener Methoden ein Basisfachwissen voraussetzt, ist die Zielgruppe durch dieses Faktum definiert. Am Ende kann die Digitalisierung in Verbindung mit organisatorischen Umstrukturierungen als geeigneter BPM-Lösungsansatz betitelt werden. Dieser knüpft an den Basisanforderungen an, um auf lange Sicht den Pflegemangel beherrschbar machen zu können. N2 - The search for suitable measures in the fight against the shortage of nursing staff has been slowing down for a long time. More and more fast and uncoordinated solutions are emerging. In order to be able to effectively close the personnel gap, the problem has to be tackled at the root causes. In this Master's thesis, the personnel gap is viewed from a new perspective. By focusing on the processes, the existing ideas are examined in more detail with the following question: „To what extent does Business Process Management (BPM) play a role in the previous ideas? Can BPM contribute to relieve the workload of nurses and thus to alleviate the shortage of staff?" In order to be able to answer this question, a two-part methodology is required. The literature research is complemented by the knowledge from a process inspection. Since the combination of different methods requires basic expertise, the target group is defined by this fact. In the end, digitization in connection with organizational restructuring can be called a suitable solution. This ties in with the basic requirements in order to make the shortage of care manageable in the long term. The BPM role is demonstrably present. T2 - Ideas for reducing the shortage of nursing staff : potential analysis from a business process management perspective Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3686 ER - TY - THES A1 - Maier, Katharina T1 - Sustainable distribution BT - developing a model to evaluate environmental and social sustainability impacts of selected distribution channels in international businesses on the example of the banking industry N2 - This master thesis gives an insight into the topic of sustainability in the banking industry and focuses on distribution. In the first part of the thesis, the terms and concepts of sustainability and sustainable distribution are being explained and existing methods for measuring sustainability are presented on the basis of an extensive literature research. Subsequently, the banking industry is introduced, the distribution of financial services is explained, and the specifics of sustainable distribution in the banking industry are elaborated. An empirical study in form of expert interviews was used to show to what extent sustainability currently plays or will play a role in the banking sector. For this purpose, experts from six banks were interviewed. In the final part of the paper, the hypotheses formulated at the beginning of the paper as well as additional questions are examined or answered and a model for evaluating the effects of selected distribution channels on ecological and social sustainability is being presented. N2 - Die vorliegende Master Arbeit gibt einen Einblick in das Thema Nachhaltigkeit in der Bankenbranche und fokussiert dabei auf die Distribution, wobei im ersten Teil der Arbeit zunächst die Themen Distribution, Nachhaltigkeit und nachhaltige Distribution erläutert werden und anschließend bereits bestehende Methoden zur Messung von Nachhaltigkeit vorgestellt werden. Grundlage dieses Teils der Arbeit ist eine extensive Literaturrecherche. Im darauffolgenden Teil wird die Bankenbranche vorgestellt, die Distribution von Finanzdienstleistungen erläutert und Besonderheiten der nachhaltigen Distribution eben dieser herausgearbeitet. Nachfolgend zeigt eine empirische Studie in Form von Experteninterviews auf, inwiefern Nachhaltigkeit aktuell aber auch in der Zukunft eine Rolle in der Bankenbranche spielt bzw. spielen wird. Hierzu wurden Expertinnen und Experten von sechs Banken interviewt. Im letzten Teil der Arbeit werden die eingangs formulierten Hypothesen sowie ergänzenden Fragestellungen überprüft beziehungsweise beantwortet, sowie ein Modell zur Bewertung der Auswirkungen ausgewählter Distributionskanäle auf die ökologische und soziale Nachhaltigkeit vorgestellt. T2 - Nachhaltige Distribution : Entwicklung eines Modells zur Bewertung der Auswirkungen ausgewählter Distributionskanäle auf die ökologische und soziale Nachhaltigkeit am Beispiel der Bankenbranche KW - Distribution KW - Sustainability KW - Sustainable distribution Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3649 ER - TY - THES A1 - Ares, Graziela T1 - The internationalization of the firm BT - an analysis of a Brazilian eucalyptus pulp exporter in 2018 based on Uppsala and Bartlett & Ghoshal models N2 - The present research had compared how Uppsala and Bartlett & Ghoshal (B&G) models explain the internationalization process of the Brazilian pulp producer Fibria. The Uppsala model describes the developments of capabilities that enable the firm to move towards higher commitments abroad. Despite its sine-qua-non dependence on foreign markets, it is unlikely that Fibria will internationalize its production to another country, given the country-specific advantages that the company has in Brazil. Nevertheless, Fibria set its structure abroad even when the direct exports would suffice to reach the markets without any foreign direct investment. B&G deals with the aspects of the organizational structure and described the Transnational type as the evolution of the international firm. In their typology, Fibria was a Global and Ethnocentric type, but interestingly, elements of Transnational and Geocentric models were also observed in the company. Both theories overlap or complement each other in many aspects. However, they could not explain the peculiarities of the internationalization of Fibria. One reason is the lack of country-related elements in these models. Eventually, comparisons between theories such as those presented enable decision-makers to align the corporate strategy using suitable models, bearing in mind the limitations that each method entails. N2 - Die vorliegende Studie vergleicht, wie die Modelle von Uppsala und Bartlett & Ghoshal (B&G) den Internationalisierungsprozess des brasilianischen Zellulose-Produzenten Fibria erklären. Das Uppsala-Modell beschreibt die Entwicklung von capabilities, die es dem Unternehmen ermöglichen, ein höheres Maß an commitment im Ausland einzugehen. Trotz der unweigerlichen Abhängigkeit von ausländischen Märkten ist es unwahrscheinlich, dass Fibria seine Produktion in ein anderes Land auslagern wird, da das Unternehmen in Brasilien über länderspezifische Vorteile verfügt. Fibria hat seine Vertriebsstrukturen im Ausland demnach festgelegt, auch wenn die direkten Exportmöglichkeiten ausreichen würden, um eine Marktbearbeitung ohne ausländische Direktinvestitionen zu ermöglichen. Bartlett und Ghoshal beschäftigen sich mit dem Aspekt der Organisationsstruktur und beschreibt den Transnational-Typus als die Evolution eines internationalen Unternehmens. Anhand dieser Typologie entspräche Fibria dem globalen und ethnozentrischen Typus, wobei auch Elemente des transnationalen und geozentrischen Modells im Unternehmen beobachtet werden konnten. Beide Theorien überschneiden sich in vielen Aspekten oder ergänzen sich. Sie konnten jedoch die Besonderheiten der Internationalisierung von Fibria nicht erklären. Ein Grund hierfür liegt im Fehlen länderspezifischer Elemente dieser Modelle. Letztlich dienen Vergleiche zwischen Theorien wie den beiden vorgestellten dazu, es EntscheiderInnen zu ermöglichen, die Unternehmensstrategie mittels eines passenden Modells auszurichten - unter Berücksichtigung der Einschränkungen, die die jeweilige Theorie mit sich bringt. T2 - Internationalisierung von Unternehmen : Analyse eines brasilianischen Eucalyptus-Zellstoff-Exporteurs im Jahres 2018, basierend auf den Theorien von Uppsala und Bartlett & Ghoshal KW - Internationalization of the firm KW - Brazilian KW - Pulp industry KW - Uppsala model KW - Bartlett & Ghoshal model Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3639 ER - TY - THES A1 - Hämmerle, Simon T1 - Ansätze zur datengetriebenen Prozessinnovation BT - eine Betrachtung mit Fokus auf ERP- und CRM-Systeme produzierender Unternehmen N2 - In einer Zeit, in der Daten eine immer größere Rolle spielen, nehmen Schlagwörter wie Big Data, Data Analytics oder Data Mining auch in Organisationen eine große Rolle ein. Daten werden zum neuen digitalen Öl, das durch alle Systeme der Unternehmen und externe Quellen fließt. Richtig eingesetzt, unterstützen sie bei der Strategiefindung, bei der Umsetzung neuer Geschäftsmodelle, beim Gestalten neuer Abläufe und Prozesse und insbesondere bei der Entscheidungsfindung. Die vorliegende Arbeit beschäftigt sich mit den Themen Daten und Unternehmenssystemen. Von diesen Themen ausgehend wird versucht, eine Brücke zu den Themenfeldern Prozessmanagement und Prozessinnovation zu schlagen. Die Arbeit soll aufzeigen, welche strategischen und operativen Ansätze die Nutzung von Daten als Treiber für Prozessinnovation zulassen. Aufbauend auf einer theoretischen Einordnung der vier skizzierten Gebiete, bildet ein empirischer Teil das Herzstück dieser Arbeit. In diesem Teil werden Aussagen von ExpertInnen darüber zusammengetragen, welche Ansätze zur datengetriebenen Prozessinnovation sie in ihren jeweiligen Unternehmen anwenden. Diese Aufarbeitung ist gegliedert in die drei Ebenen Rahmenbedingungen, Faktoren und Ansätze. Abgeschlossen wird diese Arbeit durch konkrete Handlungsempfehlungen für Unternehmen. N2 - In a time where data is playing an ever-increasing role, keywords such as Big Data, Data Analytics or Data Mining tend to play a major role in organisations. Data is becoming the new digital oil that flows through all corporate systems and external sources. Used correctly, this data supports in strategy development, implementation of new business models, design of new procedures and processes, and especially decision-making. This paper mainly deals with the topics data and enterprise systems. Starting from these topics, an attempt is made to build a bridge to the topics of process management and process innovation. The purpose of this thesis is to show which strategic and operative approaches allow the use of data as a driver for process innovation. Based on a theoretical classification of the four outlined topics, an empirical part forms the core of this paper. This empirical part contains a collection of expert statements and analyses their approach on handling the topic of data driven process innovation. The presentation is divided into three levels: frame conditions, factors and approaches. The paper concludes in concrete recommendations for companies. T2 - Approaches to data-driven process innovation Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3691 ER - TY - THES A1 - Ziegler, Michael T1 - Algorithmen und ihre Implikationen auf Management-Kompetenzen BT - wie wirken sich Machine Learning und Künstliche Intelligenz auf die Anforderungen an Management-Kompetenzen aus? N2 - Die Entwicklungen im Bereich der Algorithmen, Machine Learning und Künstlicher Intelligenz sind rasant und halten Einzug in immer mehr Bereichen des alltäglichen Lebens, insbesondere in den Unternehmen. Aus diesem Grund wird in dieser Arbeit der Frage nachgegangen, inwiefern dieser Trend Auswirkungen auf die benötigten Management-Kompetenzen hat. Zur Beantwortung dieser Frage wird zuerst die klassische Management-Lehre mit ihren zentralen Begrifflichkeiten und bestehenden Kompetenzmodellen beleuchtet und basierend auf diesen Erkenntnissen ein Analyse-Hilfsmodell entwickelt. Im Anschluss werden die wichtigsten Grundlagen zum Themenkomplex Algorithmus, Machine Learning und Künstliche Intelligenz behandelt und auf dieser Basis benötigte Management-Kompetenzen abgeleitet. Zusätzlich werden aktuelle Studien großer Beratungsunternehmen und Fachartikel analysiert und ebenfalls Kompetenzen für den Einsatz von Machine Learning und Künstlicher Intelligenz identifiziert. Schliesslich wird eine Gap-Analyse durchgeführt mit dem Resultat, dass keine grundsätzlich neuen Kompetenzen notwendig sind, diese jedoch teils erweitert werden müssen und sich deren Wichtigkeit verschiebt. KW - Künstliche Intelligenz KW - Management-Kompetenzen KW - Machine learning Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3679 ER - TY - THES A1 - Weber, Vanessa T1 - Cultural Due Diligence BT - does it matter in cross-border M&As? N2 - Much research has been conducted in recent years to discover the reasons for the high failure rate of M&As, whereas one frequently cited reason is the incompatibility of the corporate cultures. In order to minimize this risk and to be able to react to these differences already at an early stage, Cultural Due Diligence offers itself as part of the due diligence process. Unlike existing, more general research, I emphasize the cultural challenges companies face when investing transnationally with this thesis. Using the results of a single case study with inductive character, I answer the question how to conduct Cultural Due Diligence in cross-border M&As and propose an appropriate model. The findings reveal that especially in cross-border M&As, cultural incompatibility poses a risk for failure. I was able to find out that companies that seek to grow internationally with M&As deal with similar issues in terms of corporate culture as pointed out in existing Cultural Due Diligence methods. The present study, however, shows that national culture has a great influence on corporate culture, which is why it is essential to include it in the cultural assessment in cross-border acquisitions. This provides information about why there are differences, besides the fact that they exist. Only this understanding puts a company in the appropriate starting position to recognize differences, understand them, assess whether these differ-ences are acceptable, as well as to develop appropriate strategies to address them in the integration phase. N2 - In den vergangenen Jahren wurden zahlreiche Forschungsarbeiten durchgeführt, um die hohe Misserfolgsquote bei Fusionen und Akquisitionen zu ergründen. Ein in diesem Zusammenhang häufig angeführter Faktor stellt dabei die Inkompatibilität der Unternehmenskulturen dar. Um ein solches Risiko zu minimieren und bereits frühzeitig auf etwaige kulturelle Unterschiede reagieren zu können, bietet sich die Cultural Due Diligence als Teilprozess des Due Diligence Prozesses an. Im Vergleich zu bestehenden, allgemein gehaltenen Untersuchungen, stelle ich im Rahmen dieser Arbeit die kulturellen Herausforderungen heraus, denen Unternehmen bei transnationalen Investitionen gegenüberstehen. Anhand der Ergebnisse einer Einzelfallstudie mit induktivem Charakter beantworte ich die Frage, wie eine Cultural Due Diligence bei einem grenzüberschreitenden M&A durchgeführt werden kann und schlage ein dafür geeignetes Modell vor. Die Ergebnisse zeigen, dass vor allem bei grenzüberschreitenden M&A-Transaktionen die kulturelle Unvereinbarkeit ein erhöhtes Risiko für das Scheitern darstellt. Ich konnte herausfinden, dass Unternehmen, die mit Fusionen und Unternehmensübernahmen auf internationaler Ebene wachsen wollen, mit vergleichbaren unternehmenskulturellen Themen konfrontiert sind, wie sie in bestehenden Cultural Due Diligence Methoden aufgezeigt werden. Die vorliegende Untersuchung verdeutlicht jedoch, dass die nationale Kultur einen großen Einfluss auf die Unternehmenskultur hat, weshalb es unerlässlich ist, sie in die kulturelle Bewertung bei grenzüberschreitenden Übernahmen einzubeziehen. Nur so lässt sich neben der Tatsache, dass es Unterschiede gibt, verstehen, warum es diese gibt. Erst dieses Verständnis versetzt ein Unternehmen in die geeignete Ausgangslage, Unterschiede in der Unternehmenskultur zu erkennen, diese zu verstehen, zu beurteilen, ob diese Unterschiede akzeptabel sind, sowie geeignete Strategien zu entwickeln, um diese Unterschiede in der Integrationsphase entsprechend zu adressieren. T2 - Cultural Due Diligence : macht es bei grenzüberschreitenden M&A-Transaktionen Sinn? KW - Cultural Due Diligence KW - Cross-border M&A KW - Corporate culture Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3690 ER - TY - THES A1 - Bilgeri, Nadine T1 - Artificial intelligence improving CRM, sales and customer experience BT - an analysis of an international B2B company N2 - Nowadays, the area of customer management strives for omni-channel and state-of-the-art CRM concepts including Artificial Intelligence and the approach of Customer Experience. As a result, modern CRM solutions are essential tools for supporting customer processes in Marketing, Sales and Service. AI-driven CRM accelerates sales cycles, improves lead generation and qualification, and enables highly personalized marketing. The focus of this thesis is to present the basics of Customer Relationship Management, to show the latest Gartner insights about CRM and CX, and to demonstrate an AI Business Framework, which introduces AI use cases that are used as a basis for the expert interviews conducted in an international B2B company. AI will transform CX through a better understanding of customer behavior. The following research questions are answered in this thesis: In which AI use cases can Sales and CRM be improved? How can Customer Experience be improved with AI-driven CRM? N2 - Heutzutage strebt der Bereich des Kundenmanagements nach Omni-Channel- und modernen CRM-Konzepten unter Einbeziehung künstlicher Intelligenz und dem Ansatz der Customer Experience. Daher sind moderne CRM-Lösungen unverzichtbare Werkzeuge zur Unterstützung von Kundenprozessen in Marketing, Vertrieb und Service. KI-getriebenes CRM beschleunigt die Verkaufszyklen, verbessert die Lead-Generierung und -Qualifizierung und ermöglicht ein hoch personalisiertes Marketing. Der Schwerpunkt dieser Arbeit liegt auf der Darstellung der Grundlagen des Customer Relationship Managements und den neuesten Erkenntnissen von Gartner zu CRM und CX, sowie der Veranschaulichung eines KI Business Frameworks, welches KI-Anwendungsfälle vorstellt, die als Grundlage für die Experteninterviews in einem internationalen B2B-Unternehmen dienen. KI wird die CX durch ein besseres Verständnis des Kundenverhaltens transformieren. In dieser Arbeit werden die folgenden Forschungsfragen beantwortet: In welchen KI-Anwendungsfällen können Vertrieb und CRM verbessert werden? Wie kann die Customer Experience mit KI-gesteuertem CRM verbessert werden?   T2 - Künstliche Intelligenz zur Verbesserung von CRM, Vertrieb und Customer Experience KW - Artificial intelligence KW - Customer relationship management KW - Customer experience KW - Sales KW - AI use cases Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3646 ER - TY - THES A1 - Abouelkasem, Ahmed T1 - A novel calorimetric technique for the analysis of gas-releasing endothermic dissociation reactions BT - A method for the analysis of the gas hydrate decomposition process KW - Calorimetry KW - Endothermy KW - Gas hydrate Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3561 ER - TY - THES A1 - Ortiz-Portuguez, Paula A. T1 - The impact of culture and operational CRM on new product development BT - examples from Austrian and Costa Rican SMEs N2 - This research seeks to explore the cultural impact in the development of a new product, and if operational CRM (CRM technologies) can bring these two concepts together. As an industrial designer, the researcher finds it fascinating to explore how the abilities that a designer uses can help to solve users' problems could be implemented into structural or strategic decision-making of a company. Therefore, the researcher believes that the results might bring value to the head of international teams in charge of Product Development, by bringing some ideas for what is essential to consider in these processes and how CRM could become a relevant tool to satisfy customers and users. This research generates value to international management and leadership studies because it brings the management of new product development from an organizational point of view within an international context to the forefront. It also builds an understanding of what to consider when the value chain is decentralized and involves international collaboration in product development processes. And positive elements and/or problems that may arise concerning culture and the role of the CRM within this process. N2 - Esta investigación busca explorar el impacto cultural en el desarrollo de un nuevo producto, y si el CRM operacional (tecnologías CRM) puede unir estos dos conceptos. Como diseñador industrial, el investigador encuentra fascinante explorar cómo las habilidades que un diseñador utiliza pueden ayudar a resolver los problemas de los usuarios podrían implementarse en la toma de decisiones estructurales o estratégicas de una empresa. Por lo tanto, el investigador cree que los resultados podrían aportar valor a los líderes de los equipos internacionales encargados del desarrollo de productos, aportando algunas ideas sobre lo que es esencial tener en cuenta en estos procesos y cómo el CRM podría convertirse en una herramienta relevante para satisfacer a los clientes y usuarios. Esta investigación genera valor para los estudios de gestión y liderazgo internacional porque pone en primer plano la gestión del desarrollo de nuevos productos desde el punto de vista organizativo en un contexto internacional. También permite comprender qué hay que tener en cuenta cuando la cadena de valor se descentraliza e implica la colaboración internacional en los procesos de desarrollo de productos. Y los elementos positivos y/o los problemas que pueden surgir en relación con la cultura y el papel de la CRM dentro de este proceso. T2 - El impacto de la cultura y el CRM operacional en el desarrollo de nuevos productos : ejemplos de PYMES de Vorarlberg y Costa Rica KW - SME KW - NPD KW - International business KW - Design management KW - Culture Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3733 ER - TY - THES A1 - Hefel, Elisa T1 - Effective leadership behaviours during change management with multicultural teams N2 - This master thesis investigates effective leadership behaviour of multicultural teams during change management. Multicultural teams can be highly effective in dealing with complex change processes and can represent a key player to tackle today’s VUCA-world challenges. Effectiveness of multicultural teams during change depends critically on leadership with a range of specific behaviours. Involvement and support of the employees in a coaching role is key. Leaders need to display behaviours such as continuous development of cultural and emotional intelligence, critical self-reflection, open-mindedness, and readiness to serve as authentic role models. Furthermore, the creation of a sense of unity based on good communication and common sense is essential to build multicultural teams, and to enable them to embrace their differences as opportunity. Trust, transparency and a holistic change process are vital. Effectiveness essentially depends on the following factors: the organization’s culture, the characteristics of the employees and of their leader, and on the external environment. Leaders should take these factors into consideration at all times. KW - Leadership behaviour KW - Multicultural teams KW - Change management Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3726 ER - TY - THES A1 - Husejnagic, Dino T1 - Digitale Transformation mit Hilfe der Unternehmensarchitektur BT - Anforderungen an das EAM im digitalen Wandel und die Business Values für Organisationen N2 - Digitale Transformation ist heutzutage eine Pflichtaufgabe. Die Literatur zu dem Themengebiet bietet sehr viel Auswahl. Trotzdem fehlt es immer noch an einem gängigen Konzept, welches bei der digitalen Transformation unterstützten soll. Dementsprechend beschäftigt sich die vorliegende Masterarbeit mit der Fragestellung, ob es sich beim Enterprise Architecture Management (EAM, auf Deu. Unternehmensarchitektur) um so ein gängiges Konzept handeln könnte. Um dies zu beantworten und eine gewisse Übersicht in den Stand der aktuellen Forschung zu bringen, wurde eine Literaturrecherche durchgeführt. Diese beinhaltet neben den theoretischen Hintergründen zur digitalen Transformation und EAM auch noch ein Ausarbeiten der digitalen Anforderungen an das EAM. Ein EA-Framework wird als Referenzmodell ausgewählt und anhand der neuen Anforderungen einer kritischen Betrachtung unterzogen. Die Arbeit soll zum einen Erkenntnisse darüber liefern ob es ich sich bei dem gewählten Framework um ein mögliches Werkzeug handelt, welches bei der digitalen Transformation einen Mehrwert liefert. Zum anderen soll sie zeigen ob mit EAM die Lücke zum fehlenden Konzept geschlossen werden kann. N2 - Digital transformation is a mandatory task nowadays. The literature on the topic offers a wide range of choice. Nevertheless, there is still a lack of a common concept which is supposed to support the digital transformation. Accordingly, this master thesis deals with the question whether Enterprise Architecture Management (EAM) is such a common concept. In order to answer this question and to provide a certain overview of the current state of research, a literature review was conducted. In addition to the theoretical background of digital transformation and EAM, this also includes a elaboration of the digital requirements for EAM. An EA framework was selected as a reference model and subjected to a critical examination based on the new requirements. On the one hand, the work should provide insights into whether the chosen framework is a possible tool that provides added value in digital transformation. On the other hand it should show if EAM can close the gap to the missing concept. T2 - Digital transformation with support of enterprise architecture : requirements for the EAM within the digital change and the business values for the organisations KW - Unternehmensarchitektur KW - Digitale Transformation KW - EAM KW - Enterprise architecture KW - TOGAF Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3730 ER - TY - THES A1 - Hoffmann, Louis T1 - Digital transformation in destination management BT - development of a multi-sided platform business model for destination management organisations N2 - Digitalisation poses great challenges for regional tourism management. However, many organisations are currently undergoing a transformation from a marketing to a destination management organisation (DMO), which is why only a few have managed to adopt new digital approaches and to assert themselves as DMOs within the destination and against ever growing global platforms. The presented master thesis therefore deals with this issue and aims to pave the way for DMOs to develop and use digital business models themselves. The objective of the thesis is to develop a systematic process for the development of own DMO business models and to evaluate whether the establishment of a multi-sided platform as the recipe for the success of global platform providers is also suitable for DMOs. For this purpose, an extensive literature research was conducted and semi-structured expert interviews were evaluated. In addition, the Anchor Point Canvas was developed as a supporting framework for the modelling of business models for companies with historically grown structures and constraints. N2 - Die Digitalisierung stelle das regionale Tourismusmanagement vor große Herausforderungen. Viele Organisationen befinden sich allerdings aktuell im Wandel von einer Marketing- zu einer Destinationsmanagementorganisation (DMO), weshalb es bislang nur wenige geschafft haben, neue digitale Wege einzuschlagen und sich als DMO innerhalb der Destination und gegenüber immer stärker werdenden globalen Plattformen zu behaupten. Die vorliegende Masterthesis beschäftigt sich daher mit diesem Thema und soll den Weg für DMOS ebnen, digitale Geschäftsmodelle selbst zu entwickeln und zu nutzen. Ziel der Arbeit ist es, einen systematischen Prozess zur Entwicklung eigener DMO Geschäftsmodelle zu entwickeln und zu bewerten, ob der Aufbau einer Multi-sided Platform als Erfolgsrezept globaler Anbieter, auch für DMOs geeignet ist. Dazu wurde eine umfangreiche Literaturrecherche durchgeführt sowie semi-strukturierte Experteninterviews ausgewertet. Darüber hinaus wurde im Rahmen der Thesis das Anchor Point Canvas als unterstützendes Werkzeug bei der Modellierung von Geschäftsmodellen für Unternehmen mit historisch gewachsenen Strukturen und Einschränkungen entwickelt. T2 - Digitale Transformation im Destinationsmanagement : Entwicklung eines Multi-sided Platform-Geschäftsmodells für Destinationsmanagementorganisationen Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3704 ER - TY - THES A1 - David, Patricia T1 - Einkauf 4.0 BT - eine Umfangsdefinition und Analyse der Umsetzung der gefundenen Merkmale des Einkauf 4.0 in der Praxis N2 - Traditionelle Einkaufsprozesse haben viele Fehlerquellen und ungenütztes Potential. Viele Konzepte, die meist im Zusammenhang mit Digitalisierung und Industrie 4.0 stehen, versprechen Optimierungen. Diese Vielfalt führt jedoch in der Praxis zu Unklarheiten, da fraglich ist, was tatsächlich hinter den Konzepten steckt. Insbesondere der sogenannte „Einkauf 4.0“, der mehr als eine Digitalisierung der Beschaffungsprozesse verspricht, wirft viele Fragen auf. Das Ziel der vorliegenden Forschungsarbeit ist es festzulegen, welche Merkmale dem „Einkauf 4.0“ zugeschrieben werden können und ob sich diese in Praxis wiederfinden. Dazu werden folgende Forschungsfragen gestellt: 1. Welche Merkmale können eindeutig dem Begriff „Einkauf 4.0“ zugeordnet werden, um eine aktuell gültige Umfangsdefinition zu erstellen? 2. Werden die gefundenen Merkmale des Einkauf 4.0 in der Praxis als relevant erachtet und umgesetzt? Falls ja, welche? Um die erste Forschungsfrage zu beantworten wurden eine qualitative und eine quantitative Inhaltsanalyse durchgeführt. Die Merkmale des Begriff Einkauf 4.0 konnten dadurch eindeutig festlegt und abgrenzt werden. Die zweite Forschungsfrage wurde beantwortet in dem ein Vergleich der gefundenen Merkmale mit der Studie „BME-Barometer Elektronische Beschaffung 2020“ des BME e. V. erfolgte. Die Auswertung der Inhaltsanalysen zeigt, dass sich Merkmale für den Einkauf 4.0 finden lassen, diese jedoch kritisch zu hinterfragen sind. Der Vergleich der Merkmale mit der Studie des BME e.V., ergibt, dass einige Merkmale in der Praxis wiederzufinden sind; Sie sind jedoch von unterschiedlicher Relevanz. Weiterführende Forschung ausgehend von der hier formulierten Definition würden tiefere Einblicke in das Konzept des Einkauf 4.0 ermöglichen. N2 - Traditional procurement processes have a lot of problems and unused potential. Many concepts, which are mostly related to digitization and Industry 4.0, promise optimization. However, this diversity leads to ambiguities in practice, as many concepts are questionable. Especially the so-called "Einkauf 4.0", which promises more than just the digitalization of procurement processes, raises many questions. The aim of the present research work is to determine which characteristics can be attributed to "Einkauf 4.0" and whether these can be found in practice. Therefore the following research questions are formulated: 1. Which characteristics can be assigned clearly to the term "Einkauf 4.0" in order to create a currently valid scope definition? 2. Are the characteristics found for Einkauf 4.0 considered relevant and implemented in practice? If so, which ones? In order to answer the first research question, a qualitative and a quantitative content analysis were conducted. As a result of this, the characteristics of the term Einkauf 4.0 could be clearly defined and delimited. The second research question was answered by comparing the characteristics found with the study "BME-Barometer Electronic Procurement 2020" of the BME e. V. The evaluation of the content analyses shows that characteristics for Einkauf 4.0 can be found, but that these should be critically reviewed. The comparison of the characteristics with the study of the BME e.V. shows that some characteristics can be found in practice - but they are of different relevance. Further research based on the definition formulated in this Thesis would provide deeper insights into the concept of Einkauf 4.0. T2 - Einkauf 4.0 : a scope definition and analysis of the implementation of the identified characteristics of Einkauf 4.0 in practice KW - Einkauf 4.0 KW - Industrie 4.0 KW - Digitalisierung KW - Digitalisierung im Einkauf Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3709 ER - TY - THES A1 - Lins, Simon T1 - Effects of the digitalisation of sales processes on the sales force in the B2B environment BT - a case study at the example of the heating industry in Central Europe N2 - Throughout history, a variety of influences have changed the way we sell our products. Starting with the Industrial Revolution up to the first saturation phase in the 1970s. The question now arises as to whether the heating industry is currently back on an evolutionary development path with the increasing digitalisation of distribution. How the sales process in the B2B sector will change with increasing digitalisation and what effects this will have on sales personnel is only documented by a few sources which do not allow any conclusions to be drawn about the craft or even the heating industry. This results in a research gap which is to be closed in the context of this thesis. The aim of this research project is to find out the effects of a further digitalisation of the sales process on the sales force in the defined environment of the heating industry in Central Europe. For this purpose the following research questions are asked: Which steps in the sales process in the heating industry in Central Europe should be digitalised? How will the digitalisation of the sales process affect the sales force in the heating industry in Central Europe? A case study, according to Yin was chosen as the research method. The data were collected by means of in-depth interviews and analysed qualitatively, according to Mayring. The increasing digitalisation will have a large effect on the sales force, tasks will disappear, new tasks will be added and new ones will replace conventional working methods. In summary, automation will simply make tasks superfluous, software tools will improve quality and increase efficiency, and personal selling will become a premium skill. Companies will try to automate as many backoffice activities as possible and reduce the number of office staff if necessary. N2 - Im Laufe der Geschichte hat eine Vielzahl von Einflüssen die Art und Weise verändert, wie wir unsere Produkte verkaufen. Angefangen mit der industriellen Revolution bis hin zur ersten Sättigungsphase in den 1970er Jahren. Nun stellt sich die Frage, ob sich die Heizungsbranche mit der zunehmenden Digitalisierung des Vertriebs derzeit wieder auf einem evolutionären Entwicklungspfad befindet. Wie sich der Verkaufsprozess im B2B-Bereich mit zunehmender Digitalisierung verändern wird und welche Auswirkungen dies auf das Verkaufspersonal haben wird, ist nur durch wenige Quellen dokumentiert, die keine Rückschlüsse auf das Handwerk oder gar die Heizungsbranche zulassen. Daraus ergibt sich eine Forschungslücke, die im Rahmen dieser Arbeit geschlossen werden soll. Ziel dieses Forschungsprojektes ist es, die Auswirkungen einer weiteren Digitalisierung des Vertriebsprozesses auf den Außendienst im definierten Umfeld der Heizungsbranche in Mitteleuropa zu ermitteln. Dazu werden die folgenden Forschungsfragen gestellt: Welche Schritte des Vertriebsprozesses in der Heizungsbranche in Mitteleuropa sollten digitalisiert werden? Welche Auswirkungen hat die Digitalisierung des Vertriebsprozesses auf den Außendienst der Heizungsbranche in Mitteleuropa? Als Untersuchungsmethode wurde eine Fallstudie nach Yin gewählt. Die Daten wurden mit Hilfe von Tiefeninterviews erhoben und qualitativ nach Mayring analysiert. Die zunehmende Digitalisierung wird große Auswirkungen auf den Außendienst haben, Aufgaben werden verschwinden, neue Aufgaben kommen hinzu und herkömmliche Arbeitsmethoden werden ersetzt. Zusammenfassend lässt sich sagen, dass die Automatisierung einfach Aufgaben überflüssig machen wird, dass Software-Tools die Qualität verbessern und die Effizienz steigern werden und dass der persönliche Verkauf zu einer Premium-Fähigkeit wird. Die Unternehmen werden versuchen, so viele Back-Office-Tätigkeiten wie möglich zu automatisieren und gegebenenfalls die Zahl der Büroangestellten zu reduzieren. T2 - Auswirkungen der Digitalisierung von Verkaufsprozessen auf den Außendienst im B2B-Umfeld : eine Fallstudie am Beispiel der Heizungsbranche in Mitteleuropa KW - Digitalisation KW - Sales processes KW - Sales force KW - Heating industry Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3702 ER - TY - THES A1 - Malkoc, Elvir T1 - The power of the end-users for B2B influencer marketing BT - a practical case study in the tools and hardware industry N2 - Influencer Marketing has been discussed by various marketing experts for years and is already a fixed component of the marketing strategy in many companies. These are mainly companies from the B2C sector. Recently, more and more companies are asking themselves about possible areas of application within the B2B structure. This phenomenon is influenced by the increase in digitalization and the ever-higher hurdles in reaching target groups using traditional marketing tools. The topic of this master’s thesis was the result of professional and personal development. Various modules attended during the study inspired a deeper interest in the subject. Furthermore, the topic was always a point of discussion in the professional environment, resulting in the realisation that there is currently very little knowledge in B2B companies regarding Influencer Marketing. The aim of the research was to discover how to systematically find end users for the use of Influencer Marketing in B2B companies in the tool and hardware industry. Furthermore, the success factors for a long-term cooperation between influencers and companies from this industry will be identified and presented. Research questions were created in order to realise the above-mentioned objectives. Therefore, the primary research question and three sub-research questions were created for both the theoretical and empirical part of the work. To answer these questions, eight experts from B2B companies in the tool and hardware industry were interviewed. The evaluation was based on the qualitative content analysis according to Mayring. From the research results, a possible selection procedure could be identified, which would enable companies to systematically select influencers for marketing purposes. Furthermore, success criteria for a long-term cooperation between influencers and companies were also identified. N2 - Influencer Marketing wird seit Jahren von verschiedenen Marketingexperten diskutiert und ist in vielen Unternehmen bereits fester Bestandteil der Marketingstrategie. Dies sind vor allem Firmen aus dem B2C-Bereich. In letzter Zeit stellen sich deshalb immer mehr Marketer die Frage nach möglichen Einsatzbereichen in verschiedenen B2B-Unternehmen. Dieses Phänomen wird nicht zuletzt durch die zunehmende Digitalisierung und immer höhere Hürden bei der Ansprache von Zielgruppen mit klassischen Marketinginstrumenten verursacht. Das Thema der Masterarbeit war das Ergebnis einer beruflichen und privaten Entwicklung. Verschiedene Lehreinheiten, die während des Studiums besucht wurden, bildeten die Grundlage für ein erhöhtes Interesse an der Thematik Influencer Marketing. Zudem war das Thema immer auch Gegenstand von Diskussionen im beruflichen Umfeld. Es stellte sich jedoch heraus, dass in B2B-Unternehmen derzeit kaum Wissen über Influencer Marketing vorhanden ist. Ziel der Untersuchung war es, herauszufinden, wie man systematisch Endnutzer für den Einsatz von Influencer Marketing in B2B-Unternehmen der Werkzeug- und Eisenwarenindustrie finden kann. Weiterhin sollte dargestellt werden, was die Erfolgsfaktoren für eine langfristige Zusammenarbeit zwischen Influencer und Unternehmen aus dieser Branche sind. Es wurden Forschungsfragen erstellt, um die oben genannten Ziele herauszufinden. Daher wurden für den theoretischen und empirischen Teil der Arbeit eine Hauptforschungsfrage und drei Unterforschungsfragen definiert. Zur Beantwortung dieser Fragen wurden acht Experten aus B2B-Unternehmen der Werkzeug- und Eisenwarenindustrie befragt. Die Auswertung basierte auf der qualitativen Inhaltsanalyse nach Mayring. Aus den Forschungsergebnissen konnte ein mögliches Auswahlverfahren dargestellt werden, das es den Marketingmanagern ermöglicht, Influencer für Marketingzwecke systematisch auszuwählen. Darüber hinaus konnten auch Erfolgskriterien für eine langfristige Zusammenarbeit zwischen Influencern und Unternehmen beschrieben werden. T2 - Die Macht der Endanwender im B2B Influencer Marketing KW - Marketing KW - Influencer KW - Influencer marketing KW - Business-to-Business Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3723 ER - TY - THES A1 - Frick, Anabel T1 - Predictive maintenance BT - Abgleich der Situation in Vorarlberger Unternehmen mit dem Stand der Forschung N2 - Das Ziel dieser Arbeit ist es aufzuzeigen, wie Predictive Maintenance in Vorarlberger Unternehmen verbreitet ist und wie sich dies mit dem aktuellen Stand der Forschung deckt. Dazu werden die folgenden Forschungsfragen gestellt: Wie ist der aktuelle Stand der Forschung auf dem Gebiet Predictive Maintenance? Wie deckt sich der Stand der Forschung im Bereich Predictive Maintenance mit der Verbreitung in Vorarlberger Unternehmen? Um die erste Forschungsfrage zu beantworten, wurde eine Literaturrecherche und -analyse durchgeführt. Um die zweite Forschungsfrage zu beantworten, wurden zwölf Interviews mit Vorarlberger Unternehmen durchgeführt. Die Ergebnisse der qualitativen Forschung wurden mit den Erkenntnissen aus der Literatur verglichen. Predictive Maintenance wird in Vorarlberger Unternehmen noch nicht oft angewendet. Die qualitative Forschung hat gezeigt, dass vor allem Engineering-Unternehmen ein Interesse am Einsatz von Predictive Maintenance habe, da sie damit ihre Produkte verbessern und Wartungskosten senken können. Produktionsunternehmen haben ein weniger starkes Interesse an der Umsetzung von Predictive Maintenance. N2 - The aim of this thesis is to show how predictive maintenance is spread in companies located in Vorarlberg and how this corresponds to the current state of research. The following research questions are asked: What is the current state of research in the field of predictive maintenance? How does the current state of research in the field of predictive maintenance coincide with the distribution in companies located in Vorarlberg? To answer the first research question, a literature research and analysis was carried out. To answer the second research question, twelve interviews were conducted with companies located in Vorarlberg. The results of the qualitative research were compared with the findings from the literature. Predictive maintenance is not yet often applied in companies located in Vorarlberg. The qualitative research has shown that engineering companies in particular are interested in the use of predictive maintenance, as it enables them to improve their products and reduce maintenance costs. Production companies are less interested in the implementation of pre-dictive maintenance. T2 - Predictive maintenance : comparison of the situation in companies located in Vorarlberg with the state of research KW - Predictive maintenance KW - Prädiktive Wartung KW - Vorausschauende Instandhaltung KW - Prädiktive Instandhaltung KW - Vorausschauende Wartung Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3712 ER - TY - THES A1 - Arzbacher, Stefan T1 - Micro-computed tomography of growth and decomposition of clathrate hydrates BT - time-lapse non-destructive imaging of gas hydrates on the mesoscopic scale N2 - Clathrate hydrates, or hydrates for short, are inclusion compounds in which water molecules form a hydrogen-bonded host lattice that accommodates the guest molecules. While vast amounts of hydrates are known to exist in seafloor sediments and in the permafrost on Earth, these occurrences might be dwarfed by the amounts of hydrates occurring in space and on celestial bodies. Since methane is the primary guest molecule in most of the natural occurrences on Earth, hydrates are considered a promising source of energy. Moreover, the ability of one volume of hydrate to store about 170 volumes of gas, make hydrates a promising functional material for various industrial applications. While the static properties of hydrates are reasonably well known, the dynamics of hydrate formation and decomposition are insufficiently understood. For instance, the stochastic period of hydrate nucleation, the memory effect, and the self-preservation phenomenon complicate the development of predictive models of hydrate dynamics. Additionally, the influence of meso- and macroscopic defects as well as the roles of mass and heat transport on different length scales remain to be clarified. Due to its non-invasive and non-destructive nature and the high spatial resolution of approx. 1µm or even less, micro-computed X-ray attenuation tomography ( µCT ) seems to be the perfect method for the study of the evolving structures of forming or decomposing hydrates on the meso- and macroscopic length scale. However, for the naturally occurring hydrates of low atomic number guests the contrast between hydrate, ice, and liquid water is typically very weak because of similar X-ray attenuation coefficients. So far, good contrast was only restricted to synchrotron beamline experiments which utilize the phase information of monochromatic X-rays. In this thesis it is shown that with the help of a newly developed sample cell, a contrast between the hydrate and the ice phase sufficiently good for the reliable segmentation of the materials can also be achieved in conventional tube-based µCT . An accurate pressure and temperature management, i.e., the added functionality of the cell, further allows for cross-correlation of structural and thermodynamic data. The capability of this µCT setup is demonstrated in a series of studies on the formation and decomposition of hydrates which yield new insights for the development of a novel route to hydrate synthesis. At last, this thesis points towards possibilities how better models of hydrate formation and decomposition can be developed with the aid of µCT and computer simulations. KW - Computed tomography KW - Clathrate hydrates Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3805 ER - TY - RPRT A1 - Dobler, Martin A1 - Schumacher, Jens A1 - Kurth, Marcus A1 - Schleyer, Carsten A1 - Prenzler, Jürgen A1 - Piai, Guido A1 - Wüst, Markus A1 - Selm, Bärbel T1 - Internationale Musterfabrik Industrie 4.0 BT - i4Production. Wie KMU ihre Produktion zukunftssicher, effizient und produktiv gestalten können N2 - Wer wünscht ihn nicht: den intelligenten, effizienten und wirtschaftlichen Herstellungsprozess? Viele Firmen setzten aktuell auf die Digitalisierung und verbessern so die eigene sowie die mit externen Stellen vernetzte Produktion. Die Digitalisierung bringt einerseits Fortschritt, zeigt aber auch die zunehmende Komplexität der heutigen Produktionsnetzwerke auf. Zahlreiche Entscheidungen sind zu fällen, um einen effizienten und sicheren Austausch mit verschiedenen Betrieben zu gewährleisten. Ein Blick auf vorhandene Modelle kann da weiterhelfen: Im Projekt i4Production des IBH-Labs KMUdigital haben Teams an drei Standorten in den drei Nachbarländern Deutschland (HTWG Konstanz), Österreich (FH Vorarlberg) und der Schweiz (NTB Buchs, RhySearch) an einer vernetzten Prozesslandschaft gearbeitet. In einem gemeinsamen, standardisierten Automatisierungskonzept wird in der international vernetzten Modellfabrik ein cyberphysisches System (CPS) in Form eines kundenindividualisierten Modellfahrzeuges produziert, das durch den Kunden in diversen Varianten zusammengestellt oder individuell konstruiert werden kann. Die dezentrale Produktion erlaubt eine Datenweitergabe über die Landesgrenzen in Echtzeit und bildet die Simulation eines länderübergreifenden Business-Eco-Systems ab. Die Erkenntnisse des Projekts i4Production zeigen wie in kleineren und mittleren Unternehmen (KMU) eine verteilte Produktion, inklusive der Einbindung von Mitarbeitenden und Kunden in eine digitalisierte, hochautomatisierte und kundenindividuelle Produktion, organisiert werden kann. Für Unternehmen wird diese Industrie 4.0-Prozesslandschaft als Modell für die eigene Fertigung in dem neu aufgebauten CNC Präzisionsfertigungslabor „Werkstatt4“ bei RhySearch öffentlich zur Verfügung gestellt. Die „Werkstatt4“ bietet KMU ein digitales Prozessumfeld, in dem getestet werden kann, mit welchen Maßnahmen der eingangs gestellte Wunsch zur optimierten Herstellung, seinen Weg in die Realität finden kann. Im Folgenden stellen wir Ihnen das Konzept der internationalen Musterfabrik i4Production, die diversen Arbeitsschritte an den beteiligten Hochschulen sowie die wichtigsten Erkenntnisse für KMU der Bodenseeregion vor. Gerne unterstützen wir Sie bei der Gestaltung des Wandels hin zum Unternehmen 4.0: Sprechen Sie uns an. Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3799 PB - Internationale Bodenseehochschule Labs CY - Kreuzlingen ER - TY - JOUR A1 - Thaler, Jonathan A1 - Siebers, Peer-Olaf T1 - Specification testing of agent-based simulation using property-based testing JF - Autonomous Agents and Multi-Agent Systems N2 - The importance of Agent-Based Simulation (ABS) as scientific method to generate data for scientific models in general and for informed policy decisions in particular has been widely recognised. However, the important technique of code testing of implementations like unit testing has not generated much research interested so far. As a possible solution, in previous work we have explored the conceptual use of property-based testing. In this code testing method, model specifications and invariants are expressed directly in code and tested through automated and randomised test data generation. This paper expands on our previous work and explores how to use property-based testing on a technical level to encode and test specifications of ABS. As use case the simple agent-based SIR model is used, where it is shown how to test agent behaviour, transition probabilities and model invariants. The outcome are specifications expressed directly in code, which relate whole classes of random input to expected classes of output. During test execution, random test data is generated automatically, potentially covering the equivalent of thousands of unit tests, run within seconds on modern hardware. This makes property-based testing in the context of ABS strictly more powerful than unit testing, as it is a much more natural fit due to its stochastic nature. KW - Agent-based simulation testing KW - Code testing KW - Test driven development KW - Model specification Y1 - 2020 U6 - http://dx.doi.org/10.1007/s10458-020-09473-8 SN - 1387-2532 SN - 1573-7454 VL - 34. Jg. IS - H. 2/47 ER - TY - RPRT A1 - Finck, Steffen T1 - Zusammenfassung der Forschungsarbeiten. Josef Ressel Zentrum für angewandtes wissenschaftliches Rechnen in Energie, Finanzwirtschaft und Logistik Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3798 PB - FH Vorarlberg CY - Dornbirn ER - TY - JOUR A1 - Ager, Clemens A1 - Mochalski, Pawel A1 - King, Julian A1 - Mayhew, Chris A A1 - Unterkofler, Karl T1 - Effect of inhaled acetone concentrations on exhaled breath acetone concentrations at rest and during exercise JF - Journal of Breath Research N2 - Real-time measurements of the differences in inhaled and exhaled, unlabeled and fully deuterated acetone concentration levels, at rest and during exercise, have been conducted using proton transfer reaction mass spectrometry. A novel approach to continuously differentiate between the inhaled and exhaled breath acetone concentration signals is used. This leads to unprecedented fine grained data of inhaled and exhaled concentrations. The experimental results obtained are compared with those predicted using a simple three compartment model that theoretically describes the influence of inhaled concentrations on exhaled breath concentrations for volatile organic compounds with high blood:air partition coefficients, and hence is appropriate for acetone. An agreement between the predicted and observed concentrations is obtained. Our results highlight that the influence of the upper airways cannot be neglected for volatiles with high blood:air partition coefficients, i.e. highly water soluble volatiles. Y1 - 2020 U6 - http://dx.doi.org/10.1088/1752-7163/ab613a SN - 1752-7163 VL - 14. Jg. IS - H. 2/026010 ER - TY - CHAP A1 - Dobler, Martin A1 - Büsel, Philipp A1 - Hartmann, Christian A1 - Schumacher, Jens T1 - Supporting SMEs in the Lake Constance region in the implementation of cyber-physical-systems BT - framework and demonstrator T2 - 2020 IEEE International Conference on Engineering, Technology and Innovation (ICE/ITMC) N2 - With the emergence of the recent Industry 4.0 movement, data integration is now also being driven along the production line, made possible primarily by the use of established concepts of intelligent supply chains, such as the digital avatars. Digital avatars – sometimes also called Digital Twins or more broadly Cyber-Physical Systems (CPS) – are already successfully used in holistic systems for intelligent transport ecosystems, similar to the use of Big Data and artificial intelligence technologies interwoven with modern production and supply chains. The goal of this paper is to describe how data from interwoven, autonomous and intelligent supply chains can be integrated into the diverse data ecosystems of the Industry 4.0, influenced by a multitude of data exchange formats and varied data schemas. In this paper, we describe how a framework for supporting SMEs was established in the Lake Constance region and describe a demonstrator sprung from the framework. The demonstrator project’s goal is to exhibit and compare two different approaches towards optimisation of manufacturing lines. The first approach is based upon static optimisation of production demand, i.e. exact or heuristic algorithms are used to plan and optimise the assignment of orders to individual machines. In the second scenario, we use real-time situational awareness – implemented as digital avatar – to assign local intelligence to jobs and raw materials in order to compare the results to the traditional planning methods of scenario one. The results are generated using event-discrete simulation and are compared to common (heuristic) job scheduling algorithms. KW - Cyber-Physical Systems KW - Simulation KW - Industry 4.0 KW - Self-Organisation Y1 - 2020 SN - 978-1-7281-7037-4 U6 - http://dx.doi.org/10.1109/ICE/ITMC49519.2020.9198430 PB - IEEE ER - TY - CHAP A1 - Suzic, Bojana A1 - Ulmer, Annette A1 - Schumacher, Jens T1 - Complementarities and synergies of quadruple helix innovation design in smart city development T2 - 2020 Smart City Symposium Prague (SCSP) N2 - Increased urbanization trends are stimulating regional needs to support transitions from urban environments to smart cities, using its holistic perspective as a source to innovation. Strong relations between smart cities, urban and regional development, are getting increased attention both at policy and implementation level, providing fertile ground for execution of the new European policy frameworks that supports quadruple helix approaches to innovation. Smart specialization strategies (RIS3) encompass such initiatives, placing ICT and collaboration between academia, industry, government, and citizen at the center of urban innovation. However, there is still lack of research on effects of such approaches to innovation, involving both quadruple helix clusters and ICT in utilizing innovation potentials for developing smart cities. This study aims to increase the understanding on how quadruple helix urban innovation strengthens competitiveness of regions by improving its local smart areas – RIS3. We identified smart specialization patterns and applied comparative benchmark between nine smallmedium sized urban regions in Central Europe. Building on these results, the study provides an overview of the effects of RIS3 strategies implemented through quadruple helix innovation clusters on competitiveness of regions and Smart City development. KW - Smart cities KW - Quadruple helix clusters KW - Open innovation KW - Smart specialization KW - Urban innovation Y1 - 2020 SN - 978-1-7281-6821-0 U6 - http://dx.doi.org/10.1109/SCSP49987.2020.9133961 PB - IEEE ER - TY - CHAP A1 - Hellwig, Michael A1 - Beyer, Hans-Georg T1 - A modified matrix adaptation evolution strategy with restarts for constrained real-world problems T2 - 2020 IEEE Congress on Evolutionary Computation (CEC) N2 - In combination with successful constraint handling techniques, a Matrix Adaptation Evolution Strategy (MA-ES) variant (the εMAg-ES) turned out to be a competitive algorithm on the constrained optimization problems proposed for the CEC 2018 competition on constrained single objective real-parameter optimization. A subsequent analysis points to additional potential in terms of robustness and solution quality. The consideration of a restart scheme and adjustments in the constraint handling techniques put this into effect and simplify the configuration. The resulting BP-εMAg-ES algorithm is applied to the constrained problems proposed for the IEEE CEC 2020 competition on Real-World Single-Objective Constrained optimization. The novel MA-ES variant realizes improvements over the original εMAg-ES in terms of feasibility and effectiveness on many of the real-world benchmarks. The BP-εMAg-ES realizes a feasibility rate of 100% on 44 out of 57 real-world problems and improves the best-known solution in 5 cases. KW - Optimization KW - Constraints KW - Evolutionary algorithms Y1 - 2020 SN - 978-1-7281-6929-3 U6 - http://dx.doi.org/10.1109/CEC48606.2020.9185566 PB - IEEE ER - TY - JOUR A1 - Hebertinger, Martin A1 - Gehrig, Marco A1 - Sedlarik, Lenka T1 - Key Performance Indicators bei börsenkotierten Unternehmen BT - eine aktuelle Praxiserhebung JF - Zeitschrift für Internationale Rechnungslegung N2 - Steigende Komplexität von Geschäftsmodellen und in der Niedrigzinsphase stets zulegende Renditeerwartungen an kapitalmarktorientierte Unternehmen führen dazu, dass sich deren Berichterstattung anpasst. Unter anderem ist eine verstärkte Verbreitung und Anwendung von Key Performance Indicators (alternative Führungsgrößen) in der Praxis zu beobachten. Wenigen, zwar prägnanten, aber eben nicht einheitlich definierten oder gar nach geltenden Rechnungslegungsnormen objektiv zu gewinnende Messgrößen kommt eine gesteigerte Bedeutung im externen Berichtswesen zu. Der Beitrag liefert eine Bestandesaufnahme der meist verwendeten Key Performance Indicators in der Praxis in Deutschland, in Österreich und in der Schweiz. KW - Free cashflow KW - EBIT KW - EBITDA KW - alternative Performancekennzahlen KW - Key performance indicators (KPIs) Y1 - 2020 VL - 15. Jg. IS - H. 10 SP - 457 EP - 460 ER - TY - JOUR A1 - Kuckert-Wöstheinrich, Andrea A1 - Deselaers, Christina T1 - Implikationen aus einem Flüchtlingsprojekt für die Praxisanleitung in der Pflege JF - Die Praxisanleitung Y1 - 2020 VL - 1. Jg. IS - H. 3 SP - 20 EP - 25 ER - TY - THES A1 - Bosse, Tobias T1 - Conception and prototypical realization of a machine learning algorithm for the annotation of time series N2 - Many test drives are carried out in the automotive environment. During these test drives many signals are recorded. The task of the test engineers is to find certain patterns (e.g. an emergency stop) in these long time series. Finding these interesting patterns is currently done with rule based processing. This procedure is very time consuming and requires a test engineer with expertise. In this thesis it is examined if the emerging field of machine learning can be used to support the engineers in this task. Active Learning, a subarea of machine learning, is used to train a classifier during the labeling process. Thereby it proposes similar windows to the already labeled ones. This saves the annotator time for searching or formulating rules for the problem. A data generator is worked out to replace the missing labeled data for tests. The custom performance measure “proportion of seen samples” is developed to make the success measurable. A modular software architecture is designed. With that, several combinations of Time Series Classification algorithms and query strategies are compared on artificial data. The results are verified on real datasets, which are open source available. The best performing, but computational intensive solution is an adapted RandOm Convolutional KErnel Transform (ROCKET). The custom query strategy “certainty sampling” shows the best results for highly imbalanced datasets. N2 - Im Automobilbereich werden viele Testfahrten durchgeführt. Während dieser Testfahrten werden zahlreiche Signale aufgezeichnet. Die Aufgabe der Versuchsingenieure ist es, in diesen langen Zeitreihen bestimmte Strukturen (z.B. eine Notbremsung) zu finden. Das Auffinden dieser Strukturen wird derzeit mit regelbasierten Signalverbeitungen realisiert. Dieses Verfahren ist sehr zeitaufwendig und erfordert Experten mit Fachwissen. In dieser Arbeit wird untersucht, ob das aufstrebende Gebiet des maschinellen Lernens genutzt werden kann, um die Ingenieure bei dieser Aufgabe zu unterstützen. Aktives Lernen, ein Teilbereich des maschinellen Lernens, wird genutzt, um einen Klassifikator während des Annotierungsprozesses zu trainieren. Dabei schlägt es ähnliche Fenster zu den bereits annotierten vor. Dies erspart dem Annotator Zeit für die Suche oder die Formulierung von Regeln für das Problem. Es wird ein Datengenerator entwickelt, der die fehlenden annotierten Daten für Tests ersetzt. Um den Erfolg messbar zu machen, wird das eigene performance-Maß "Anteil der gesehenen samples" entwickelt. Eine modulare Software-Architektur wird entwickelt. Damit werden mehrere Kombinationen von Zeitreihen-Klassifikationsalgorithmen und Suchstrategien auf den künstlichen Daten verglichen. Die Ergebnisse werden an realen Datensätzen, die Open Source verfügbar sind, verifiziert. Die leistungsstärkste, aber rechenintensive Lösung ist eine angepasste RandOm Convolutional KErnel Transform. Die eigens definierte Suchstrategie “certainty sampling” zeigt die besten Ergebnisse für stark unausgewogene Datensätze. KW - Machine learning Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3695 ER - TY - THES A1 - Schürer, Albert T1 - Pump-Probe-Elastographie BT - Untersuchung des Einflusses der Pulsenergie auf die Ausbreitungsgeschwindigkeit und Detektierbarkeit akustischer Wellen N2 - Krebs ist die zweit häufigste Todesursache in Deutschland. Seine frühzeitige Detektion ist wichtig für eine erfolgreiche Behandlung. Die Detektion und Charakterisierung der Tumore kann unter anderem anhand ihrer mechanischen Eigenschaften erfolgen. Die Pump-Probe-Elastographie (PPE) ist eine neue und vielversprechende Methode um die mechanischen Eigenschaften von Gewebe durch optische Anregung und Detektion der dadurch entstehenden akustischen Wellen zu charakterisieren. In dieser Arbeit wurde ein PPE-Mikroskop aufgebaut und anschließend untersucht, wie die Wellenfronten möglichst deutlich sichtbar werden und welchen Einfluss die Pulsenergie auf die erzeugten Wellen hat. Dies geschah anhand zweier Proben – Wasser und Glas. Beide sind transparent und bieten daher auch die Möglichkeit der Messung im Volumen. Wasser unterscheidet sich zudem von Glas, da es kompressibel ist und somit die Entstehung von Stoßwellen erlaubt. In Glas wiederum können nicht nur Longitudinalwellen, sondern auch Transversalwellen und Rayleigh-Wellen entstehen. Als Ergebnis dieser Arbeit wird gezeigt, dass die Messergebnisse in Wasser abhängig von der Pulsenergie sind, denn die entstehenden Stoßwellen breiten sich mit Überschallgeschwindigkeit aus, was bei zukünftigen Messungen mit Zellgewebe zu beachten ist. In Glas hat die Pulsenergie zwar keinen Einfluss auf die Wellengeschwindigkeit, jedoch werden die Messungen mit zunehmender Energie deutlicher. Auch ist bei Messungen im Volumen nur die Longitudinalwelle zu sehen. Misst man jedoch auf der Glasoberfläche, so entsteht auch eine Druckwelle in der Luft, welche wiederum abhängig von der Pulsenergie ist. Zusätzlich ist in einigen Messungen eine weitere Welle zu erkennen, welche unabhängig von der Pulsenergie ist und sich im Glas, oder auf dessen Oberfläche ausbreitet. N2 - Cancer is the second most frequent cause of death in Germany. Its early detection is important for successful treatment. The detection and characterization of tumors can be based on their mechanical properties. The PPE is a new and promising method to characterize the mechanical properties of tissue by optical stimulation and detection of the resulting acoustic waves. In this thesis, a PPE microscope was set up. Subsequently, it was investigated how the wave fronts become visible as clearly as possible and how the pulse energy influences the generated waves. This was done with two samples – water and glass. Both are transparent and therefore offer the possibility to measure in their volumes. Water also differs from glass because it is compressible and allows the development of shock waves. In glass, not only longitudinal waves but also transverse and Rayleigh waves can be generated. As a result of this thesis it is shown that the measured results in water depend on the pulse energy.The resulting shock waves propagate at supersonic speed, which has to be considered for future measurements with cell tissues. The pulse energy has no influence on the wave velocity in glass, but the measurements become clearer with increasing energy. When measuring inside the volume, only the longitudinal wave is visible. However, if the excitation of the waves takes place on the glass surface, a pressure wave is also generated in the air, which in turn depends on the pulse energy. In addition, some measurements show another wave, which is independent of the pulse energy and propagates inside glass or on its surface. T2 - Pump-Probe-Elastography : investigation of the influence of pulse energy on the propagation speed and detectability of acoustic waves KW - Pump-Probe-Elastographie KW - Pump-Probe-Elastography Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3683 ER - TY - JOUR A1 - Malásková, Michaela A1 - Olivenza-León, David A1 - Chellayah, Prema D. A1 - Martini, Judith A1 - Lederer, Wolfgang A1 - Ruzsanyi, Veronika A1 - Unterkofler, Karl A1 - Mochalski, Paweł A1 - Märk, Tilmann D. A1 - Watts, Peter A1 - Mayhew, Chris A. T1 - Studies pertaining to the monitoring of volatile halogenated anaesthetics in breath by proton transfer reaction mass spectrometry JF - Journal of Breath Research N2 - Post-operative isoflurane has been observed to be present in the end-tidal breath of patients who have undergone major surgery, for several weeks after the surgical procedures. A major new noncontrolled, non-randomized, and open-label approved study will recruit patients undergoing various surgeries under different inhalation anaesthetics, with two key objectives, namely to record the washout characteristics following surgery, and to investigate the influence of a patient’s health and the duration and type of surgery on elimination. In preparation for this breath study using proton transfer reaction time-of-flight mass spectrometry (PTR-TOF-MS), it is important to identify first the analytical product ions that need to be monitored and under what operating conditions. In this first paper of this new research programme, we present extensive PTR-TOF-MS studies of three major anaesthetics used worldwide, desflurane (CF3CHFOCHF2), sevoflurane ((CF3)2CHOCH2F), and isoflurane (CF3CHClOCHF2) and a fourth one, which is used less extensively, enflurane (CHF2OCF2CHFCl), but is of interest because it is an isomer of isoflurane. Product ions are identified as a function of reduced electric field (E/N) over the range of approximately 80 Td to 210 Td, and the effects of operating the drift tube under ‘normal’ or ‘humid’ conditions on the intensities of the product ions are presented. To aid in the analyses, density functional theory (DFT) calculations of the proton affinities and the gas-phase basicities of the anaesthetics have been determined. Calculated energies for the ion-molecule reaction pathways leading to key product ions, identified as ideal for monitoring the inhalation anaesthetics in breath with a high sensitivity and selectivity, are also presented. KW - PTR-ToF-MS KW - Anaesthetics KW - Halogenated ethers KW - Pharmacokinetics KW - Isoflurane Y1 - 2020 U6 - http://dx.doi.org/10.1088/1752-7163/ab5e30 SN - 1752-7163 VL - 14. Jg. IS - H. 2/026004 ER - TY - THES A1 - Abelein, Beat Dominik T1 - Characterisation and manufacturing of glass fibre diffuser with ultrashort pulse laser N2 - In recent years, much research has been done on medical laser applications inside the human body, as they are minimally invasive and therefore have fewer side effects and are less expensive than conventional therapies. In order to bring the laser light into the human body, a glass fibre with a diffuser is needed. The goal of this master thesis is the characterization and production of fibre optic diffusers that can be used for the three therapeutic applications: photodynamic therapy, laser-induced thermotherapy and endovenous laser therapy. For this purpose the following goals have to be achieved: - Optimization of the efficiency and homogeneity of internally structured diffusers - Examine damage thresholds of the diffusers in the tissue using a crash test - Achieving a better understanding of the decouple mechanism with a simulation Using an ultra-short pulse laser, modifications could be introduced into the fibre in this way that the radiation profile is homogeneous and the decoupling efficiency is 68.3 %. It was discovered that the radiation profile depends on the wavelength. Attempts have been made to improve the decoupling efficiency by mirroring the distal end of the fibre. The mirror reflects the remaining light back into the fibre, so that it is also decoupled lateral on the modifications. Vapor-deposited aluminum with physical vapor deposition is a promising approach. However, the adhesion of the coating must be improved or the coating must be protected by a mechanical cover, otherwise it will flake off too quickly. In a crash test, it was shown that the glass fibre diffusers can withstand 20 W laser power for 300 s without visible change. In an ex vivo test, the coagulation zone in the tissue was examined and it was showed that the diffusers radiate radially homogeneously. Using a ray trace simulation, the course of the light rays in the fibre was examined and the correlation of modification width and length with the decoupling efficiency was investigated. It was discovered that there are helical light rays in the fibre, which cannot be decoupled by modifications in the fibre centre. KW - Photodynamic therapy KW - Diffuser Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3659 ER - TY - THES A1 - Schwartze, Nicolai T1 - Computational intelligence methods for solving partial differential equations BT - an experimental study on performance and accuracy N2 - This master thesis investigates a Computational Intelligence-based method for solving PDEs. The proposed strategy formulates the residual of a PDE as a fitness function. The solution is approximated by a finite sum of Gauss kernels. An appropriate optimisation technique, in this case JADE, is deployed that searches for the best fitting parameters for these kernels. This field is fairly young, a comprehensive literature research reveals several past papers that investigate similar techniques. To evaluate the performance of the solver, a comprehensive testbed is defined. It consists of 11 different Poisson equations. The solving time, the memory consumption and the approximation quality are compared to the state of the art open-source Finite Element solver NGSolve. The first experiment tests a serial JADE. The results are not as good as comparable work in the literature. Further, a strange behaviour is observed, where the fitness and the quality do not match. The second experiment implements a parallel JADE, which allows to make use of parallel hardware. This significantly speeds up the solving time. The third experiment implements a parallel JADE with adaptive kernels. It starts with one kernel and introduce more kernels along the solving process. A significant improvement is observed on one PDE, that is purposely built to be solvable. On all other testbed PDEs the quality-difference is not conclusive. The last experiment investigates the discrepancy between the fitness and the quality. Therefore, a new kernel is defined. This kernel inherits all features of the Gauss kernel and extends it with a sine function. As a result, the observed inconsistency between fitness and quality is mitigated. The thesis closes with a proposal for further investigations. The concepts here should be reconsidered by using better performing optimisation algorithms from the literature, like CMA-ES. Beyond that, an adaptive scheme for the collocation points could be tested. Finally, the fitness function should be further examined. N2 - Diese Masterarbeit untersucht eine Computational Intelligence Methode zum Lösen von PDEs. Diese Strategie formuliert das Residuum der PDE als Fitnessfunktion. Die Lösung wird durch eine endliche Summe von Gauß-Kernel approximiert. Ein geeigneter Optimierungsalgorithmus, in diesem Fall JADE, sucht die passenden Parameter für diese Kernel. Dieses Forschungsfeld ist relativ neu, eine umfassende Literaturrecherche zeigt mehrere Paper, die ähnliche Algorithmen behandeln. Um die Performance des Solvers zu bewerten, wird ein Testbed definiert. Es besteht aus 11 verschiedenen Poisson-Gleichungen. Die Lösungszeit, der Speicherbedarf und die Approximationsqualität werden mit dem open-source Finite Elemente Solver NGSolve verglichen. Das erste Experiment testet eine serielle JADE. Die Ergebnisse sind nicht so gut wie vergleichbare Arbeiten in der Literatur. Weiterhin wird ein Verhalten beobachtet, bei dem Fitness und Qualität nicht übereinstimmen. Das zweite Experiment implementiert eine parallele JADE. Somit kann parallele Hardware genutzt werden. Dadurch wird die Lösungsdauer erheblich verkürzt. Das dritte Experiment implementiert eine parallele JADE mit adaptiven Kernels. Der Solver beginnt mit einem Kernel und führt weitere Kernels während des Lösungsprozesses ein. Eine signifikante Verbesserung wird bei einer PDE beobachtet, die speziell dafür ausgelegt wurde. Bei allen anderen Testbed-PDEs ist der Qualitätsunterschied nicht aufschlussreich. Das letzte Experiment untersucht die Diskrepanz zwischen Fitness und Qualität. Dazu wird ein neuer Kernel definiert. Dieser Kernel hat alle Eigenschaften des Gauß-Kernels. Zusätzlich wird er mit einer Sinusfunktion erweitert. Dadurch werden die beobachteten Unterschiede zwischen Fitness und Qualität verringert. In weiterführenden Arbeiten sollten die hier eingeführten Konzepte mit anderen Optimierungsalgorithmen, wie zum Beispiel einer CMA-ES, überprüft werden. Darüber hinaus könnte ein adaptiver Prozess für die Collocation Punkte getestet werden. Schließlich sollte die Fitnessfunktion weiter untersucht werden. T2 - Computational Intelligence Methoden zum Lösen partieller Differentialgleichungen KW - Partial-differential-equations KW - Optimisation-algorithms KW - Jade KW - Finite-element-methods KW - Computational-intelligence Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3693 ER - TY - THES A1 - Schwendinger, Martin T1 - Fog Computing-Framework für ressourcenbeschränkte Systeme N2 - Die cloud-basierte Verarbeitung von Datenströmen von IoT-Geräten ist aufgrund hoher Latenzzeiten für zeitkritische Anwendungen nur beschränkt möglich. Fog Computing soll durch Nutzung der Rechen- und Speicherkapazitäten von lokal vorhandenen Geräten eine zeitnahe Datenverarbeitung und somit eine Verringerung der Latenzzeit ermöglichen. In dieser Arbeit werden Anforderungen an ein Fog Computing-Framework erhoben, das die dynamische Zuweisung und Ausführung von Services auf ressourcen-beschränkten Geräten in einem lokalen Netzwerk zur dezentralen Datenverarbeitung ermöglicht. Zudem wird dieses Framework prototypisch für mehrere Transportkanäle, unterschiedliche Betriebssysteme und Plattformen realisiert. Dazu werden die Möglichkeiten der Skriptsprache Lua und des Kommunikationsmechanismus Remote Procedure Call genutzt. Das Resultat ist ein positiver Machbarkeitsnachweis für Fog Computing-Funktionalitäten auf ressourcenbeschränkten Systemen. Zudem werden eine geringere Latenz und eine Reduktion der Netzwerklast ermöglicht. N2 - Cloud-based processing of data streams from IoT devices is due to high latency limited for time-critical applications. Fog computing is intended to enable timely processing and thus optimize latency by utilizing the computing and storage capacities of locally available devices. In this thesis requirements for a fog computing framework are defined, which allows the dynamic allocation and execution of services on resource limited devices in a local network for decentralized data processing. In addition, this framework is prototypically realized for multiple transport channels, different operating systems and platforms. For this purpose, the possibilities of the scripting language Lua and remote procedure call as a communication mechanism are used. The result is a positive proof of concept for fog computing functionalities on resource-constrained systems. In addition, it enables a lower latency and a reduction of the network load. T2 - Fog computing framework for resource-constrained systems Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3721 ER - TY - THES A1 - Tomasini, Alexander T1 - Energieeffizienz in der Warmwasserbereitung BT - Vergleich von dezentralen Systemen zur Warmwasserbereitung in Wohngebäuden N2 - Die vorliegende Arbeit befasst sich mit der Untersuchung von dezentralen Warmwasserbereitungssystemen, wobei der Fokus auf Energieeffizienz liegt. Als Vergleichs- und Referenzobjekt wird das Wohngebäude „KliNaWo“ mit 19 Wohneinheiten am Standort Feldkirch herangezogen, in welchem eine zentrale Warmwasserbereitung realisiert wurde. Als ersten Schritt werden die theoretischen Grundlagen hinsichtlich der zentralen und dezentralen Warmwasserbereitungs-systeme sowie der unterschiedlichen Wärmeerzeuger, Speichertechnologien und Verteilsysteme erarbeitet. Anschließend erfolgt eine Erläuterung der aktuellen Normensituation und den wichtigsten Fakten bezüglich Trinkwasserhygiene. Des Weiteren wird das Referenzobjekt „KliNaWo“ sowie die verwendeten Messdaten zur Kalibrierung der Simulationsmodelle beschrieben. Im nachfolgenden Kapitel erfolgt eine detaillierte Darstellung der zu untersuchenden Systeme, wobei es sich um das Wohnungssatellitensystem sowohl mit kontinuierlicher Beladung als auch im Ladefensterbetrieb sowie um dezentrale Boiler-Wärmepumpen handelt. Anschließend wird die verwendete Simulationssoftware Polysun erläutert und erklärt wie die Systeme in der Software abgebildet und welche Ersatzmodelle angewendet werden. Die Nutzenergie in Bezug auf das Warmwasser beträgt bei der zentralen Variante 20.584 kWh und ist bei allen dezentralen Systemen mit 20.142 kWh etwas geringer, da die Verteilverluste der Warmwasser-Einzelleitungen aufgrund des niedrigeren Temperaturniveaus geringer ausfallen. Da die rückgewinnbaren Wärmeverluste berücksichtigt werden, ergeben sich auch für den Heizwärmebedarf in Abhängigkeit der Variante unterschiedliche Werte im Bereich von 54.322 kWh bis 58.104 kWh. Als Vergleichsgröße wird der gesamte Stromverbrauch der Wärmepumpen inklusive der Förderpumpen herangezogen, welcher für die Deckung des Heizwärmebedarfs, der Verluste sowie des Energiebedarfs bezüglich Warmwasser notwendig ist. Aus dem Vergleich der Varianten ergibt sich, dass der Stromverbrauch des zentralen Systems mit 14.109 kWh am geringsten ausfällt und das Wohnungssatellitensystem im Ladefensterbetrieb mit einem Strombedarf von 14.441 kWh nur wenig darüber liegt. Beim Wohnungssatellitensystem mit kontinuierlicher Beladung und bei den Boiler-Wärmepumpen-Systemen liegen die Stromverbräuche deutlich höher. Anhand der Simulationsergebnisse kann festgestellt werden, dass die dezentralen Anlagenkonfigurationen unter Berücksichtigung der ÖNROM B 2531 nicht effizienter sind als das zentrale System, wobei das Wohnungssatellitensystem im Ladefensterbetrieb in derselben Größenordnung wie das zentrale System liegt. Allerdings sind beim Wohnungssatellitensystem höhere Investitionskosten gegenüber der zentralen Variante zu erwarten, wodurch das System wirtschaftlich schlechter abschneidet. N2 - This master thesis refers to the investigation of decentralized domestic hot water systems focused on energy efficiency. The residential building "KliNaWo" in Feldkirch with 19 units, in which a central domestic hot water system was implemented, is used as comparison- and reference-object. As a first step, the theoretical principles regarding central and decentralized domestic hot water systems as well as the different heat generators, storage technologies and distribution systems will be developed. This is followed by an explanation of the current standards situation and the most important facts concerning drinking water hygiene. Furthermore, the reference-object "KliNaWo" and the measurement data, which are used to calibrate the simulation models, are described. In the following chapter a detailed description of the systems to be investigated is given. These are the residential satellite system with continuous loading and in charge window operation as well as decentralized boiler heat pumps. After that, the used simulation software Polysun is explained and declared how the systems are implemented in the software as well as which alternative models are used. The required energy in relation to domestic hot water is 20,584 kWh for the centralized system and somewhat lower for all decentralized systems at 20,142 kWh. The reason for this difference is the lower distribution losses of the single hot water pipes due to the lower temperature level. Because the recoverable heat losses are considered, different values in the range of 54,322 kWh to 58,104 kWh result for the heating demand depending on the variants. The total electricity consumption of the heat pumps including the feed pumps, which is necessary to cover the heating demand, losses and energy demand for domestic hot water, is used as a comparative figure. A comparison of the different variants shows that the electricity consumption of the central system is the lowest at 14,109 kWh and the residential satellite system in charge window operation is only slightly higher with an electricity requirement of 14,441 kWh. Electricity consumption is significantly higher for the residential satellite system with continuous loading and for boiler heat pump systems. On the basis of the simulation results, it can be concluded that the decentralized system configurations are not more efficient than the central system when ÖNROM B 2531 is considered, whereby the residential satellite system in charge window operation is in the same range as the central system. However, the investment costs for the residential satellite system are expected to be higher than for the centralized variant, which means that the system will be less cost-effective. T2 - Energy efficiency in domestic hot water preparation KW - dezentrale Warmwasserbereitung KW - Kombispeicher KW - Wohnungssatellitensystem KW - Boiler-Wärmepumpen KW - Energieeffizienz Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3708 ER - TY - THES A1 - Rüf, Markus T1 - Analyse von Optimierungspotentialen von elektrischen Prosumer-Haushalten mit E-Auto Nutzung, stationärem Batteriespeicher und exogener PV-Erzeugungs- und Lastprofile N2 - Mit dem entwickelten, gemischt-ganzzahligen linearen Optimierungsmodell wird ein grosser Beitrag geleistet, das die wichtigen Betriebskennzahlen einer PV-Speicheranlage, wie der Eigenverbrauchsanteil um bis zu 89 % und der Autarkiegrad um bis zu 73 % durch eine variable Grenzkostenoptimierung bei zusätzlicher E-Auto Berücksichtigung gesteigert werden können. Der Eigenverbrauch der PV-Erzeugung wird durch den stationären Batteriespeicher auf 71 % mehr als verdoppelt. Das beispielhafte Szenario hat einen Haushaltsverbrauch von 5 MWh pro Jahr und besteht aus einer 5 kWp PV-Anlage, mit einem 5 kWh Batteriespeicher und dem Tesla Model 3 mit einer Jahresfahrleistung von 16778 km. Das erstellte Softwareprogramm kann einfach auf weitere verschiedene Anlagenkonstellationen und mit eigenen Eingangszeitreihenprofile der Haushaltslast, der PV-Erzeugung und der E-Auto Nutzung parametriert werden. Neben der Kennzahlenberechnung des konkreten Szenarios wird der jeweilige Einfluss einer Anlagenkomponente, wie PV, Batterie und Last bei deren Variation, auf die Kennzahlen grafisch gut sichtbar dargestellt. Die Ergebnisse bestätigen bisherige Arbeiten, dass die Dimensionierung der Anlagenkomponenten nach der einfachen Faust-Formel 1:1:1 erfolgen soll: Der stationäre Batteriespeicher und die PV-Anlage sollen gleich gross sein und ihre Grösse in kWh soll der Jahreslast in MWh entsprechen. Damit wird nahezu schon ein gutes Optimum von Eigenverbrauch, Eigenverbrauchsanteil und Autarkiegrad bei minimalen Energiekosten gefunden und die Netzbelastung durch Bezug und Einspeisung kann reduziert werden. N2 - With the developed, mixed-integer-linear optimization model, a major contribution is made that the most important key figures of a PV storage system, such as the self-consumption rate raises up to 89 % and the degree of self-sufficiency by up to 73 %, are increased by variable marginal cost optimization with additional e-vehicle consumption. The stationary battery more than doubles the self-consumption rate of the PV energy generation to 71 %. The example scenario has a household load of 5 MWh per year and consists of a 5 kWp PV system, with a 5 kWh battery storage and the Tesla Model 3 e-car with an annual output of 16778 km. The program can easily be parameterized to other different system constellations and with its own input-time-series profiles of the household load, the PV generation and the use of the electric car. In addition to the calculation of the specific key figures, the respective influence of a system component, such as PV, battery and load, when varied on the key figures, is shown graphically. The results confirm previous research papers that the dimensioning of the system components should take place according to the simple formula 1: 1: 1: the stationary battery storage and the PV system should be same sized and their size in kWh should correspond to the annual load in MWh. In doing so, a good optimum of self-consumption, self-consumption share and degree of self-sufficiency with minimal energy costs is usually found and the electrical grid load through procurement and feed-in can be reduced. T2 - Analysis of optimization potential of electrical prosumer households with e-car use, stationary rechargeable battery and exogenous PV generation and load profiles KW - Autarkiegrad KW - Eigenverbrauchsoptimierung KW - Energiemodelloptimierung KW - Prosumer Haushalt KW - gemischt-ganzzahlige lineare Optimierung Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3651 ER - TY - THES A1 - Lutz, Gabriel T1 - Energiemonitoring, ISO 50001 und ein regionales Klimaneutralitätsbündnis am Beispiel eines Logistikunternehmens N2 - Die Aktualität des Klimawandels fordert Maßnahmen in privaten und wirtschaftlichen Bereichen. Die Veränderungen des Klimas führen dazu, dass Regelungen und Gesetze für das Energiewesen der Unternehmen entwickelt werden. Die Gesetze verpflichten die Unternehmen für Energie- und Umweltaudits. Viele Unternehmen führen noch zusätzliche Maßnahmen für eine Verbesserung der Energieeffizienz und des Emissionsausstoßes ein. Die Maßnahmen werden immer relevanter. Die Norm ISO 50001 unterstützt Unternehmen bei der Einführung und bei der Aufrechterhaltung eines Energiemanagementsystems. Das Energiemanagement hilft dabei, die energiebezogene Leistung zu verbessern und einen kontinuierlichen Verbesserungsprozess umzusetzen. Eine weitere freiwillige Möglichkeit ist das Klimaneutralitätsbündnis 2025. Das Bündnis soll den Mitgliedern helfen, den Emissionsausstoß zu verbessern. Die Mitglieder werden über einen definierten Zeitraum von 12 Jahren begleitet, um die Geschäftsprozesse anschließend klimaneutral zu gestalten. Diese Arbeit beschäftigt sich mit den Anforderungen der Norm ISO 50001 und dem Klimaneutralitätsbündnis. Beides sind freiwillige Instrumente, welche Unternehmen verwenden können, um das eigene Energiewesen zu optimieren und etwas zum Klimaschutz beizutragen. Die Forschung dieser Arbeit beschäftigt sich mit dem Zusammenwirken der beiden Instrumente. Es wird untersucht, ob eine parallele Einführung und Bearbeitung in den Unternehmen möglich ist. Zusätzlich werden die Inhalte und die Anforderungen gegenübergestellt. Mögliche Überschneidungen werden zu Zwecken einer Erleichterung für die Unternehmen überprüft. Im Zuge dieser Arbeit wird ein Energiemonitoring beim Logistikunternehmen Gebrüder Weiss GmbH eingeführt. Das Unternehmen mit Sitz in Lauterach (Vorarlberg) betreibt weltweit rund 165 Standorte. Die Niederlassung in Lauterach bildet den Versuchsstandort für das Energiemonitoring. Es werden geeignete Partnerunternehmen gesucht, welche ein Energiemonitoringsystem anbieten. Im Zuge der Partnersuche wird ein Pilotprojekt umgesetzt, welches dem Unternehmen erste Einblicke in die Materie bietet. Nach dem erfolgreichen Abschluss des Pilotprojektes folgt die Implementierung des Energiemonitorings. Die einzelnen Schritte und Herausforderungen des Projektes werden dargelegt und die abschließende Umsetzung wird beschrieben. Nach der Einführung in Lauterach folgt die weltweite Ausrollung des Energiemonitorings in allen Standorten. KW - Energiemonitoring KW - ISO 50001 KW - Klimaneutralitätsbündnis Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3661 ER - TY - THES A1 - Atzl, Beatrice T1 - Synthesis of doped polycrystalline silicon carbide films for light-emitting diodes N2 - Graphite substrates underwent two methods of creating doped silicon carbide films via carbothermal reduction; the first method being liquid-phase processing, or dip-coating, and the second gas-phase processing, otherwise referred to as the solid-vapour reaction. The dip-coating procedure resulted in flaky coatings, while the solid-vapour reaction resulted in polycrystalline films with columnar growth that displayed promising morphological and electrical properties. The films were tested on their performance as semiconductor diodes, and proved that carbothermal reduction in the gas phase is a promising technique for creating polycrystalline silicon carbide films for the application of light-emitting diodes. KW - Silicon carbide KW - Polycrystalline KW - Light emitting diodes KW - Carbothermal reduction Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3652 ER - TY - THES A1 - Kadinger, Miriam T1 - Eindimensionales Siliziumkarbid-Faserwachstum ohne Katalysator über karbothermische Reduktion N2 - In dieser Arbeit werden eindimensionale Siliziumkarbid-Fasern über die karbothermische Reduktion von stickstoffdotiertem Siliziumoxykarbid-Glas, welches über einen Sol-Gel-Prozess synthetisiert wurde, hergestellt. Als Wachstumssubstrat für die Fasern werden drei Arten von Kohlenstofffasern verwendet, die entweder in Sol eingelegt sind oder erst bei der karbothermischen Reduktion mit dem Precursor im Graphittiegel eingelegt werden. Es werden vier Formen von eindimensionalem Siliziumkarbid produziert, bei denen Durchmesser und Länge von <100 nm bis zu mehreren µm variieren. Die Charakterisierung der synthetisierten Fasern erfolgt über optische Mikroskopie, Rasterelektronenmikroskopie und Raman-Spektroskopie. Der Einfluss der Druckentwicklung während der karbothermischen Reduktion auf das Faserwachstum wird anhand von Druck-Temperatur-Verläufen ermittelt. KW - Eindimensionales Siliziumkarbid Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3658 ER - TY - JOUR A1 - Serečunová, Stanislava A1 - Seyringer, Dana A1 - Seyringer, Heinz A1 - Uherek, František T1 - Design and optimization of 1x2N Y-branch optical splitters for telecommunication applications JF - Journal of Electrical Engineering N2 - This paper presents the design and optimization of 1x2N Y-branch optical splitters for telecom applications. A waveguide channel profile, used in the splitter design, is based on a standard silica-on-silicon material platform. Except for the lengths of the used Y-branches, design parameters such as port pitch between the waveguides and simulation parameters for all splitters were considered fixed. For every Y-branch splitter, insertion loss, non-uniformity, and background crosstalk are calculated. According to the minimum insertion loss and minimum non-uniformity, the optimum length for each Y-branch is determined. Finally, the individual Y-branches are cascade joined to design various Y-branch optical splitters, from 1x2 to 1x64. KW - Optical splitter KW - Y-branch splitter KW - Telekommunikation KW - Splitter design Y1 - 2020 U6 - http://dx.doi.org/10.2478/jee-2020-0048 SN - 1339-309X VL - 71. Jg. IS - H. 5 SP - 353 EP - 358 ER - TY - CHAP A1 - Hainberger, Rainer A1 - Muellner, Paul A1 - Eggeling, Moritz A1 - Maese-Novo, Alejandro A1 - Nevlacsil, Stefan A1 - Schotter, Jörg A1 - Vogelbacher, Florian A1 - Kraft, Jochen A1 - Sagmeister, Martin A1 - Zhou, Xue A1 - Huang, Jinhua A1 - Li, Mingzhu A1 - Jiang, Ke-Jian A1 - Song, Yanlin A1 - Seyringer, Dana A1 - Rank, Elisabet A1 - Drexler, Wolfgang ED - García-Blanco, Sonia M. ED - Cheben, Pavel T1 - CMOS-compatible silicon nitride waveguide photonic building blocks and their application for optical coherence tomography and other sensing applications T2 - Integrated Optics: Devices, Materials, and Technologies XXIV. 3–6 February 2020. San Francisco, California, United States KW - Optical coherence tomography KW - Sensing applications KW - Waveguide photonic building blocks s KW - Arrayed waveguide gratings Y1 - 2020 SN - 9781510633308 SN - 9781510633292 U6 - http://dx.doi.org/10.1117/12.2543585 IS - 112830P PB - SPIE CY - Bellingham, Washington ER - TY - CHAP A1 - Seyringer, Dana A1 - Serecunova, Stanislava A1 - Seyringer, Heinz A1 - Uherek, František ED - Lee, B. ED - Mazzali, C. ED - Corwin, K. ED - Jason Jones, R. T1 - Impact of phased array on optical performance of AWG-spectrometers T2 - Frontiers in Optics 2020. 14–17 September 2020. Washington, DC United States N2 - We studied an impact of phased array on optical performance and size of SiN based AWG-spectrometers, which plays a significant role in integration on chip. AWG-spectrometer was designed for TM-polarization and 850 nm central wavelength. KW - AWG-spectrometer KW - OCT KW - Optical coherence tomography Y1 - 2020 UR - https://www.osapublishing.org/abstract.cfm?URI=FiO-2020-JTh4B.13 SN - 978-1-943580-80-4 IS - JTh4B.13 PB - Optical Society of America ER - TY - JOUR A1 - Kuckert-Wöstheinrich, Andrea A1 - van der Geest, Sjaak T1 - Kultur-adäquate und Person-zentrierte Pflege BT - zum Beispiel: das große Geschäft JF - Praxis Pflegen Y1 - 2020 SN - 2190-0620 VL - 11. Jg. IS - H. 41 SP - 14 EP - 17 ER - TY - JOUR A1 - Ströbl, Stephan A1 - Domke, Matthias A1 - Rühm, Adrian A1 - Sroka, Ronald T1 - Investigation of non-uniformly emitting optical fiber diffusers on the light distribution in tissue Y1 - 2020 U6 - http://dx.doi.org/10.1364/BOE.394494 VL - 11. Jg. IS - H. 7 SP - 3601 EP - 3617 ER - TY - JOUR A1 - Merz, Robert A1 - Hoch, Ralph A1 - Drexel, Damian ED - Ramsauer, Christian ED - Wolf, Matthias ED - Hulla, Maria T1 - A cloud based research and learning factory for industrial production JF - Procedia Manufacturing. Learning Factories across the value chain – from innovation to service – The 10th Conference on Learning Factories 2020 N2 - The Digital Factory Vorarlberg is the youngest Research Center of Vorarlberg University of Applied Sciences. In the lab of the research center a research and learning factory has been established for educating students and employees of industrial partners. Showcases and best practice scenarios for various topics of digitalization in the manufacturing industry are demonstrated. In addition, novel methods and technologies for digital production, cloud-based manufacturing, data analytics, IT- and OT-security or digital twins are being developed. The factory comprises only a minimum core of logistics and fabrication processes to guarantee manageability within an academic setup. As a product, fidget spinners are being fabricated. A webshop allows customers to individually design their products and directly place orders in the factory. A centralized SCADA-System is the core data hub for the factory. Various data analytic tools and methods and a novel database for IoT-applications are connected to the SCADA-System. As an alternative to on premise manufacturing, orders can be pushed into a cloud-based manufacturing platform, which has been developed at the Digital Factory. A broker system allows fabrication in distributed facilities and offers various optimization services. Concepts, such as outsourcing product configuration to customers or new types of engineering services in cloud-based manufacturing can be explored and demonstrated. In this paper, we present the basic concept of the Digital Factory Vorarlberg, as well as some of the newly developed topics. KW - Cloud-based research KW - Learning Factory KW - Digital Factory Y1 - 2020 U6 - http://dx.doi.org/10.1016/j.promfg.2020.04.097 VL - o.Jg. IS - Bd. 45 SP - 215 EP - 221 ER - TY - JOUR A1 - Dorn, Prof. Dr. Christian A1 - Wolters, Dr. Jörg-Michael T1 - Buddhistische Kampfkunst & Psychologie als Lebensweg & Heilkunst BT - Shaolin Wu Fo Dao - Eine neue Heil- & Kampfkunstform basierend auf den Traditionen und Lehren der Shaolin und des Budo . JF - Ursache & Wirkung N2 - Shaolin Wu Fo Dao – die Synthese japanischer und chinesischer Kampfkunst-Lehre auf der Grundlage zen-buddhistischer Theorie und Praxis ist eine neu geschaffene Disziplin. In dieser Fusion verbinden sich wesentliche Elemente aus Budo und Shaolin (-Wudao), deren traditionellen Körper-Geist-Übungen von Kampftechnik (Bu/Wu) und Meditation (Zen/Chan) als originäre Weg- und Heilslehre (Do/Dao) seit jeher der Persönlichkeits- und spirituellen Entwicklung des Ausübenden dienten. Hier nun, in der Überwindung alter Grenzen zwischen japanischer und chinesischer Kampfkunstsysteme („hart“ und „weich“), wurde hier nun erstmaligen ein zusammengewachsenes Kampfkunstsystem kreiert, um die beidseits positiven Wirkungen auf den Menschen zu bündeln und – und das ist das Besondere – sie in den Dienst buddhistischer (Butsu, jap.: Buddha / chin. Fo) Psychologie und Psychotherapie zu stellen. Die Verbindung von Budo mit Shaolin als eigenständiges praktisches Lehrkonzept, allein schon eine „revolutionäre Innovation“, erfährt durch ihren Einsatz als spezielle Methode einer Heilkunst zusätzlich Pioniercharakter in der Behandlung von Leid. Gemeint sind sowohl Ansätze aus der Budopädagogik und speziellen Budotherapie zur Heilung, Linderung oder Prävention von physischen, psychosomatischen und psychischen Krisen, Störungen, Krankheiten, Behinderungen und Leiden, als auch im Sinne des philosophischen und wissenschaftlichen Buddhismus, „das Leid in der Welt zu mindern“, zum Wohle des Menschen, für sein Glück und Frieden zu arbeiten. KW - Buddhistische Psychologie KW - Buddhistische Heilkunst KW - Budo KW - Shaolin KW - Buddhistische Kampfkunst Y1 - 2020 VL - 2020 ER - TY - CHAP A1 - King, Julian A1 - Mochalski, Pawel A1 - Teschl, Gerald A1 - Teschl, Susanne A1 - Mayhew, Christopher A. A1 - Ghorbani, Ramin A1 - Schmidt, Florian M. A1 - Unterkofler, Karl ED - Beauchamp, Jonathan ED - Davis, Cristina ED - Pleil, Joachim T1 - Physiological modeling of exhaled compounds T2 - Breathborne biomarkers and the human volatilome N2 - Blood flow and ventilatory flow strongly influence the concentrations of volatile organic compounds (VOCs) in exhaled breath. The physicochemical properties of a compound (e.g., water solubility) additionally determine if the concentration of the compound in breath reflects the alveolar concentration, the concentration in the upper airways, or a mixture of both. Mathematical modeling based on mass balance equations helps to understand how measured breath concentrations are related to their corresponding blood concentrations and physiological parameters, such as metabolic rates and endogenous production rates. In addition, the influence of inhaled compounds on their exhaled concentrations can be quantified and appropriate correction formulas can be derived. Isoprene and acetone, two endogenous VOCs with very different water solubility, have been modeled to explain the essential features of their behavior in breath. This chapter introduces the theory of physiological modeling of exhaled VOCs, with examples of isoprene and acetone. Y1 - 2020 SN - 978-0-12-819967-1 U6 - http://dx.doi.org/10.1016/B978-0-12-819967-1.00003-7 SP - 43 EP - 62 PB - Elsevier CY - Amsterdam ET - Second edition ER - TY - JOUR A1 - Kuckert-Wöstheinrich, Andrea A1 - Höhmann, Ulrike T1 - "Mit dem Alter ist das schrecklich, wenn man sich selbst nicht mehr richtig sauber machen kann, eine Schweinerei!" - Ein Forschungsprojekt in einer Altenpflegeeinrichtung JF - Die Praxisanleitung KW - Ausscheidung KW - Alter KW - stationäre Altenhilfe KW - Altenheim KW - Kot Y1 - 2020 SN - 2699-7568 SN - 2699-755X VL - 1. Jg. IS - H. 4 SP - 23 EP - 24 ER - TY - CHAP A1 - Meierhofer, Jürg A1 - Dobler, Martin A1 - Frick, Klaus A1 - Schweiger, Lukas ED - Bigdeli, Ali ED - Baines, Tim T1 - Smart service patterns for small manufacturing enterprises T2 - Advanced Services for Sustainability and Growth. Spring Servitization Conference 2020, 14-16 September 2020 KW - Servitization KW - Smart service KW - SME KW - Rapid service prototyping KW - Data science Y1 - 2020 SN - 978-1-85449-429-0 SP - 88 EP - 95 PB - Aston Business School CY - Birmingham ER - TY - JOUR A1 - Kuckert-Wöstheinrich, Andrea T1 - Ausscheidungen: Pflegerischer Umgang in unterschiedlichen Settings BT - Einführung JF - Die Praxisanleitung KW - Ausscheidung Y1 - 2020 SN - 2699-7568 SN - 2699-755X VL - 1. Jg. IS - H. 4 SP - 19 EP - 20 ER - TY - JOUR A1 - Kuckert-Wöstheinrich, Andrea T1 - Pflegerische Interventionen unter die Lupe genommen JF - Die Praxisanleitung KW - Pflege KW - Ausscheidung KW - Interventionen KW - Maßnahmen Y1 - 2020 SN - 2699-7568 SN - 2699-755X VL - 1. Jg. IS - H. 4 SP - 30 EP - 33 ER - TY - JOUR A1 - Kuckert-Wöstheinrich, Andrea T1 - Kulturelle Sozialisationspozesse - das Toilettenpapier JF - Die Praxisanleitung KW - Kultur KW - Ausscheidung KW - Sozialisation Y1 - 2020 SN - 2699-7568 SN - 2699-755X VL - 1. Jg. IS - H. 4 SP - 20 EP - 22 ER - TY - BOOK A1 - Dobler, Martin A1 - Etschmann, Roman A1 - Kugler, Petra A1 - Meierhofer, Jürg A1 - Olbert-Bock, Sibylle A1 - Redzepi, Abdullah A1 - Schumacher, Jens A1 - Thiel, Christian A1 - Tietz, Rigo T1 - Data Science für KMU leicht gemacht BT - Data4KMU. Aktuelle Erkenntnisse und Lösungen N2 - Daten werden heute oft auch als das «neue Gold» bezeichnet. Denn die letzten Jahre haben gezeigt, dass Daten die Grundlage erstaunlicher unter- nehmerischer Erfolgsgeschichten sein können. Dabei ist die Arbeit mit Daten nicht grundlegend neu. Vielmehr geht es heute im Vergleich zu früher um nahezu unendlich grossen Mengen an Daten, die im Rahmen nahezu aller denkbaren Prozesse oder Schnittstellen gesammelt, gespeichert und ausgewertet werden können. Unter anderem beinhaltet dies Maschinendaten, unternehmens- interne Prozesse oder Daten über Kunden und den Markt, welche die Grundlage für lernende Systeme (Künstliche Intelligenz) bilden. Wir können heute davon ausgehen, dass künftig nicht mehr die technische Machbarkeit, sondern die mensch- liche Vorstellungskraft die Grenzen des Möglichen definiert. Bekannt sind vor allem etliche Erfolgsgeschichten von Grossunternehmen, die ihr Geschäft auf Daten aufbauen. Etablierte KMU sind hingegen noch zögerlicher, mit Daten zu arbeiten und diese wertschöpfend einzusetzen. Diese Broschüre geht auf die besondere Situation von KMU im Umgang mit Daten und Data Science ein. Denn auch für KMU kann es lohnend oder sogar zwingend notwendig sein, sich mit dem Thema «Data Science» zu beschäftigen. Daten und Data Science bieten grosse Chancen, sie können aber auch zu einer Bedrohung im Wettbewerb werden. Und, zu lange warten sollten KMU nicht, die Zeit drängt. Denn Geschwindigkeit ist einer der zentralen Wettbewerbsfaktoren im digitalen Zeitalter. Das IBH-Lab KMUdigital unter- stützt KMU dabei, den herausfordernden Weg in eine digitale Zukunft schneller und einfacher zu gehen. Diese Broschüre geht daher insbesondere auf die Rolle von Daten und Data Science für KMU in der Bodenseeregion ein. Sie stellt eine Zusammen- fassung ausgewählter Erkenntnisse und Handlungs- empfehlungen dar, die wir in einem zweijährigen Forschungsprojekt gemeinsam mit 16 Unternehmen aus der Bodenseeregion gewinnen konnten. Die Erkenntnisse sollen KMU bei der Nutzung von Daten anhand von Data Science unterstützen. Dabei ist es kein Ziel, dass KMU zu einem «kleinen Google» werden. Vielmehr braucht es KMU- spezifische Lösungen und Überlegungen, wie mit Daten sinnvoll, zielorientiert und ressourcen- schonend umgegangen werden kann. Wie kann das aussehen? Welche Chancen, Herausforderungen und Lösungen bieten sich KMU vor dem Hinter- grund ihrer besonderen Situation? Was muss dazu im Unternehmen verändert werden? Welche Unterschiede bestehen im Vergleich zu Gross- unternehmen auf diesem Weg? Diese und weitere Fragen stehen im Mittelpunkt des vorliegenden Projektberichts zum Einzelprojekt «Data Science für KMU leicht gemacht» oder kurz «Data Science 4 KMU» bzw. «Data4KMU», welches unter dem Dach des IBH-Labs KMUdigital in den Jahren 2018 bis 2019 durchgeführt wurde. Dazu werden Daten und Data Science aus mehreren Perspektiven betrachtet, die nicht unabhängig voneinander sind: Strategie und Geschäftsmodell, Services und Prozesse, Leadership, HRM und Organisation, Organisationskultur und Ganzheitichkeit, sowie Technologie. Diese Perspektiven greifen wir in den nachfolgenden Kapiteln auf. Die vorliegende Broschüre wäre ohne die wertvolle Unterstützung der Praxispartner des Projektes, des Managements des IBH-Labs KMUdigital sowie ohne die finanzielle Projektförderung durch die Inter- nationale Bodenseehochschule (IBH) und Interreg nicht möglich gewesen. Ihnen allen gilt unser ganz besonderer Dank! Y1 - 2020 PB - Internationale Bodenseehochschule Labs CY - Kreuzlingen ER - TY - CHAP A1 - Dobler, Martin A1 - Kalkhofer, Hanno A1 - Schumacher, Jens ED - Guenduez, Ali ED - Schedler, Kuno T1 - Innovationspotenzial smarter Technologien. Arbeitspaket 3 BT - Jahresbericht 2019. Smart Government Akademie Bodensee Y1 - 2020 SP - 53 EP - 62 PB - Smart Government Lab IMP-HSG Universität St.Gallen CY - St. Gallen ER - TY - JOUR A1 - Arzbacher, Stefan A1 - Rahmatian, Nima A1 - Ostermann, Alexander A1 - Gasser, Tobias M. A1 - Loerting, Thomas A1 - Petrasch, Jörg T1 - Co-Deposition of Gas Hydrates by Pressurized Thermal Evaporation JF - Physical Chemistry Chemical Physics N2 - Gas hydrates are usually synthesized by bringing together a pressurized gas and liquid or solid water. In both cases, the transport of gas or water to the hydrate growth site is hindered once an initial film of hydrate has grown at the water–gas interface. A seemingly forgotten gas-phase technique overcomes this problem by slowly depositing water vapor on a cold surface in the presence of the pressurized guest gas. Despite being used for the synthesis of low-formation-pressure hydrates, it has not yet been tested for hydrates of CO 2 and CH 4 . Moreover, the potential of the technique for the study of hydrate decomposition has not been recognized yet. We employ two advanced implementations of the condensation technique to form hydrates of CO 2 and CH 4 and demonstrate the applicability of the process for the study of hydrate decomposition and the phenomenon of self-preservation. Our results show that CO 2 and CH 4 hydrate samples deposited on graphite at 261–265 K are almost pure hydrates with an ice fraction of less than 8%. Rapid depressurization experiments with thin deposits (approx. 330 mm thickness) of CO 2 hydrate on an aluminum surface at 265 K yield identical dissociation curves when the deposition is done at identical pressure. However, hydrates deposited at 1 MPa almost completely withstand decomposition after rapid depressurization to 0.1 MPa, while samples deposited at 2 MPa decompose 7 times faster. Therefore, this synthesis technique is not only applicable for the study of hydrate decomposition but can also be used for the controlled deposition of a super-preserved hydrate. Y1 - 2020 U6 - http://dx.doi.org/10.1039/C9CP04735B VL - 22 IS - 7 SP - 4266 EP - 4275 ER - TY - JOUR A1 - Aguiló-Aguayo, Noemí A1 - Hubmann, Dominic A1 - Khan, Fahad Ullah A1 - Arzbacher, Stefan A1 - Bechtold, Thomas T1 - Water-based slurries for high-energy LiFePO4 batteries using embroidered current collectors JF - Scientific Reports N2 - Greater specific energy densities in lithium-ion batteries can be achieved by using three-dimensional (3D) porous current collectors, which allow for greater areal mass loadings of the electroactive material. In this paper, we present the use of embroidered current collectors for the preparation of thick, pouch-type Li-ion batteries. Experiments were performed on LiFePO 4 (LFP) water-based slurries using styrene-butadiene rubber (SBR) as binder and sodium carboxymethyl cellulose (CMC) as thickener, and formulations of different rheological characteristics were investigated. The electrochemical performance (cyclic voltammetry, rate capability) and morphological characteristics of the LFP half-pouch cells (X-ray micro computed tomography and scanning electron microscopy) were compared between the formulations. An optimum electrode formulation was identified, and a mechanism is proposed to explain differences between the formulations. With the optimum electrode formulation, 350 µm casted electrodes with high mechanical stability were achieved. Electrodes exhibited 4–6 times greater areal mass loadings (4–6 mAh cm −2 ) and 50% greater electroactive material weight than with foils. In tests of half- and full-pouch embroidered cells, a 50% capacity utilization at 1C-rate and 11% at 2C-rate were observed, with a full recovery at C/5-rate. The cycling stability was also maintained over 55 cycles. Y1 - 2020 U6 - http://dx.doi.org/10.1038/s41598-020-62553-3 VL - 10 ER - TY - JOUR A1 - Eder, Elias A1 - Preißinger, Markus T1 - Experimental analysis of the humidification of air in bubble columns for thermal water treatment systems JF - Experimental Thermal and Fluid Science N2 - The humidification-dehumidification process (HDH) for desalination is a promising technology to address water scarcity issues in rural regions. However, a low humidifier efficiency is a weakness of the process. Bubble column humidifiers (BCH) are promising for HDH, as they provide enhanced heat and mass transfer and have low maintenance requirements. Previous studies of HDH-systems with BCHs draw different conclusions regarding the impact of superficial air velocity and liquid height on the humidification. Furthermore, the impact of flow characteristics has never been investigated systematically at all. In this study, an optimized BCH test setup that allows for optical analysis of the humidifier is used and evaluated. Our test setup is validated, since the influence of water temperature on the humidification, which is exponential, is reproduced. Measurements with seawater show that the normalised system productivity is increased by about 56 % with an increase in superficial air velocity from 0.5 to 5 cm/s. Furthermore, the system productivity is increased by around 29 % with an increase in liquid height from 60 to 378 mm. While the impact of superficial air velocity can be traced back to temperature changes at the humidifier and dehumidifier outlets, the impact of liquid height is shown to be caused by a smaller heat loss surface in the humidifier with an increase in liquid height. For the impact of sieve plate orifice diameter, a clear influence on the humidification is not apparent, this parameter needs to be investigated further. Finally, our new test setup allows for analysing the humidification of air (1) in a systematic way, (2) in relevant measurement ranges and (3) in comparison with optical analyses of the flow characteristics. KW - Bubble column humidifier KW - Air humidification KW - Humidification-dehumidification KW - Desalination KW - Water treatment Y1 - 2020 U6 - http://dx.doi.org/10.1016/j.expthermflusci.2020.110063 VL - o.Jg. IS - 115 ER - TY - BOOK A1 - Wolters, Jörg-Michael A1 - Dorn, Christian T1 - BUDO BT - Wesen und Wirken der Kampfkunst. Budopädagogik & Budotherapie N2 - Budo als Oberbegriff für die traditionellen Kampfkünste, eigentlich namentlich Japans, aber hier im weiteren Sinne alle Kampf- und Bewegungskünste Asiens, die sich als Weg und nicht Sport begreifen, ist in den letzten Jahren vermehrt Gegenstand der öffentlichen Diskussion. Jüngere Veröffentlichungen zum Thema nehmen das historisch, philosophisch, psychologisch und pädagogisch Besondere und sich vom modernen Kampfsport gänzlich Unterscheidende in den Blick, ohne dass allerdings weiterhin begrifflich und inhaltlich falsche Vorstellungen durch die absurde Vereinnahmung der allein dem Budo zugeschrieben Wesenszüge und Wirkweisen in sog. "Budo-Sport"-Verbänden immer mehr verbreiten. Gerade so, als könne man dem modernen Kampfsport durch den Zusatz "Budo" (der suggerieren soll, man beziehe sich auf dessen Wesentliche, "Geistige") etwa einen ehrwürdig-traditionellen Charakter verleihen und den Wettkampfsport bereichern, gar ethisch aufwerten. Insofern bedarf es immer noch oder immer mehr der Aufklärung darüber, was denn das eigentliche Wesen und Wirken von Budo überhaupt ausmacht, um dem Ganzen gerecht zu werden. Dabei soll sich dieses Buch nun weniger auf die historische, seit der Edo-Periode (1600-1868) vor allem vom Zen-Buddhismus (neben Konfuzianismus und Taoismus sowie Shaolin) geprägte Entwicklung von Budo aus den alten Kriegskünsten (Bugei und Bujutsu) eingehen, als auf das nunmehr auch heute noch Wesentliche und "Spezielle". Budo als spirituelle wie praktisch-philosophische Weg-Lehre und dadurch Kampf-"Kunst" kann, recht verstanden, ein einzigartiger Schatz in der Theorie und Praxis des Studiums von "Kampf" und "Kämpfen-Können" sowie des Selbst sein, und am Ende auch des eigenen Lebens. Budo wirkt! Es ist ein auf Bewegung, Begegnung und Besinnung angelegtes bewährtes ganzheitliches Instrument der Selbsterziehung, Charakterschulung und Persönlichkeitsentwicklung und als originärer Weg ("Do") zum "Friedvollen Krieger" eine konkrete Anleitung zu körperlicher, seelischer, geistiger, d.h. psycho-physischer wie psycho-emotionaler Selbstbeherrschung, die auf der Grundlage von stetig geübter Achtsamkeit und Wertschätzung in der Meisterschaft zu Einsicht und Gewaltverzicht führt. In diesem Buch wird das Thema Budo, sein Wesen und Wirken, aus Erfahrung und wissenschaftlicher Erkenntnis heraus analysiert, um ein ebenso weitergehendes wie tieferes Verständnis von der Sache zu fördern. Die Autoren (Vorstellung im entsprechenden Kapitel hinten), allesamt! KW - Budopädagogik KW - Budotherapie KW - Kampfkunst KW - Shaolin Y1 - 2020 SN - 978-3-7519-2340-8 PB - BoD - Books on Demand CY - Norderstedt ER - TY - JOUR A1 - Johannes, Susanne A1 - Kuckert-Wöstheinrich, Andrea T1 - Angehörigenarbeit. Der Spagat zwischen dem Wohl des zu Versorgenden und der „dritten Person“ JF - Die Praxisanleitung Y1 - 2020 VL - 1. Jg. IS - H. 2 SP - 14 EP - 20 ER - TY - JOUR A1 - Kuckert-Wöstheinrich, Andrea A1 - Johannes, Susanne T1 - Versorgung von Menschen mit Demenz in unterschiedlichen Settings JF - Die Praxisanleitung Y1 - 2020 VL - 1. Jg. IS - H. 1 SP - 14 EP - 21 ER - TY - JOUR A1 - Bonerz, Stefan A1 - Flick, Theresa A1 - Kalb, Simone A1 - Sayfutdinov, Ismael T1 - Quasilineare Tauchankerspule BT - Neues Sensorkonzept als Alternative für LVDT-Sensoren JF - Elektronik Y1 - 2020 VL - 66. Jg. IS - H. 12 ER - TY - THES A1 - Kuckert-Wöstheinrich, Andrea T1 - Ältere LGBTQI* Männer, viel mehr als schwul und trans BT - Aufforderung an die Pflege: Anerkennend und person-zentriert autonomes Gesundheitsmanagement unterstützen N2 - Seit einigen Jahren beschäftigen sich immer mehr Autor*innen mit der Frage, welche Handreichungen Mitarbeitende im Gesundheitssystem brauchen, um adäquater auf die Bedürfnisse älterer LGBTQI* Personen einzugehen, deren (pflegerische) Anliegen nicht erkannt werden, von schwer zu überwindenden Barrieren im Gesundheitssystem berichten und die sich diskriminiert fühlen. Der Fokus der Publikationen liegt auf der sexuellen Orientierung und / oder der Genderidentität, einem Teilaspekt der Identität einer Person. Je nach Kontext und Personen sind andere Teilidentitäten, wie z.B. Familienstatus, Alter, Ethnizität, Teilhabe an sozialen Gruppen unterschiedlich stark berücksichtigt. In einer qualitativen Studie wurden, unter Integration der autoethnographischen Methode, acht Männer zwischen 53 und 75 Jahren aus den Niederlanden und Deutschland in autobiografischen-narrativen Interviews befragt, inwiefern die Coronapandemie ihre Vorstellungen vom gesunden Altern verändert hat. Alle Männer hatten komplexe Biografien, gekennzeichnet von Partnerverlust, Arbeitslosigkeit, Altersfragen, familiären und gesundheitlichen Herausforderungen neben anderen identitätsstiftenden Faktoren. Aber alle identifizierten sich seit ihrer Jugend mit ihrer sexuellen oder Genderidentität, hatten aus vielen Krisen gelernt und sorgten mit einem für sich klaren Management, dass sie auch im Alter gesund bleiben würden – Autonomie stand hoch im Kurs! Die Person nicht nur auf die Zugehörigkeit zur LGBTQI* Gruppe zu reduzieren, sondern in ihrer gesamten Identität in den Gesundheitseinrichtungen zu berücksichtigen kennzeichnet eine adäquate Pflege. Y1 - 2020 U6 - http://dx.doi.org/10.25924/opus-3837 ER - TY - JOUR A1 - Schmiedinger, Thomas A1 - Partel, Stefan A1 - Lechleitner, Thomas A1 - Eiter, Oliver A1 - Hekl, Daniel A1 - Kaseman, Stephan A1 - Lukas, Peter A1 - Edlinger, Johannes A1 - Lechner, Judith A1 - Seppi, Thomas T1 - Interdigitated aluminium and titanium sensors for assessing epithelial barrier functionality by electric cell-substrate impedance spectroscopy (ECIS) JF - Biomedical Microdevices N2 - Electric cell-substrate impedance spectroscopy (ECIS) enables non-invasive and continuous read-out of electrical parameters of living tissue. The aim of the current study was to investigate the performance of interdigitated sensors with 50 μm electrode width and 50 μm inter-electrode distance made of gold, aluminium, and titanium for monitoring the barrier properties of epithelial cells in tissue culture. At first, the measurement performance of the photolithographic fabricated sensors was characterized by defined reference electrolytes. The sensors were used to monitor the electrical properties of two adherent epithelial barrier tissue models: renal proximal tubular LLC-PK1 cells, representing a normal functional transporting epithelium, and human cervical cancer-derived HeLa cells, forming non-transporting cancerous epithelial tissue. Then, the impedance spectra obtained were analysed by numerically fitting the parameters of the two different models to the measured impedance spectrum. Aluminium sensors proved to be as sensitive and consistent in repeated online-recordings for continuous cell growth and differentiation monitoring assensors made of gold, the standard electrode material. Titanium electrodes exhibited an elevated intrinsic ohmic resistance incomparison to gold reflecting its lower electric conductivity. Analysis of impedance spectra through applying models and numerical data fitting enabled the detailed investigation of the development and properties of a functional transporting epithelial tissue using either gold or aluminium sensors. The result of the data obtained, supports the consideration of aluminium and titanium sensor materials as potential alternatives to gold sensors for advanced application of ECIS spectroscopy. Y1 - 2020 U6 - http://dx.doi.org/10.1007/s10544-020-00486-4 SN - 1387-2176 SN - 1572-8781 VL - 22. Jg. IS - H. 2/30 ER - TY - JOUR A1 - Wieland, Felicia A1 - Bruch, Richard A1 - Bergmann, Michael A1 - Partel, Stefan A1 - Urban, Gerald A. A1 - Dincer, Can T1 - Enhanced protein immobilization on polymers - a plasma surface activation study JF - Polymers N2 - Over the last years, polymers have gained great attention as substrate material, because of the possibility to produce low-cost sensors in a high-throughput manner or for rapid prototyping and the wide variety of polymeric materials available with different features (like transparency, flexibility, stretchability, etc.). For almost all biosensing applications, the interaction between biomolecules (for example, antibodies, proteins or enzymes) and the employed substrate surface is highly important. In order to realize an effective biomolecule immobilization on polymers, different surface activation techniques, including chemical and physical methods, exist. Among them, plasma treatment offers an easy, fast and effective activation of the surfaces by micro/nanotexturing and generating functional groups (including carboxylic acids, amines, esters, aldehydes or hydroxyl groups). Hence, here we present a systematic and comprehensive plasma activation study of various polymeric surfaces by optimizing different parameters, including power, time, substrate temperature and gas composition. Thereby, the highest immobilization efficiency along with a homogenous biomolecule distribution is achieved with a 5-min plasma treatment under a gas composition of 50% oxygen and nitrogen, at a power of 1000 W and a substrate temperature of 80 C. These results are also confirmed by different surface characterization methods, including SEM, XPS and contact angle measurements. Y1 - 2020 U6 - http://dx.doi.org/10.3390/polym12010104 SN - 2073-4360 VL - 12. Jg. IS - H. 1/104 ER - TY - JOUR A1 - Lopez-Villegas, Antonio A1 - Lopez-Liria, Reme A1 - Rocamora-Perez, Patricia A1 - Pezzella, Alfonso A1 - Dudau, Viktor A1 - Kouta, Christiana A1 - Nielson, Dorthe A1 - Baiocco, Roberto A1 - Kuckert-Wöstheinrich, Andrea A1 - Papadopoulos, Rena T1 - Achieving real equality in health and social care: IENE9 project, a work in progress for LGBT+ people JF - European Journal of Public Health N2 - Issues with professional conduct and discrimination against Lesbian, Gay, Bisexual, Transgender (LGBT+) people in health and social care, continue to exist in most EU countries and worldwide. The project IENE9 titled: “Developing a culturally competent and compassionate LGBT+ curriculum in health and social care education” aims to enable teacher/trainers of theory and practice to enhance their skills regarding LGBT+ issues and develop teaching tools to support the inclusion of LGBT+ issues within health and social care curricula. The newly culturally competent and compassionate LGBT+ curriculum will be delivered though a Massive Open Online Course (MOOC) which is aimed at health and social care workers, professionals and learners across Europe and worldwide. We have identified educational policies and guidelines at institutions teaching in health and social care, taken into account for developing the learning/teaching resources. The MOOC will be an innovative training model based on the Papadopoulos (2014) model for “Culturally Competent Compassion”. The module provides a logical and easy to follow structure based on its four constructs 'Culturally Aware and Compassionate Learning', 'Culturally Knowledgeable and Compassionate Learning', 'Culturally Sensitive and Compassionate Learning', 'Culturally Competent and Compassionate Learning'. Specific training may result in better knowledge and skills of the health and social care workforce, which helps to reduce inequalities and communication with LGBT+ people, as well as diminishing the feelings of stigma or discrimination experienced. KW - Bisexuality KW - Homosexuality KW - Social stigma KW - Knowledge acquisition KW - Cultural competence Y1 - 2020 U6 - http://dx.doi.org/https://doi.org/10.1093/eurpub/ckaa166.746 SN - 1101-1262 SN - 1464-360X VL - 30. Jg. IS - Supplement 5/ckaa166.746 ER - TY - RPRT A1 - Papadopoulos, Irena A1 - Dudau, Victor A1 - Duru, Anne-Maria A1 - Kouta, Christiana A1 - Rousou, Elena A1 - Nicolaidou, Elena A1 - Rocamora Perez, Patricia A1 - Lopez, Remedio A1 - Baiocco, Roberto A1 - Pistella, Jessica A1 - Kuckert-Wöstheinrich, Andrea A1 - Ziegler, Sabine ED - Nielson, Dorthe S. ED - Twisttmann Bay, Laila ED - Johansen, Anders Valentin ED - Pezzella, Alfonso T1 - Developing a culturally competent and compassionate LGBT+ curriculum in health and social care education : IENE 9 BT - internet mapping and systematic documentation of educational policies and guidelines, as well as legislation at European and national level for LGBTQ+ inclusive education N2 - This is Intellectual Output 2 (IO2) of the project “Developing a culturally competent and compassionate LGBT+ curriculum in health and social care education“ IENE9. The aim of the project is to enable teacher/trainers of theory and practice to enhance their skills regarding LGBT+ issues and develop teaching tools to support the inclusion of LGBT+ issues within health and social care curricula. The newly culturally competent and compassionate LGBT+ curriculum will be delivered through a MOOC which is aimed at health and social care teachers/trainers, workers, professionals, and learners across Europe and worldwide. The IO2 of this project, Internet Mapping and Systematic documentation of educational policies and guidelines as well as legislation at European and national level for LGBT+ inclusive education, aims to create an easy to navigate resource with information about European and national legislation/guidance/policies. Visit www.iene-lgbt.com for more information. Y1 - 2020 U6 - http://dx.doi.org/10.13140/RG.2.2.14537.57446 ER - TY - CHAP A1 - Ilg, Markus A1 - Baumeister, Alexander ED - Keimer, Imke ED - Egle, Ulrich T1 - Business-Analytics im Marketing-Controlling BT - eine Anwendungsfallstudie für den Automobilmarkt T2 - Die Digitalisierung der Controlling-Funktion. Anwendungsbeispiele aus Theorie und Praxis N2 - Die Digitalisierung verändert Geschäftsmodelle und betriebliche Prozesse. Zugleich beeinflussen auch eine verbesserte Datenverfügbarkeit und leistungsfähige analytische Methoden das Controlling und erfordern vermehrt das Einbringen statistischer und informationstechnologischer Fertigkeiten und Kenntnisse. An einem Fallbeispiel aus dem Marketing-Controlling zeigt der Beitrag den Einsatz von Methoden der Business Analytics und thematisiert die Aufgaben des Controllings im digitalen Zeitalter. KW - Digitalisierung KW - Controlling KW - Data analytics KW - Marketing analytics Y1 - 2020 SN - 978-3-658-29195-2 SN - 978-3-658-29196-9 U6 - http://dx.doi.org/10.1007/978-3-658-29196-9_9 N1 - Verlagshinweis zum Abstract: Die NutzerInnen dürfen die Inhalte nur zum Zwecke der wissenschaftlichen Forschung ansehen, drucken, kopieren, herunterladen sowie für Text- und Datamining verwerten. Die Inhalte dürfen weder ganz noch teilweise wörtlich (wieder)veröffentlicht oder für kommerzielle Zwecke verwendet werden. Die NutzerInnen müssen sicherstellen, dass die Urheberpersönlichkeitsrechte des/der AutorIn sowie gegebenenfalls bestehende Rechte Dritter an den Inhalten oder Teilen der Inhalte nicht verletzt werden. SP - 141 EP - 158 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Matylitskaya, Volha A1 - Kasemann, Stephan A1 - Kostal, Elisabeth A1 - Partel, Stefan T1 - An electrochemical study with three redox substances on a carbon based nanogap electrode array T2 - ECS Meeting Abstracts Y1 - 2020 U6 - http://dx.doi.org/10.1149/MA2020-01271864mtgabs SN - 2151-2043 VL - MA2020 IS - H. 1/1864: IMCS 02: Chemical and Biosensors, Medical/Health, and Wearables ER - TY - JOUR A1 - Simma-Wallinger, Angelika T1 - Zeigen, nicht erklären! JF - ORF Public Value Texte N2 - Medien sind während der Covid-Pandemie in besonderem Maße gefordert, komplexe Sachverhalte, wie Inzidenzen und exponentielles Wachstum einfach zu erklären. Informationsgrafiken sind dazu bestens geeignet, erfordern allerdings hohe Kompetenz in der Erstellung. Dieser Artikel plädiert für die Einführung eines eigenen journalistischen Genres, nämlich des visuellen Journalismus. KW - Covid KW - Infografik KW - Visueller Journalismus Y1 - 2020 UR - https://zukunft.orf.at/show_content.php?sid=147&pvi_id=2289&pvi_medientyp=t&oti_tag=TEXTE%20Corona VL - o. Jg. IS - H. 24: Medienqualität in Zeiten von Corona SP - 20 EP - 23 ER - TY - JOUR A1 - Voyer, Joel A1 - Zehetner, Johann A1 - Klien, Stefan A1 - Ausserer, Florian A1 - Velkavrh, Igor T1 - Production and tribological characterization of tailored laser-induced surface 3D microtextures JF - Lubricants. Special Issue "Laser-Induced Periodic Surface Nano- and Microstructures for Tribological Applications" KW - laser microtexturing KW - ultra-short pulsed laser KW - surface characterization KW - tribological characterization KW - friction KW - wear Y1 - 2019 U6 - http://dx.doi.org/10.3390/lubricants7080067 SN - 2075-4442 VL - 7. Jg. IS - H. 8/67 ER - TY - JOUR A1 - Kepplinger, Peter A1 - Fäßler, Bernhard A1 - Huber, Gerhard A1 - Muhandiram Arachchige, Subhoda Tharangi Ireshika A1 - Rheinberger, Klaus A1 - Preißinger, Markus T1 - Autonomes Demand Side Management verteilter Energiespeicher JF - e&i Elektrotechnik und Informationstechnik N2 - Verbraucherseitige Laststeuerung (Demand Side Management – DSM) wird als ein möglicher Ansatz betrachtet, um die Auswirkungen des Ausbaus von fluktuierenden Erneuerbaren im Stromnetz auszugleichen. Sollen viele verteilte Energiesysteme damit angesprochen werden, stellen zentralistische Ansätze dabei hohe Anforderungen an die Kommunikationsinfrastruktur. Als Alternative wird vielfach eine autonome Laststeuerung (ADSM) mit anreizbasierter Optimierung direkt auf dem Verbrauchergerät betrachtet. Dabei kann die Anreizfunktion mittels unidirektionaler Kommunikation übertragen werden. Am Forschungszentrum Energie der Fachhochschule Vorarlberg wurden in den letzten Jahren Algorithmen und Prototypen für den Einsatz von ADSM auf verschiedensten verteilten Energiespeichern im elektrischen Stromnetz entwickelt. Dabei werden sowohl thermische Energiespeicher (z. B. Haushalts-Warmwasserspeicher) als auch elektrochemische Speicher (z. B. Batteriespeichersysteme oder Elektroautos) betrachtet. Außerdem werden die Auswirkungen solcher Systeme auf das elektrische Verteilnetz untersucht. Dieser Artikel gibt einen Überblick über die entwickelten Methoden und Ergebnisse aus diesem Forschungsfeld mit dem Ziel, ein weitreichendes Verständnis für die Chancen und Grenzen des ADSM zu schaffen. KW - Demand Side Management KW - Lastmanagement KW - Warmwasserspeicher KW - Stationäre Batteriespeicher KW - Elektromobilität Y1 - 2019 U6 - http://dx.doi.org/10.1007/s00502-019-00782-9 SN - 1613-7620 VL - 2019 ER - TY - JOUR A1 - Zach, Christina A1 - Unterkofler, Karl A1 - Fraunberger, Peter A1 - Drexel, Heinz A1 - Muendlein, Axel T1 - Unrecognized high occurrence of genetically confirmed hereditary carnitine palmitoyltransferase II deficiency in an Austrian family points to the ongoing underdiagnosis of the disease JF - Frontiers in Genetics N2 - Adult muscle carnitine palmitoyltransferase (CPT) II deficiency is a rare autosomal recessive disorder of long-chain fatty acid metabolism. It is typically associated with recurrent episodes of exercise-induced rhabdomyolysis and myoglobinuria, in most cases caused by a c.338C > T mutation in the CPT2 gene. Here we present the pedigree of one of the largest family studies of CPT II deficiency caused by the c.338C > T mutation, documented so far. The pedigree comprises 24 blood relatives of the index patient, a 32 year old female with genetically proven CPT II deficiency. In total, the mutation was detected in 20 family members, among them five homozygotes and 15 heterozygotes. Among all homozygotes, first symptoms of CPT II deficiency occurred during childhood. Additionally, two already deceased relatives of the index patient were carriers of at least one copy of the genetic variant, revealing a remarkably high prevalence of the c.338C > T mutation within the tested family. Beside the index patient, only one individual had been diagnosed with CPT II deficiency prior to this study and three cases of CPT II deficiency were newly detected by this family study, pointing to a general underdiagnosis of the disease. Therefore, this study emphasizes the need to raise awareness of CPT II deficiency for correct diagnosis and accurate management of the disease. Y1 - 2019 U6 - http://dx.doi.org/10.3389/fgene.2019.00497 VL - o.Jg. IS - Bd. 10:497 ER - TY - CHAP A1 - Sagmeister, Martin A1 - Jessenig, Stefan A1 - Muellner, Paul A1 - Nevlacsil, Stefan A1 - Maese-Novo, Alejandro A1 - Eggeling, Moritz A1 - Hainberger, Rainer A1 - Seyringer, Dana A1 - Drexler, Wolfgang A1 - Rank, Elisabet A1 - Kraft, Jochen ED - Kayahan, Ersin ED - Oral, Ahmet Yavuz ED - Aköz, Mehmet Emre ED - Aksan, Onur Alp ED - Cinar, Ibrahim T1 - Development of a monolithically integrated, CMOS-compatible SiN photonics process flow for sensor and medical applications T2 - Interphotonics 2019. Book of abstracts. 2nd International Conference on Photonics Research. November 4-9 2019. Antalya, Turkey N2 - Abstract: ams AG is a leading provider of sensing solutions developing semiconductor sensors in a wide variety of fields, with optical sensing as one of the key competences. Since integrated photonics is a promising technology for new sensor systems, ams AG has been developing processes for fully integrated CMOS-compatible photonic components based on Si3N4. This talk will provide an overview on the processing of basic photonic building blocks and their optical properties and performance. We will also give examples for applications in the fields of optical coherence tomography and opto-chemical gas sensing. In the 1980s photonics started its way for common use in telecommunication technology, using optical fiber technologies. In recent years, also a variety of photonic sensors has been proposed and developed. One of the major drawbacks of most of these photonic devices has been the lack of integration into existing (semiconductor) production processes, so far. This integration is feasible using SiN material systems to process monolithically integrated CMOS-compatible photonic sensors in the visible and near-infrared spectrum. We will present the basic processing steps for the SiN photonic technology, the development of some critical processing steps such as SiN deposition and SiN etching as well as several photonic components (waveguides, splitters, etc.) with their optical properties. One of the applications presented relates to optical coherence tomography (OCT), a fast growing imaging technique in ophthalmology. Drawbacks of existing OCT systems are their high costs as well as their bulkiness, which prevents a wider spread use of OCT systems. One way to overcome both cost and size issues is to integrate optical and electrical components on a single chip. Part of this work was carried out in the framework of the projects COHESION (funded by the Austrian Research Promotion Agency (FFG), no. 848588), OCTCHIP (funded by the EU’ Horizon 2020 research and innovation programme, no. 688173), and COLODOR (M-ERA.NET transnational Call 2015, funded by the Austrian Research Promotion Agency (FFG), no.854066, and the Bundesministerium für Bildung und Forschung, Germany). KW - SiN Photonics KW - Sensor KW - CMOS-Compatible KW - OCT KW - Industry Y1 - 2019 ER - TY - CHAP A1 - Rank, Elisabet A. A1 - Nevlacsil, Stefan A1 - Müllner, Paul A1 - Hainberger, Rainer A1 - Maese-Novo, Alejandro A1 - Dülk, Marcus A1 - Gloor, Stefan A1 - Völker, Matthias A1 - Verwaal, Nanko A1 - Meinhardt, Gerald A1 - Sagmeister, Martin A1 - Kraft, Jochen A1 - Morrissey, Padraic A1 - Jezzini, Moises A1 - Quan, Zhiheng A1 - O'Brien, Peter A1 - Richter, Stefan A1 - Kempe, Michael A1 - Seyringer, Dana A1 - Drexler, Wolfgang ED - Wojtkowski, Maciej ED - Boppart, Stephen A. ED - Oh, Wang-Yuhl T1 - Spectral domain and swept source optical coherence tomography on a photonic integrated circuit at 840nm for ophthalmic application T2 - Optical Coherence Imaging Techniques and Imaging in Scattering Media III. Event: European Conferences on Biomedical Optics, 2019, Munich, Germany Y1 - 2019 SN - 978-1-5106-2849-6 U6 - http://dx.doi.org/10.1117/12.2526903 PB - SPIE CY - Bellingham, Washington ER - TY - CHAP A1 - Ströbl, Stephan A1 - Domke, Matthias A1 - Trebst, Tilmann A1 - Sroka, Ronald ED - Lilge, Lothar D. ED - Philipp, Carsten M. T1 - Radiation profile measurement methods for optical light diffusers: comparison of imaging and non-imaging methods T2 - Medical Laser Applications and Laser-Tissue Interactions IX. 23–24 June 2019. Munich, Germany Y1 - 2019 SN - 978-1-5106-2851-9 U6 - http://dx.doi.org/10.1117/12.2526571 PB - SPIE CY - Bellingham, Washington ER - TY - CHAP A1 - Trommelschläger, Karin A1 - Künz, Andreas A1 - Ritter, Walter ED - Piazolo, Felix ED - Kempter, Guido ED - Promberger, Kurt T1 - Developing user centered technological prototypes to maintain physical health T2 - Innovative solutions for an ageing society. Proceedings of SMARTER LIVES meets uDay 19. 28.05.2019, Bolzano - Bozen KW - motivation stategy KW - physical activity KW - technology prototypes KW - elderly KW - human centered design Y1 - 2019 SP - 81 EP - 92 PB - Pabst Science Publishers CY - Lengerich ER - TY - JOUR A1 - Pallauf, Martin A1 - Hämmerle, Isabella A1 - Kofler, Manfred A1 - Förster, Kristina A1 - Werner, Tobias A1 - Kathrein, Judith T1 - Assistenztechnologien im Wohnraum älterer Menschen - Erwartungen und Akzeptanz JF - Umweltpsychologie KW - bebaute Umwelt KW - Altern KW - Altern in häuslicher Umgebung KW - Betreutes Wohnen KW - Informationstechnologie Y1 - 2019 SN - 1414-3304 VL - 23. Jg. IS - H. 1 SP - 10 EP - 33 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Eder, Elias A1 - Preißinger, Markus T1 - Analyse der Befeuchtung von Luft in einer Blasensäule T2 - 13. Forschungsforum der österreichischen Fachhochschulen. FH Forschungsforum 2019. Forschung bewegt. 24. & 25. April am Campus 1 Wiender Neustadt Y1 - 2019 PB - FH Wiener Neustadt GmbH CY - Wiener Neustadt ER - TY - CHAP A1 - Chovan, Jozef A1 - Tomaska, Martin A1 - Uherek, Frantisek A1 - Hasko, Daniel A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Koza, Eduard A1 - Pavlov, Jozef T1 - Concept of PIC packaging with microwave, DC and fiber array ports T2 - 2019 International Workshop on Fiber Optics in Access Networks (FOAN) N2 - Progress in integrated photonics enables development of integrated photonics circuits with new unique properties, circuits of the future, and overcomes current limits in information and communication technologies. The packaging of photonic integrated circuits is necessary for taking them out of research laboratories into real implementation in the information and communication technology applications. Telecom optical fibers are still being the best transmission medium of digital data and analogue signals for long distance applications. The effective coupling of optical radiation between telecom optical fiber with ten microns core dimension and photonic integrated circuits optical waveguides with submicron dimensions are necessary. To address these challenges, we present our concept of photonics integrated circuit packaging with radio frequency, direct current and fiber array ports with automated active alignment system. KW - integrated photonics KW - photonics integrated circuits KW - packaging KW - information and communication technology KW - concept Y1 - 2019 SN - 978-1-7281-1563-4 SP - 38 EP - 41 PB - IEEE ER - TY - CHAP A1 - Stroebl, Stephan A1 - Domke, Matthias A1 - Trebst, Tilmann A1 - Sroka, Ronald ED - Gannot, Israel T1 - Comparison of imaging and non-imaging based methods to determine the radiation profile of fiber diffusers for photodynamic therapy T2 - Optical Fibers and Sensors for Medical Diagnostics and Treatment Applications XIX. 2–3 February 2019. San Francisco, California, United States Y1 - 2019 U6 - http://dx.doi.org/10.1117/12.2508384 PB - SPIE CY - Bellingham, Washington ER - TY - CHAP A1 - Hellwig, Michael A1 - Beyer, Hans-Georg A1 - Spettel, Patrick T1 - Evolutionsstrategien zur Optimierung unter Nebenbedingungen. 100 - Forschung im Rahmen von Exzellenzprogrammen T2 - 13. Forschungsforum der Österreichischen Fachhochschulen. Forschung bewegt. 24. & 25. April am Campus 1 Wiener Neustadt. FH Forschungsforum 2019 Y1 - 2019 PB - Fachhochschule Wiener Neustadt GmbH CY - Wiener Neustadt ER - TY - CHAP A1 - Werner, Tobias A1 - Trommelschläger, Karin A1 - Hohpe, Sarah ED - Friedrich, Petra ED - Fuchs, Dominik T1 - Studie zur kombinierten Wirkung von Licht, Geruch und (Ultra-)Schall T2 - Assistive Technik für selbstbestimmtes Wohnen. 6. Ambient Medicine® Forum. 19.-20. Februar 2019 KW - AAL KW - Licht KW - Geruch KW - Schall KW - Ultraschall Y1 - 2019 SN - 978-3-7369-9961-9 SP - 9 EP - 14 PB - Cuvillier Verlag CY - Göttingen ER - TY - CHAP A1 - Böhler, Doris T1 - Doing refugee categorisation? Reflections on asylum procedures involving narratives taken from asylum court decisions T2 - Social Protection & Human Dignity. IFSW European Conference. Vienna 2019. Abstracts. Workshops and Paper Presentations Y1 - 2019 UR - https://www.ifsw2019.com/wp/wp-content/uploads/2019/09/ABSTRACTS-book-final.pdf SP - 25 ER - TY - CHAP A1 - Duden, Antje A1 - Mayer, Horst Otto A1 - Meusburger, Magdalena A1 - McCormick Williams, Michael A1 - Wilms, Falko ED - Duden, Antje T1 - Was ist zu tun? T2 - Reflexive Kommunikation analog und digital Y1 - 2019 SP - 71 EP - 76 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - JFULL ED - Clapper, Timothy C. ED - Harviainen, J. Tuomas ED - Kriz, Willy Christian T1 - Simulation & Gaming. An Interdisciplinary Journal of Theory, Practice and Research Y1 - 2019 SN - 1046-8781 VL - 50 PB - Sage Publishers ER - TY - JOUR A1 - Piredda, Giovanni A1 - Stroj, Sandra A1 - Ziss, Dorian A1 - Stangl, Julian A1 - Trotta, Rinaldo A1 - Martin-Sanchez, Javier A1 - Rastelli, Armando T1 - Micro-machining of PMN-PT crystals with ultrashort laser pulses JF - Applied Physics A N2 - Lead–magnesium niobate lead titanate (PMN-PT) has been proven as an excellent material for sensing and actuating applications. The fabrication of advanced ultra-small PMN-PT-based devices relies on the availability of sophisticated procedures for the micro-machining of PMN-PT thin films or bulk substrates. Approaches reported up to date include chemical etching, excimer laser ablation, and ion milling. To ensure an excellent device performance, a key mandatory feature for a micro-machining process is to preserve as far as possible the crystalline quality of the substrates; in other words, the fabrication method must induce a low density of cracks and other kind of defects. In this work, we demonstrate a relatively fast procedure for the fabrication of high-quality PMN-PT micro-machined actuators employing green femtosecond laser pulses. The fabricated devices feature the absence of extended cracks and well-defined edges with relatively low roughness, which is advantageous for the further integration of nanomaterials onto the piezoelectric actuators. Y1 - 2019 U6 - http://dx.doi.org/10.1007/s00339-019-2460-9 VL - 125. Jg. IS - H. 3/201 ER - TY - CHAP A1 - Trommelschläger, Karin A1 - Kempter, Guido ED - Conti, Massimo ED - Lebedev, Georgy ED - Martinez Madrid, Natividad ED - Orcioni, Simone ED - Seepold, Ralf T1 - Technologies in the bedroom that improve the quality of sleep T2 - EMBC WorkshopTelemedicine and Telemonitoring in AAL Home Environments. 41st Engineering in Medicine and Biology (EMB) ConferenceJuly 23, 2019Berlin, Germany N2 - During two studies the influence of technologies on sleep were analyzed. The first one is about the effect of light on the circadian rhythm and as a consequence on sleep quality of persons in a vegetative state. The second one, which is still running, surveys the influence of several technologies on the sleep of elderly people living in a nursing home. Y1 - 2019 SP - 21 EP - 23 PB - Reutlingen University CY - Reutlingen ER - TY - JOUR A1 - Spettel, Patrick A1 - Beyer, Hans-Georg T1 - Analysis of the (μ/μI,λ)-σ-self-adaptation evolution strategy with repair by projection applied to a conically constrained problem JF - IEEE Transactions on Evolutionary Computation KW - Evolution strategies KW - repair by projection KW - conically constrained problem KW - intermediate recombination Y1 - 2019 U6 - http://dx.doi.org/10.1109/TEVC.2019.2930316 SN - 1089-778X N1 - Early Access 2019 ER - TY - CHAP A1 - Werner, Tobias A1 - Trommelschläger, Karin A1 - Jost, Patrick ED - Piazolo, Felix ED - Kempter, Guido ED - Promberger, Kurt T1 - Creating activating and relaxing atmospheres using light, scent and sound T2 - Innovative solutions for an ageing society. Proceedings of SMARTER LIVES meets uDay 19. 28.05.2019, Bolzano - Bozen KW - AAL KW - Light KW - Scent KW - Sound KW - Ultrasound Y1 - 2019 SN - 978-3-95853-511-4 SP - 148 EP - 157 PB - Pabst Science Publishers CY - Lengerich ER - TY - JOUR A1 - Spettel, Patrick A1 - Beyer, Hans-Georg T1 - Analysis of the (μ/μI,λ)-CSA-ES with repair by projection applied to a conically constrained problem JF - Evolutionary Computation KW - Evolution strategy KW - constraint handling KW - repair by projection KW - cumulative step size adaptation KW - conically constrained problem Y1 - 2019 U6 - http://dx.doi.org/10.1162/evco_a_00261 SN - 1063-6560 N1 - Early Access 2019 VL - 2019 ER - TY - JOUR A1 - Arzbacher, Stefan A1 - Rahmatian, Nima A1 - Ostermann, Alexander A1 - Massani, Bernhard A1 - Loerting, Thomas A1 - Petrasch, Jörg T1 - Macroscopic defects upon decomposition of CO2 clathrate hydrate crystals JF - Physical Chemistry Chemical Physics KW - Clathrate Hydrates Y1 - 2019 U6 - http://dx.doi.org/10.1039/C8CP07871H VL - 21. Jg. IS - H. 19 SP - 9694 EP - 9708 ER - TY - JOUR A1 - Spettel, Patrick A1 - Beyer, Hans-Georg T1 - A multi-recombinative active matrix adaptation evolution strategy for constrained optimization JF - Soft Computing KW - Constrained optimization KW - Active matrix adaptation evolution strategy KW - Black-box optimization benchmarking Y1 - 2019 U6 - http://dx.doi.org/10.1007/s00500-018-03736-z VL - 23 IS - 16 SP - 6847 EP - 6869 ER - TY - CHAP A1 - Duden, Antje A1 - McCormick Williams, Michael ED - Duden, Antje T1 - Wie meistern wir die einzelnen Phasen?! T2 - Reflexive Kommunikation analog und digital KW - Teilnehmenden-Kreis KW - Zeitrahmen KW - Einverständnis KW - Verantwortung Y1 - 2019 SN - 978-3-86573-822-6 SP - 33 EP - 39 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Duden, Antje ED - Duden, Antje T1 - Reflexive Kommunikation in Lernenden Organisationen T2 - Reflexive Kommunikation analog und digital KW - Reflexive Kommunikationsprozesse KW - Leadership KW - Management KW - Wirklichkeiten KW - Lernende Organisationen Y1 - 2019 SN - 978-3-86573-822-6 SP - 3 EP - 20 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - JOUR A1 - Amann, Peter A1 - Degerman, David A1 - Lee, Ming-Tao A1 - Alexander, John D. A1 - Shipilin, Mikhail A1 - Wang, Hsin-Yi A1 - Cavalca, Filippo A1 - Weston, Matthew A1 - Gladh, Jörgen A1 - Blom, Mikael A1 - Björkhage, Mikael A1 - Löfgren, Patrik A1 - Schlueter, Christoph A1 - Loemker, Patrick A1 - Ederer, Katrin A1 - Drube, Wolfgang A1 - Noei, Heshmat A1 - Zehetner, Johann A1 - Wentzel, Henrik A1 - Ahlund, John A1 - Nilsson, Anders T1 - A high-pressure x-ray photoelectron spectroscopy instrument for studies of industrially relevant catalytic reactions at pressures of several bars JF - Review of Scientific Instruments Y1 - 2019 U6 - http://dx.doi.org/10.1063/1.5109321 VL - 90. Jg. IS - H. 10/103102 ER - TY - CHAP A1 - Kikkawa, Toshiko A1 - Kriz, Willy C. A1 - Junkichi, Sugiura ED - Hamada, Ryoju ED - Soranastaporn, Songsri ED - Kanegae, Hidehiko ED - Dumrongrojwatthana, Pongchai ED - Chaisanit, Settachai ED - Rizzi, Paola ED - Dumblekar, Vinod T1 - The effects of debriefing on the performance and attitude of Austrian university students and cultural differences to Japanese students T2 - Neo-simulation and gaming toward active learning Y1 - 2019 SN - 978-981-13-8038-9 U6 - http://dx.doi.org/10.1007/978-981-13-8039-6_48 SP - 515 EP - 524 PB - Springer CY - Singapore ER - TY - CHAP A1 - Malin, Sebastian A1 - Plankensteiner, Kathrin A1 - Merz, Robert A1 - Mayr, Reinhard A1 - Schöndorfer, Sebastian A1 - Thomas, Mike ED - Haber, Peter ED - Lampoltshammer, Thomas ED - Mayr, Manfred T1 - Smart recommendation system to simplify projecting for an HMI/SCADA platform T2 - Data Science – Analytics and Applications. Proceedings of the 2nd International Data Science Conference – iDSC2019 Y1 - 2019 SN - 978-3-658-27494-8 U6 - http://dx.doi.org/10.1007/978-3-658-27495-5_13 SP - 93 EP - 95 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Domke, Matthias A1 - Stroj, Sandra A1 - Matylitsky, Victor ED - Makimura, Tetsuya ED - Raciukaitis, Gediminas ED - Molpeceres, Carlos T1 - Laser material processing in the ablation-cooled regime: Ablation efficiency and quality using single fs-, bursts of fs-, and single ns-pulses T2 - Laser Applications in Microelectronic and Optoelectronic Manufacturing (LAMOM) XXIV. 4–6 February 2019. San Francisco, California, United States Y1 - 2019 U6 - http://dx.doi.org/10.1117/12.2514441 PB - SPIE CY - Bellingham, Washington ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Gašo, Peter A1 - Pudiš, Dušan ED - Sitek, Jozef ED - Vajda, Jan ED - Jamnicky, Igor T1 - Design of polymer based 8-channel, 100-GHz AWG applying various photonics tools T2 - Applied Physics of Condensed Matter (APCOM 2019). Strbsko Pleso, Slovak Republic. 19-21 June 2019 Y1 - 2019 SN - 978-0-7354-1873-8 U6 - http://dx.doi.org/10.1063/1.5119493 IS - 2131/020040 PB - AIP Publishing CY - Melville, NY ER - TY - JOUR A1 - Kriz, Willy C. A1 - Clapper, Timothy C. A1 - Harviainen, J. Tuomas T1 - Obituary for Allan G. Feldt: Pioneer in Urban Gaming and Co-Founder of the International Simulation and Gaming Association (ISAGA) JF - Simulation & Gaming Y1 - 2019 U6 - http://dx.doi.org/10.1177/1046878119863248 VL - 50. Jg. IS - H. 3 SP - 408 EP - 410 ER - TY - CHAP A1 - Meusburger, Magdalena A1 - Wilms, Falko ED - Duden, Antje T1 - Praktische Herausforderungen der reflexiven Kommunikation T2 - Reflexive Kommunikation analog und digital KW - Reflexive Kommunikation KW - Beziehungsgestaltung KW - Prozesssteuerung KW - Themenbearbeitung Y1 - 2019 SN - 978-3-86573-822-6 SP - 21 EP - 31 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Weber, Heidi A1 - Gancho, Sara A1 - Mateus, Americo A1 - Cruz Rodrigues, Antonio ED - Duarte, Emilia T1 - Varying mindsets in Design Thinking. Why they change during the process and how to nudge them T2 - Doctoral Design Conference'19. TransFormation. Proceedings Book of DDC'19. IADE | Universidade Europeia. Portugal | Lisbon | 22 - 24.05.2019 KW - Creativity KW - Design Thinking KW - Mindsets KW - Influence KW - Psychology Y1 - 2019 UR - http://ddc2019.unidcom-iade.pt/ SN - 978-989-8473-27-1 U6 - http://dx.doi.org/10.25924/opus-3125 SP - 45 EP - 52 PB - Edicoes IADE CY - Lisbon ER - TY - CHAP A1 - Seyringer, Dana A1 - Burtscher, Catalina A1 - Gajdosova, Lenka ED - Kayahan, Ersin ED - Oral, Ahmet Yavuz ED - Aköz, Mehmet Emre ED - Aksan, Onur Alp ED - Cinar, Ibrahim T1 - Optical splitters: design and applications T2 - Interphotonics 2019. Book of abstracts. 2nd International Conference on Photonics Research. November 4-9 2019. Antalya, Turkey N2 - Optical splitters are passive optical components, which have found applications in a wide range of telecom, sensing, medical and many other scientific areas. Low-index contrast optical splitters (Silica-on-Silicon (SoS) based waveguide devices) feature many advantages such as low fiber coupling losses and low propagation losses. They are considered an attractive DWDM solution in the telecommunication for all optical signal processing in optical communication systems. Nowadays the steadily increasing data volume in communication networks is driven by a rapid proliferation of home-based and business computers, storage capacities, processing capabilities and the extensive availability of Internet. The challenge is to transfer high data volumes in short periods of time over high distances as lossless as possible. The task of the optical splitters in Fiber-to-the-x (FTTx) network is to split one optical signal in many identical signals bringing for example the same TV signal in different households. Of course, the more buildings can be served by one optical splitter the lower are the installation costs. High-index contrast optical splitters (such as silicon, silicon nitride or polymer based waveguide devices) feature much smaller waveguide size compared to low index contrast splitters. Such compact devices can easily be implemented on-chip and have already been used in the development of optical sensors, devices for DNA diagnostics and for infrared spectroscopy. We will present the latest achievements in the design of two mostly used optical splitters (MMI and Y-branch) and discuss their advantages and disadvantages. Finally, some applications of the splitters developed in the frame of various projects will be presented. This work was carried out in the framework of the project PHOCOP (no. SK-AT-2017-0013) and NAMOPRISIN (no. SK-AT-2017-0005) from the Slovak research and development agency of the Ministry of Education, Science, Research and Sport of the Slovak Republic and SK 16/2018 and 15/2018 from OeAD-GmbH. KW - optical splitters KW - optical datatransmissison KW - Y-branch splitter KW - MMI splitter KW - photonics Y1 - 2019 ER - TY - CHAP A1 - Hellwig, Michael A1 - Spettel, Patrick A1 - Beyer, Hans-Georg ED - Lopez-Ibanez, Manuel, T1 - Comparison of contemporary evolutionary algorithms on the rotated Klee-Minty problem T2 - GECCO '19. Proceedings of the 2019 Genetic and Evolutionary Computation Conference. July 13 - 17, 2019. Prague, Czech Republic KW - Constrained Optimization KW - Evolutionary Algorithms KW - Constraint Handling KW - Benchmarking KW - Rotated Klee-Minty Problem Y1 - 2019 SN - 978-1-4503-6748-6 U6 - http://dx.doi.org/10.1145/3319619.3326805 SP - 1879 EP - 1887 PB - ACM CY - New York, NY ER - TY - CHAP A1 - Kikkawa, Toshiko A1 - Kriz, Willy Christian A1 - Sugiura, Junkichi ED - Wardaszko, Marcin T1 - Differences between facilitator-guided and self-guided debriefing on the attitudes of university students BT - Past and future. Heritage and progress. ISAGA 50th Anniversary Conference Proceedings 2019 T2 - Simulation & Gaming through times and across disciplines Y1 - 2019 SN - 978-83-66502-01-7 SP - 617 EP - 628 PB - Kozminsky University CY - Warsaw ER - TY - CHAP A1 - Hellwig, Michael A1 - Beyer, Hans-Georg ED - Lopez-Ibanez, Manuel, T1 - Analysis of a meta-ES on a conically constrained problem T2 - GECCO '19. Proceedings of the 2019 Genetic and Evolutionary Computation Conference. July 13 - 17, 2019. Prague, Czech Republic KW - Constrained Optimization KW - Evolution Strategies KW - Theoretical Analysis Y1 - 2019 SN - 978-1-4503-6111-8 U6 - http://dx.doi.org/10.1145/3321707.3321824 SP - 673 EP - 681 PB - ACM CY - New York, NY ER - TY - JOUR A1 - Weiß, Andreas P. A1 - Popp, Tobias A1 - Zinn, Gerd A1 - Preißinger, Markus A1 - Brüggemann, Dieter T1 - A micro-turbine-generator-construction-kit (MTG-c-kit) for small-scale waste heat recovery ORC-Plants JF - Energy Y1 - 2019 U6 - http://dx.doi.org/10.1016/j.energy.2019.05.135 IS - Band 181 SP - 51 EP - 55 ER - TY - CHAP A1 - Eder, Elias A1 - Preißinger, Markus T1 - Experimental Analysis of Parameters Influencing the Humidification of Air in Bubble Columns for Thermal Water Treatment Systems T2 - HEFAT 2019. Proceedings. 14th International Conference on Heat Transfer, Fluid Mechanics and Theromdynamics. Wicklow, Ireland. 22 - 24 July 2019 Y1 - 2019 SN - 978-1-77592-191-2 SP - 566 EP - 571 ER - TY - GEN A1 - Hefel, Johanna T1 - Rezension zu: Martin W. Schnell, Christian Schulz-Quach, Christine Dunger (Hrsg.): 30 Gedanken zum Tod. Die Methode der Framework Analysis T2 - socialnet Rezensionen KW - Frame Work Analysis KW - Soziale Arbeit KW - Forschung KW - Verlust KW - Tod Y1 - 2019 UR - https://www.socialnet.de/rezensionen/24438.php ER - TY - JOUR A1 - Domke, Matthias A1 - Sonderegger, Georg A1 - Kostal, Elisabeth A1 - Matylitski, Victor A1 - Stroj, Sandra T1 - Transparent laser-structured glasses with superhydrophilic properties for anti-fogging applications JF - Applied Physics A N2 - Ultrashort pulse laser structuring enables direct modification of glass surfaces to generate superhydrophilic properties for anti-fogging applications. This approach makes coatings dispensable and the generated surfaces remain thermally, mechanically, and chemically resistant. However, the laser-generated structures usually cause scattering, which decreases transmission and may disturb the vision through the modified glass in the dry state. The aim of this study was to find a laser-processing strategy to achieve superhydrophilic, anti-fogging properties on glass surfaces with maximum transmission and minimal visual perception of the generated structure. For this purpose, we used an ultrashort-pulsed laser to generate periodic patterns of rippled circles or rough holes with varying pitch. The water contact angle and transmission of the structured glasses were measured as a function of the structured area. It was found that a periodic pattern of holes, which covers less than 1% of the surface, is already sufficient to reach the superhydrophilic state (contact angle < 5°) and provides nearly the same transmission as pristine glass. Pictures of objects imaged through dry, structured glasses, which were placed close to the lens or object, showed in both cases only a minimal decrease of contrast. If this minor drawback can be accepted, this direct laser structuring approach could be an interesting alternative to coating-based techniques and leaves even room to apply additional coatings for the fabrication of multi-functional special glasses. Y1 - 2019 U6 - http://dx.doi.org/10.1007/s00339-019-2953-6 N1 - First Online: 04 September 2019 ER - TY - JOUR A1 - Seyringer, Dana A1 - Sagmeister, Martin A1 - Maese-Novo, Alejandro A1 - Eggeling, Moritz A1 - Rank, Elisabet A. A1 - Muellner, Paul A1 - Hainberger, Rainer A1 - Drexler, Wolfgang A1 - Vlaskovic, Marko A1 - Zimmermann, Horst A1 - Meinhardt, Gerald A1 - Kraft, Jochen T1 - Technological verification of size-optimized 160-channel silicon nitride-based AWG-spectrometer for medical applications JF - Applied Physics B N2 - We present the technological verification of a size-optimized 160-channel, 50-GHz silicon nitride-based AWG-spectrometer. The spectrometer was designed for TM-polarized light with a central wavelength of 850 nm applying our proprietary “AWG-Parameters” tool. For the simulations of AWG layout, the WDM PHASAR photonics tool from Optiwave was used. The simulated results show satisfying optical properties of the designed AWG-spectrometer. However, the high-channel count causes a large AWG size with standard design approaches. To solve this problem we designed a special taper enabling the reduction of AWG structure by about 15% while keeping the same optical properties. The AWG design was fabricated and the measured spectra not only confirm the proposed size-reduction but also the improvement of optical properties of the size-optimized AWG. Y1 - 2019 U6 - http://dx.doi.org/10.1007/s00340-019-7192-1 VL - 125. Jg. IS - H. 6/88 ER - TY - JOUR A1 - Domke, Matthias A1 - Matylitsky, Victor A1 - Stroj, Sandra T1 - Surface ablation efficiency and quality of fs lasers in single-pulse mode, fs lasers in burst mode, and ns lasers JF - Applied Surface Science KW - Laser ablation KW - Ablation efficiency KW - Burst mode KW - Silicon KW - Copper KW - Steel Y1 - 2019 U6 - http://dx.doi.org/10.1016/j.apsusc.2019.144594 N1 - In Press, Corrected Proof, Available online 5 November 2019 ER - TY - CHAP A1 - Hefel, Johanna T1 - The challenges and joys of reflexive writing T2 - Social Protection & Human Dignity. IFSW European Conference. Vienna 2019. Abstracts. Workshops and Paper Presentations KW - social work KW - autoethnography KW - reflective writing Y1 - 2019 UR - https://www.ifsw2019.com/wp/wp-content/uploads/2019/09/ABSTRACTS-book-final.pdf SP - 109 ER - TY - CHAP A1 - Böhler, Doris A1 - Randall, Matthew ED - Pfaller-Rott, Monika ED - Kallay, Andrej ED - Böhler, Doris T1 - Social work with refugees in Austria BT - Statistics, trends and current challenges T2 - Social work with migrants and refugees Y1 - 2019 SN - 978-80-7599-077-8 SP - 17 EP - 30 PB - University of Ostrava CY - Ostrava ER - TY - CHAP A1 - Böhler, Doris ED - Granosik, Mariusz ED - Gulczynska, Anita ED - Kostrzynska, Malgorzata T1 - Learning together BT - Social work students and service users reflect critically on their diverse life experiences T2 - Participatory social work. Research, practice, education Y1 - 2019 SN - 978-83-233-4599-2 SP - 277 EP - 286 PB - Jagiellonian University Press CY - Krakow ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Contributions of Japanese gaming and JASAG JF - Simulation & Gaming Y1 - 2019 U6 - http://dx.doi.org/10.1177/1046878119883733 VL - 50. Jg. IS - H. 5 SP - 487 EP - 490 ER - TY - CHAP A1 - Ströbl, Stephan A1 - Wäger, Felix A1 - Domke, Matthias A1 - Sroka, Ronald T1 - Investigations on mechanical stability of laser machined optical fibre tips for medical application T2 - V Summer School “Photonics meets Biology”. 16-20 September 2019. Venue: FORTH, Heraklion, Crete, Greece. Student Abstracts N2 - Light delivery is a challenging task, when it comes to medical applications. The light is guided through optical fibers from the light source towards the treatment region. In case of interstitial light application, the light has to be decoupled from the fibre and spread to the surrounding tissue. To reach larger tissue volumes, this can be either obtained by adding a scattering volume to the tip of the fibre, or by directly modifying the optical fibre itself in order to break the total reflection within the fibre core. Such modifications can be either on the fibre surface itself or internally in the fibre core. One approach to obtain the fibre structuring could be laser induced surface roughening using an ultrafast laser source. While using volume scattering as diffusor at the fibre tip is currently the gold standard for non-thermal applications (< 0.3W/cm), the decoupling of high power laser intensities for thermal treatment options is still challenging. Structuring the fibre core itself usually is related with a loss of mechanical stability. As fibre breakage and potential loss within the human body can have serious consequences, the mechanical stability is one of the quality criterion in diffuser manufacturing. Therefore, investigations about the mechanical stability of laser manufactured optical fibre diffusers are needed. In order to evaluate the mechanical stability, a 4-point as well as a 2-point breaking test were developed. Different fibre diffusers, based on volume or surface scattering, were manufactured using fs-laser ablation techniques and its breaking strengths were investigated. It could be shown that for surface fibre modifications, the mechanical stability reduces with increasing defect depth. The stability significantly drops when the laser ablation was performed in the thermal energy range. Volume scattering modified fibres only showed a slight reduction in stability compared to un-machined fibres. In conclusion, internal fibre modification seems to be the most promising method to establish optical fibre diffusers, which are capable of several watts of emission power, while preserving its mechanical strength. Y1 - 2019 UR - http://esperia.iesl.forth.gr/~mfarsari/abstract-book.pdf SP - 13 ER - TY - CHAP A1 - Ströbl, Stephan A1 - Freymüller, Christian A1 - Domke, Matthias A1 - Sroka, Ronald T1 - Light distribution of optical fiber diffusers in turbid medium derived from air-based measurement methods T2 - VII International Symposium Topical Problems of Biophotonics 2019. Proceedings. 27-21 July, 2019. Nizhniy Novgorod - Uglich - Nizhniy Novgorod N2 - Interstitial photodynamic therapy (iPDT) treats malignant brain cancer cells by irradiation with low power laser light. The light is guided into the human body by diffuse emitting fibers. This study targets the light distribution of optical diffusers within the brain tissue. It was shown, that by submerging an optical diffuser into human brain phantom, its radiation profile measured in air converges towards a Gaussian distribution with increasing phantom depth. A camera method using digital averaging filters as well as an integrating sphere setup, both, smoothing the diffuser radiation profile were applied onto the evaluated diffuser. Y1 - 2019 SP - 269 EP - 270 ER - TY - CHAP A1 - Zumtobel, Melanie A1 - Plankensteiner, Kathrin ED - Haber, Peter ED - Lampoltshammer, Thomas ED - Mayr, Manfred T1 - Using supervised learning to predict the reliability of a welding process T2 - Data Science – Analytics and Applications. Proceedings of the 2nd International Data Science Conference – iDSC2019 Y1 - 2019 SN - ISBN 978-3-658-27494-8 U6 - http://dx.doi.org/10.1007/978-3-658-27495-5_15 SP - 99 EP - 102 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Kepplinger, Peter A1 - Preißinger, Markus ED - Gratzer, Alexander T1 - Smart Boiler = Efficient Boiler BT - Demand Side Management mit Warmwasserspeichern T2 - Effizienz und Big Data in der Energiewirtschaft. Umwelttagung des Vereins für Ökologie und Umweltforschung vom 4. bis 5. Oktober 2018 im Illwerke Zentrum Montafon (IZM) in Vandans/Montafon Y1 - 2019 SN - ISBN: 978-3-7089-1886-0 SP - 27 EP - 32 PB - Facultas CY - Wien ER - TY - CHAP A1 - Wilms, Falko ED - Duden, Antje T1 - Strukturierung von reflexiver Kommunikation in der Theorie sozialer Systeme T2 - Reflexive Kommunikation analog und digital KW - Beobachtung KW - Einheit der Differenz KW - Kalkül KW - reflexive Kommunikation Y1 - 2019 SN - 978-3-86573-822-6 SP - 41 EP - 70 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - BOOK A1 - Hefel, Johanna T1 - Verlust, Sterben und Tod über die Lebensspanne BT - Kernthemen Sozialer Arbeit am Beispiel österreichischer Fachhochschulen KW - Soziale Arbeit, Verlust, Tod, Lebensspanne, Studium, Praxis Y1 - 2019 SN - 978-3-86388-805-3 PB - Budrich UniPress Ltd. CY - Opladen ER - TY - BOOK ED - Pfaller-Rott, Monika ED - Kallay, Andrej ED - Böhler, Doris T1 - Social work with migrants and refugees Y1 - 2019 SN - 978-80-7599-077-8 PB - University of Ostrava CY - Ostrava ER - TY - BOOK ED - Duden, Antje T1 - Reflexive Kommunikation analog und digital KW - Reflexive Kommunikationsprozesse Y1 - 2019 SN - 978-3-86573-822-6 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - JOUR ED - Böhler, Doris ED - Mills, Karen T1 - Czech and Slovak social work BT - ERIS journal - Summer 2019. Connecting theory and practice Y1 - 2019 VL - 19. Jg. IS - H. 4 ER - TY - CHAP A1 - Rheinberger, Klaus A1 - Rosskopf, Ramona A1 - Preißinger, Markus A1 - Kepplinger, Peter ED - Unterkofler, Karl ED - Fetz, Thomas T1 - Analyzing autonomous demand side algorithms with parallel computation frameworks T2 - ÖMG Conference 2019. Program and book of abstracts. University of Applied Sciences Vorarlberg, Dornbirn. September 16–20, 2019 N2 - In contrast to fossil energy sources, the supply by renewable energy sources likewind and photovoltaics can not be controlled. Therefore, flexibilities on the demandside of the electric power grid, like electro-chemical energy storage systems, are usedincreasingly to match electric supply and demand at all times. To control those flex-ibilities, we consider two algorithms that both lead to linear programming problems.These are solved autonomously on the demand side, i.e., by household computers.In the classic approach, an energy price signal is sent by the electric utility to thehouseholds, which, in turn, optimize the cost of consumption within their constraints.Instead of an energy price signal, we claim that an appropriate power signal that istracked in L1-norm as close as possible by the household has favorable character-istics. We argue that an interior point of the household’s feasibility region is neveran optimal price-based point but can result in a L1-norm optimal point. Thus, pricesignals can not parametrize the complete feasibility region which may not lead to anoptimal allocation of consumption.We compare the price and power tracking algorithms over a year on the base ofone-day optimizations regarding different information settings and using a large dataset of daily household load profiles. The computational task constitutes an embarrassingly parallel problem. To this end, the performance of the two parallel computation frameworks DEF [1] and Ray [2] are investigated. The Ray framework is used to run the Python applications locally on several cores. With the DEF frameworkwe execute our Python routines parallelly in a cloud. All in all, the results providean understanding of when which computation framework and autonomous algorithmwill outperform the other. Y1 - 2019 SP - 72 PB - ÖMG CY - Wien ER - TY - CHAP A1 - Agterbos, Marieke A1 - Aldershoff, Frank A1 - Cawley, Oisin A1 - Jung, Norbert A1 - Kehoe, Joseph A1 - Klok, Eric A1 - Künz, Andreas A1 - Nilsen, Jan Harald A1 - Jost, Patrick A1 - Rothe, Irene A1 - Sandstrak, Grethe A1 - Skar, Reidun A1 - Weidmann, Karl-Heinz ED - Ashmawy, Alaa K. ED - Schreiter, Sebastian T1 - Developing health technology innovators: a collaborative learning approach T2 - Proceedings of 2019 IEEE Global Engineering Education Conference (EDUCON) Y1 - 2019 SN - 978-1-5386-9506-7 U6 - http://dx.doi.org/10.1109/EDUCON.2019.8725104 SP - 211 EP - 216 PB - Institute of Electrical and Electronics Engineers (IEEE.), Inc. CY - Danvers, MA ER - TY - CHAP A1 - Maurer, Florian A1 - Schumacher, Jens ED - Pawar, Kulwant S. ED - Potter, Andrew ED - Rogers, Helen ED - Glock, Christoph T1 - Evolving towards a smart factory of the future within supply chains: selected cases out of the Alpine space T2 - Supply Chain Networks vs Platforms: Innovations, Challenges and Opportunities. Proceedings of the 24th International Symposium on Logistics (ISL 2019). Würzburg, Germany. 14th - 17th July 2019 Y1 - 2019 UR - http://www.isl21.org/wp-content/uploads/2019/07/Full-paper-20_07_2019-Final.pdf SN - 978-0-85358-329-5 SP - 197 EP - 205 PB - Nottingham University Business School CY - Nottingham, UK ER - TY - CHAP A1 - Hefel, Johanna T1 - Social justice and diversity in relation to loss and death: a neglected issue T2 - ECSWR 2019. 10-12 April. Leuven, Belgium. Book of Abstracts KW - Social Work KW - Social Justice KW - Diversity KW - Loss KW - Death KW - Disregard Y1 - 2019 UR - https://kuleuvencongres.be/ecswr2019/files/ecswr-2019-voorblad-abstract-book-final.pdf SN - 978-9-07104-714-5 SP - 243 PB - KU Leuven CY - Leuven ER - TY - JOUR A1 - Hirt, Julian A1 - Neyer, Stefanie A1 - Nordhausen, Thomas T1 - Umfassende Literaturrecherchen - ein Kurzüberblick JF - GMS Medizin - Bibliothek - Information N2 - Zusammenfassung: Eine umfassende Literaturrecherche (Comprehensive Literature Search, CLS) bezeichnet eine umfangreiche und aufwändige Recherche mit dem Ziel, möglichst alle Studien zur Beantwortung einer zugrundeliegenden Forschungsfrage im Rahmen einer systematischen Übersichtsarbeit zu identifizieren. Konkrete Empfehlungen oder eine Definition des Begriffs CLS gibt es jedoch nicht. Der vorliegende Beitrag führt in eine Rahmung der CLS ein, stellt die damit einhergehenden Herausforderungen dar und weist auf methodische Implikationen sowie mögliche zukünftige Forschungsbereiche hin. T2 - Comprehensive literature searches – an overview KW - Literaturrecherche KW - Methoden Y1 - 2019 U6 - http://dx.doi.org/10.3205/mbi000430 VL - Volume 19 IS - 1-2 ER - TY - CHAP A1 - Breuer, Thomas ED - Heinemann, Thomas T1 - Finanzderivate und Agrar-Preisschwankungen BT - Gleichgewicht und Selbstreferenz T2 - Recht auf Leben. Recht auf Nahrung? N2 - Verstärkt der Handel mit Agrar-Derivaten die Preisschwankungen von Agrar-Produkten? In der politischen Diskussion wird diese These oft als Grund für eine strenge Reglementierung des Handels mit Agrar-Derivaten angeführt. Hier diskutiere ich die Voraussetzungen, auf denen verschiedene Argumente für diese These beruhen. Eine zentrale Rolle dabei spielen die Begriffe von Gleichgewicht und Selbstreferenz. Diese Begriffe spielen in der Logik und der Physik eine wichtige Rolle, haben aber in der Ökonomie erstaunliche Konsequenzen. Y1 - 2019 SP - 66 EP - 84 PB - Verlag Karl Alber CY - Freiburg ER - TY - CHAP A1 - Spettel, Patrick A1 - Beyer, Hans-Georg A1 - Hellwig, Michael T1 - Steady state analysis of a multi-recombinative meta-ES on a conically constrained problem with comparison to σSA and CSA T2 - FOGA '19. Proceedings of the 15th ACM/SIGEVO Conference on Foundations of Genetic Algorithms KW - constrained optimization KW - meta-evolution strategy KW - theoretical analysis Y1 - 2019 SN - 978-1-4503-6254-2 U6 - http://dx.doi.org/10.1145/3299904.3340306 SP - 43 EP - 57 PB - ACM CY - New York, NY, USA ER - TY - CHAP A1 - Pilsan, Horatiu O. A1 - Amann, Robert A1 - Gerstenberg, Markus ED - Hehenberger, Peter T1 - Realization of a small IIoT node. A Greenfield Approach BT - University of Applied Sciences Upper Austria. Wels, Austria. May 23-24, 2019 T2 - Proceedings of the 2019 20th International Conference on Research and Education in Mechatronics (REM 2019) KW - Industrial Internet of Things KW - Industry 4.0 KW - Greenfield Approach KW - Digitalization Y1 - 2019 U6 - http://dx.doi.org/10.1109/REM.2019.8744088 PB - Institute of Electrical and Electronics Engineers (IEEE.), Inc. CY - Danvers, MA ER - TY - BOOK ED - Unterkofler, Karl ED - Fetz, Thomas T1 - ÖMG Conference 2019 BT - Program and book of abstracts. University of Applied Sciences Vorarlberg, Dornbirn. September 16–20, 2019 Y1 - 2019 PB - Österreichische Mathematische Gesellschaft CY - Wien ER - TY - JOUR A1 - Entner, Doris A1 - Fleck, Philipp A1 - Vosgien, Thomas A1 - Münzer, Clemens A1 - Finck, Steffen A1 - Prante, Thorsten A1 - Schwarz, Martin T1 - A systematic approach for the selection of optimization algorithms including end-user requirements applied to box-type boom crane design JF - Applied System Innovation N2 - In engineering design, optimization methods are frequently used to improve the initial design of a product. However, the selection of an appropriate method is challenging since many methods exist, especially for the case of simulation-based optimization. This paper proposes a systematic procedure to support this selection process. Building upon quality function deployment, end-user and design use case requirements can be systematically taken into account via a decision matrix. The design and construction of the decision matrix are explained in detail. The proposed procedure is validated by two engineering optimization problems arising within the design of box-type boom cranes. For each problem, the problem statement and the respectively applied optimization methods are explained in detail. The results obtained by optimization validate the use of optimization approaches within the design process. The application of the decision matrix shows the successful incorporation of customer requirements to the algorithm selection. KW - optimization KW - algorithm selection KW - engineering design Y1 - 2019 U6 - http://dx.doi.org/10.3390/asi2030020 VL - 2. Jg. IS - H. 3 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Shuster, Gregory A1 - Leja, Marcis A1 - Unterkofler, Karl A1 - Jaeschke, Carsten A1 - Skapars, Roberts A1 - Gasenko, Evita A1 - Polaka, Inese A1 - Vasiljevs, Edgars A1 - Shani, Gidi A1 - Mitrovics, Jan A1 - Mayhew, Christopher A A1 - Haick, Hossam T1 - Non-contact breath sampling for sensor-based breath analysis JF - Journal of Breath Research N2 - Breath analysis holds great promise for real-time and non-invasive medical diagnosis. Thus, there is a considerable need for simple-in-use and portable analyzers for rapid detection of breath indicators for different diseases in their early stages. Sensor technology meets all of these demands. However, miniaturized breath analyzers require adequate breath sampling methods. In this context, we propose non-contact sampling; namely the collection of breath samples by exhalation from a distance into a miniaturized collector without bringing the mouth into direct contact with the analyzing device. To evaluate this approach different breathing maneuvers have been tested in a real-time regime on a cohort of 23 volunteers using proton transfer reaction mass spectrometry. The breathing maneuvers embraced distinct depths of respiration, exhalation manners, size of the mouth opening and different sampling distances. Two inhalation modes (normal, relaxed breathing and deep breathing) and two exhalation manners (via smaller and wider lips opening) forming four sampling scenarios were selected. A sampling distance of approximately 2 cm was found to be a reasonable trade-off between sample dilution and requirement of no physical contact of the subject with the analyzer. All four scenarios exhibited comparable measurement reproducibility spread of around 10%. For normal, relaxed inspiration both dead-space and end-tidal phases of exhalation lasted approximately 1.5 s for both expiration protocols. Deep inhalation prolongs the end-tidal phase to about 3 s in the case of blowing via a small lips opening, and by 50% when the air is exhaled via a wide one. In conclusion, non-contact breath sampling can be considered as a promising alternative to the existing breath sampling methods, being relatively close to natural spontaneous breathing. Y1 - 2019 U6 - http://dx.doi.org/10.1088/1752-7163/ab0b8d SN - 1752-7163 VL - 13. Jg. IS - H. 3/036001 ER - TY - THES A1 - Silberer, Katharina T1 - Datenbasierte Analyse des induktiven Aufwärmprozesses beim Aluminiumstrangpressen T1 - Analysis of induction heating during extrusion BT - Am Beispiel der Strangpresslinie P16 im UnternehmenHydro Extrusion Nenzing GmbH N2 - In den letzten Jahrzehnten gewann Aluminium als vielseitig einsetzbarer Werkstoff immer mehr an Bedeutung. Das Vorarlberger Unternehmen Hydro Extrusion Nenzing ist Teil der Aluminiumverarbeitungsindustrie und stellt stranggepresste Aluminiumprofile her. Beim Strangpressen werden Aluminiumstangen in einem Durchlaufinduktionsofen auf bis zu 520 °C erhitzt und anschließend durch ein formgebendes Werkzeug gepresst. Nach dem induktivem Aufwärmen wird ein Teil der Stange aus dem Ofen gefahren und abgeschert. Die erzeugte Temperaturverteilung an diesem abgescherten Bolzen ist der sogenannte Taper. Das induktive Aufwärmen ist ein wichtiger Teil der Extrusion und steht im Fokus dieser Forschungsarbeit. Ziel dieser Arbeit ist es, den Aufwärmprozess der Aluminiumstangen, mithilfe einer Kombination aus explorativer Datenanalyse und Methoden des maschinellen Lernens, genauer zu verstehen und den resultierenden Taper vorherzusagen. Außerdem werden parallel die signifikanten Einflussparameter, ohne Berücksichtigung von Materialparametern, untersucht. Nach der explorativen Datenanalyse wurden mithilfe eines k-means-Clusterverfahren zwei Klassifizierungsvarianten entwickelt. In der ersten Variante liegen die Taper nach ihrer Bolzenlänge und Form gegliedert vor. Es zeigte sich, dass die Taper der Bolzen mit ähnlicher Länge auch ähnliche Formen annehmen. Ein einfacher Entscheidungsbaum konnte die 13 Zielklassen zu etwa 85 % vorhersagen. Die Bolzenlänge spielt bei der Vorhersage eine wichtige Rolle. Die zweite Klassifizierungsvariante basiert hingegen ausschließlich auf der Taperform. Die angewendeten Modelle (k-Nearest-Neighbor, Decision Tree, Random Forest) waren jedoch kaum in der Lage, die 11 Klassen abzubilden. Grund für die unzureichende Vorhersageleistung können die vielen Unsicherheiten in der Datenstruktur sein. Die anschließende detaillierte, explorative Analyse der formabweichenden Taper deutet fehlende Merkmale im Datensatz an. Einige Bolzen setzen sich aus zwei Stangenenden zusammen. Diese geteilten Bolzen führen zu abweichenden Aufwärmverhalten, wodurch auffällige Taper entstehen. Die Information ob sich ein Bolzen aus zwei Stangen zusammensetzt fehlt jedoch im Datensatz. Der Aufwärmvorgang der Stangen wird demnach durch ein Wechselspiel der aktuellen Regelung und zwei maßgeblichen Faktoren beeinflusst: die Bolzenlänge und das Auftreten von geteilten Bolzen. Diese Faktoren bestimmen die Stangentemperatur im Ofen, den induzierten Strom und somit den resultierenden Taper. Aufgrund dieser Ergebnisse könnte die temperaturbasierte Regelung zukünftig durch eine Steuerung hinsichtlich des induzierten Stroms ersetzt, dadurch Energie eingespart und Schrott vermieden werden. N2 - Over the past decades, aluminum has gained significance as a widely applicable material in an array of industries. The company Hydro Extrusion Nenzing has been producing extruded aluminum solutions for over 40 years in Nenzing, Vorarlberg. In extrusion, aluminum billets are heated up till 520 ° C in an induction heater and then pressed through a forming die. The process of inductive heating is a vital aspect of extrusion and will be, next to the resulting taper, in focus within this research paper. The aim is to better comprehend the heating process of the aluminum billet by using explorative data analysis and by better understanding methods of machine learning. By doing this there will be a search for the significant influential parameters during the heating process and on the predictability of the taper. Parameters of material will not be considered here. Two categories emerged after the explorative analysis of the process data and the k-means-clustering: The first category classifies the taper by observing the billet length and the taper shape. It shows that the billet tapers with similar length take similar shapes. A decision tree could predict the dependent variables with an accuracy up to 85%. The billet length plays a vital role in the decision process. The second category however is solely focused on the shape of the taper. The applied models (k-nearest-neighbor, decision tree, random forest) were however barely able to display the 11 different classes. Reason for the insufficient predictability could be various insecurities in the data structure. A detailed, explorative data analysis points to a missing quality in the data sets. Various billets consist of two cutting edges from the aluminum rods. The split billet lead to derivations in the induced energy which creates derivative tapers. The information whether or not a billet is solid or combined from two cutting edges is missing as a variable in the data sets. The heating process of the billets is thus influenced by the interplay of the regulation of two factors: The billet length and additionally a splitted billet. Due to these results, the temperature based regulation could in the future be replaced through an electricity based control system, which would save energy and excess waste. KW - Extrusion KW - Aluminium KW - Explorative Datenanalyse KW - Machine Learning KW - Strangpressen Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3153 ER - TY - CHAP A1 - Finck, Steffen ED - Lopez-Ibanez, Manuel ED - Auger, Anne ED - Stützle, Thomas T1 - Worst case search over a set of forecasting scenarios applied to financial stress-testing T2 - Proceedings of the Genetic and Evolutionary Computation Conference Companion N2 - Stress testing is part of today’s bank risk management and often required by the governing regulatory authority. Performing such a stress test with stress scenarios derived from a distribution, instead of pre-defined expert scenarios, results in a systematic approach in which new severe scenarios can be discovered. The required scenario distribution is obtained from historical time series via a Vector-Autoregressive time series model. The worst-case search, i.e. finding the scenario yielding the most severe situation for the bank, can be stated as an optimization problem. The problem itself is a constrained optimization problem in a high-dimensional search space. The constraints are the box constraints on the scenario variables and the plausibility of a scenario. The latter is expressed by an elliptic constraint. As the evaluation of the stress scenarios is performed with a simulation tool, the optimization problem can be seen as black-box optimization problem. Evolution Strategy, a well-known optimizer for black-box problems, is applied here. The necessary adaptations to the algorithm are explained and a set of different algorithm design choices are investigated. It is shown that a simple box constraint handling method, i.e. setting variables which violate a box constraint to the respective boundary of the feasible domain, in combination with a repair of implausible scenarios provides good results. KW - risk management KW - simulation-based optimization KW - high-dimensional search space KW - constrained optimization KW - stress-testing Y1 - 2019 SN - 978-1-4503-6748-6 U6 - http://dx.doi.org/10.1145/3319619.3326835 SP - 1722 EP - 1730 PB - ACM CY - New York, NY, USA ER - TY - CHAP A1 - Mayer, Brigitte A1 - Heller-Künz, Helene ED - Sühl-Strohmenger, Wilfried ED - Tschander, Ladina T1 - Die Bibliothek als Ort des Lesens und Schreibens – illustriert am Beispiel des Schreibzentrums der Bibliothek der FH Vorarlberg T2 - Praxishandbuch Schreiben in der Hochschulbibliothek KW - Hochschulbibliothek KW - Schreibzentrum KW - Informationskompetenz KW - Schreibkompetenz KW - Schreibphasen Y1 - 2019 SN - 978-3-11-059414-0 U6 - http://dx.doi.org/10.1515/9783110594140-015 SP - 158 EP - 170 PB - De Gruyter Saur CY - Berlin ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Mit Mobile Learning die digitale Transformation der akademischen Lehre voranbringen JF - Die Neue Hochschule DNH N2 - Die digitale Transformation macht keineswegs halt vor der akademischen Lehre. Moderne Lehr-Lern-Arrangements nehmen Möglichkeiten der digitalen und der analogen Welt auf und nutzen die jeweiligen Stärken. KW - Mobile Learning Y1 - 2019 VL - o.Jg. IS - H. 6 SP - 28 EP - 31 ER - TY - CHAP A1 - Seyringer, Dana A1 - Sagmeister, Martin A1 - Maese-Novo, Alejandro A1 - Eggeling, Moritz A1 - Rank, Elisabet A. A1 - Edlinger, Johannes A1 - Muellner, Paul A1 - Hainberger, Rainer A1 - Drexler, Wolfgang A1 - Kraft, Jochen A1 - Koppitsch, Guenther A1 - Meinhardt, Gerald A1 - Vlaskovic, Marko A1 - Zimmermann, Horst ED - Jaworski, Marek ED - Marciniak, Marian T1 - Compact and high-resolution 256-channel silicon nitride based AWG-spectrometer for OCT on a chip T2 - ICTON 2019. 21st International Conference on Transparent Optical Networks. 9-13 July 2019, Angers, France N2 - We present design, simulation and technological verification of a compact 256-channel, 42-GHz silicon nitride based AWG-spectrometer. The spectrometer was designed for TM-polarized light with a central wavelength of 850 nm, applying “AWG-Parameters” tool. This design is based on a previous study of various AWG designs (8-channel, 100-GHz; 20-channel, 50-GHz; 40-channel, 50-GHz, 80-channel, 50-GHz and 160-channel, 50-GHz AWGs), which were all technologically verified. The spectrometer features small size and high resolution. It is integrated on OCT chip using standard CMOS processes. The SD-OCT system is developed to operate in a wavelength range from 800 nm to 900 nm, having 0.1 nm resolution. KW - Arrayed waveguide gratings KW - high-index contrast AWG KW - Si3N4 based AWG spectrometer KW - optical coherence tomography KW - OCT on-chip Y1 - 2019 SN - 978-1-7281-2779-8 U6 - http://dx.doi.org/10.1109/ICTON.2019.8840473 PB - National Institute of Telecommunications CY - Warsaw, Poland ER - TY - CHAP A1 - Werner, Tobias A1 - Mora, Carlos ED - Werth, Wolfgang T1 - Augmented Reality und Touch basierte Steuerung eines Roboters BT - Evolution von "Artour" T2 - Konferenz der Mechatronik Plattform Österreich 2019. "Machine Learnig and Data Science in der Mechatronik". Tagungsband. Villach, 21. November 2019. FH Kärnten, Campus Villach N2 - Ursprünglich wurde für das K-Projekt „LiTech“ eine mobile und intuitive Robotersteuerung – mit Touchbedienung und Augmented Reality – programmiert. Ziel war es, einen Industrieroboter spontan steuern zu können, mit besonderem Augenmerk auf Laienfreundlichkeit. Das System besteht aus einem Roboter und einem PC der als Bildschirm eine mit kapazitivem Touch ausgestattete und von einem Projektor bespielte Glasscheibe hat. Daten werden als String über eine serielle Schnittstelle übermittelt. Zur Erforschung der Nutzerfreundlichkeit werden Bälle auf einer Ebene hin- und herbewegt. Zur Cloud-Datenauswertung und Erstellung der Visualisierung wurden mittlerweile weitere Forschungszentren der FH Vorarlberg eingebunden. Im laufenden Wintersemester arbeitet ein Praktikant aus Südamerika an der Erweiterung auf den kompletten 3D-Raum mit möglicher Implementierung einer Gestensteuerung. Ziel des Beitrags ist es, den Versuchsaufbau und die Steuerung des Roboters zu beschreiben sowie geplante Weiterentwicklungen aufzuzeigen. KW - Roboter KW - Augmented Reality KW - Usability KW - Cloud KW - Touch Y1 - 2019 SN - 978-3-99076-100-7 SP - 28 EP - 29 PB - FH Kärnten CY - Villach ER - TY - JOUR A1 - Yuan, Xueyong A1 - Schwendtner, Michael A1 - Trotta, Rinaldo A1 - Huo, Yongheng A1 - Martín-Sánchez, Javier A1 - Piredda, Giovanni A1 - Huang, Huiying A1 - Edlinger, Johannes A1 - Diskus, Christian A1 - Schmidt, Oliver G. A1 - Jakoby, Bernhard A1 - Krenner, Hubert J. A1 - Rastelli, Armando T1 - A frequency-tunable nanomembrane mechanical oscillator with embedded quantum dots JF - Applied Physics Letters Y1 - 2019 U6 - http://dx.doi.org/10.1063/1.5126670 VL - 115. Jg. IS - H. 18/181902 ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Burtscher, Catalina A1 - Gaso, Peter A1 - Pudis, Dusan T1 - Design and simulation of polymer based photonic components T2 - 4th Global Summit & Expo on Laser Optics & Photonics 2019. Dubai, United Arab Emirates. 15 - 17 April 2019 N2 - Introducing 3D sub-micrometer technologies based on polymers opened new possibilities of design and fabrication of photonic devices and components in 3D arrangement. 3D laser lithography is direct writing process based on two photon polymerization exhibiting high accuracy and versatility, where numerous resists and even polymer ceramic mixtures can be used. We present design and simulation of polymer based photonic components with a focus on arrayed waveguide gratings (AWG) based on optical multiplexers/demultiplexers and optical splitters. All optical components were designed for 1550 nm operating wavelength, applying two commercial photonics tools. This study creates a basis for the design of optical components in 3D arrangement, which will be fabricated by 3D laser lithography. Y1 - 2019 ER - TY - CHAP A1 - Feilhauer, Thomas A1 - Finck, Steffen ED - Unterkofler, Karl ED - Fetz, Thomas T1 - Optimization with the Distributed Execution Framework T2 - ÖMG Conference 2019. Program and book of abstracts. University of Applied Sciences Vorarlberg, Dornbirn. September 16–20, 2019 Y1 - 2019 SP - 71 PB - ÖMG CY - Wien ER - TY - CHAP A1 - Chovan, Jozef A1 - Uherek, Frantisek A1 - Koza, Eduard A1 - Pavlov, Jozef A1 - Seyringer, Dana A1 - Gajdosova, Lenka ED - Jaworski, Marek ED - Marciniak, Marian T1 - Design and simulation of fiber to chip butt coupler for SiN integrated photonics T2 - ICTON 2019. 21st International Conference on Transparent Optical Networks. 9-13 July 2019, Angers, France N2 - SiN is a suitable material for fabricating of photonic integrated circuits with middle refractive index contrast for the visible and near infrared spectral region with ultra-low propagation losses. The paper deals with the design and simulation of fiber to SiN chip butt coupler with single step fabrication process without thickness tapering. Coupler is designed for 850 nm band for coupling between strip 0.25 μm × 1.00 μm waveguide and Nufern's 780-OCT single mode optical fiber with core diameter 4.4 μm. The coupling losses simulation results of the two simulation methods finite-difference beam propagation techniques and eigenmode expansion method are compared. Y1 - 2019 SN - 978-1-7281-2779-8 U6 - http://dx.doi.org/10.1109/ICTON.2019.8840203 PB - National Institute of Telecommunications CY - Warsaw, Poland ER - TY - CHAP A1 - Gajdosova, Lenka A1 - Seyringer, Dana A1 - Chovan, Jozef A1 - Uherek, Frantisek ED - Jandura, Daniel ED - Suslik, Lubos ED - Urbancova, Petra ED - Kovac, Jaroslav T1 - Design and simulation of silicon nitride based 16-channel 100-GHz arrayed waveguide Grating T2 - Proceedings of ADEPT 2019. 7th International Conference on Advances in Electronic and Photonic Technologies. Strbske Pleso, High Tatras, Slovakia. June 24 - 27, 2019 N2 - We present design and simulation of 16-channel, 100-GHz silicon nitride based AWG using BeamPROP simulation engine of RSoft photonic tool. The AWG was designed for TM-polarized light with central wavelength of 850 nm. The input design parameters were calculated applying AWG-Parameters tool. For this purpose, we created a ridge waveguide structure, used in the design of the AWG layout, and performed FEM simulation. The output of the BPM simulation of AWG structure are the transmission characteristics, which was used to calculate transmission parameters defining optical properties of simulated AWG. The achieved simulation results are in a good agreement with the design. KW - silicon nitride KW - arrayed waveguide grating KW - design and simulation Y1 - 2019 SN - 978-80-554-1568-0 SP - 151 EP - 154 PB - University of Zilina in EDIS-Publishing Centre of UZ CY - Zilina ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Chovan, Jozef A1 - Figura, Daniel A1 - Uherek, Frantisek ED - Jandura, Daniel ED - Suslik, Lubos ED - Urbancova, Petra ED - Kovac, Jaroslav T1 - Comparison of silicon nitride based 8-channel 100-GHz AWGs applying different waveguide structures T2 - Proceedings of ADEPT 2019. 7th International Conference on Advances in Electronic and Photonic Technologies. Strbske Pleso, High Tatras, Slovakia. June 24 - 27, 2019 N2 - This paper presents design and simulation of 8-channel, 100-GHz AWGs based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. AWGs were designed for central wavelength of 850 nm applying AWG-Parameters tool. The simulations were performed applying FEM and BPM methods in RSoft and PHASAR photonic tools. The simulation results show considerably lower losses but slightly higher channel crosstalk when applying rib waveguides. KW - arrayed waveguide gratings KW - AWG design KW - silicon nitride KW - rib waveguides KW - ridge waveguides Y1 - 2019 SN - 978-80-554-1568-0 SP - 215 EP - 218 PB - University of Zilina in EDIS-Publishing Centre of UZ CY - Zilina ER - TY - BOOK A1 - Abawi, Daniel F. A1 - Ahrens, Volker A1 - Bäßler, Rudolf A1 - Brettel, Malte A1 - Dittmann, Uwe A1 - Englberger, Hermann A1 - Hildebrand, Wolf-Christian A1 - Leipnitz-Ponto, Yvonne A1 - Merchiers, Andreas A1 - Olsowski, Gunter A1 - Pumpe, Dieter A1 - Schätter, Alfred A1 - Schmager, Burkhard A1 - Schuchardt, Christian A1 - Hirschhausen, Christian von A1 - Werner, Matthias A1 - Zadek, Hartmut ED - Fakultäten- und Fachbereichstag Wirtschaftsingenieurwesen e.V., ED - Verband Deutscher Wirtschaftsingenieure (VWI) e.V., T1 - Qualifikationsrahmen Wirtschaftsingenieurwesen N2 - Qualifikationsrahmen, Wirtschaftsingenieurwesen KW - WING, Wirtschaftsingenieurwesen Y1 - 2019 UR - https://www.steinbeis-edition.de/out/pictures/media/207665_blick.pdf PB - Steinbeis-Edition CY - Stuttgart ET - 3., aktualisierte Auflage ER - TY - CHAP A1 - Hasko, Daniel A1 - Chovan, Jozef A1 - Uherek, Frantisek A1 - Seyringer, Dana A1 - Gajdosova, Lenka ED - Jandura, Daniel ED - Suslik, Lubos ED - Urbancova, Petra ED - Kovac, Jaroslav T1 - Automated optical fibers coupling to photonic integrated circuits T2 - Proceedings of ADEPT 2019. 7th International Conference on Advances in Electronic and Photonic Technologies. Strbske Pleso, High Tatras, Slovakia. June 24 - 27, 2019 N2 - The photonic integrated circuits are required in the next generations of coherent terabit optical communications. The software tools for automated adjustment and coupling of optical fiber arrays to photonic integrated circuits has been developed. The obtained results are needed in final production phase in the technology process of photonic integrated circuits packaging. KW - optical communication systems KW - integrated photonics KW - photonics integrated circuit Y1 - 2019 SN - 978-80-554-1568-0 SP - 273 EP - 276 PB - University of Zilina in EDIS-Publishing Centre of UZ CY - Zilina ER - TY - CHAP A1 - Moosbrugger, Robert ED - Perlik, Manfred ED - Galera, Giulia ED - Machold, Ingrid ED - Membretti, Andrea T1 - Migrant social inclusion: experiences from the Bregenzerwald and EU-funded projects T2 - Alpine refugees N2 - The chapter illustrates social inclusion processes based on experiences of the PlurAlps project in Bregenzerwald, Austria. KW - Migration Y1 - 2019 SN - 978-1-5275-3672-2 SP - 121 EP - 125 PB - Cambridge Scholars Publishing CY - Newcastle upon Tyne ER - TY - CHAP A1 - Gajdosova, Lenka A1 - Seyringer, Dana A1 - Gaso, Peter A1 - Jandura, Daniel A1 - Pudis, Dusan ED - Sitek, Jozef ED - Vajda, Jan ED - Jamnicky, Igor T1 - Design, simulation and technological realization of polymer based 3D 1x4 splitter T2 - Applied Physics of Condensed Matter (APCOM 2019). Strbsko Pleso, Slovak Republic. 19-21 June 2019 Y1 - 2019 SN - 978-0-7354-1873-8 U6 - http://dx.doi.org/10.1063/1.5119465 IS - 2131/020012 PB - AIP Publishing CY - Melville, NY ER - TY - CHAP A1 - Dobler, Martin A1 - Ballandies, Mark A1 - Holzwarth, Valentin T1 - On the extension of digital ecosystems for SCM and customs with distributed ledger technologies BT - Requirements analysis, innovation assessment, and prototype design for the Lake Constance Region T2 - 2019 IEEE International Conference on Engineering, Technology and Innovation (ICE/ITMC). Co-creating our Future: Scaling-up Innovation Capacities through the Design and Engineering of Immersive, Collaborative, Empathic and Cognitive Systems. Sophia Antipolis Innovation Park, FRANCE. 17-19 June 2019 N2 - Global supply chains represent the backbone of the modern manufacturing industry. Planning of global supply chains still represents a major hurdle, mainly because of the high complexity and unforeseen disruptions that have to be mastered for meeting the different logistics windows in a globally distributed production environment. Trust in supply chains is an additional challenge. A major – albeit sometimes overlooked - part of Supply Chain Management (SCM) is the management and integration of customs processes, clearing of tariffs, (re-)billing of customers, and fulfilling other legal requirements related to crossing borders, ranging from environmental standards over goods inspection to general paper work. With the exception of work offered by the World Customs Organization (WCO) the issue of customs and blockchain is still underrepresented in research and practice. In this paper, we look at innovations that drive the current ICTenabled SCM research and how these can be combined with smart customs management. After a literature review and introduction to the state-of-the-art, we list potential trust-based innovations for SCM and customs in digital business ecosystems. Based upon the innovations we also describe a requirements analysis of existing distributed ledger technologies (requirements for system layout, system configuration, system governance). A description of the prototype for the Lake Constance region – on which we are currently working – concludes the paper. KW - Blockchain KW - Supply Chain Management KW - Customs KW - Digital Ecosystems KW - Digital Business Ecosystems Y1 - 2019 SN - 978-1-7281-3401-7 U6 - http://dx.doi.org/10.1109/ICE.2019.8792646 PB - Institute of Electrical and Electronics Engineers, Inc. (IEEE) CY - Danvers, MA ER - TY - JOUR A1 - Rizzarelli, Paola A1 - Piredda, Giovanni A1 - La Carta, Stefania A1 - Mirabella, Emanuele Francesco A1 - Valenti, Graziella A1 - Bernet, Ramona A1 - Impallomeni, Giuseppe T1 - Characterization and laser-induced degradation of a medical grade polylactide JF - Polymer Degradation and Stability N2 - In this study, we carried out the structural and thermal characterization of a medical-grade poly (lactide) (PLA) by SEC, TGA, DSC, NMR, ICP-MS and Py-GC/MS. Moreover, we investigated the laser-induced degradation occurring when ultrashort laser pulses (ULP) were employed to cut extremely thin polymer films prepared by solvent-casting. ULP polymer cutting technology is an interesting manufacturing process for its advantages in potential medical applications. In fact, heat transmission to the region surrounding the cuts is limited, so that the incisions are precise and the effects on the regions around them are small. In this way, the need for post-processing is reduced and ULP cutting becomes interesting for industrial applications. However, degradation induced by ULP may occur and compromise the properties of the polymer samples. To investigate this possibility, portions of PLA films, ultrashort laser cut (ULC) and uncut, were analysed by SEC, DSC, NMR and FTIR. Furthermore, PLA oligomers were studied by ESI-MS. Both SEC and NMR showed a decrease in the molecular weight. FTIR, ESI-MS and NMR spectra revealed the presence of olefin end groups originated from a \beta-H transfer mechanism, induced by heat and/or light (Norrish II mechanism). Additionally, the inspection of the ESI mass spectra highlighted the cleavage of ester bonds related to the Norrish I type mechanism, undetected by the other techniques. KW - Biodegradable polymers KW - Ultrashort pulses microfabrication Y1 - 2019 U6 - http://dx.doi.org/10.1016/j.polymdegradstab.2019.108991 VL - o.Jg. IS - Bd. 169/108991 ER - TY - CHAP A1 - Laubender, Elmar A1 - Matylitskaya, Volha A1 - Kostal, Elisabeth A1 - Kasemann, Stephan A1 - Urban, Gerald A. A1 - Partel, Stefan A1 - Dincer, Can T1 - Gold nanogap interdigitated arrays for redox cycling amplified dopamine detection T2 - 2019 20th International Conference on Solid-State Sensors, Actuators and Microsystems & Eurosensors XXXIII (TRANSDUCERS & EUROSENSORS XXXIII). 23-27 June. Berlin. Germany N2 - Here we present the highly sensitive detection of dopamine using gold nanogap IDAs with redox-cycling amplification. Through the combination with a facile electrochemical activation and a chronoamperometric multistep protocol fouling of the gold electrode surface can be prevented and a sensitivity of 14 nA μM -1 with excellent linearity up to 10 μM is achieved. The low-cost and reproducible wafer level fabrication process of the nanogap IDAs plays a key role. Electrode and substrate materials can be nearly arbitrarily chosen. Also the gap sizes could be adjusted down to sub-100 nm dimensions with this versatile approach, allowing for very high signal amplification. In comparison to the current gold standard, fastscan cyclic voltammetry (FSCV) with carbon fiber microelectrodes (CFMEs), which suffers from high background currents, no elaborate data processing and high-end electronic equipment is needed. Employing our flexible, easy and inexpensive method, DA monitoring with a short acquisition period and a detection limit less than 200 nM is successfully demonstrated. KW - Electrodes KW - Gold KW - Electric potential KW - Protocols KW - Fingers KW - Sensitivity KW - Monitoring Y1 - 2019 SN - 978-1-7281-2007-2 U6 - http://dx.doi.org/10.1109/TRANSDUCERS.2019.8808356 SP - 1017 EP - 1020 PB - IEEE CY - Danvers, MA ER - TY - CHAP A1 - Seyringer, Dana A1 - Chovan, Jozef A1 - Gajdosova, Lenka A1 - Figura, Daniel A1 - Uherek, Frantisek ED - Jaworski, Marek ED - Marciniak, Marian T1 - Comparison of silicon nitride based 1x8 Y-branch splitters applying different waveguide structures T2 - ICTON 2019. 21st International Conference on Transparent Optical Networks. 9-13 July 2019, Angers, France N2 - This paper presents design, simulation and optimization of 1x8 Y-branch power splitters based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. The splitters were designed for 850 nm spectral optical window and the simulations were performed applying FEM and BPM methods in RSoft photonic tool. The aim of this work was to find minimum physical dimensions of the designed splitters occupying minimal space on PIC chip. The optimization was done with regards to high symmetrical splitting ratio and low insertion loss. Finally, the optical properties of both splitters were studied and compared with each other. KW - silicon nitride KW - rib waveguide KW - ridge waveguide KW - Y-branch KW - power splitter Y1 - 2019 SN - 978-1-7281-2779-8 U6 - http://dx.doi.org/10.1109/ICTON.2019.8840394 PB - National Institute of Telecommunications CY - Warsaw, Poland ER - TY - CHAP A1 - Partel, Stefan A1 - Matylitskaya, Volha T1 - Carbon nanogap electrode arrays for electrochemical sensors and biosensors T2 - 45th International Conference on Micro & Nano Engineering. Going Nano in Homer's Land. Rodos Palace Hotel, Rhodes Greece. September 23rd - 26th, 2019 N2 - We report resent results on the fabrication and characterization of carbon nanogap interdigitated electrode arrays (IDAs) for biosensor applications based on redox cycling. The electrochemical results of the carbon electrodes are compared to our fabricated gold electrodes with similar nanogap distances. The amplification factor and the collection efficiency were recorded by chronoamperometry. Cyclic voltammetry (CV) was utilized to determine the oxidation and reduction potentials as well as for monitoring the electron transfer process. The different deposited carbon materials were characterized by Raman spectroscopy.At present, we successfully fabricated carbon nanogaps down to 80 nm and we are convinced to reach the present fabrication limit of about 30 nm (for gold and platinum electrodes) with carbon as electrode material as well. To the best of our knowledge, this is the first IDA nanogap sensor, which features a gap distance under 100 nm with amorphous carbon as electrode material. Moreover, we present a signal amplification of 32 for carbon electrodes by redox cycling, which is the highest reported amplification so far. KW - carbon KW - IDA KW - electrochemical biosensor KW - redox cycling KW - nanogap KW - lift-off free Y1 - 2019 ER - TY - CHAP A1 - Arnold, Lukas T1 - Der Pius-Verein zur Förderung der katholischen Presse in Tirol von 1906 bis 1914 T2 - Zeit - Raum - Innsbruck N2 - Der Presse kam zu Beginn des 20. Jahrhunderts eine außerordentlich wichtige Rolle in der Auseinandersetzung zwischen den politischen Lagern, Sozialdemokratie, Deutschnationalismus und Christlich-Soziale Bewegung zu. Jedes der drei Lager hatte ihm mal mehr mal weniger zugeordnete Zeitungen, die reichsweit erschienen oder kleinere Lokal- und Provinzblätter waren. Der Pius-Verein zur Unterstützung der katholischen Presse engagierte sich in dieser Auseinandersetzung für die Sache des politischen Katholizismus. Seine Methoden bestanden in der politischen Agitation und im Sammeln von Spenden für katholische Zeitungen. Im Kronland Tirol war einer der aktivsten Ableger des Pius-Vereins tätig, mit Ortsgruppen in fast jeder Gemeinde. KW - Beginn des 20. Jahrhunderts KW - Sozialgeschichte KW - politischer Katholizismus Y1 - 2019 SN - 978-3-7030-1092-7 SP - 81 EP - 103 PB - Universitätsverlag Wagner CY - Innsbruck ER - TY - THES A1 - Spettel, Patrick T1 - Evolution strategies for constrained optimization KW - Evolution Strategies KW - Black-box Optimization KW - Constrained Optimization KW - Theoretical Analysis Y1 - 2019 U6 - http://dx.doi.org/10.18725/OPARU-24371 ER - TY - THES A1 - King, David T1 - Mikrotomographische Visualisierung struktureller Auswirkungen der zyklischen Alterung auf zylindrische Lithium-Ionen Akkumulatorzellen in Powerbanks T1 - Micro-tomographic visualization structural effects of cycling aging on cylindrical lithium-Ion batteries in powerbanks N2 - Alterungsvorgänge in einer Lithium-Ionen Akkumulatorzelle beeinflussen deren Eigenschaften und sind daher von besonderen Bedeutung für den Einsatz dieser Technologie. Diese Masterarbeit untersucht mikrostrukturelle Veränderung in zwei zylindrischen Lithium-Ionen Zellen (Type 26650) ohne Zentrierstift, die in Powerbanks verbaut sind. An den beiden Akkumulatoren, mit unterschiedlichen Alterungszustands, wird vergleichend beobachtet welche Unterschiede sich über die Alterung ergeben. Mittels Computertomographie und elektrischen Messungen wurden Daten während der zyklischen Alterung der Zellen gesammelt und ausgewertet. Es konnte gezeigt werden, dass der Verlauf des Kapazitätsverlustes abhängig vom Alterungszustand ist. Insgesamt ergab sich nach 507 Zyklen bei der Powerbank „Neu“ eine Reduzierung der aufgenommenen Energie um 16 % und der abgegebenen Energie um 20 %. Die Powerbank „Alt“ zeigte nach 317 Zyklen eine Reduzierung der aufgenommenen Energie von 19% und der abgegebenen Energie von 27% zum Ausgangswert. Der gemessene Kapazitätsverlust konnte nicht auf mikrostrukturelle Veränderungen während der Alterung zurückgeführt werden. Es zeigten sich besonders in der bereits gealterten Zelle (Powerbank „Alt“) deformierte Elektrodenschichten im Zellinneren und in der Näher der Stromableiter. Hinzukommt bei der Powerbank „Alt“, dass Kathode und Anode gegeneinander verschoben sind. Es konnte ebenfalls in der Powerbank „Alt“ eine neu entstandene Deformierung während der zyklischen Alterung beobachtet werden. Des Weiteren konnten auch Schweißgrate bei beiden Powerbanks auf den Stromableitern visualisiert werden. N2 - Aging affects the characteristics of a lithium-ion battery and is therefore very relevant for the use of this technology. This master thesis analyses micro-structural changes in two cylindrical lithium-ion cells (Type 26650) without center pin which are used in two powerbanks. Both powerbanks had different used cycles and their aging was compared to see which differences arise over aging. With the use of computer tomography and electrical measurements data was collected during cycling aging. It could be shown that the course of the capacity loss is dependent on the aging state of the cell. In total the reduction of the input energy was 16 % and the output energy was 20% in powerbank “Neu“ after 507 cycles. Powerbank “Alt“ showed a reduction of the input energy of 19% and the output energy of 27% compared to the initial value after 317 cycles. The measured capacity loss could not be ascribed to microstructural changes during aging. However, especially in the already aged cell (powerbank "Alt") deformed electrode layers were found inside the cell and near the battery tab. Furthermore the cathode and anode are shifted against each other in powerbank "Alt". It could also be observed a newly formed deformation in the powerbank "Alt" during cycling aging. Additionally welding burrs on the battery tabs could be visualized in both powerbanks. KW - Lithium - Ionen KW - Akkumulator KW - Mikrocomputertomographie KW - Zellalterung Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3194 ER - TY - THES A1 - Unterkofler, Nathalie T1 - Auswirkung auf das Pflanzenwachstum und die Anzahl der Mikroorganismen, unter Laborbedingungen, durch die Einbringung oberflächenaktivierter Biokohle aus einer Holz-Vergasungsanlage in Böden mit unterschiedlichen Kohlegehalten T1 - Effect on plant growth and number of microorganisms under laboratory conditions by incorporating surface-activated biochar from a wood gasification plant in soils with different carbon contents N2 - In Anbetracht einer immer größer werdenden Diskussion über den Klimaschutz und einer anvisierten Energiewende finden umweltschonende Energietechniken immer mehr an Aufmerksamkeit in der Gesellschaft. Die Kombination von Stromerzeugung und gleichzeitiger Wärmeproduktion macht die Biomassevergasung zu einem interessanten Untersuchungsobjekt. Die anfallenden Biokohlestäube versprechen in Zukunft von großem Nutzen zu sein, um zum Beispiel Kohlenstoff in der Erde abzuspeichern. Die sogenannten ”Terra Preta“ Böden steigerten merklich das Interesse am Einsatz von Kohle in der Landwirtschaft, um in Böden verbessernde Eigenschaften zu erzielen. In dieser Masterarbeit wird die Auswirkung der Biokohle einer Schwebefestbettvergaseranlage auf das Pflanzenwachstum, die verfügbaren Nährstoffe und auf die Anzahl der Mikroorganismen untersucht. Hierfür wurden zwei verschiedene Versuchspflanzen herangezogen. Es wurde auf Hafer und Rübse zurückgegriffen. Der Versuch fand unter Laborbedingungen in einem Wachstumsschrank statt. Es wurden Böden mit unterschiedlichen Kohlegehalten hergestellt (0 %, 2,5 % 5 %, 12,5 %). Des Weiteren wurde auf zwei verschiedene Arten eine oberflächenaktivierte Kohle hergestellt. Einmal erfolgte dies durch Ko-Kompostierung der Biokohle in Grünschnitt und das zweite Mal durch die Beladungmit künstlichem Dünger. Die chemische Aktivierung erfolgte über einen Rührversuch. Dabei wurde die Kohle über einen längeren Zeitraum mit dem künstlichen Dünger in einem Gefäß gerührt. Die Versuchsdauer erstreckte sich jeweils über einen Zeitraum von ca. 3 Wochen. Am Ende der Versuche wurden die Pflanzen geerntet. Anschließend wurde ihre Wuchshöhe und deren Durchmesser erfasst und statistisch ausgewertet. Die Nährstoffe im Boden wurden mittels Macherey Nagel Schnelltest ermittelt. Hierfür wurden Proben sowohl am Anfang als auch am Ende des Experiments genommen und anschließend aufbereitet und ebenfalls statistisch ausgewertet. Es konnte durch den Zusatz von Kohle einen signifikant höherer Mittelwert des Pflanzenwachstums erzielt werden. Und auch bei den Nährstoffen konnten Unterschiede zum Referenzboden nachgewiesen werden. Im Gegensatz dazu konnte bei den Mikroorganismen statistisch kein Unterschied festgestellt werden. Leider traten während des Versuches vermehrt Probleme auf, die aber entsprechend in der Arbeit adressiert und dokumentiert werden. Aus diesem Grund muss darauf verwiesen werden, dass einige Ergebnisse nicht verwertbar waren. N2 - Climate change and environmentally friendly energy technologies gather a lot of attention nowadays. The combination of producing electricity and heat makes the biomass gasification process for further investigations desirable. An unplanned by-product is biochar. The obtained coal promises to be useful for storing carbon in the soil. The so-called ”Terra Preta“ soil marked the beginning of an increasing interest for the use of biochar in agriculture. The incorporation should enhance the soil-improving properties. In this master thesis, we analyse the effect of biochar as a soil amendment, on plant growth, the available nutrients and the number of microorganisms. For this purpose,two different test plants (oat and turnip rape) were used. The experiment took place under laboratory conditions in a growing chamber. The tests based on soils with different carbon contents (0 %, 2.5 %, 5 %, 12.5 %). Furthermore, there were two different types of surface-activated coal produced. The first one was done by co-composting the biochar in green waste and the second one by loading it with artificial fertilizer. The chemical activation took place with the help of a stirring test. The coal was stirred in a vessel over a long period of time with an artificial fertilizer.The general test duration took place over a period of 3 weeks. At the end of the experiment, the plants were harvested. During the procedure, they were measured in height and their diameter was recorded and statistically evaluated. The nutrients in the soil were determined using the Macherey and Nagel rapid test. For this purpose, samples were taken both at the beginning and at the end of the experiment. The samples were evaluated with the help of statistical methods. KW - Biokohle KW - Holzvergasung KW - Boden KW - Pflanzen KW - Versuch Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3155 ER - TY - THES A1 - Gopp, David T1 - Einflussgrößen bei der modellbasierten Prüfung von kapazitiven Spannungswandlern BT - Was sind die einflussreichsten Parameter der modellbasierten Prüfung von kapazitiven Spannungswandlern und wie wirken sich diese auf den Übersetzungs- und Phasenfehler aus? N2 - Das exakte Messen der aktuellen Spannung ist ein essenzieller Baustein sowohl für die Versorgungssicherheit als auch die Verrechnung von Leistung in der elektrischen Energietechnik. Dazu werden verschiedene Geräte verwendet, welche die Spannung auf einen normierten Wert teilen, sodass diese problemlos gemessen werden kann. In dieser Masterarbeit werden in weiterer Folge lediglich die konventionellen Spannungswandler und deren Übertragungsfehler, genauer gesagt die kapazitiven Spannungswandler, im Detail analysiert. Das übergeordnete Ziel dieser Arbeit ist es, jene Parameter der modellbasierten Messung von kapazitiven Spannungswandlern zu finden, welche die größte Sensitivität im Bezug auf den Spannungsübersetzungs-und Phasenfehler sind. Dabei werden zuallererst die zwei gängigsten Messmethoden zur Prüfung der Genauigkeit von konventionellen Spannungswandlern diskutiert. Des Weiteren wird die Arbeit anhand der CIGRE Umfragen im Bezug auf die Ausfälle der konventionellen Wandler motiviert. Des Weiteren wird der Stand der Technik ermittelt und dargelegt. Für die Dauer der Untersuchung wurde ein kapazitiver Spannungswandler in seine beiden Hauptkomponenten (induktiver und kapazitiver Teil), zwecks besserer Analysierbarkeit der einzelnen Komponenten, zerlegt. Somit konnten sowohl die einzelnen CVT Komponenten als auch der gesamte kapazitive Spannungswandler frequenzabhängig und spannungsabhängig untersucht werden. Mittels dieser und der modellbasierten Messungen wurden die einzelnen Parameter für die Simulationsumgebung des kapazitiven Spannungswandlers ermittelt. Im Anschluss wurde dieses zum einen mittels vier verschiedener Betriebszustände und zum anderen mittels Messergebnissen sowohl der modellbasierten Prüfung als auch der Primärprüfung (EPRO Kalibrierung) verifiziert. Mit dieser Grundlage wurden anschließend die verschiedenen Sensitivitätsanalysen durchgeführt. N2 - Exact measurement of the network voltage is an essential component for both supply reliability and the billing of power in electrical power engineering. Various assets, which transform the voltage to a standardized value that can be measured, are used for this purpose. In this master thesis, only the conventional voltage transformers and their transmission errors, more precisely the capacitive voltage transformers, are analyzed in detail. The main goal of this thesis is to find those parameters of the model based capacitive voltage transformer measurement which are the most sensitive to the translation errors. First of all, the two most common measurement methods for testing the accuracy of conventional voltage transformers are discussed. In addition to this, the work is motivated by the CIGRE surveys with regard to the failures of conventional transformers. Furthermore, the state of the art is determined and presented. For the duration of the investigation, a capacitive voltage transformer was divided into its two main components (inductive and capacitive part) in order to improve the analyzability of the individual components. Thus, both the individual CVT components and the entire capacitive voltage transformer could be examined frequency-dependent and voltage-dependent. These, and model-based measurements, were used to determine the individual parameters for the simulation environment of the capacitive voltage transformer. This was then verified using four different operating states on the one hand and measurement results from both the model-based test and the primary test (EPRO calibration) on the other. The various sensitivity analyses were then carried out on this basis. KW - Spannungswandler KW - Messmethoden KW - Sensitivität KW - Spannung KW - Simulation Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3147 ER - TY - THES A1 - Berghaus, Julia T1 - Datenbank und Rechentool für Sanierungsmaßnahmen für Einfamilienhäuser N2 - Das Energieinstitut Vorarlberg hat zusammen mit mehreren Regionen in Vorarlberg das Sanierungslotsenprojekt gestartet, um die Beratungssituation bei der Gebäudesanierung zu verbessern. Durch wiederholten Kundenkontakt wurde festgestellt, dass es ein Beratungsdefizit für Besitzer älterer Einfamilienhäuser gibt. Zwischen der Erkenntnis, dass eine Sanierung des Gebäudes notwendig ist und dem Zeitpunkt, an dem die ersten Leistungen bestellt werden, gibt es keine sachkundige Betreuung in den Fragestellungen der zukünftigen Gebäudenutzung. In den bisher angebotenen Beratungen werden zwar auch unterschiedliche Sanierungsvarianten miteinander verglichen. Jedoch bezieht sich der Vergleich auf Variationen von Sanierungsmaßnahmen, wie beispielsweise Dämmstoff - und Fensterqualität oder die Auswahl eines Heizungssystems. Darüber hinaus gehende Fragen über altersgerechtes Wohnen, Generationenwohnen, Nachverdichtung und Vermietung werden in diesen Beratungen nicht behandelt. In allen Fragen der zukünftigen Nutzung und den zukünftigen Anforderungen an das Gebäude, den darauf abgestimmten Sanierungszielen und der zugehörigen Kostenschätzung mit Finanzierungsberechnung sind die Besitzer auf sich gestellt. Deshalb ist der Bedarf nach einem einfachen Rechentool, welches in einer frühen Phase der Sanierungsberatung, eine schnelle Berechnung der in Betracht kommenden Sanierungsvarianten ermöglicht, entstanden. In dieser frühen Phase ist es bislang nicht üblich eine Kostenschätzung abzugeben. Für diese Berechnungen wird eine Datenbank mit Sanierungs - und Umbaukostenelementen benötigt, sodass mit einer abgesicherten Basisdaten kalkuliert werden kann. In der vorliegenden Masterarbeit werden eine auf Microsoft Excel basierende Datenbank und das dazugehörige Rechentool vorgestellt, die die beschriebenen Anforderungen erfüllen. Mit Hilfe der Datenbank wird eine Grundlage geschaffen, an denen sich die Sanierungslotsen orientieren können. Zusätzlich zu den Netto- und Bruttokosten, die bei den einzelnen Sanierungsmaßnahmen anfallen, werden auch Einheitskosten angegeben, die in das Rechentool eingetragen werden können. Das Rechentool ermöglicht den Vergleich von fünf unterschiedlichen Sanierungsvarianten. Durch die freie Eingabe der Flächen können auch Varianten mit unterschiedlichen Nutzungskonzepten und unterschiedlichen Grundrissen verglichen werden. Neben einer Grobkostenrechnung der Sanierungskosten erfolgt im Tool auch die Berechnung der Förderung laut der Wohnaussanierungsrichtlinie und Energieförderungsrichtlinie des Landes Vorarlberg. Weitere Förderungen können als Einmalzuschüsse eingetragen werden. Eine vereinfachte Wirtschaftlichkeitsbetrachtung erfolgt über die Berechnung der Finanzierung der Sanierung. Hierbei werden auch Einnahmen durch Vermietung berücksichtigt. N2 - The “Energieinstitut Vorarlberg” together with several regions in Vorarlberg has started the project “Sanierungslotsen” to improve the consulting situation for building refurbishment. By repeated customer contacts it was determined that there is a consulting deficit for owners of older single family houses. Between the realization that a refurbishment of the building is necessary and the time, at which the first services are ordered, there is no competent support in the questions of the future usage of the building. In the consultations offered up to now different refurbishment variants are compared with each other. However, the comparison refers to variations of refurbishment measures, such as insulation material and window quality or the selection of a heating system. However, questions going beyond including age - appropriate living, generation living, densification and leasing are not covered in these consultations. In all questions of the future usage and the future requirements of the building, the coordinated goals of the refurbishment and the associated cost estimate with financing calculation the owners are on their own. Therefore, there is a need for a simple calculation tool, which allows a quick calculation of the considered refurbishment variants in an early phase of the refurbishment consultation, in which it was not yet usual to give cost estimates. For these calculations, a database with refurbishment and reconstruction cost elements is also required, so that calculations can be made with a secured basic data. In the present master thesis, a database and the corresponding Calculation tool based on Microsoft Excel are presented, which fulfil the described requirements. With the help of the database a basis is created which the “Sanierungslotsen” can use as orientation basis. In addition to the net and gross costs incurred in the individual refurbishment measures, unit costs are also specified, which can be entered in the calculation tool. The calculation tool makes it possible to compare five different refurbishment variants. By the free input of the surfaces also variants with different usage concepts and layouts can be compared. In addition to a rough cost calculation of the refurbishment costs, the tool also calculates the subsidy according to the Housing Rehabilitation Directive and the Energy Subsidy Directive of the State of Vorarlberg. Further subsidies can be entered as one - time grants. A simplified profitability analysis is carried out by calculating the financing of the refurbishment. Income from leasing is also taken into account. KW - Sanierung KW - Sanierungsmassnahmen KW - Datenbank KW - Rechentool KW - Einfamilienhäuser Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3143 PB - FH Vorarlberg ER - TY - THES A1 - Koch, Florian T1 - Untersuchung zur Kostenminimierung in einem PV to Vehicle to Grid System am Beispiel eines betrieblichen Fuhrparks in Österreich T1 - Investigation to minimize costs in a PV to Vehicle to Grid System using the example of a company fleet in Austria N2 - Um ein möglichst kostengünstiges Laden von Elektrofahrzeugen zu erreichen, ist es nötig, diese möglichst in Zeiten zu laden, an denen die Kosten für die Energie geringer sind und die Entstehung von Leistungsspitzen vermieden wird. Aus diesem Grund wird in dieser Arbeit anhand des Verbrauches und den tariflichen Bedingungen eines Betriebes in Österreich die Kostenentwicklung von drei verschiedenen Ladeszenarien untersucht und verglichen. Dabei handelt es sich um das einfache Laden, intelligente Laden und das intelligente Laden mit Vehicle to Grid Erweiterung, wobei hierbei die Energie aus den Fahrzeugen ausschließlich zur Eigenverbrauchsoptimierung und Spitzenlastreduktion eines Betriebes dient und somit nicht in das Netz gespeist wird. Die Ergebnisse werden durch eine lineare Optimierung errechnet wobei bis zu vier Fahrzeuge simuliert werden. Die Ergebnisse zeigen, dass es durch das intelligente Laden zu keinen neuen Leistungsspitzen kommt und es zusätzlich zu einem erhöhten Eigenverbrauch aus der vorhandenen Photovoltaikanlage kommt. Dadurch reduzieren sich die Ladekosten in jedem Szenario. Auch in Betrachtung auf die Anschaffungskosten, ist eine Verbesserung ersichtlich. Beim Vehicle to Grid Laden werden die Arbeits- und Leistungskosten noch weiter gesenkt, wobei die Leistungskosten bei zwei Fahrzeugen ihren Tiefpunkt erreicht haben. Zusätzlich kann der Eigenverbrauch aus der Photovoltaikanlage noch weiter erhöht werden. Nachdem hierbei die Investitionskosten noch berücksichtigt wurden, kommt der Autor zum Schluss, dass es nur mit einem Fahrzeug zu einer Verringerung der gesamten Kosten kommt. Dies kommt durch die erhöhten Investitionskosten und dem mit höher werdender Anzahl an Fahrzeugen geringer werdenden Vehicle to Grid Einsatz zustande. N2 - In order to achieve the most cost-effective charging of electric vehicles, it is necessary to charge them at times of low energy cost. This is accomplished by reducing the energy demand from the grid, by increasing the self-consumption of photovoltaic energy and by reducing peak power demand. In this work three different charging scenarios are compared on base of the costs. The compared charging scenarios are simple charging, intelligent charging and vehicle to grid enabled intelligent charging. With vehicle to grid it is meant that the energy is only used for self-consumption and peak reduction. The simulation takes place in Austria and up to four vehicles are simulated in a linear optimization with actual tariff conditions. The results show that with intelligent charging no new power peaks are produced and the self-consumption of the existing photovoltaic system is increased. This reduces the load cost in all simulated scenarios. Even with the increased investment cost it comes in each scenario to an improvement. With vehicle to grid charging cost is even further reduced and the existing peaks are reduced. In addition, the photovoltaic self-consumption is further increased. After the investment cost is added, the author comes to the conclusion that only for the case of one vehicle the costs are further reduced. This is the result of the increased investment cost with the vehicle to grid use. It is shown that for an increasing number of electric vehicles, the impact of vehicle to grid is reducing. KW - Vehicle to Grid KW - V2G KW - Kostenoptimierung KW - Elektromobilität KW - Kostenentwicklung Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3151 PB - FH Vorarlberg ER - TY - THES A1 - Hasibeder, Thomas T1 - Low cost Solar Forecast N2 - In der vorliegenden Arbeit wird der Fokus auf die Konzeption eines kostengünstigen Systems zur Vorhersage der solaren Einstrahlung mittels stochastischer Methoden gelegt. Der Vorhersagezeitraum liegt zwischen einer und drei Stunden. Es wird auf die Gefahren der Stochastik und das Aufarbeiten von Daten für stochastische Methoden eingegangen. Bereits die zur Vorhersage verschiedener meteorologischer Daten verwendeten Methoden werden analysiert, angewendet und mittels des relativen Fehlers, dem Root Mean Square Error (Wurzel der mittleren Fehlerquadratsumme) (RMSE) und des Mean Absolute Deviation (MAD) untereinander verglichen. Es werden Kriterien zur Auswahl der zur Aufgabenstellung am besten passenden Methode ausgearbeitet. Die Recherche der vorhandenen stochastischen Methoden und die Anwendung dieser Methoden haben das Artificial Neural Network (künstliches neuronales Netzwerk) (ANN), das mit der Softwarebibliothek Tensorflow erstellt wurde, als die beste Methode hervorgebracht. Die Programmierung der einzelnen Methoden mittels Scikit-learn, Python und Tensorflow wird beschrieben und eine Vorhersage berechnet. Als Hardware wird einerseits ein kostengünstiger Einplatinencomputer, ein Raspberry Pi 3, und andererseits ein leistungsstarkes Notebook verwendet. Die jeweils benötigte Rechenzeit weist keine gravierenden Unterschiede auf. Anschließend wurden die berechneten Vorhersagen mit den vorhandenen Messdaten, der Persistence Method (Persistenz Methode) (PM) und der Vorhersage der Meteo-Schweiz verglichen. Die unterschiedlichen Diagramme der Vorhersagen und deren Genauigkeiten kommen im Verlauf zur Darstellung. Die relative Abweichung der Vorhersage des Artificial Neural Network (künstliches neuronales Netzwerk)(Tensorflow) (ANNT) von den Messdaten liegt über das Jahr 2017 gesehen bei 8.52% oder auf die Jahresenergie bezogen bei 87.3 kWh/m2 . Im Vergleich zur PM Methode weicht die ANNT Methode um 83.5 kWh/m2 und Jahr ab. Abschließend wird auf Verbesserungsmöglichkeiten und weiterführende Arbeiten eingegangen. N2 - This thesis focuses on the development of a cost-effective system to forecast solar radiation by using stochastic methods. The time frame for the forecast lies between one and three hours. The risks of using stochastics and data processing of stochastic methods will be discussed. Various methods for forecasting meteorological data are analyzed, applied and compared by using the relative error, the RMSE or the MAD. A variety of criteria for the selection of a suitable method are formulated. Based on the existing stochastic methods and application of these, it was found that the ANN, which has been created by using the software library Tensorflow, is the best applicable method. The programming of the particular methods, which was done by means of Scikit-learn, Python and Tensorflow, is described and a forecast is produced. As hardware a low cost single-board computer, a Raspberry Pi 3, is used on one hand and on the other hand a high-performance laptop is used. There is no significant difference in the processing time of these two tools. Then the calculated forecasts were compared to the existing measured data, the PM and the forecast of Meteo-Schweiz. The many diagrams of these forecasts and their accuracy are shown in the course of this thesis. In 2017, the relative deviation of the forecast calculated by ANNT from the measured data is at 8.52% or referring to the annual energy, it is 87.3 kWh/m2 . Compared to the PM, the ANNT method deviates by 83.5 kWh/m2 and year. The possibilities for improvements and further research are finally discussed. T2 - Kostengünstige Vorhersage der solaren Einstrahlung KW - Solar Forecast KW - Solar Radiation Prediction KW - Neural Network Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3195 ER - TY - THES A1 - Helppi, Mona T1 - Eine empirische Analyse der organisatorischen Umsetzung von Energiemanagements in Unternehmen und Gemeinden mithilfe von Expertenbefragungen T1 - An empirical analysis of the organizational implementation of energy management in companies and communities with the help of expert surveys N2 - Aktuell beschäftigen steigende Energiepreise, zunehmend knappe Ressourcenvorkommen und der Klimawandel die Energiebranche mehr denn je. Aber auch andere Organisationen wie Unternehmen und Kommunen, die einen erheblichen Beitrag zum Energieverbrauch leisten, sind davon betroffen. Ein Instrument, das sich dieser Themen angenommen hat und eine Möglichkeit zur Steuerung bietet, ist das Energiemanagement. Ungenutztes Energieeffizienzpotential kann mit einem gut aufgebauten und strukturierten Energiemanagement nutzbar gemacht werden. Gerade weil das Angebot technischer Lösungen sehr groß ist, liegt die Vermutung nahe, dass die Umsetzung oft durch strukturelle oder organisationsbedingte Barrieren erschwert wird. Aus diesem Grund ist der Forschungsgegenstand dieser Arbeit eine ausführliche Untersuchung der Umsetzung von betrieblichem und kommunalem Energiemanagement. Es konnten Erkenntnisse gewonnen werden, welche Themen beim Energiemanagement eine Herausforderung darstellen und welche Aspekte spezifisch bei Unternehmen oder Kommunen wichtige Stellschrauben im Umsetzungsprozess sind. Die Ergebnisse der Expertenbefragung und der Literaturanalyse haben gezeigt, dass Energiemanagement derzeit zu wenig Interesse geschenkt wird und deshalb die Investitionen, vor allem in ausreichend Personalressourcen, fehlen. Die größte Hürde ist die wirtschaftliche Darstellbarkeit von Maßnahmen, die insbesondere bei wenig energieintensiven Organisationen Schwierigkeiten bereitet beziehungsweise kaum durchsetzbar ist. Dies wiederum fordert ein Umdenken von Politik und Wirtschaft, was sich auch in anderen Einflussfaktoren deutlich wiederspiegelt. Aber nicht nur in den entscheidenden Reihen einer Organisation muss ein Umdenken stattfinden. Nur wenn das Bewusstsein für Energie bei allen Beteiligten steigt und alle bei Strategie und Umsetzung an einem Strang ziehen, kann die Energiewende mithilfe von Energiemanagement gelingen. N2 - Rising energy prices, increasingly scarce resources and climate change are currently occupying the energy sector more than ever. But other organizations such as companies and municipalities, which make a significant contribution to energy consumption, are also affected. Energy management is an instrument that has addressed these issues and offers an opportunity to control them. Unused energy efficiency potential can be utilized with a well-developed and structured energy management system. Precisely because there is such a wide range of technical solutions on offer, it can be assumed that the implementation is often hampered by structural or organizational barriers. For this reason, the research object of this thesis is a detailed investigation of the implementation of energy management at companies and municipalities. It was possible to gain insights which topics represent a challenge in energy management and which aspects are specifically important for companies or municipalities within the implementation process. The results of the expert survey and the literature analysis have shown that energy management is currently given too little interest and therefore investments are missing, above all in sufficient personnel resources. The biggest hurdle is the economic feasibility of measures that cause difficulties or are hardly enforceable, especially in less energy-intensive organizations. This requires a rethinking of the politics and the economy, which is clearly reflected in other influencing factors. But it is not only in the decisive ranks of an organization that a rethink has to take place. Only if the awareness for energy increases among all participants and everyone pulls together in strategy and implementation the energy revolution can succeed with the help of energy management. KW - Energiemanagement KW - Umsetzung KW - Kommunales Energiemanagement KW - Betriebliches Energiemanagement Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3150 PB - FH Vorarlberg ER - TY - THES A1 - Roller, Fabian T1 - Analyse und Auslegung eines Stromversorgungskonzepts für die Hochschule Ecole Polytechnique d'Abomey-Calavi in Benin T1 - Analysis and design of a power supply concept for the Ecole Polytechnique university d'Abomey-Calavi in Benin N2 - Weltweit hatten 2017 840 Millionen Menschen keinen Zugang zu Strom. Hinzu kommen Millionen weitere Menschen, die an unzuverlässige Stromquellen angeschlossen sind. Für das Wirtschaftswachstum, die menschliche Entwicklung und ökologische Nachhaltigkeit ist eine zuverlässige Stromversorgung jedoch von großer Bedeutung. Die vorliegende Arbeit beschäftigt sich daher mit der Konzeptionierung einer zuverlässigen Stromversorgung für eine Hochschule in Benin (Westafrika), die sich mit einem unzuverlässigen Netzanschluss konfrontiert sieht. Die Konzeptionierung erfolgt mithilfe der Software HOMER. Aufgrund unsicherer Systembedingungen wurden mehrere Szenarien und der Einfluss verschiedener Systemparameter untersucht. Die Ergebnisse zeigen, dass eine zuverlässige Stromversorgung durch die Implementierung eines Mini-Grids erreicht werden kann. Dabei hat die Ausgangssituation einen bedeutenden Einfluss auf die Systemauslegung. Für das untersuchte Szenario, in dem die Hochschule keine Stromkosten bezahlte, erwies sich ein PV/Dieselgenerator/Batterien-Mini-Grid als geeignet. Dabei entstehen Stromkosten von mindestens 0,013 USD pro kWh, was leicht erhöhte Kosten gegenüber den Bezugskosten bedeutet. Dieser Kostenzuwachs lässt sich aber mit der erhöhten Zuverlässigkeit rechtfertigen. Auch unter der Annahme, dass die offiziellen Bezugskosten bezahlt werden müssen, erwies sich ein PV/Dieselgenerator/Batterie-Mini-Grid als geeignet. Die Größe der PV-Anlage fällt in diesem Fall deutlich größer aus, was zu einem reduzierten Einsatz des Dieselgenerators führt. Ein untersuchtes Off-Grid erwies sich als unwirtschaftlich. Somit enthält die Arbeit wichtige Erkenntnisse darüber, wie sich verschiedene Parameter auf ein geeignetes System auswirken. Zudem wurde ein Systemvorschlag ausgearbeitet. Diese Informationen sollen nicht nur den beteiligten Personen vor Ort helfen, sondern auch als Grundlage für zukünftige Projekte dienen. N2 - A reliable electricity supply is of great importance to economic growth, human development, and ecological sustainability. However, in 2017, 840 million people worldwide had no access to electricity, and millions more were connected to unreliable power sources. This paper presents the concept of a reliable power supply for a university in Benin (West Africa), which currently uses an unreliable grid connection. The conception was executed using the software HOMER. Due to uncertain system conditions, several scenarios and the influence of various system parameters were investigated. The results demonstrated that a reliable power supply could be achieved by implementing a mini grid. The initial situation had a significant influence on the system configuration. A PV/diesel generator/batteries mini-grid proved to be suitable for the scenario in which the university does not pay any electricity costs. This configuration resulted in electricity costs of at least US $ 0.013 per kWh, slightly higher than the procurement costs. However, this increase was justified by the increased reliability. When there were official procurement costs, a PV/diesel generator/battery mini-grid was still shown to be suitable. In this scenario, the size of the PV system was significantly larger, which led to reduced use of the diesel generator. An off-grid system was also investigated but proved to be uneconomical. Thus, this work yielded important findings on how different parameters affect a suitable system. In addition, a system proposal was developed. This information should not only help the people involved on-site, but also serve as a basis for future projects. KW - Homer KW - Mini-Grid KW - Stromversorgung KW - Benin KW - Westafrika Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3152 ER - TY - THES A1 - Frick, Helena T1 - Dezentrale Energiegewinnung aus vorsortiertem Müll durch Verbrennung in Benin BT - Einhaltung ökologischer Standards trotz eingeschränkter technischer und finanzieller Möglichkeiten N2 - In Benin werden einerseits große Mengen verschiedenster Abfallarten häufig in der Landschaft entsorgt und unter freiem Himmel verbrannt. Andererseits ist Energie in Benin sehr knapp und muss zu einem hohen Prozentsatz aus Nachbarländern importiert werden. Hier setzt die vorliegende Arbeit an mit der Frage: Welche Varianten der Müllverbrennung mit Nutzung thermischer Energie sind hinsichtlich ökonomischer, technischer und ökologischer Kriterien in Benin realisierbar? Zur Beantwortung dieser Frage werden zunächst die Rahmenbedingungen vor Ort analysiert, um Anforderungen an eine solche Müllverbrennungsanlage abzuleiten. Als Kern der Arbeit wird eine Müllverbrennungsanlage mit anschließender Abgasreinigung konzipiert, die auf einem bereits vor Ort erprobten Ofen aufsetzt, der zur Verbrennung medizinischer Abfälle konstruiert wurde. Anhand einer detaillierten Analyse von Abgasreinigungstechnik wird aufgezeigt, wie dieser Basisofen zur Verbrennung von landwirtschaftlichen Abfällen und Kunststoffen angepasst werden kann. Konkrete Beispiele zur Nutzung thermischer Energie zur Kälteerzeugung, Salzherstellung und Palmölherstellung zeigen auf, dass das vorgestellte Konzept praxistauglich ist. N2 - In Benin, a large amount of waste is disposed in the environment and burned open-field. However, there is a high demand for energy resulting in imports of energy from abroad. This gives rise to the question: what kind of waste incineration with energy extraction can be realized considering economical, technical and environmental aspects in Benin? To answer this question the situation in Benin is analyzed to derive requirements for such a waste incineration plant. The focus of the present work is on the adaption of an incinerator, which has been constructed for incineration of medicinal waste to meet these requirements. Detailed analysis of gas purification techniques is performed and techniques to purify flue gas after incineration of biomass from agricultural waste and plastics are proposed for deployment in Benin. Examples for application of extracted energy like production of cooling, salt and palm oil are given to show the practicability of the concept. KW - Energiegewinnung KW - Müllverbrennung KW - Abgasreinigung KW - Benin Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3146 ER - TY - THES A1 - Kroell, Nikolas T1 - Dynamik der Siliziumkarbid - Bildung in Graphitelektroden durch karbothermale Reduktion in der Gasphase T1 - Dynamics of silicon carbide formation in graphite electrodes through carbothermal reduction in gas phase N2 - Aufgrund des fortschreitenden Klimawandels müssen neue Wege gefunden werden, um diesen zu verlangsamen, bzw. die Emission von Treibhausgasen zu reduzieren. Ein Weg dieses Ziel zu erreichen ist das CO2-Recycling direkt an der Quelle. Durch die hohe thermische und chemische Beanspruchung der hierfür eingesetzten Elektroden bieten sich gerade technische Keramiken als Elektrodenmaterialien an. Eine jener in Frage kommenden Keramiken ist Siliziumkarbid (SiC). Bei SiC handelt es sich um einen Wide-Bandgap-Halbleiter mit hoher thermischer und chemischer Stabilität. Da die Herstellung, des für Elektroden benötigten, hochreinen, porösen SiC sehr aufwendig und damit auch teuer ist, wird schon seit einiger Zeit nach anderen Verfahren, als den industriell eingesetzten Standardverfahren, zur Herstellung von hochreinem SiC geforscht. In der vorliegenden Arbeit wird die Bildung von Siliziumkarbid in isostatisch gepressten Graphiten mittels karbothermischer Reduktion verschieden dotierter Sol-Gel-Granulaten und cerschiedener poröser Graphite untersucht. Zu diesem Zweck werden die Proben unterschiedlichen Anzahlen an Zyklen des in einem Induktionsofen, durchgeführten Hochtemperaturprozesses ausgesetzt. Dabei wird das Granulat thermisch zersetzt, wobei es unter anderem zu einer Gasphasenreaktion mit dem Kohlenstoff der Graphittemplates kommt und damit zur Umwandlung von Kohlenstoff zu SIC. Von den so gewonnenen Proben werden in einem Micro-CT Schichtaufnahmen erstellt. Das Ergebnis soll ein Erkenntnisgewinn bezüglich der Umwandlungstiefe und entstandenen Strukturen in den unterschiedlichen Graphittemplates, je nach Anzahl der durchlaufenen Zyklen und verwendetem Precursorgranulat, sein. Nicht untersucht wird das elektrische Verhalten der unterschiedlichen, auf diese Weise örtlich dotierten, Templates. N2 - Due to the progressing climate change new ways have to be found to decelerate this trend and to reduce the emission of greenhouse gases. One way to achieve this is recycling of the CO2 directly at its source. Because of the high thermal and chemical stress of the used electrodes, ceramics are the materials of choice. A ceramic material, which is suitable for this use is silicon carbide (SiC). SiC is a wide-gap semiconductor with high thermal and chemical stability. The production process of highly pure, porous SiC is very complicated and expensive. Hence, new techniques of producing this material are investigated. In this thesis the formation of SiC in graphite templates, using different sorts of porous graphite and doped sol gel precursors at a carbothermal reduction process is studied. For this purpose, different numbers of cycles of the carbothermal reduction process at an induction furnace are performed on the different graphite templates. In this process the precursor gets pyrolyzed. One result of this pyrolysis is a gas phase reaction of the pyrolysis products with the carbon within the graphite templates converting carbon to SiC. The samples gathered this way are scanned with a micro tomography device. As a result we gain knowledge regarding the depth of conversion and the formed structures inside the different graphite templates, depending on the number of cycles of the high temperature process performed on them and the used doped precursor. The electrical properties of the different templates are not discussed in this thesis. KW - Siliziumkarbid KW - karbothermale Reduktion KW - Silicon Carbide KW - Siliziumkarbid-Bildung Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3154 ER - TY - THES A1 - Diewald, Kevin T1 - Thermodynamische Analyse von Hochtemperaturwärmepumpen unter Verwendung von HFO und HCFO Kältemitteln N2 - Da konventionelle Kältemittel im Vergleich zu CO2 ein großes Treibhauspotential (GWP) aufweisen, gewinnen neue, alternative Kältemittel, sogenannte low-GWP Kältemittel, stärker an Bedeutung. Zu diesen low-GWP Kältemitteln gehören u.a. die Fluide der HFO und HCFO Kältemittel. Durch ihre thermophysikalischen Eigenschaften eignen sie sich insbesondere für die Anwendung in industriellen Hochtemperaturwärmepumpen (HTWP), die im Temperaturbereich von 100 °C bis 160 °C ein großes Potenzial in der Nahrungsmittel-, Papier- und Chemieindustrie zur Prozesswärmebereitstellung aufweisen. In dieser Masterarbeit werden die Kältemittel R1336mzz(Z), R1233zd(E), R1224yd(Z), R1234ze(Z) und R514A auf ihre Anwendbarkeit in drei verschiedenen Kältekreiskonfigurationen untersucht. Dabei soll herausgefunden werden, welches Kältemittel sich unter Berücksichtigung des COPs, der volumetrischen Heizleistung, der Verdichtungsverhältnisse und Verdichtungsendtemperaturen am besten eignet. Der Kreislauf mit internem Wärmeübertrager (IHX) findet bereits Anwendung in HTWP und dient zum grundlegenden Vergleich der Kältemittel. Die beiden neuen Kreisläufe eignen sich u.a. für große Spreizungen an der Senke. Eine in dieser Arbeit betrachteten Kältekreiskonfiguration besteht aus zwei parallel angeordneten IHX Kreisläufen (2KP) und die andere aus einer zweistufigen Kreislaufkonfiguration (2SE). Mithilfe des Programms EES wird für die Kreisläufe ein Modell erstellt, mithilfe dessen der Senkentemperaturbereich von 100 °C bis 160 °C und der Quellentemperaturbereich von 40 °C bis 80 °C untersucht werden kann. Die Auswertung der Simulationen kam zu dem Ergebnis, dass R514A bis zu einer Senkentemperatur von 130 °C und R1336mzz(Z) ab dieser Senkentemperaturen im IHX und 2SE Kreislauf die besten COP Werte aufweist. Zudem sind die Verdichtungsendtemperaturen und das Verdichtungsverhältnis günstig, die volumetrische Heizleistung hingegen am geringsten. Im 2KP Kreislauf besitzt die Kältemittelkombination R1336mzz(Z)/R514A die besten COP Werte. Der 2KP Kreislauf weist die besten COP Werte der betrachteten Kältekreiskonfigurationen auf. Im Betriebspunkt bei einer Senkentemperatur von 130 °C (ΔT Senke 60 K) und einer Quellentemperatur von 60 °C (ΔT Quelle 10 K) liegt der COP des IHX bei 3,95, der des 2SE bei 4,05 und der des 2KP bei 4,26. R1233zd(E) überzeugt im IHX und 2SE Kreislauf mit einer deutlich höheren VHC im Vergleich zu R1336mzz(Z), bei etwas geringeren COP Werten. Die Untersuchung zeigt auch, dass die Auswahl einer Kältekreiskonfiguration und eines Kältemittels stark von den Betriebstemperaturen abhängt. N2 - Since conventional refrigerants have a large global warming potential (GWP) compared to CO2, new, alternative refrigerants, so-called low-GWP refrigerants, are gaining in importance. These low-GWP refrigerants include the fluids of HFO and HCFO refrigerants. Due to their thermophysical properties, they are particularly suitable for use in industrial high-temperature heat pumps, which have great potential for supplying process heat in the food, paper and chemical industries in the temperature range from 100 °C to 160 °C. This master thesis examines the refrigerants R1336mzz(Z), R1233zd(E), R1224yd(Z), R1234ze(Z) and R514A for their applicability in three different refrigerant circuit configurations. The aim is to find out which refrigerant is best suited considering the COP, volumetric heating capacity, compression ratios and final compression temperatures. The circuit with an internal heat exchanger (IHX) is already used in high temperature heat pumps up to sink temperatures of 130 °C and is used for the basic comparison of refrigerants. The two new circuits are suitable, for example, for large temperature differences at the sink. One circuit consists of two parallel IHX circuits (2KP) and the other one of a two-stage circuit configuration (2SE). The EES program is used to create a model of the circuits that can be used to study the sink temperature range from 100 °C to 160 °C and the source temperature range from 40 °C to 80 °C. The evaluation of the simulations concluded that R514A had the best COP values in the IHX and 2SE circuit up to sink temperatures of 130°C. For a sink temperature of 130 °C and higher R1336mzz(Z) has the best COP values in these circuits. In addition, the discharge temperatures and the compression ratio are favorable, while the volumetric heating capacity is the lowest. In the 2KP circuit, the refrigerant combination R1336mzz(Z)/R514A has the best COP values. The 2KP circuit has the best COP values of the considered refrigerant circuit configurations. At the operating point at a sink temperature of 130 °C (ΔT sink 60 K) and a source temperature of 60 °C (ΔT source 10 K), the COP value of the IHX is 3.95, the 2SE is 4.05 and the 2KP is 4.26. R1233zd(E) convinces in the IHX and 2SE circuit with a significantly higher VHC compared to R1336mzz(Z) at slightly lower COP values. The investigation also shows that the selection of a refrigerant circuit configuration and a refrigerant depends strongly on the operating temperatures. KW - Hochtemperaturwärmepumpen KW - HFO KW - HCFO KW - Kältemittel Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3145 PB - FH Vorarlberg ER - TY - THES A1 - Haag, Hermann T1 - Dc biased equivalent series resistance measurement and loss estimation in ferro electric ceramic capacitors N2 - In this thesis the effect of dc voltage bias on the equivalent series resistance (ESR) of capacitors and especially ferroelectric dielectric ceramic capacitors (FDCC) is analysed. Further the influence of the dc biased ESR on the losses of capacitors is investigated. Also piezoelectric resonances (PR) occurring in FDCCs with applied dc bias and their influence on the losses are analysed. Therefore a measurement circuit to measure the impedance and thus the ESR of capacitors in combination with a vector network analyser (VNA) is developed. Using the developed circuit the ESR of capacitors of different technologies is measured and their behaviour with dc bias is evaluated. The losses of an FDCC are measured in a power electronic (PE) circuit with a developed calorimetric measurement system (CMS). The influence of the PR is investigated by tuning the switching frequency of the PE system and thus the frequency of the capacitor current exactly into the PR. The measured losses are then compared to a calculation based on the capacitor current harmonics and the respective ESR. The measurements show an increase of the ESR with dc bias for all measured FDCCs. The loss measurements show a significant increase of the losses in an FDCC if the current frequency matches the PR frequency. Consequently a decrease of the PE system's efficiency is measured. The loss calculations do not exactly match the measurements but there is a systematic deviation of the same order for all measurements. N2 - In dieser Arbeit wird der Effekt von Gleichspannung auf den äquivalenten Serienwiderstand (ESR) von Kondensatoren und im speziellen von ferroelektrischen Keramikkondensatoren (FDCC) untersucht. Weiters wird der Einfluss des ESR unter Gleichspannung auf die Verluste in den Kondensatoren untersucht. Piezoelektrische Resonanzen (PR) welche in FDCCs mit anliegender Gleichspannung auftreten werden analysiert und deren Einfluss auf die Verluste inspiziert. Für diese Untersuchungen wird eine Messschaltung entwickelt um die Impedanz bwz. den ESR von Kondensatoren in Kombination mit einem vektoriellen Netzwerkanalysator mit anliegender Gleichspannung zu messen. Die Schaltung wird verwendet um den ESR von Kondensatoren unterschiedlicher Technologie zu messen und deren Verhalten in Bezug auf Gleichspannung zu evaluieren. Die Verluste eines FDCCs werden in einer leistungselektronischen Schaltung mit einem kalorimetrischen Messsystem gemessen. Der Einfluss der PR auf die Verluste wird gemessen indem die Schaltfrequenz der leistungselektronischen Schaltung genau der PR Frequenz entsprechend eingestellt wird. Somit entspricht auch die Frequenz des Kondensatorstromes der Frequenz der PR. Die gemessenen Verluste werden mit einer Berechnung verglichen, die die Fourier Koffzienten des Stromes, sowie den entsprechenden ESR verwendet. Die Messungen zeigen einen zunehmenden ESR mit Gleichspannung für die gemessenen FDCCs. Die Verlustmessungen zeigen eine signifikante Zunahme der Verluste in einem FDCC wenn der Strom genau einer PR entspricht. Folglich ist auch eine Abnahme des Gesamtwirkungsgrades der Schaltung an diesem Punkt zu beobachten. Die Verlustberechnungen stimmen nicht exakt mit den Messungen überein, aber die Abweichungen liegen für alle Messungen in der gleichen Größenordung und Richtung. T2 - Messung des äquivalenten Serienwiderstandes und Verlustbestimmung von ferroelektrischen Keramikkondensatoren unter anliegender Gleichspannung KW - Dc Bias KW - ESR KW - Ceramic Capacitor KW - Ferroelectric KW - Piezoelectric Effect Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3148 ER - TY - THES A1 - Saliari, Till T1 - Bewertung und Entwicklung von Konzepten zur verbraucherseitigen Regelung im Niederspannungsnetz von nichtöffentlichen Ladestationen für Elektroautos T1 - Evaluation and development of concepts for consumer-side control of non-public charging stations for electric cars in the low-voltage grid N2 - Heimische Ladevorgänge von Elektroautos sind ein zusätzlicher Faktor in dem Wandel, dem Verteilnetze ausgesetzt sind. Aufgrund der typischen langen Parkzeiten bietet das Laden von Elektroautos jedoch einen hohen Grad an Flexibilität, mit deren Hilfe die Netzbelastung entscheidend verringert werden kann und weitere Dienstleistungen, auch in höheren Netzebenen, erbracht werden können. Die vorliegende Arbeit bewertet mit dem Instrument der Nutzwertanalyse fünf Ladestrategien, wie die Koordinierung von Ladevorgängen nutzbringend eingesetzt werden kann. Dazu werden im ersten Schritt Kriterien auf Basis der Literaturrecherche sowie der gegebenen Informationsgrundlagen der betrachteten Systeme definiert. Um eine neutralere Bewertung zu ermöglichen, wird die Gewichtung der Kriterien zusätzlich von einem Vertreter eines Verteilernetzbetreibers und einem Energieversorger vorgenommen. Mit den Ergebnissen der Bewertung werden die Systeme hinsichtlich ihres Nutzens unter Berücksichtigung der Bedeutung für die jeweiligen Parteien verglichen. Dabei werden die Stärken und Schwächen der Systeme herausgestellt und mögliche Interessenskonflikte lokalisiert. Ebenfalls wird auf die Eignung der Nutzwertanalyse als Werkzeug zur Bewertung der Systemkonzepte eingegangen. Im Anschluss wird der Grundaufbau eines Systems vorgestellt, welches aufgedecktes Potential zur Weiterentwicklung der bewerteten Systeme nutzt und damit zu einem größeren Gesamtnutzen führen kann. N2 - Domestic charging of electric cars is an additional factor in the change that low voltage networks are exposed to. However, due to the typical long parking times, the charging of electric cars offers a high degree of flexibility, which can significantly reduce grid load and provide additional services, even at higher network levels. The present work uses the cost-benefit analysis as a tool to evaluate five charging strategies on how charging coordination can be usefully employed. For this purpose, criteria are defined in the first step on the basis of the literature search as well as the given information basis of the considered systems. In order to allow a more neutral assessment, the weighting of the criteria is additionally carried out by a representative of a distribution system operator and an energy supplier. The results of the evaluation are used to compare the systems in terms of their value, taking into account their importance to the respective parties. The strengths and weaknesses of the systems are highlighted and potential conflicts of interest are pinpointed. The suitability of the utility value analysis as a tool for evaluating the system concepts is also discussed. Subsequently, the basic structure of a system is presented, which utilizes the discovered potential for the further development of the evaluated systems and thus can lead to a greater overall benefit. KW - E-Mobilität KW - Ladestationen - Regelung KW - Smart Grid KW - Demand Management Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3198 ER - TY - THES A1 - Rauschenbach, Laura T1 - Potentialstudie thermischer Lastverschiebung in großvolumigen Wohngebäuden unter Einsatz von Wärmepumpe, Solarthermie und Photovoltaik T1 - Potential study of thermal load transfer in spacious residential buildings using thermal heat pump, solar thermal power and photovoltaics N2 - Die Gebäudeenergieversorgung mittels kombinierter Erneuerbarer Energiesysteme wird in Zukunft häufiger realisiert werden. Dies liegt unter anderem am Fokus der aktuellen Energiepolitik, an der wachsenden Akzeptanz der Bevölkerung und an einer ständigen Verbesserung der Wohngebäudeeigenschaften. Die volatile Charakteristik des erneuerbaren Energieangebots stellt eine Herausforderung dar. Thermische Lastverschiebung ermöglicht es, durch die Speicherung thermischer Energie, Zeiten mit geringem Energieertrag zu überbrücken. Es werden in dieser Masterarbeit drei Methoden zur Lastverschiebung mittels Simulation einer Referenzwohnanlage mit 31 Wohnungen untersucht. Die Gebäudesimulation wird hierfür mit TRNSYS durchgeführt, die Simulation zum Vergleich der unterschiedlichen Methoden mit Polysun. Die untersuchten Methoden sind die Regeneration des Erdsondenfeldes einer Geothermiewärmepumpe, die Anhebung der Maximaltemperatur sensibler Wärmespeicher, sowie die Anhebung der Raumtemperatur in der Referenzwohnanlage. Die Ergebnisse zeigen, dass die Sondenregeneration eine effektive Methode zur Steigerung der Jahresarbeitszahl (JAZ) der Wärmepumpe und des solaren Deckungsbeitrags darstellt. Die Sondentemperatur kann im Referenzfall zeitweise sogar auf ein höheres Niveau angehoben werden. Durch die zusätzliche Kombination mit einer Erhöhung der Speichermaximaltemperatur, bei hohem solarthermischem Ertrag, kann eine weitere Steigerung der JAZ erreicht werden. Die Solarthermieanlage kann so den größten Temperaturbereich nutzen, was auch die solare Deckungsrate weiter anhebt. Die thermische Gebäudeaktivierung weist das größte Potential für die Steigerung des PV-Eigenverbrauchs auf und verbessert die JAZ der Wärmepumpe durch den vermehrten Betrieb im Niedertemperaturbereich bedeutend; Jedoch wächst der Heizwärmebedarf (HWB) für die untersuchte Referenzwohnanlage aufgrund der Raumtemperaturüberhöhung (RTÜ) dermaßen, dass sie den Benefit der zusätzlich genutzten erneuerbaren Energie übersteigt und diese Methode zur thermischen Lastverschiebung daher nicht empfehlenswert ist. Da die thermische Gebäudeaktivierung in dieser Studie für bestimmte Gebäudeeigenschaften und mittels Fußbodenheizung realisiert ist, wird darauf hingewiesen, dass die Ergebnisse nur bedingt übertragbar sind und bei veränderten Gebäudeeigenschaften stark abweichen können. N2 - In the future realizing the energy supply of buildings, using renewable energy systems will increase. A reason for this incline can be found in the steady improvement of building technology, such as the decrease of the energy demand by improving insulation standards or using more effective energy supply systems. The volatile characteristics of energy generation is a major challenge when using renewable energies. By thermal load transfer the thermal energy can be stored in times of low supply from renewable energy systems up to a certain extend. In this study three different methods of thermal load transfer are being evaluated. The building simulation is implemented in TRNSYS, while the simulation of control strategies is realized in Polysun. The examined methods are firstly the regeneration of the geothermal probe of a geothermal heat pump, secondly raising the maximum temperature in the heat storage tanks and lastly increasing the room temperature of the reference residential buildings, as well a combination of all three stated methods. The results show that the probe regeneration effectively increases the annual performance factor of the heat pump and the solar thermal coverage of energy needs. In the reference case the probe temperature can even be increased temporarily to a higher level. An additional increase of the annual performance factor can be achieved by combining the probe regeneration and raising the maximum storage temperature in times of high renewable energy yield. Here, the solar thermal plant can use an enlarged range of temperature, which also increases the coverage rate further and is therefore recommended for the reference system. The raising of the room temperature has the most potential for the increase of the photovoltaic self-consumption rate and improves the annual performance factor of the heat pump through the expanded use in the low temperature range significantly. However, the load transfer increases the demand for heat in the examined reference residential building so much, that it exceeds the benefit of the renewable energy which additionally have been made usable. Therefore, this method is not recommended in that case. As the thermal building activation is here only realized for certain building features and only via underfloor heating, it must be noticed, that the results are only partly transferable, as they differ with different building features. Therefore, it is recommended, that this method is simulated and evaluated separately for each different use case. KW - Thermische Lastverschiebung KW - Transys KW - Polysun KW - Gebäudesimulation Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3197 ER - TY - THES A1 - Egger, Felix T1 - Synthese von Gashydraten T1 - Synthesis of gas hydrates BT - Entwicklung eines multifunktionalen Versuchsreaktors N2 - Bei Clathraten handelt es sich um Einschlussverbindungen, bei denen beliebige Gastmoleküle in einem Käfig bzw. Gitter von beliebigen Wirtsmolekülen eingeschlossen sind. Bei hohem Druck und niedriger Temperatur können beispielsweise Gasmoleküle in einem Wirtsgitter aus Wassermolekülen eingelagert werden. Natürlich vorkommende Hydrate in den Tiefeneisfeldern der Schelfmeere und in Permafrostgebieten zu finden und haben hauptsächlich Methan als Gastgas. Im Forschungsbereich Energie der Fachhochschule Vorarlberg (FHV) werden die Bildungs- und Zerfallsprozesse von Gashydraten erforscht. Für die Herstellung dieser Proben ist ein Mikroreaktor vorhanden, mit dem keine zufriedenstellenden Ergebnisse erzielt werden können, da die Dauer der Bildung von ausreichenden Mengen an Hydratproben hoch ist. Obwohl die Synthese von Hydraten bereits mehrfach Gegenstand der Forschung war und es weiterhin ist, besteht nach wie vor ein großes Potential in der Beschleunigung des Wachstumsprozesses von Hydraten. Da der Beginn des Hydratwachstums durch einen stochastischen Prozess ausgelöst wird, kann die Dauer der Keimbildung bzw. bis zum Beginn des Kristallwachstums viel Zeit in Anspruch nehmen. Für weitere Forschungsarbeiten im Forschungsbereich Energie der FHV ist eine beschleunigte und technisch einfache Herstellung von Hydraten von hoher Wichtigkeit. Deshalb ist der Fokus bzw. das Thema dieser Arbeit die Entwicklung eines neuartigen Versuchsreaktors, der die Möglichkeit bietet, verschiedene bekannte sowie neue Methoden für die Synthese von Gashydrat anzuwenden und für die Herstellung von Hydratproben untereinander zu kombinieren. Der im Zuge dieser Arbeit entwickelte Versuchsreaktor ist so aufgebaut, dass mehrere aus der Literatur bekannte Synthesemethoden, sowohl einzeln wie auch in Kombination untereinander, verwendet werden können. Als zusätzliche und neuartige Synthesemethode ist eine Baugruppe des Aufbaus darauf ausgelegt, das Hydratwachstum ausschließlich aus der Gasphase zu ermöglichen. Der Versuchsaufbau verfügt über mehrere Temperaturfühler und einen Druckaufnehmer, die über ein Datenerfassungssystem eine Steuerung und eine Überwachung des Herstellungsprozesses erlauben. Es wurden neben verschiedenen Inbetriebnahmetests insgesamt drei Versuche zur Ermittlung der Tauglichkeit des Systems zur Hydratsynthese durchgeführt. In jeder dieser drei Versuchsreihen konnten neue Erkenntnisse bezüglich des Wachstumsprozesses von Hydraten gewonnen werden, die auch in der gesichteten Literatur bisher nicht dokumentiert sind. Weiters wurde die neuartige Synthesemethode aus der Gasphase erprobt. Obwohl diese grundsätzlich funktioniert, sind die erreichbaren Produktionsraten prozessbedingt niedrig. Das Ziel, Hydratproben einfach und schnell erzeugen zu können, konnte mit dem entwickelten Versuchsreaktor erreicht werden. N2 - Clathrates are inclusion compounds in which variable gas molecules are inclosed in a cage or grill of variable host molecules. With high pressure and low temperature, it is possible to place into stock for example gas molecules in a host grill composed of water molecules. Hydrates occur naturally for instance in the deep ice fields of the shelf sea and in permafrost zones and mainly have methane as a host gas. In the research institute for energy of the Fachhochschule Vorarlberg (FHV) they investigate the formation and decay processes of gas hydrates. For the production of these samples, there is a micro reactor, which is not appropriate to provide satisfactory results because the formation of sufficient quantities of gas hydrates takes a very long time. Although until now it has been done a lot of research on the synthesis of hydrates, there is still the need to accelerate the growth process of hydrates. As the beginning of this process is initiated by a stochastic process, the nucleation and respectively the beginning of the crystal growth may take a lot of time. In order to facilitate more research and investigations on the research institute for energy of the FHV it is essential to provide a faster and technically easier hydrate production. Because of this the main issue of the present thesis is the development of a new and innovative experimental reactor which renders possible to use many different new or well-known methods for the synthesis of gas hydrates and to combine these also for the fabrication of hydrate samples. The experimental reactor, which was developed in the course of the present thesis, was constructed like that in order to allow the use of several synthesizing methods separately and in combination with the others. As an additional and innovative synthesizing method, a component of the structure aims at rendering possible the hydrate growth during the gas phase. There are several temperature sensors and a pressure transducer, which allow to control and to supervise the production process via a data acquisition system. In addition to different commissioning tests there were carried out three tests in order to check the efficiency of the hydrate synthesizing system. In each of the conducted experiments there could be gained new results about the growth process of hydrates, which have not appeared until then in the common literature. Moreover, the innovative synthesizing method with the gas phase was tested. Although this method generally works, the reachable production rates are very low due to the process. The aim to produce hydrate samples easily and quickly could be reached with the developed experimental reactor. KW - Hydrate KW - Clathrat KW - Methan KW - Reaktor KW - Rührwerk Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3193 ER - TY - CHAP A1 - Plankensteiner, Kathrin ED - Werth, Wolfgang T1 - Zuverlässigkeitsanalyse von Schweißprozessen mit Supervised Learning Methoden BT - "Machine Learning und Data Science in der Mechatronik". Tagungsband. Villach, 21. November 2019. FH Kärnten, Campus Villach T2 - Konferenz der Mechatronik Plattform Österreich 2019 N2 - In dieser Arbeit wird Supervised Learning verwendet, um die Zuverlässigkeit von Schweißverbindungen zu evaluieren. Um die Schweißqualität zu bestimmen, wurden End of Life Tests durchgeführt. Für die statistische Auswertung und Vorhersage der zu erwartenden Lebensdauer, wurden die Daten basierend auf einer logarithmischen Normalverteilung und mit einer multivariablen linearen Regression modelliert. Um die signifikanten Einflussfaktoren zu identifizieren, wurde eine schrittweise Regression genutzt. Die Ergebnisse zeigen, dass das entwickelte Modell die Zuverlässigkeit und Lebensdauer der Schweißverbindung akkurat abbildet und präzise Vorhersagen liefern kann. KW - Zuverlässigkeitsanalyse KW - Lebensdauermodellierung KW - Regressionsanalyse KW - Machine Learning Y1 - 2019 U6 - http://dx.doi.org/10.25924/opus-3176 SP - 30 EP - 31 PB - FH Kärnten CY - Villach ER - TY - JOUR A1 - Kostal, Elisabeth A1 - Stroj, Sandra A1 - Kasemann, Stephan A1 - Matylitsky, Victor A1 - Domke, Matthias T1 - Fabrication of biomimetic fog-collecting superhydrophilic–superhydrophobic surface micropatterns using femtosecond lasers JF - Langmuir Y1 - 2018 U6 - http://dx.doi.org/10.1021/acs.langmuir.7b03699 SN - 0743-7463 VL - 34. Jg IS - H. 9 SP - 2933 EP - 2941 ER - TY - JOUR A1 - Huber, Daniel A1 - Reindl, Marcus A1 - Covre da Silva, Saimon Filipe, A1 - Schimpf, Christian A1 - Martin-Sanchez, Javier A1 - Huang, Huiying A1 - Piredda, Giovanni A1 - Edlinger, Johannes A1 - Rastelli, Armando A1 - Trotta, Rinaldo T1 - Strain-tunable GaAs quantum dot: a nearly dephasing-free source of entangled photon pairs on demand JF - Physical Review Letters Y1 - 2018 U6 - http://dx.doi.org/10.1103/PhysRevLett.121.033902 VL - o.Jg IS - Bd. 121, H. 3/033902 ER - TY - JOUR A1 - Sagmeister, Martin A1 - Koppitsch, Günther A1 - Muellner, Paul A1 - Nevlacsil, Stefan A1 - MaeseNovo, Alejandro A1 - Hainberger, Rainer A1 - Seyringer, Dana A1 - Kraft, Jochen T1 - Monolithically integrated, CMOS-compatible SiN photonics for sensing applications JF - Proceedings KW - AWG KW - OCT KW - optical waveguides KW - photonics KW - Si3N4 waveguides Y1 - 2018 U6 - http://dx.doi.org/10.3390/proceedings2131023 VL - 2. Jg IS - H. 13: Eurosensors 2018. Graz, Austria. 9-12 September 2018 ER - TY - JOUR A1 - Moser, Regina A1 - Domke, Matthias A1 - Winter, Jan A1 - Huber, Heinz A1 - Marowsky, Gerd T1 - Single pulse femtosecond laser ablation of silicon – a comparison between experimental and simulated two-dimensional ablation profiles JF - Advanced Optical Technologies KW - femtosecond laser ablation KW - silicon laser ablation KW - two-dimensional morphology KW - two-temperature model Y1 - 2018 U6 - http://dx.doi.org/10.1515/aot-2018-0013 SN - 2192-8576 VL - 7. Jg IS - H. 4 SP - 255 EP - 264 ER - TY - JOUR A1 - Matylitskaya, Volha A1 - Kasemann, Stephan A1 - Urban, Gerald A1 - Dincer, Can A1 - Partel, Stefan T1 - Electrochemical characterization of nanogap interdigitated electrode arrays for lab-on-a-chip applications JF - Journal of The Electrochemical Society KW - Biosensor KW - Chronoamperometry KW - Electrochemical detection KW - IDA KW - Interdigitated electrode array KW - Lab-on-a-Chip KW - Nanogap KW - oa Y1 - 2018 U6 - http://dx.doi.org/10.1149/2.0701803jes SN - 0013-4651 VL - 165. Jg IS - H. 3 ER - TY - JOUR A1 - Domke, Matthias A1 - Wick, Sebastian A1 - Laible, Maike A1 - Rapp, Stephan A1 - Huber, Heinz A1 - Sroka, Ronald T1 - Ultrafast dynamics of hard tissue ablation using femtosecond-lasers JF - Journal of Biophotonics KW - ablation KW - elastic constants KW - femtosecond-laser KW - hard tissue KW - microscopy KW - pump-probe KW - ultrafast laser KW - ultrashort pulse laser Y1 - 2018 U6 - http://dx.doi.org/10.1002/jbio.201700373 SN - 1864-0648 VL - 11. Jg IS - H. 10/e201700373 ER - TY - JOUR A1 - Kostal, Elisabeth A1 - Kasemann, Stephan A1 - Dincer, Can A1 - Partel, Stefan A1 - Köck, Anton A1 - Deluca, Marco T1 - Impedimetric characterization of interdigitated electrode arrays for biosensor applications JF - Proceedings Y1 - 2018 U6 - http://dx.doi.org/10.3390/proceedings2130899 VL - 2. Jg IS - H. 13: Eurosensors 2018. Graz, Austria. 9-12 September 2018/899 ER - TY - JOUR A1 - Boudoire, Florent A1 - Partel, Stefan A1 - Toth, Rita A1 - Heier, Jakob T1 - Combining parallel pattern generation of electrohydrodynamic lithography with serial addressing JF - RSC Advances Y1 - 2018 U6 - http://dx.doi.org/10.1039/C8RA06160B SN - 2046-2069 VL - 8. Jg IS - H. 54 SP - 30932 EP - 30936 ER - TY - CHAP A1 - Chovan, Jozef A1 - Uherek, Frantisek A1 - Figura, Daniel A1 - Seyringer, Dana A1 - Gajdosova, Lenka ED - Nevrela, Juraj ED - Micjan, Michal ED - Novota, Miroslav ED - Kovac, Jaroslav T1 - Design and simulation of Si/SiO2/SiN waveguides structure T2 - Proceedings of ADEPT. 6th International Conference on Advances in Electronic and Photonic Technologies. Tatranska Lomnica, High Tatras, Slovakia. June 18 - 21, 2018 Y1 - 2018 SP - 160 EP - 163 PB - Institute of Electriconics and Photonics, FEI STU CY - Bratislava ER - TY - CHAP A1 - Kempter, Guido A1 - Werner, Tobias A1 - Ritter, Walter ED - Jost, Patrick ED - Kempter, Guido T1 - Verhaltensreaktionen auf die Wahrnehmung menschlich agierender Industrieroboter in einer Übergabesituation T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 159 EP - 166 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Jost, Patrick A1 - Werner, Tobias A1 - Dillinger, Markus ED - Jost, Patrick ED - Kempter, Guido T1 - User experience of static and dynamic augmented reality in a cleanroom work scenario T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 102 EP - 110 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Werner, Tobias A1 - Dorn, Sonia A1 - Carrasco, Javier ED - Jost, Patrick ED - Kempter, Guido T1 - Automatisierung eines Prüfarbeitsplatzes mittels Industrieroboter T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 121 EP - 126 PB - Pabst Science Publishers CY - Lengerich ER - TY - JOUR A1 - Werner, Tobias A1 - Carrasco, Javier T1 - Validating autofocus algorithms with automated tests JF - Robotics Y1 - 2018 U6 - http://dx.doi.org/10.3390/robotics7030033 VL - 7. Jg IS - H. 3/33 ER - TY - CHAP A1 - Künz, Andreas A1 - Trommelschläger, Karin A1 - Kempter, Guido A1 - Hohpe, Sarah A1 - Jost, Patrick A1 - Dontschewa, Miglena ED - Jost, Patrick ED - Kempter, Guido T1 - Prozessführung mittels Spatial Augmented Reality T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 127 EP - 134 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Burtscher, Catalina A1 - Gaso, Peter A1 - Pudis, Dusan ED - Nevrela, Juraj ED - Micjan, Michal ED - Novota, Miroslav ED - Kovac, Jaroslav T1 - Design of polymer waveguides for photonic components T2 - Proceedings of ADEPT. 6th International Conference on Advances in Electronic and Photonic Technologies. Tatranska Lomnica, High Tatras, Slovakia. June 18 - 21, 2018 Y1 - 2018 SP - 57 EP - 60 PB - Institute of Electriconics and Photonics, FEI STU CY - Bratislava ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Manahl, Werner ED - Naweed, Anjum ED - Wardaszko, Marcin ED - Leigh, Elyssebeth ED - Meijer, Sebastiaan T1 - Gaming simulation as a science of design approach T2 - Intersections in simulation and gaming. 21st Annual Simulation and Gaming Association Conference, ISAGA 2016 held as part of the first Australasian Simulation Congress, ASC 2016. Melbourne, VIC, Australia, September 26-29, 2016, revised selected papers T2 - LNCS, 10711 Y1 - 2018 SN - 978-3-319-78794-7 SN - 978-3-319-78795-4 U6 - http://dx.doi.org/10.1007/978-3-319-78795-4_27 SP - 380 EP - 393 PB - Springer CY - Cham ER - TY - CHAP A1 - Poulain, Benjamin A1 - Plankensteiner, Kathrin A1 - Rigger, Eugen A1 - Schöch, Robert A1 - Merz, Robert ED - Bleicher, Friedrich T1 - Concept of probabilistic modeling for real-time prediction of product quality and design automation T2 - Efficiency, Flexibility, Integration. Wiener Produktionstechnik Kongress 2018. WPK 2018, 26.-27.9.2018 Y1 - 2018 SP - 205 EP - 214 PB - New academic press CY - Wien ER - TY - CHAP A1 - Burtscher, Catalina A1 - Lucki, Michal A1 - Seyringer, Dana ED - Jaworski, Marek ED - Marciniak, Marian T1 - Waveguide shape modelling and optimization for high channel Y-branch splitter in optical transmission systems T2 - ICTON 2018. 20th Anniversary International Conference on Transparent Optical Networks. 1-5 July 2018, Bucharest, Romania KW - access network KW - background noise KW - DWDM KW - FTTx networks KW - GPON access networks KW - high channel Y-branch splitter KW - insertion loss KW - integrated optics KW - light transmission KW - Noise measurement KW - optical beam splitters KW - optical communication equipment KW - optical fibre losses KW - optical fibre networks KW - optical noise KW - optical splitting KW - optical transmission systems KW - optical waveguides KW - passive optical networks KW - PON KW - Shape KW - splitting properties KW - Standards KW - telecommunication KW - XG-PON access networks KW - Y-branch splitter KW - Y-branch waveguide shape modelling Y1 - 2018 U6 - http://dx.doi.org/10.1109/ICTON.2018.8473871 PB - National Institute of Telecommunications CY - Warsaw ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Stamatov, Denise A1 - Künz, Andreas A1 - Marinov, Marin A1 - Cagin, Emine A1 - Bernard, André A1 - Edlinger, Johannes ED - Jost, Patrick ED - Kempter, Guido T1 - Virtuelle Erkundungen von Arbeitsumgebungen im Reinraum T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 189 EP - 196 PB - Pabst Science Publishers CY - Lengerich ER - TY - JOUR A1 - Akolkar, Anupam A1 - Petrasch, Jörg A1 - Finck, Steffen A1 - Rahmatian, Nima T1 - Combined experimental-numerical identification of radiative transfer coefficients in white LED phosphor layers JF - Optical Materials KW - Inverse problem KW - Light-emitting diodes KW - Monte Carlo Ray Tracing KW - Phosphor layer Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.optmat.2017.12.040 SN - 0925-3467 VL - o.Jg. IS - Bd. 76 SP - 278 EP - 286 ER - TY - CHAP A1 - Böhler, Doris ED - Brown, Mabel Ann T1 - Supporting vulnerable youth - Austria’s active policiy of education and work integration with young people at risk T2 - The shifting global world of youth and education KW - +SEC 391 EIN KW - Einwanderer, Ausländer : Bildung Y1 - 2018 SN - 978-1-138-21074-5 SP - 149 EP - 160 PB - Routledge Taylor & Francis Group CY - London ET - First published ER - TY - CHAP A1 - Böhler, Doris ED - Pfaller-Rott, Monika ED - Gomez-Hernandez, Esperanza ED - Soundari, Hilaria T1 - Approaching the refugee situation in Austria from a diversity perspective - values, public discourse and social work strategies T2 - Soziale Vielfalt. Internationale Soziale Arbeit aus interkultureller und dekolonialer Perspektive Y1 - 2018 SP - 139 EP - 147 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Duden, Antje A1 - McCormick Williams, Michael ED - Duden, Antje T1 - Analoge und digitale Kommunikation T2 - Zusammenarbeit analog und digital Y1 - 2018 SN - 978-3-96138-109-8 SP - 1 EP - 13 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Stamatov, Denise A1 - Künz, Andreas A1 - Marinov, Marin T1 - Virtual exploration of working environments T2 - 9th National Conference with International Participation. ELECTRONICA 2018. Proceedings. May 17-18, 2018. National Science and Technical Centre. 108 Rakovski St, 1000 Sofia, Bulgaria KW - 3D modeling KW - artificial KW - augmented KW - Browsers KW - Cameras KW - Gears KW - head mounted displays KW - helmet mounted displays KW - HTC-VIVE KW - interactive variations KW - Internet KW - mobile computing KW - mobile presentations KW - scene analysis KW - Three-dimensional displays KW - Tools KW - Training KW - virtual exploration KW - virtual realities KW - virtual reality KW - virtual reality study KW - VR sets KW - VR-Goggles KW - working environments KW - workrooms Y1 - 2018 SN - 978-1-5386-5801-7 U6 - http://dx.doi.org/10.1109/ELECTRONICA.2018.8439403 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Akolkar, Anupam A1 - Rahmatian, Nima A1 - Unterberger, Seraphin A1 - Petrasch, Jörg T1 - Modeling the effect of infrared opacifiers on coupled conduction-radiation heat transfer in expanded polystyrene JF - Journal of Heat Transfer Y1 - 2018 U6 - http://dx.doi.org/10.1115/1.4040784 SN - 0022-1481 VL - o.Jg IS - Bd. 140, H. 11/112005 ER - TY - JOUR A1 - Kepplinger, Peter A1 - Huber, Gerhard A1 - Preißinger, Markus A1 - Petrasch, Jörg T1 - State estimation of resistive domestic hot water heaters in arbitrary operation modes for demand side management JF - Thermal Science and Engineering Progress KW - Demand side management KW - Domestic hot water heater KW - Prediction error method KW - State estimation KW - System identification Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.tsep.2018.11.003 SN - 2451-9049 VL - o.Jg IS - Bd. 9 SP - 94 EP - 109 ER - TY - CHAP A1 - Horn, Sierk A1 - Holden, Nigel ED - Cook, Gary ED - Johns, Jennifer ED - McDonald, Frank ED - Beaverstock, Jonathan ED - Pandit, Naresh T1 - Language and the development of trade networks in Early Modern Europe: modern reflexes, unexpected consequences T2 - The Routledge companion to the geography of international business Y1 - 2018 SN - 978-1-138-95334-5 SP - 394 EP - 409 PB - Routledge CY - Abingdon, Oxon u.a. ER - TY - CHAP A1 - Ritter, Walter A1 - Kempter, Guido A1 - Hämmerle, Isabella A1 - Wohlgenannt, Andreas ED - Kurosu, Masaaki T1 - Automatic low-level overlays on presentations to support regaining an audience’s attention T2 - Human-computer interaction. Theories, methods, and human issues. 20th International Conference, HCI International 2018. Las Vegas, NV, USA, July 15–20, 2018. Proceedings, Part I Y1 - 2018 SN - 978-3-319-91237-0 978-3-319-91238-7 U6 - http://dx.doi.org/10.1007/978-3-319-91238-7_35 SP - 429 EP - 440 PB - Springer CY - Cham ER - TY - CHAP A1 - Ritter, Walter A1 - Kempter, Guido A1 - Jochum, Markus ED - Jost, Patrick ED - Kempter, Guido T1 - Genetic Design als neuer Ansatz für die fortlaufende Anpassung von grafischen Arbeitsoberflächen T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 52 EP - 59 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Duden, Antje ED - Wilms, Falko ED - Größler, Andreas T1 - Chancen zum Lernen nutzen T2 - Volatilität, Unsicherheit, Komplexität, Ambiguität – kybernetische Ansätze für die Unternehmensführung. Konferenz für Wirtschafts- und Sozialkybernetik vom 8. bis 9. November 2016 in Dornbirn KW - Konferenzschrift Y1 - 2018 SN - 978-3-428-55557-4 SP - 127 EP - 135 PB - Duncker & Humblot CY - Berlin ER - TY - CHAP A1 - Kempter, Guido A1 - Jost, Patrick A1 - Künz, Andreas ED - Wörwag, Sebastian ED - Cloots, Alexandra T1 - Gut zu wissen: technologiegestütztes Lernen während der Arbeit T2 - Zukunft der Arbeit – Perspektive Mensch. Aktuelle Forschungserkenntnisse und Good Practices Y1 - 2018 SN - 978-3-658-22098-3 SP - 205 EP - 215 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Hämmerle, Isabella A1 - Jost, Patrick A1 - Künz, Andreas ED - Jost, Patrick ED - Kempter, Guido T1 - Die Rolle des Menschen und der Gestaltung von Mensch-Maschine-Schnittstellen im Industrie 4.0 Kontext T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 4 EP - 12 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Dorn, Sonia A1 - Jost, Patrick A1 - Gasser, Natascha ED - Jost, Patrick ED - Kempter, Guido T1 - Förderung der Arbeitssicherheit durch illustratives Storytelling in digitalen Arbeits- und Lernanwendungen T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 80 EP - 90 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Seyringer, Dana A1 - Burtscher, Catalina A1 - Edlinger, Johannes A1 - Drexler, Wolfgang A1 - Rank, Elisabeth A1 - Muellner, Paul A1 - Hainberger, Rainer A1 - Maese-Novo, Alejandro A1 - Vlaskovic, Marko A1 - Zimmermann, Horst A1 - Kraft, Jochen A1 - Koppitsch, Günther A1 - Sagmeister, Martin A1 - Meinhardt, Gerald ED - Panchapakesan, Balaji ED - Sakdinawat, Anne ED - Attias, Andre-Jean ED - Dobisz, Elizabeth T1 - Size reduction of high-channel Si3N4 based AWG-spectrometer for medical applications T2 - Nanoengineering: Fabrication, Properties, Optics, and Devices XV. 21–23 August 2018. San Diego, California, United States Y1 - 2018 U6 - http://dx.doi.org/10.1117/12.2319670 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Seyringer, Dana A1 - Maese-Novo, Alejandro A1 - Muellner, Paul A1 - Hainberger, Rainer A1 - Kraft, Jochen A1 - Koppitsch, Günther A1 - Meinhardt, Gerald A1 - Sagmeister, Martin ED - Raposo, Maria ED - Ribeiro, Paulo T1 - Design and optimization of high-channel Si3N4 based AWGs for medical applications T2 - Photoptics 2018. Proceedings of the 6th International Conference on Photonics, Optics and Laser Technology. Funchal, Madeira - Portugal. January 25-27, 2018 Y1 - 2018 SN - 978-989-758-286-8 SP - 213 EP - 220 PB - SCITEPRESS - Science and Technology Publications, Lda CY - (Setubal) ER - TY - CHAP A1 - Seyringer, Dana A1 - Chovan, Jozef A1 - Burtscher, Catalina A1 - Gajdosova, Lenka A1 - Figura, Daniel A1 - Uherek, Frantisek ED - Breza, Juraj ED - Donoval, Daniel ED - Vavrinsky, Erik T1 - Design and optimization of silicon nitride based 1x8 Y-branch splitter T2 - ASDAM 2018. Conference Proceedings. The Twelfth International Conference on Advanced Semiconductor Devices and Microsystems. Smolenice Castle, Slovakia. 21-24 October 2018 Y1 - 2018 U6 - http://dx.doi.org/10.1109/ASDAM.2018.8544615 SP - 85 EP - 88 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Pudis, Dusan A1 - Gaso, Peter A1 - Goraus, Matej A1 - Seyringer, Dana A1 - Burtscher, Catalina ED - Michalka, Miroslav ED - Vincze, Andrej T1 - Polymer based Y-branch and MMI Splitter with planar and 3D geometry T2 - 20. Skola Vakuovej Techniky. Nanonelektronika a Vakuum. Nanoelectronics and Vacuum. Zbornik prispevkov. 23. - 26. oktober 2018. Strbske Pleso Y1 - 2018 SN - 978-80-999050-0-0 SP - 70 EP - 73 PB - Slovenska vakuova spolocnost CY - Bratislava ER - TY - JOUR A1 - Yuan, Xueyong A1 - Weyhausen-Brinkmann, Fritz A1 - Martin-Sanchez, Javier A1 - Piredda, Giovanni A1 - Krapek, Vlastimil A1 - Huo, Yongheng A1 - Huang, Huiying A1 - Schimpf, Christian A1 - Schmidt, Oliver A1 - Edlinger, Johannes A1 - Bester, Gabriel A1 - Trotta, Rinaldo A1 - Rastelli, Armando T1 - Uniaxial stress flips the natural quantization axis of a quantum dot for integrated quantum photonics JF - Nature Communications Y1 - 2018 U6 - http://dx.doi.org/10.1038/s41467-018-05499-5 SN - 2041-1723 VL - 9. Jg ER - TY - JOUR A1 - Kriz, Willy Christian A1 - Manahl, Werner T1 - Gaming simulation for business and management education – a case example of an University curriculum and didactic approach JF - The liberal arts journal Y1 - 2018 VL - 1. Jg. IS - 1 SP - 8 EP - 28 ER - TY - CHAP A1 - Meusburger, Magdalena A1 - Wilms, Falko ED - Duden, Antje T1 - Zusammenarbeit T2 - Zusammenarbeit analog und digital Y1 - 2018 SN - 978-3-96138-109-8 SP - 15 EP - 19 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - BOOK A1 - Pußwald, Bettina A1 - Falkner, Angelina A1 - Gruber, Werner A1 - Jenny, Friz A1 - Kernmayer, Barbara A1 - Kranebitter, Alexandra A1 - Mayer-Schulz, Barbara A1 - Reitmeir, Ulrike A1 - Sutterlüty, Rita A1 - Wörz, Barbara A1 - Hefel, Johanna T1 - Soziale Arbeit in Hospiz und Palliative Care. Standards, Kompetenz- und Tätigkeitsprofil Y1 - 2018 PB - Österreichische Palliativgesellschaft CY - Wien ER - TY - CHAP A1 - Gajdosova, Lenka A1 - Seyringer, Dana A1 - Burtscher, Catalina A1 - Chovan, Jozef A1 - Kuzma, Anton A1 - Uherek, Frantisek ED - Sitek, Jozef ED - Vajda, Jan ED - Jamnicky, Igor T1 - Simulation of silicon nitride based arrayed waveguide gratings applying three different photonics tools T2 - Applied Physics of Condensed Matter (APCOM 2018). Strbske Pleso, Slovak Republic. 20-22 June 2018 Y1 - 2018 PB - AIP Publishing CY - Melville, NY ER - TY - CHAP A1 - Kutluk, Hazal A1 - Bruch, Richard A1 - Meirich, Mailin A1 - Partel, Stefan A1 - Urban, Gerald A1 - Dincer, Can T1 - Microfluidic biosensor for the electrochemical on-site detection of microRNAs T2 - µTAS 2018. MicroTAS2018. The 22nd International Conference on Miniaturized Systems for Chemistry and Life Sciences. Kaohsiung, Taiwan. 11-15 November 2018 Y1 - 2018 SP - 2445 EP - 2446 PB - MicroTAS 2018 Conference CY - San Diego, California ER - TY - JOUR A1 - Preißinger, Markus T1 - Bilge water treatment and desalination based on HDH technology: an experimental investigation of a demonstration plant JF - Desalination and Water Treatment KW - Bilge water KW - Desalination KW - HDH KW - Heat pump KW - Wastewater treatment Y1 - 2018 U6 - http://dx.doi.org/10.5004/dwt.2018.22532 VL - o.Jg IS - Bd. 127 SP - 50 EP - 56 ER - TY - CHAP A1 - Hefel, Johanna ED - European Social Work Research Association, T1 - Loss, death and dying in the context of social work studies in Austria T2 - 8th European Conference for Social Work Research. Book of Abstracts. 18-20 April, 2018 Y1 - 2018 SN - 978-1-9999205-7-9 SP - 23 EP - 24 PB - University of Edinburgh CY - Edinburgh ER - TY - CHAP A1 - Hefel, Johanna T1 - Human mortality in the context of social work: a neglected issue T2 - CDAS Conference 2018. The Politics of Death. 08-09 June 2018. The Edge, University of Bath. Book of Abstracts Y1 - 2018 SP - 6 EP - 7 PB - Centre for Death & Society (CDAS) CY - Bath ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Stamatov, Denise A1 - Marinov, Marin T1 - Mixed reality smart glasses application for interactive working T2 - 2018 IEEE XXVII International Scientific Conference Electronics (ET). Proceedings. September 13 - 15, 2018. Sozopol, Bulgaria KW - 3D manipulations KW - 3D modeling KW - 3D objects KW - 3D rigid objects KW - augmented KW - Cameras KW - Electron tubes KW - helmet mounted displays KW - human-computer interaction KW - interactive application KW - interactive working KW - Microsoft HoloLens KW - Microsoft HoloLens head KW - Microsoft Windows KW - mixed reality KW - mixed reality smart glasses application KW - spatial interaction KW - Three-dimensional displays KW - Tools KW - user-friendly application KW - virtual realities KW - virtual reality KW - Visualization KW - VR environment Y1 - 2018 SN - 978-1-5386-6692-0 U6 - http://dx.doi.org/10.1109/ET.2018.8549615 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kikkawa, Toshiko A1 - Sugiura, Junkichi A1 - Kriz, Willy ED - Lukosch, Heide ED - Bekebrede, Geertje ED - Kortmann, Rens T1 - The effects of debriefing on the performance and attitude of Japanese university students T2 - Simulation Gaming. Applications for Sustainable Cities and Smart Infrastructures. 48th International Simulation and Gaming Association Conference, ISAGA 2017. Delft, The Netherlands, July 10-14, 2017. Revised Selected Papers Y1 - 2018 SN - 978-3-319-91901-0 978-3-319-91902-7 U6 - http://dx.doi.org/10.1007/978-3-319-91902-7_17 SP - 173 EP - 180 PB - Springer CY - Cham ER - TY - CHAP A1 - Kriz, Willy A1 - Kikkawa, Toshiko A1 - Sugiura, Junkichi T1 - The effects of debriefing on attitudes of Japanese university students T2 - Who bears S/G 10 years from now? 2018 Spring National Conference. May 26, 27. Tokyo Institute of Technology. Proceedings of JASAG National Conference Y1 - 2018 SP - 58 EP - 59 PB - Tokyo Institute of Technology CY - Tokyo ER - TY - CHAP A1 - Gajdosova, Lenka A1 - Seyringer, Dana A1 - Gaso, Peter A1 - Pudis, Dusan ED - Michalka, Miroslav ED - Vincze, Andrej T1 - Design and simulation of PDMS polymer based 1X4 Y-branch splitter T2 - 20. Skola Vakuovej Techniky. Nanonelektronika a Vakuum. Nanoelectronics and Vacuum. Zbornik prispevkov. 23. - 26. oktober 2018. Strbske Pleso Y1 - 2018 SN - 978-80-999050-0-0 SP - 90 EP - 93 PB - Slovenska vakuova spolocnost CY - Bratislava ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Burtscher, Catalina A1 - Kuzma, Anton A1 - Chovan, Jozef A1 - Uherek, Frantisek ED - Sitek, Jozef ED - Vajda, Jan ED - Jamnicky, Igor T1 - Design of low loss silicon nitride 8-channel AWG T2 - Applied Physics of Condensed Matter (APCOM 2018). Strbske Pleso, Slovak Republic. 20-22 June 2018 Y1 - 2018 PB - AIP Publishing CY - Melville, NY ER - TY - CHAP A1 - Wilms, Falko ED - Wilms, Falko ED - Größler, Andreas T1 - Unternehmensführung in der VUCA-Welt T2 - Volatilität, Unsicherheit, Komplexität, Ambiguität – kybernetische Ansätze für die Unternehmensführung. Konferenz für Wirtschafts- und Sozialkybernetik vom 8. bis 9. November 2016 in Dornbirn KW - Konferenzschrift Y1 - 2018 SN - 978-3-428-55557-4 SP - 9 EP - 19 PB - Duncker & Humblot CY - Berlin ER - TY - JOUR A1 - Fäßler, Bernhard A1 - Kepplinger, Peter A1 - Petrasch, Jörg T1 - Field testing of repurposed electric vehicle batteries for price-driven grid balancing JF - Journal of Energy Storage KW - Autonomous optimization KW - Distributed storage KW - Grid balancing KW - Modeling KW - Repurposed vehicle ZEBRA battery Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.est.2018.10.010 SN - 2352-152X VL - o.Jg IS - Bd. 21 SP - 40 EP - 47 ER - TY - CHAP A1 - Kriz, Willy ED - Meßner, Maria ED - Schedelik, Michael ED - Engartner, Tim T1 - Planspiele als Trainingsmethode in der Hochschuldidaktik: Zur Funktion der Planspielleitung T2 - Handbuch Planspiele in der sozialwissenschaftlichen Hochschullehre Y1 - 2018 SN - 978-3-7344-0644-7 SP - 43 EP - 56 PB - Wochenschau Verlag CY - Frankfurt/M. ER - TY - CHAP A1 - Matt, Hubert ED - Ebertshäuser, Ephraim T1 - Designkritik ist zumeist einfach die Geste der Verweigerung oder Ignoranz. Eine erste Annäherung T2 - Was bedeutet für mich Designkritik? Eine Frage. Zwanzig Antworten Y1 - 2018 SP - 29 EP - 32 PB - Prima CY - Basel u.a. ER - TY - CHAP A1 - Zehetner, Johann A1 - Kasemann, Stephan A1 - Vanko, Gabriel A1 - Babchenko, Oleg ED - Breza, Juraj ED - Donoval, Daniel ED - Vavrinsky, Erik T1 - Black titanium dioxide in situ generated on femtosecond laser induced periodic surface structures T2 - ASDAM 2018. Conference Proceedings. The Twelfth International Conference on Advanced Semiconductor Devices and Microsystems. Smolenice Castle, Slovakia. 21-24 October 2018 Y1 - 2018 U6 - http://dx.doi.org/10.1109/ASDAM.2018.8544516 SP - 203 EP - 206 PB - IEEE CY - Piscataway, NJ ER - TY - BOOK A1 - Matt, Hubert ED - allerArt - Verein zur Förderung von Kunst und Kultur in Bludenz, T1 - Da nach - Versuch über Ingo Springenschmid. Zur Ausstellung von Ingo Springenschmid in der Galerie allerArt von 16. Juni bis 19. August 2018 Y1 - 2018 PB - allerArt CY - Bludenz ER - TY - CHAP A1 - Mayer, Horst ED - Duden, Antje T1 - Digitale Kommunikation im Unternehmen T2 - Zusammenarbeit analog und digital Y1 - 2018 SN - 978-3-96138-109-8 SP - 21 EP - 74 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - JOUR A1 - Kriz, Willy T1 - Research of the active substance of gaming simulation JF - Simulation & Gaming Y1 - 2018 U6 - http://dx.doi.org/10.1177/1046878118817847 VL - 49. Jg IS - H. 6 SP - 595 EP - 601 ER - TY - CHAP A1 - Wilms, Falko ED - Duden, Antje T1 - Praxis und/oder Theorie T2 - Zusammenarbeit analog und digital Y1 - 2018 SN - 978-3-96138-109-8 SP - 75 EP - 87 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Horn, Sierk A1 - Wittek, Bernhard A1 - Iguchi, Chie ED - McCarthy, Mary T1 - Japanese foreign direct investment in Thailand: promoting an ‘interactive’ institutional approach T2 - Routledge handbook of Japanese foreign policy Y1 - 2018 SN - 978-1-317-28492-5 SP - 281 EP - 305 PB - Routledge CY - Abingdon, Oxon u.a. ER - TY - CHAP A1 - Seyringer, Dana ED - Michalka, Miroslav ED - Vincze, Andrej T1 - AWG-spectrometer for medical applications T2 - 20. Skola Vakuovej Techniky. Nanonelektronika a Vakuum. Nanoelectronics and Vacuum. Zbornik prispevkov. 23. - 26. oktober 2018. Strbske Pleso Y1 - 2018 SN - 978-80-999050-0-0 PB - Slovenska vakuova spolocnost CY - Bratislava ER - TY - CHAP A1 - Seyringer, Dana ED - Kayahan, Ersin ED - Oral, Ahmet ED - Aköz, Mehmet ED - Aksan, Onur T1 - Arrayed waveguide gratings: design and applications T2 - Interphotonics 2018. Book of abstracts. International Conference on Photonics Research. October 8-12, 2018. Antalya, Turkey Y1 - 2018 ER - TY - CHAP A1 - Seyringer, Dana T1 - Design und Simulation eines optischen Spektrometers T2 - VTT. Vorarlberger Technik Tag 2018. Dienstag, 16. Jänner 2018. FH Vorarlberg Y1 - 2018 ER - TY - CHAP A1 - Horn, Sierk ED - Buckley, Peter ED - Enderwick, Peter ED - Cross, Adam T1 - Marketing strategies T2 - International business Y1 - 2018 SP - 379 EP - 418 PB - Oxford University Press CY - Oxford ER - TY - CHAP A1 - Weiß, Andreas A1 - Popp, Tobias A1 - Zinn, Gerd A1 - Preißinger, Markus A1 - Brüggemann, Dieter ED - Riehl, Roger ED - Preißinger, Markus ED - Eames, Ian ED - Tierney, Mike T1 - A micro-turbine-generator-construction-kit (MTG-c-kit) for small-scale waste heat recovery ORC-plants T2 - Heat Powered Cycles Conference. University of Bayreuth, Germany. 16th-19th September 2018. Conference Proceedings Y1 - 2018 SN - 978-0-9563329-6-7 SP - 358 EP - 364 PB - Heat Powered Cycles CY - o.O. ER - TY - JOUR A1 - Weiß, Andreas A1 - Popp, Tobias A1 - Müller, Jonas A1 - Hauer, Josef A1 - Brüggemann, Dieter A1 - Preißinger, Markus T1 - Experimental characterization and comparison of an axial and a cantilever micro-turbine for small-scale Organic Rankine Cycle JF - Applied Thermal Engineering Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.applthermaleng.2018.05.033 SN - 13594311 VL - o.Jg IS - Bd. 140 SP - 235 EP - 244 ER - TY - CHAP A1 - Preißinger, Markus ED - Riehl, Roger ED - Preißinger, Markus ED - Eames, Ian ED - Tierney, Mike T1 - Bubble columns in humidification dehumidification technology: from a demonstration unit to fundamental research in optical accessible laboratory bubble columns T2 - Heat Powered Cycles Conference. University of Bayreuth, Germany. 16th-19th September 2018. Conference Proceedings Y1 - 2018 SN - 978-0-9563329-6-7 SP - 44 EP - 50 PB - Heat Powered Cycles CY - o.O. ER - TY - BOOK ED - Riehl, Roger ED - Preißinger, Markus ED - Eames, Ian ED - Tierney, Mike T1 - Heat Powered Cycles Conference. University of Bayreuth, Germany. 16th-19th September 2018. Conference Proceedings Y1 - 2018 SN - 978-0-9563329-6-7 PB - Heat Powered Cycles CY - o.O. ER - TY - CHAP A1 - Grobner, Marianne ED - Orthey, Astrid ED - Laske, Stephan ED - Schmid, Michael T1 - Eine Firma - eine Sprache - eine Kultur? Wie sich interkulturelle Unterschiede auf die Zusammenarbeit auswirken und wie die Personalentwicklung darauf reagieren kann T2 - Personal Entwickeln. Das aktuelle Nachschlagewerk für Praktiker Y1 - 2018 PB - Deutscher Wirtschaftsdienst CY - Köln ER - TY - CHAP A1 - Schuler, Michael A1 - Faessler, Bernhard A1 - Preißinger, Markus A1 - Kepplinger, Peter ED - Fachhochschule Salzburg GmbH, T1 - A method for grid simulation assessing demand side management strategies T2 - FH Forschungsforum 2018. Tagungsband. Technik, Gesundheit, Medien Y1 - 2018 PB - Fachhochschule Salzburg GmbH CY - Puch/Salzburg ER - TY - BOOK ED - Duden, Antje T1 - Zusammenarbeit analog und digital Y1 - 2018 SN - 978-3-96138-109-8 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Zavoianu, Alexandru-Ciprian A1 - Saminger-Platz, Susanne A1 - Entner, Doris A1 - Prante, Thorsten A1 - Hellwig, Michael A1 - Schwarz, Martin A1 - Fink, Klara ED - Andres-Perez, Esther ED - Gonzalez, Leo ED - Periaux, Jacques ED - Gauger, Nicolas ED - Quagliarella, Domenico ED - Giannakoglou, Kyriakos T1 - On the optimization of 2D path network layouts in engineering designs via evolutionary computation techniques T2 - Evolutionary and deterministic methods for design optimization and control with applications to industrial and societal problems Y1 - 2018 SP - 307 EP - 322 PB - Springer CY - Cham ER - TY - JOUR A1 - Zavoianu, Alexandru-Ciprian A1 - Saminger-Platz, Susanne A1 - Entner, Doris A1 - Prante, Thorsten A1 - Hellwig, Michael A1 - Schwarz, Martin A1 - Fink, Klara T1 - Multi-objective optimal design of obstacle-avoiding two-dimensional Steiner Trees with application to ascent assembly engineering JF - Journal of Mechanical Design Y1 - 2018 U6 - http://dx.doi.org/10.1115/1.4039009 SN - 1050-0472 VL - 140. Jg IS - H. 6/061401 ER - TY - CHAP A1 - Hellwig, Michael A1 - Entner, Doris A1 - Prante, Thorsten A1 - Zavoianu, Alexandru-Ciprian A1 - Schwarz, Martin A1 - Fink, Klara ED - Andres-Perez, Esther ED - Gonzalez, Leo ED - Periaux, Jacques ED - Gauger, Nicolas ED - Quagliarella, Domenico ED - Giannakoglou, Kyriakos T1 - Optimization of ascent assembly design based on a combinatorial problem representation T2 - Evolutionary and deterministic methods for design optimization and control with applications to industrial and societal problems Y1 - 2018 SP - 291 EP - 306 PB - Springer CY - Cham ER - TY - JOUR A1 - Wilms, Falko T1 - Reflexive Kommunikation als zentraler Erfolgsfaktor des Managements JF - TrainerJournal Y1 - 2018 UR - https://trainertreffen.de/tj/93/catalog_16317641/catalog_16317641/html5.html#/32 VL - o.Jg IS - H. 93 ER - TY - CHAP A1 - Spettel, Patrick A1 - Beyer, Hans-Georg T1 - A simple approach for constrained optimization - an evolution strategy that evolves rays T2 - 2018 IEEE Congress on Evolutionary Computation (CEC). Proceedings KW - ad hoc networks KW - ad hoc optimization approach KW - constrained optimization problems KW - Covariance matrices KW - differential evolution KW - evolution strategy KW - evolutionary computation KW - Gaussian distribution KW - HappyCat KW - Linear programming KW - Minimization KW - Optimization KW - Ray-ES algorithm KW - real-parameter optimization problem KW - Search problems KW - Upper bound Y1 - 2018 SN - 978-1-5090-6017-7 U6 - http://dx.doi.org/10.1109/CEC.2018.8477753 SP - 298 EP - 305 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Csiszar, Imre A1 - Breuer, Thomas T1 - Expected value minimization in information theoretic multiple priors models JF - IEEE Transactions on Information Theory KW - Bregman distance KW - Bregman distance ball KW - Convex functions KW - convex integral functional KW - Entropy KW - expected value minimization KW - f-divergence KW - f-divergence ball KW - finance KW - generalized exponential family KW - I-divergence ball KW - information geometry KW - information theoretic multiple priors KW - level set KW - Mathematical model KW - minimisation KW - Minimization KW - plausible prior distributions KW - probability KW - Random variables KW - risk measure Y1 - 2018 U6 - http://dx.doi.org/10.1109/TIT.2018.2827364 SN - 0018-9448 VL - 64. Jg IS - H. 6 SP - 3957 EP - 3974 ER - TY - JOUR A1 - Loshchilov, Ilya A1 - Glasmachers, Tobias A1 - Beyer, Hans-Georg T1 - Large scale black-box optimization by limited-memory matrix adaptation JF - IEEE Transactions on Evolutionary Computation KW - Covariance matrices KW - Electronic mail KW - Evolution (biology) KW - Manganese KW - Optimization KW - Time complexity Y1 - 2018 U6 - http://dx.doi.org/10.1109/TEVC.2018.2855049 SN - 1089-778X VL - Bd. 23 IS - H. 2 SP - 353 EP - 358 ER - TY - JOUR A1 - Ager, Clemens A1 - Unterkofler, Karl A1 - Mochalski, Pawel A1 - Teschl, Susanne A1 - Teschl, Gerald A1 - Mayhew, Chris A1 - King, Julian T1 - Modeling-based determination of physiological parameters of systemic VOCs by breath gas analysis, part 2 JF - Journal of Breath Research Y1 - 2018 U6 - http://dx.doi.org/10.1088/1752-7163/aab2b6 SN - 1752-7163 VL - 12. Jg IS - H. 3/036011 ER - TY - JOUR A1 - Spettel, Patrick A1 - Beyer, Hans-Georg T1 - Analysis of the (1,λ)-σ-self-adaptation evolution strategy with repair by projection applied to a conically constrained problem JF - Theoretical Computer Science KW - Conically constrained problem KW - Evolution strategies KW - Repair by projection Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.tcs.2018.10.036 SN - 0304-3975 N1 - nov, Veröffentlichungsdatum Web: 9. November 2018. In Press, Corrected Proof VL - o.Jg. IS - Bd. 785 SP - 30-45 ER - TY - JOUR A1 - Hellwig, Michael A1 - Beyer, Hans-Georg T1 - Benchmarking evolutionary algorithms for single objective real-valued constrained optimization – a critical review JF - Swarm and Evolutionary Computation Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.swevo.2018.10.002 SN - 22106502 VL - o.Jg IS - Bd. 44 SP - 927 EP - 944 ER - TY - JOUR A1 - Hellwig, Michael A1 - Beyer, Hans-Georg T1 - On the steady state analysis of covariance matrix self-adaptation evolution strategies on the noisy ellipsoid model JF - Theoretical Computer Science Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.tcs.2018.05.016 SN - 0304-3975 ER - TY - CHAP A1 - Finck, Steffen A1 - Feilhauer, Thomas A1 - Kepplinger, Peter ED - Fachhochschule Salzburg GmbH, T1 - Josef Ressel Zentrum für angewandtes wissenschaftliches Rechnen in Energie, Finanzwirtschaft und Logistik an der Fachhochschule Vorarlberg T2 - FH Forschungsforum 2018. Tagungsband. Technik, Gesundheit, Medien Y1 - 2018 PB - Fachhochschule Salzburg GmbH CY - Puch/Salzburg ER - TY - CHAP A1 - Hellwig, Michael A1 - Beyer, Hans-Georg T1 - A matrix adaptation evolution strategy for constrained real-parameter optimization T2 - 2018 IEEE Congress on Evolutionary Computation (CEC). Proceedings Y1 - 2018 SN - 978-1-5090-6017-7 U6 - http://dx.doi.org/10.1109/CEC.2018.8477950 SP - 749 EP - 756 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Spettel, Patrick A1 - Beyer, Hans-Georg A1 - Hellwig, Michael T1 - A covariance matrix self-adaptation evolution strategy for optimization under linear constraints JF - IEEE Transactions on Evolutionary Computation Y1 - 2018 U6 - http://dx.doi.org/10.1109/TEVC.2018.2871944 SN - 1089-778X N1 - Veröffentlichungsdatum Web: 24. September 2018. Early Access VL - 23. Jg. IS - H. 3 SP - 514 EP - 524 ER - TY - CHAP A1 - Ströbl, Stephan A1 - Eisel, Max A1 - Pongratz, Thomas A1 - Strittmatter, Frank A1 - Sroka, Ronald T1 - Investigation in laser lithotripsy. Propulsion, fragmentation and fluorescence T2 - Sino-German Photomedicine Symposium. 2018, 25.5-27.5 Y1 - 2018 SP - 30 EP - 33 PB - Shanghai Medical Association CY - Shanghai ER - TY - CHAP A1 - Hellwig, Michael A1 - Beyer, Hans-Georg ED - Fagan, David ED - Martin-Vide, Carlos ED - O’Neill, Michael ED - Vega-Rodriguez, Miguel T1 - A linear constrained optimization benchmark for probabilistic search algorithms: the rotated Klee-Minty problem T2 - Theory and practice of natural computing. 7th International Conference, TPNC 2018, Dublin, Ireland, December 12-14, 2018. Proceedings Y1 - 2018 SN - 978-3-030-04069-7 978-3-030-04070-3 U6 - http://dx.doi.org/10.1007/978-3-030-04070-3_11 SP - 139 EP - 151 PB - Springer CY - Cham ER - TY - RPRT A1 - Spettel, Patrick A1 - Beyer, Hans-Georg T1 - Technical report: analysis of the (1, λ)-σ-self-adaptation evolution strategy with repair by projection applied to a conically constrained problem Y1 - 2018 UR - https://www.fhv.at/fileadmin/user_upload/fhv/files/forschung/ppe/working-papers/Analysis_onecommalambdasigmaSA-ES_Projection_Cone_TR.pdf CY - Dornbirn ER - TY - CHAP A1 - Weber, Heidi A1 - Cruz Rodriguez, Antonio A1 - Mateus, Américo ED - Duarte, Emilia T1 - Deconstructing the creative processes in design thinking T2 - Proceedings of the Design Doctoral Conference ’18. Transgression. IADE, Universidade Europeia Lisbon, 20th 21st 22nd of June ’18 Y1 - 2018 UR - https://www.unidcom-iade.pt/wp-content/uploads/2018/11/DDC-18-web.pdf?fbclid=IwAR0WNHb-11iwah_3K2c7KlbWHsoxo0D_hBM7AoyKlup-_0On5jdfk0OHVWw SN - 978-989-8473-25-7 SP - 93 EP - 100 PB - Edicoes IADE CY - Lisbon ER - TY - CHAP A1 - Ströbl, Stephan A1 - Vonach, Christoph A1 - Gratt, Johannes A1 - Domke, Matthias A1 - Sroka, Ronald T1 - Ultrafast-laser manufacture of radially emitting optical fiber diffusers for medical applications T2 - Proceedings of LPM2018. The 19th International Symposium on Laser Precision Microfabrication. Edinburgh Conference Centre, Heriot-Watt University, Edinburgh, UK 25-28 June, 2018 Y1 - 2018 UR - http://www.jlps.gr.jp/en/proc/lpm/18/ N1 - Veröffentlichungsdatum Web: 20. August 2018 IS - #18-054 ER - TY - JOUR A1 - Chien, Huei-Ting A1 - Pilat, Florian A1 - Griesser, Thomas A1 - Fitzek, Harald A1 - Poelt, Peter A1 - Friedel, Bettina T1 - Influence of environmentally affected hole-transport layers on spatial homogeneity and charge-transport dynamics of organic solar cells JF - ACS Applied Materials & Interfaces Y1 - 2018 U6 - http://dx.doi.org/10.1021/acsami.7b19442 VL - 10. Jg IS - H. 12 SP - 10102 EP - 10114 ER - TY - CHAP A1 - Baumeister, Alexander A1 - Ilg, Markus T1 - Real options in agile software development: handling the paradox of flexibility and behavioural stickiness in project valuation T2 - ECIS 2018. European Conference on Information Systems 2018. June 23rd – 28th 2018 / Portsmouth, UK. Beyond Digitization – Facets of Socio-Technical Change Y1 - 2018 UR - http://ecis2018.eu/wp-content/uploads/2018/09/1192-doc.pdf PB - University of Portsmouth CY - Portsmouth ER - TY - BOOK ED - Wilms, Falko ED - Größler, Andreas T1 - Volatilität, Unsicherheit, Komplexität, Ambiguität – kybernetische Ansätze für die Unternehmensführung. Konferenz für Wirtschafts- und Sozialkybernetik vom 8. bis 9. November 2016 in Dornbirn T3 - Wirtschaftskybernetik und Systemanalyse, 32 Y1 - 2018 SN - 978-3-428-55557-4 PB - Duncker & Humblot CY - Berlin ER - TY - BOOK ED - Jost, Patrick ED - Kempter, Guido T1 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 KW - +TEA 635 KW - +WAC 540 KW - Arbeit KW - Technischer Fortschritt Y1 - 2018 SN - 978-3-95853-405-6 PB - Pabst Science Publishers CY - Lengerich ER - TY - RPRT A1 - Breuer, Thomas A1 - Summer, Martin T1 - Systematic systemic stress tests Y1 - 2018 UR - https://www.oenb.at/Publikationen/Volkswirtschaft/Working-Papers.html CY - Vienna ER - TY - JOUR A1 - Kriz, Willy A1 - Harviainen, J. Tuomas A1 - Clapper, Timothy T1 - Game science: foundations and perspectives JF - Simulation & Gaming Y1 - 2018 U6 - http://dx.doi.org/10.1177/1046878118781631 VL - 49. Jg IS - H. 3 SP - 199 EP - 206 ER - TY - JFULL ED - Clapper, Timothy ED - Harviainen, J. Tuomas ED - Kriz, Willy T1 - Simulation & Gaming. An Interdisciplinary Journal of Theory, Practice and Research Y1 - 2018 VL - 49 ER - TY - CHAP A1 - Maurer, Florian A1 - Fritzsche, Albrecht ED - Pucihar, Andreja ED - Kljajic Borstnar, Mirjana ED - Ravesteijn, Pascal ED - Seitz, Juergen ED - Bons, Roger T1 - Boosting innovation for the development of smart-service factories of the future: the cases of the federal state of Vorarlberg and its neighbouring regions T2 - 31st Bled eConference. Digital Transformation. Meeting the Challenges. June 17 – 20, 2018 , Bled, Slovenia. Conference Proceedings Y1 - 2018 U6 - http://dx.doi.org/10.18690/978-961-286-170-4.24 SP - 357 EP - 373 PB - University of Maribor Press CY - Maribor ER - TY - CHAP A1 - Ilg, Markus A1 - Hebertinger, Martin ED - Nadig, Linard ED - Egle, Ulrich T1 - Einsatz eines haptischen Planspiels mit cloudbasierter Unterstützung in einer BWL‐Einführungsveranstaltung T2 - CARF Luzern 2018. Controlling. Accounting. Risiko. Finanzen. Konferenzband Y1 - 2018 UR - https://www.hslu.ch/-/media/campus/common/files/dokumente/w/ifz/seminare-konferenzen/carf/konferenzband-carf-luzern-2018.pdf?la=de-ch SP - 330 EP - 351 PB - Verlag IFZ - Hochschule Luzern CY - Zug ER - TY - JOUR A1 - Kettner, Olivia A1 - Simic, Sanja A1 - Kunert, Birgit A1 - Schennach, Robert A1 - Resel, Roland A1 - Grießer, Thomas A1 - Friedel, Bettina T1 - Characterization of surface and structure of in situ doped sol‐gel‐derived silicon carbide JF - Advanced Engineering Materials KW - Self‐passivation KW - silicon carbide KW - sol‐gel processing KW - surface termination Y1 - 2018 U6 - http://dx.doi.org/10.1002/adem.201701067 SN - 1438-1656 VL - 20. Jg IS - H. 6/1701067 ER - TY - GEN A1 - Partel, Stefan A1 - Kasemann, Stephan A1 - Dincer, Can A1 - Kieninger, Jochen A1 - Urban, Gerald T1 - US 2018/0106749 A1. Electrode structure and method of manufacturing an electrode structure. 19.04.2018 Y1 - 2018 UR - https://worldwide.espacenet.com/publicationDetails/biblio?FT=D&date=20180419&DB=EPODOC&CC=US&NR=2018106749A1# ER - TY - THES A1 - Metzler, Thomas T1 - Taktiken für rentables Cross-Channel Management Y1 - 2018 CY - Sankt Gallen ER - TY - JOUR A1 - Seyringer, Dana A1 - Burtscher, Catalina A1 - Edlinger, Johannes A1 - Hainberger, Rainer A1 - Koppitsch, Günther A1 - Kraft, Jochen A1 - Maese-Novo, Alejandro A1 - Meinhardt, Gerald A1 - Muellner, Paul A1 - Sagmeister, Martin T1 - Design of 160-channel Si3N4 based AWG-spectrometer for medical applications JF - TechConnect Briefs Y1 - 2018 UR - https://briefs.techconnect.org/papers/design-of-160-channel-si3n4-based-awg-spectrometer-for-medical-applications/ VL - o.Jg IS - Bd. 4: Informatics, Electronics and Microsystems SP - 209 EP - 212 ER - TY - CHAP A1 - Dobler, Martin A1 - Maurer, Florian A1 - Schumacher, Jens ED - Jost, Patrick ED - Kempter, Guido T1 - Daten-getriebene Optimierung von Benutzererfahrungen im Industrie 4.0 Umfeld T2 - Assistenztechnologien in der Arbeitswelt. Beiträge zum Usability Day XVI. 21. Juni 2018 Y1 - 2018 SN - 978-3-95853-405-6 SP - 207 EP - 217 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Maurer, Florian A1 - Schumacher, Jens T1 - Organizational robustness and resilience as catalyst to boost innovation in smart service factories of the future T2 - Conference Proceedings. ICE/IEEE ITMC 2018. Stuttgart, 17.06. - 20.06.18. 2018 IEEE International Conference on Engineering, Technology and Innovation (ICE/ITMC) Y1 - 2018 U6 - http://dx.doi.org/10.1109/ICE.2018.8436364 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Schumacher, Jens A1 - Suzic, Bojana A1 - Dobler, Martin T1 - User-centred innovation design in cities. Collaborative business models T2 - Special Issue. ICE/IEEE ITMC 2018. Stuttgart 17.06. - 20.06.18. 2018 IEEE International Conference on Engineering, Technology and Innovation (ICE/ITMC) Y1 - 2018 SP - 64 EP - 71 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Spellauge, Maximilian A1 - Loghin, Florin-Cristian A1 - Sotrop, Jürgen A1 - Domke, Matthias A1 - Bobinger, Marco A1 - Abdellah, Alaa A1 - Becherer, Markus A1 - Lugli, Paolo A1 - Huber, Heinz T1 - Ultra-short-pulse laser ablation and modification of fully sprayed single walled carbon nanotube networks JF - Carbon Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.carbon.2018.05.074 SN - 0008-6223 VL - o.Jg IS - Bd. 138 SP - 234 EP - 242 ER - TY - JOUR A1 - Domonkos, Maria A1 - Varga, Marian A1 - Ondic, Lukas A1 - Gajdosova, Lenka A1 - Kromka, Alexander T1 - Microsphere lithography for scalable polycrystalline diamond-based near-infrared photonic crystals fabrication JF - Materials and Design KW - Polycrystalline diamond KW - Microsphere lithography KW - Surface roughness KW - Photonic crystal KW - Optical measurements Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.matdes.2017.10.076 N1 - Available online 3 November 2017 VL - o.Jg. IS - Bd. 139 SP - 363 EP - 371 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Diem, Eva A1 - Unterkofler, Karl A1 - Mündlein, Axel A1 - Drexel, Heinz A1 - Mayhew, Chris A1 - Leiherer, Andreas T1 - In vitro profiling of volatile organic compounds released by Simpson-Golabi-Behmel syndrome adipocytes JF - Journal of Chromatography B N2 - Breath analysis offers a non-invasive and rapid diagnostic method for detecting various volatile organic compounds that could be indicators for different diseases, particularly metabolic disorders including type 2 diabetes mellitus. The development of type 2 diabetes mellitus is closely linked to metabolic dysfunction of adipose tissue and adipocytes. However, the VOC profile of human adipocytes has not yet been investigated. Gas chromatography with mass spectrometric detection and head-space needle trap extraction (two-bed Carbopack X/Carboxen 1000 needle traps) were applied to profile VOCs produced and metabolised by human Simpson Golabi Behmel Syndrome adipocytes. In total, sixteen compounds were identified to be related to the metabolism of the cells. Four sulphur compounds (carbon disulphide, dimethyl sulphide, ethyl methyl sulphide and dimethyl disulphide), three heterocyclic compounds (2-ethylfuran, 2-methyl-5-(methyl-thio)-furan, and 2-pentylfuran), two ketones (acetone and 2-pentanone), two hydrocarbons (isoprene and n-heptane) and one ester (ethyl acetate) were produced, and four aldehydes (2-methyl-propanal, butanal, pentanal and hexanal) were found to be consumed by the cells of interest. This study presents the first profile of VOCs formed by human adipocytes, which may reflect the activity of the adipose tissue enzymes and provide evidence of their active role in metabolic regulation. Our data also suggest that a previously reported increase of isoprene and sulphur compounds in diabetic patients may be explained by their production by adipocytes. Moreover, the unique features of this profile, including a high emission of dimethyl sulphide and the production of furan-containing VOCs, increase our knowledge about metabolism in adipose tissue and provide diagnostic potential for future applications. Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.jchromb.2018.11.028 N1 - Available online 28 November 2018 VL - o.Jg (2019) IS - Bd. 1104 SP - 256 EP - 261 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Mirmigkou, Sofia A1 - Unterkofler, Karl A1 - Sulzer, Philipp A1 - Mayhew, Christopher A. A1 - Märk, Tilmann D. T1 - PTR-MS studies of the reactions of H3O+ with a number of deuterated volatile organic compounds and the subsequent sequential reactions of the primary product ions with water under normal and humid drift tube conditions: Implications for use of deuterated compounds for breath analysis JF - International Journal of Mass Spectrometry N2 - Product ion distributions resulting from the primary reactions of H3O+ with nine D-labeled volatile organic compounds and the subsequent sequential reactions with H2O have been determined using a Proton Transfer Reaction Time of Flight Mass Spectrometer (PTR-TOF 8000 (IONICON Analytik GmbH)) at various reduced electric field (E/N) values ranging from 80 up to 150 Td and for two different absolute humidity levels of air sample < 0.1% and 5%. The specific D-labeled compounds used in this study are acetone-d6, toluene-d8, benzene-d6, ethanol-d (C2H5OD), ethanol-d2 (CH3CD2OH), ethanol-d6, 2-propanol-d8, 2-propanol-d3 (CD3CH(OH)CH3), and isoprene-d5 (CH2CHC(CD2)CD3). With the exception of the two 2-propanol compounds, non-dissociative proton transfer is the dominant primary reaction pathway. For 2-propanol-d8 and 2-propanol-d3 the major primary reaction channel involved is dissociative proton transfer. However, unlike their undeuterated counterparts, the primary product ions undergo subsequent deuterium/hydrogen isotope exchange reactions with the ever present water in the drift tube, the extent of which of course depends on the humidity within that tube. This exchange leads to the generation of various isotopologue product ions, the product ion branching percentages of which are also dependent on the humidity in the drift tube. This results in complex mass spectra and the distribution of product ions leads to issues of reduced sensitivity and accuracy. However, the effect of D/H exchange considerably varies between the compounds under study. In the case of acetone-d6 it is very weak (<1%), because the exchange process is not facile when the deuterium is in the methyl functional group. In comparison, the H3O+/ benzene-d6 (C6D6) reaction and sequential reactions with water result in the production of the isotopologue ions C6Dn(H7-n)+ (where n = 0–6). Changing the value of E/N and/or the humidity in the drift tube considerably affects the amount of the isotope exchange reactions and hence the resulting sequential product ion distributions. An important conclusion of the findings from this work is that care must be taken in the choice of an exogenous deuterated compound for use in breath pharmacokinetic studies using proton transfer reaction mass spectrometry; otherwise the resulting D/H exchange processes impose interpretative problems. © 2018 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/). KW - D/H isotopic exchange KW - Deuterated volatile organic compounds KW - Fragmentation patterns KW - HOreactions KW - PTR-TOF-MS Y1 - 2018 U6 - http://dx.doi.org/10.1016/j.ijms.2018.11.007 SN - 1387-3806 VL - o.Jg IS - Bd. 436 SP - 65 EP - 70 ER - TY - THES A1 - Fäßler, Bernhard T1 - Autonomous optimization of repurposed electric vehicle batteries for grid balancing KW - Battery KW - Second use KW - Electric vehicle KW - Grid balancing KW - Autonomous control KW - Optimization Y1 - 2018 SN - 978-82-7117-892-5 SN - 1504-9272 CY - Agder ER - TY - THES A1 - Nachbaur, Rene T1 - Evaluation of tempering as a heat emission system in low-energy residential buildings T1 - Untersuchung von Temperierung als Wärmeabgabesystem in Niederigenergie-Wohnhäuser N2 - In the residential construction industry, the focus on energy efficiency and cost effectiveness has been gaining importance. In order to achieve these contradicting objectives, a shift towards a reduced complexity in building practices can be observed. Within the HVAC sector, the Tempering method for space heating has received particular attention as an alternative way to heat museums and buildings worthy of preservation. In spite of the simplified design, this space heating system is claimed to offer significant advantages in its present field of application. This study evaluates the implementation of Tempering in the residential context. So far, there is no scientific research on the implementation of Tempering in energy efficient-dwellings. This master thesis provides initial results on achievable heat flux values, the impact on heat generation efficiency, the inherent installation costs as well as the particular consequences in terms of end energy consumption of the building as a whole. The findings are compared to the individual performances of well-established heat emission approaches. By means of a numerical analysis and a case study on a real-case single-family home, it is found that the heat flux values of Tempering systems suffice for the implementation within buildings, which comply with the low-energy building standard. Comparing radiant walls, radiant floors and radiators, the inherent installation costs are lowest for Tempering and radiant floors. The impact on the end energy consumption depends largely on the utilised heat generation system. With a gas-condensing boiler, Tempering performs equal to the radiant systems. When a ground source heat pump system is installed, however, Tempering performs poorly and accounts for a significantly increased energy consumption. Radiator systems are found to be the most energy-efficient method for space heating in both cases. N2 - Im Wohnbausektor der Bauindustrie wird der Fokus immer mehr auf die Energieeffizienz und auf eine kostenreduzierte Bauweise gelegt. Um diese widersprüchlichen Zielsetzungen erreichen zu können, ist der Trend von "Low Tech"-Ausführungen zu erkennen, in dem die Komplexität der baulichen Lösungen reduziert wird. Im Haustechnikbereich der Baubranche, hat das Wärmeabgabesystem der Temperierung auf sich aufmerksam gemacht. Dies bisher im Bereich von Museen und Öffentlichen Gebäuden, die saniert wurden. Die Erfinder des Systems versprechen vielfache Vorteile, trotz des stark vereinfachten Aufbaus des Wärmeabgabestystems. Diese Arbeit untersucht die Anwendbarkeit von Temperierung im Niedrigenergie-Wohnbau. Bisher gibt es zu diesem Anwendungsfall sehr wenig wissenschaftliche Untersuchungen. Das Temperierungssystem wird mit den etablierten Wärmeabgabe-Systemen verglichen, in dem die Wärmeabgabe an den Raum, der Wirkungsgrad der Wärmeerzeuger, die anfallenden Kosten sowie der Endenergie-Verbrauch untersucht und gegenübergestellt wird. Anhand einer numerischen Simulation und eines Fallbeispiels an einem realen Einfamilienhaus wird der Systemvergleich durchgeführt. Die Ergebnisse zeigen, dass das Temperierungssystem ausreichend Wärme in die Räume zu bringen vermag. Beim Kostenvergleich stellt sich heraus, dass Temperierung gemeinsam mit der Fußbodenheizung zu den kostengünstigsten Lösungen zählt. Der Endenergieverbrauch ist bei Einsatz eines Gaskondensationskessels mit den Ergebnissen der anderen Flächenheizungssysteme vergleichbar und liegt in etwa gleich. Wenn jedoch eine Wärmepumpe verwendet wird, wirken sich die höheren Vorlauftemperaturen des Temperierungssystems negativ aus. Der Endenergieverbrauch steigt in diesem Fall bedeutend an. In beiden Fällen hat die Studie ergeben, dass die Heizkörperheizung die energetisch effzienteste Raumheizungsmöglichkeit darstellt. KW - Heat emission system KW - Tempering KW - Heat flux KW - End energy consumption Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2769 ER - TY - THES A1 - Gstrein, Michael T1 - Energetic and economic comparison of waste incineration plants and fermentation plants for municipal solid waste in the UK T1 - Energetischer und wirtschaftlicher Vergleich von Abfallverbrennungsanlagen und Fermentationsanlagen für kommunalen Abfall in Großbritannien N2 - The master thesis concentrates on two different cases to generate energy from MSW. In the first case, the MSW is incinerated in an incineration plant. This approach represents the present situation in the waste treatment in large parts of the UK. In the second case, the OFMSW is separated in a treatment facility and used in a fermentation plant. The remaining waste is again used as a feedstock in an incineration plant. The difference in the net energy yield between these two cases is investigated in this thesis. To calculate the difference in the energy yield of case 1 and case 2, a research of the existing literature about comparisons of incineration and fermentation plants and their results are reflected and data about the MSW in the UK is collected. With the input of the literature and the researched data, a model is built which compares the two different cases of waste treatment. The results of the comparisons are then examined by varying different parameters. This step is repeated by using different input parameters. Afterwards, the results are compared and analysed. In the next part of the thesis, an economic analysis of the incineration and fermentation combined technology plant is made. In this analysis, the investment costs, the annual profits and the annual costs of an additional fermentation plant are discussed and calculated. The result of the analysis is displayed as an amortization time calculation. The results are then analysed by varying the parameters in a sensitivity analysis. Finally, the research question is answered and a forecast for possible plant designs with an incineration and a fermentation plant in combination are discussed. N2 - Die Masterarbeit beschäftigt sich mit zwei verschiedenen Anwendungsfällen zur Erzeugung von Energie aus kommunalen Abfällen. Im ersten Fall wird der Abfall aus nicht getrennter kommunaler Sammlung in einer Müllverbrennungsanlage verbrannt. Dieses Verfahren findet derzeit in großen Teilen von Großbritannien statt. Im zweiten Fall wird der organische Anteil des kommunalen Abfalles in einer Aufbereitungsanlage abgetrennt und in eine Fermentationsanlage eingebracht. Der restliche kommunale Abfall wird wiederum in einer Müllverbrennungsanlage verwertet. Mit dieser Arbeit soll der Unterschied zwischen diesen zwei Fällen bezogen auf den Nettoenergieertrag untersucht werden. Um diesen Unterschied zu berechnen, wird zuerst eine Literaturrecherche zu aktuell vorhandenen Vergleichen zwischen Verbrennungs- und Fermentationsanlagen und deren Ergebnisse durchgeführt. Außerdem werden Daten über den kommunalen Abfall in Großbritannien für die spätere Berechnung gesammelt. Mit den Erkenntnissen aus dieser Recherche wird ein Modell erstellt, welches die zwei verschiedenen Abfallbehandlungsstrategien darstellt und vergleicht. Die Ergebnisse aus dem Vergleich werden dann einer Sensitivitätsanalyse unterzogen um die Einflüsse der verschiedenen Parameter zu erkennen. Dieser Schritt wird mit weiteren Eingabeparametern wiederholt und dann mit den Ergebnissen aus dem ersten Vergleich gegenübergestellt. Im nächsten Abschnitt der Arbeit wird eine Wirtschaftlichkeitsbetrachtung des Anwendungsfalles zwei, also dem Anlagenlayout mit Fermentations- und Verbrennungsanlage, gemacht. In dieser Betrachtung werden die Investitionskosten, die jährlichen Kosten und die jährlichen Gewinne der Fermentationsanlage analysiert und schließlich in einer Amortisationsrechnung dargestellt. Die eingesetzten Parameter für die Kosten und Gewinne werden dabei wiederum variiert und in einer Sensitivitätsanalyse analysiert. Zum Abschluss wird die Forschungsfrage der Masterarbeit beantwortet und ein Ausblick für Anlagen mit kombinierter Fermentations- und Verbrennungsanlage gemacht. KW - Waste KW - Energetic Comparison KW - Economic Comparison KW - Incineration KW - Fermentation Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2767 ER - TY - THES A1 - Schatzmann, Kilian T1 - Datenbasierte Analyse der Beleuchtungsinfrastruktur T1 - Data-driven modelling for the lighting industry N2 - In Europa und den USA werden rund 39 % des Energieverbrauchs durch den Betrieb von Gebäuden verursacht. Sie bieten somit großes Potential, den Gesamtenergieverbrauch zu verringern. Eine sinnvolle Möglichkeit dieser Umsetzung, ohne auf Gebäudekomfort verzichten zu müssen, liegt in der Optimierung der Gebäudeeffizienz. Dahingehend werden physikalische und datenbasierte Modelle als Planungstool für die Gebäudemodellierung verwendet, um frühzeitig Erkenntnisse über deren Energieverbrauch zu gewinnen. Während physikalische Modelle thermodynamische Prinzipien zur Modellierung des Energieverbrauchs einsetzen, verwenden datenbasierte Modelle historische oder allgemein verfügbare Daten, um ein Vorhersagemodell zu entwickeln. Das Ziel dieser Arbeit ist die Erstellung eines datenbasierten Modells, zur Prognose des Energieverbrauchs der Beleuchtung von Bürogebäuden. Es wurden bereits zahlreiche Studien hinsichtlich Prognosen des Energieverbrauchs erstellt. Die meisten beziehen sich jedoch auf den Gesamtenergieverbrauch oder jenen, welcher für Heizung, Kühlung oder Klimatechnik aufgewendet wird. Die Recherche des Autors ergab, dass vergleichsweise wenig Forschung für Vorhersagemodelle zur Ermittlung des Energieverbrauchs für die Beleuchtung betrieben wurde. Zur Umsetzung der Analyse stehen dem Autor Daten aus der Beleuchtungsinfrastruktur sowie Wetter-, Zeit- und Gebäudedaten zur Verfügung. Anhand dieser Arbeit soll eruiert werden, ob diese Daten hinreichend aussagekräftig sind, um ein geeignetes Modell zu entwickeln. N2 - In Europe and USA, 39 % of the energy consumption is caused from buildings and this is why buildings offer great potential to decrease the overall energy consumption. One way to drive lower energy demand, without reducing comfort, can be achieved by improving the efficiency of buildings. Physical and data-driven modelling to predict the energy consumption has received a lot of attention the last years. Predicting the energy consumption is valuable for enhanced decision making in an early stage of building design. While physical models are based on thermodynamics principles, data-driven models are using historical or general data to predict the energy consumption. The aim of this work is to create a data-driven model to predict the energy consumption of lighting from office buildings. A lot of research has been carried out to predict the energy consumption of buildings. Nevertheless the most of this research belongs to the energy consumption of heating, ventilation and air conditioning (HVAC) or the whole building. Based on the research for this academic writing only little research were done to predict the energy consumption for lighting. For the implementation of this work the author is going to use data from a lighting controls system as well weather-, time- and general building information to create a data-driven model to predict the lighting based energy consumption. KW - Data Science KW - Machine Learning KW - Energieverbrauch KW - Prognose KW - Beleuchtung Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2771 ER - TY - THES A1 - Eder, Elias T1 - Konzeption und Aufbau eines Blasensäulenbefeuchters zur Analyse der Befeuchtung von Luft in Flüssigkeitssäulen T1 - Conception and construction of a bubble column humidifier for the analysis of the humidification process of air in liquid columns N2 - Der Befeuchtungs-Entfeuchtungs-Prozess (HDH) wird zur Meerwasserentsalzung eingesetzt und bietet Vorteile wie die Nutzung von Wärme auf einem geringen Temperaturniveau sowie die Realisierbarkeit dezentraler Anlagen. Bei diesem Prozess wird Luft im Kontakt mit warmem Salzwasser im Optimalfall bis zur Sättigung befeuchtet. Die feuchte Luft wird anschließend abgekühlt, um das in ihr befindliche Wasser wieder zu kondensieren. Obwohl der HDH-Prozess bereits mehrfach Gegenstand der Forschung war, besitzt die Effizienz des Prozesses nach wie vor ein hohes Steigerungspotential. Das Ziel dieser Masterarbeit besteht in der Konzeption und der Realisierung eines Versuchsaufbaus zur Analyse der Befeuchtung von Luft in Wasser. Dabei soll der Untersuchungsgegenstand zukünftiger Versuche die Befeuchtereinheit sein, die ein hohes Potential hinsichtlich der Effizienzsteigerung von HDH-Systemen bietet. In neueren Publikationen wurden zum Einsatz in HDH-Systemen Blasensäulenbefeuchter als eine bessere Alternative zu Festbettbefeuchtern oder Sprühtürmen vorgeschlagen, weswegen die Befeuchtung in solchen Aggregaten näher untersucht werden muss. Das Hauptziel dieser Masterarbeit ist ein Versuchsaufbau, der die Möglichkeit bietet, die Parameter, die die Befeuchtung von Luft in einer Blasensäule maßgeblich beeinflussen, mit einer ausreichenden Genauigkeit zu messen, um aus diesen Messungen semiempirische Korrelationen ableiten zu können. Die die Befeuchtung von Luft maßgeblich beeinflussenden Parameter sind die Wassertemperatur, der Füllstand im Befeuchter, die Luftgeschwindigkeit sowie die Blasengröße. Zum aktuellen Stand ist ein HDH-System, bestehend aus einem Blasensäulenbefeuchter, einem Querstromwärmetauscher sowie einer Dosierpumpe errichtet. Mit diesem System können wissenschaftlich notwendige empirische Zusammenhänge zwischen den die Befeuchtung beeinflussenden Parametern und der Befeuchtung von Luft aus Versuchen abgeleitet werden. Die im Versuchsaufbau verbaute Messtechnik wurde derart ausgewählt, dass deren Einfluss auf das System so gering wie möglich gehalten werden kann. Mit dem Versuchsaufbau ist es darüber hinaus möglich, invasive Messmethoden mit nicht invasiven Messmethoden direkt zu vergleichen. Um eine für die Messungen optimale Befeuchtergeometrie zu finden, sind zwei Blasensäulenbefeuchtereinheiten aufgebaut, davon eine mit planarem und eine mit zylindrischem Querschnitt. So ist es möglich, im Direktvergleich die Vor- und Nachteile der Querschnittsanordnungen nachzuweisen. Die Komponenten der beiden HDH-Systeme wurden anhand von wissenschaftlich akzeptierten Modellen bezüglich der dazugehörigen Wärmeübertragungsraten, der Wärmeverluste und der Druckverluste ausgelegt. Eine Modellierung des Stoffübergangs in der Blasensäule ist durchgeführt. Anhand dieser Modellierung konnte der Stoffübergangskoeffizient in der Grenzschicht zwischen Luftblase und Flüssigkeitssäule ermittelt werden. Anhand einer Massenbilanz konnte über den Stoffübergangskoeffizienten die Austrittswasserbeladung der feuchten Luft modelliert werden. Die Funktionalität des Versuchsaufbaus ist gegeben. Messungen des Gasgehalts zeigen eine sehr gute Übereinstimmung mit wissenschaftlich anerkannten Korrelationen zum Gasgehalt. Die optische Zugänglichkeit des Versuchsaufbaus ist evaluiert und lässt die Tendenz ableiten, dass sich ein planarer Befeuchterquerschnitt in Verbindung mit Fotoaufnahmen von den durchgeführten Varianten am besten zur digitalen Bildanalyse eignet. Aus den Experimenten, die am realisierten Versuchsaufbau durchgeführt werden, kann sich eine allgemeingültige Auslegungsgrundlage für Versuchsaufbauten ergeben, mit denen Messungen der Befeuchtung von Luft in Blasensäulenbefeuchtern durchgeführt werden sollen. N2 - The humidification-dehumidification-process (HDH) is used for water desalination since it can use low-temperature energy and can be used to implement small-scale desalination systems. In this process, air is humidified with contact to a warm water surface, at best to a saturated state, and then transported to a dehumidification unit, where it is cooled in order to condense water out of the humid air. Despite the so far extensive investigation of the HDH process, the efficiency of this process still has a large potential for improvement. The goal of this master's thesis is to develop a concept for the construction of an HDH-system for the analysis of the humidification process of air in a bubble column of water and also to construct such an HDH-system. The planned measurements focus on the humidification part of the HDH-process, due to the fact, that not a lot of research has been made on this topic. Recent publications indicate that bubble column humidifiers could provide a better solution for the humidification process in HDH-systems than packed bed or spray tower humidifiers. The main goal of this thesis is the construction of an HDH-system that enables accurate measurements of the main parameters that influence the humidification of air in a bubble column, such as water temperature, liquid height, air velocity and bubble size. To this end, a setup consisting of a bubble column humidifier, a fin-and-tube heat exchanger and a dosage pump for water is constructed. With the constructed setup it is possible to measure the temperature and height of the water in the bubble column, the size of the bubbles formed and the velocity of the inlet air stream and thereby quantify their influence on the humidification process. This then allows for the deduction of empirical correlations that can be used to optimize the HDH-system. The sensors and actuators used in the setup have been carefully chosen to minimize their interference with the system. The setup also allows for a direct comparison between measurements made by invasive and non-invasive sensors. In order to identify the geometry better suited to these measurements, bubble columns with a rectangular and a circular cross section are constructed. In the designing process of the setup, valid models have been used in order to get good estimations of the important heat losses, heat rates and pressure drops regarding the system components. A mass transfer model of the bubble column humidifier has been created. Using this model the mass transfer coefficient in the liquid-gas interface has been evaluated. By applying a mass balance using the mass transfer coefficient the absolute outlet humidity can be displayed with dependence on the liquid height. Functionality of the constructed setup is given. Measurements of gas holdup are carried out and agree well with previously reported correlations. Optical access of the setup is evaluated and indicates, that a humidifier with a planar cross section in combination with photographs are best suited for digital image analysis. Measurements and experiments on the built setup can result in a good basis for the design and construction of a system to investigate a bubble-column humidifier. KW - HDH-Prozess KW - Blasensäule KW - Wasseraufbereitung KW - Meerwasserentsalzung KW - Digitale Bildanalyse Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2766 ER - TY - THES A1 - Rogen, Mario T1 - Analyse der Stromverbräuche in einem Krankenhaus T1 - Analysis of Electricity Consumptions in a Hospital BT - Strategische Identifizierung der Verursacher mithilfe verschiedener Methoden N2 - Obwohl der Energiebedarf eines Krankenhauses nur ca. 1,2% der Gesamtkosten ausmacht, werden Energieeinsparmaßnahmen und -optimierungen immer wichtiger. Neben dem steigenden Umweltbewusstsein wird auch der Kostendruck in diesem Dienstleistungssektor immer größer. Trotz der in vielen Krankenhäusern vorhandenen und gut ausgebauten Gebäudeleittechnik fehlt oft das Detailwissen über den Energieverbrauch und deren Verursacher. Aufgrund der großen Anzahl an verwendeten Geräten und Kleinverbrauchern sowie der vielen gebäudetechnischen Großgeräte ist eine genaue Ursachensuche kein leichtes Unterfangen. Auch im Krankenhaus Feldkirch sind eine Vielzahl automatischer Stromzähler installiert und im Energiemonitoringsystem aufgeschaltet. Dennoch ist aktuell nur der Gesamtstromverbrauch bekannt und verwertbar. Analysen auf Gebäude oder Anlagen-Ebene werden nur sehr wenige durchgeführt. In dieser Arbeit soll untersucht werden, wie die wesentlichen Einflussfaktoren auf den Stromverbrauch mithilfe der installierten automatischen Zähler identifiziert werden können. Um herauszufinden, mit welchen Methoden der größte Informationsgehalt gewonnen werden kann, kommen verschiedene Methoden wie Kennzahlenvergleiche, die Darstellung als Sankey-Diagramm, objektspezifische Vergleiche und statistische Analysen sowie Energieganganalysen zur Anwendung. Die erarbeiteten Auswertungen und Darstellungen zeigen sehr schnell, dass ohne eine Vielzahl an Subzählern keine sinnvollen Analysen möglich sind. Die große Anzahl an angeschlossenen Verbrauchern und deren variables Regelverhalten lassen aus den Daten (z. B. Summenzählern) anhand zusammengefasster Stromverläufe kaum Schlüsse für einzelne Gebäude zu. Es zeigt sich auch, dass eine einzelne Darstellungsform für alle Auswertungen keinen Sinn macht. In dieser Arbeit werden mögliche Einbauorte für die Stromzähler vorgeschlagen sowie Verfahren für eine durchdachte Auswertung der Energieverbräuche und Umsetzung in die Praxis angeführt. N2 - Despite the low amount of energy costs in a hospital at 1.2% of overall spendings, energy saving measures and -optimization get increasingly more important. In addition to growing environmental awareness, cost pressure in the public health sector is also rising. Although well-developed building services management system is installed in many hospitals, there is often a lack of detailed knowledge about energy consumption and its causes. Due to the large number of devices used as well as the many large building services plants, it is very hard to find out where the high usage originates from. The hospital in Feldkirch has installed a large number of automatic electricity meters and connected them to the energy monitoring system. Nevertheless, only the overall power consumption is known and evaluable at the moment. Reports at building- or plant level are rarely performed. The aim of this thesis is to investigate how the most significant factors influencing power consumption can be identified by using the installed automatic meters. For this purpose, various methods such as comparison of key figures, graphical display in Sankey diagrams object-specific comparison, statistical evaluation, as well as energy profile reports are carried out to find out which methods can be used to obtain the greatest amount of information. The developed evaluations and presentations show immediately that no meaningful analyses are possible without numerous submeters. The large number of connected appliances and their variable control behaviour hardly allow conclusions to be drawn on the basis of summarized metering of, for example, individual buildings. This also shows that a single form of presentation for all evaluations doesn’t make any sense. Within this thesis, places for the installation of the submeters are suggested and the procedures for an elaborated evaluation of energy consumption are specified and implemented in practice. KW - Krankenhaus KW - Stromverbrauch KW - Sankey-Diagramm KW - Kennzahlen KW - NILM Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2770 ER - TY - THES A1 - Fresacher, Angelika T1 - Methode zur Lastverschiebung von elektrischen Warmwasserspeichern durch die Nutzung intelligenter Stromzähler T1 - Load shifting method for domestic hot water heaters using smart electricity meters N2 - Durch den vermehrten Ausbau dezentraler Energieerzeugungsanlagen gewinnt verbraucherseitiges Lastmanagement für die Netzbetreiber immer mehr an Bedeutung. Neue Möglichkeiten zur Laststeuerung bei Haushalten ergeben sich durch den Einsatz von intelligenten Stromzählern, sogenannten Smart Metern, da sie über eine Kommunikationsschnittstelle mit fernparametrierbarem Schaltrelais verfügen und den Stromverbrauch im Viertelstundenraster aufzeichnen können. Diese Masterarbeit untersucht eine Methode, mit der Lastverschiebungsmaßnahmen bei elektrischen Warmwasserspeichern durchgeführt werden können. Die Lastverschiebung wird lediglich durch die Funktionalitäten eines Smart Meter bewerkstelligt. Dabei ist das Ziel, eine Lastverschiebungsmethode zu finden, die vom Netzbetreiber simpel implementiert werden kann und mindestens den gleichen Komfortansprüchen genügt, die eine traditionelle Nachttarifschaltung aufweist. Die Schwierigkeit liegt hierbei in der Einschränkung, dass der Netzbetreiber vom Stromverbrauch der Speicher auf den Warmwasserbedarf der Kunden schließen muss. Mit Hilfe eines thermodynamischen Modells werden verschiedene Lastverschiebungsszenarien bei mehreren Haushalten angewendet. Über die Simulation des Temperaturverlaufs wird ferner auf die Qualität der Warmwasserbereitung geschlossen und mit jener der klassischen Nachttarifsteuerung verglichen. Liegt die Temperatur häufiger unter einem bestimmten Mindestniveau als jene bei der Nachttarifschaltung, gilt die Qualität als nicht ausreichend. Die Ergebnisse der Untersuchung zeigen, dass mit der vorgestellten Methode für jeden Haushalt eine Lastverschiebung gefunden werden kann, die für den Netzbetreiber Vorteile bringt und die Mindestanforderungen an den Kundenkomfort erfüllt oder teilweise sogar verbessert. Es konnte festgestellt werden, dass mit der vorgestellten Methode der Großteil der Heizenergie (mindestens 60% bei allen Haushalten) in der ersten Tageshälfte zur Verfügung gestellt werden muss. Zusätzlich ergeben sich Energieeinsparungen, da die Beheizung des Speichers und der Warmwasserbedarf besser aufeinander abgestimmt werden. Mit der gezeigten Methode könnten Lastverschiebungsmaßnahmen schnell und einfach vom Netzbetreiber eingeführt werden, jedoch gilt es davor Einschränkungen wie die Legionellen-Problematik und Kundenkommunikation oder -akzeptanz zu klären. N2 - With decentralised power generation being steadily on the rise, the need for load shifting measures is increasing as well. A new possibility for efficient and intelligent demand side management (DSM) is offered through the use smart electricity meters. These meters provide a two-way communication interface with a configurable switching relay and measure energy consumption with 15-minute frequency, which creates new opportunities of DSM for grid operators. This master thesis studies a method using smart meters to deploy load shifting on domestic hot water heaters (DHWH). This approach focuses on the goal of providing a load shifting scenario that can easily and quickly be implemented by grid operators and nevertheless meets the requirements of water heating in the same way as a night rate controlled DHWH would. One major restriction is the fact that a grid operator has no information about the costumer's hot water demand. The only way to estimate the hot water demand is through studying the electricity demand of the DHWH. As the basis of the method, a simple iterative simulation of a thermodynamic model is applied where the temperature profiles of different load shifting strategies are analysed. Furthermore, the temperature profile of the load shifting approach is compared to the profile of the night rate controlled DHWH. The load shifting measures are successful if the temperature levels with DSM are less likely to undercut a certain minimum than the ones of the night rate controlled DHWH. It appeared that for each one of the studied households a successful load shifting strategy can be found. In addition, the simulation has shown that, using the suggested method, most of the water heating energy has to be provided in the first part of the day (at least 60% of the total daily power demand). What is more, energy savings can be generated by aligning the heating power more closely with the hot water demand. In conclusion it can be stated that with the suggested method it is possible for grid operators to simply implement successful load shifting measures. However, crucial restrictions to its applicability like hygienic conditions or customer acceptance have to be solved first. KW - Demand Side Management KW - Smart Meter KW - Warmwasserspeicher Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2768 ER - TY - THES A1 - Jona, Sven T1 - Comparative LCA of storage concepts for full electric car ferries in Norway T1 - Vergleichende Ökobilanz von Speicherstystemen für vollelektrische Autofähren in Norwegen N2 - In times of global climate change, it is increasingly important to investigate emissions and resource consumption of all machines and, if possible, to improve them. This includes within the transport sector car ferries. In order to reduce the environmental impacts of car ferries, the electrification has penetrated into this sector, which has led to the world's first fully electric car ferry. One of the most important components to operate this ferry is the energy storage. Not only the battery storage of the ferry itself is needed, but also an onshore battery storage system is needed to support the electrical grid. The present study examines how storage technologies and concepts can impact the environment considering the world's first all-electric car ferry, MF Ampere, which operates in Norway. To examine this, the current onshore battery storage system is compared to a concrete sphere storage system. For this purpose, data from the first test run of this new storage technology, which was successfully carried out by the Fraunhofer Institute in 2016, is considered. Subsequently, a life cycle assessment of the two storage systems is carried out to compare the environmental impacts. The concrete sphere storage system performs better for 15 of 17 impact categories compared to the existing onshore battery storage system. Depending on the impact category the impact reduction is about 2% to 8%. Nevertheless, it is difficult to estimate how long the useful life and how good the efficiency of the concrete ball storage will be, since no system of this size has been tested yet. Also, the costs of the concrete sphere storage system have not been considered. N2 - In Zeiten des globalen Klimawandels wird es immer wichtiger, die Emissionen und den Ressourcenverbrauch aller Maschinen zu untersuchen und, wenn möglich, zu verbessern. Dazu gehören auch Autofähren innerhalb des Transportsektors. Um die Umweltbelastung durch Autofähren zu reduzieren, ist die Elektrifizierung auch in diesen Sektor vorgedrungen. Dies hat zur weltweit ersten vollelektrischen Autofähre geführt. Eine der wichtigsten Komponenten, um diese Fähren zu betreiben, ist der Energiespeicher. Nicht nur der Batteriespeicher der Fähre selbst wird benötigt, sondern auch ein Batteriespeichersystem, das an Land installiert ist und zur Unterstützung des Stromnetzes gebraucht wird. Die vorliegende Arbeit untersucht, wie sich Speichertechnologien und -konzepte auf die Umwelt auswirken können, wenn man die in Norwegen operierende erste vollelektrische Autofähre der Welt, MF Ampere, betrachtet. Um dies zu untersuchen, wird das aktuelle Land-Batteriespeichersystem mit einem Betonkugelspeichersystem verglichen. Zu diesem Zweck werden Daten aus dem ersten Testlauf des Betonkugelspeichersystems berücksichtigt, der 2016 vom Fraunhofer-Institut erfolgreich durchgeführt wurde. Anschließend wird eine Ökobilanz der beiden Speichersysteme durchgeführt, um die Umweltauswirkungen zu vergleichen. Das Ergebnis dieser Ökobilanz ist, dass das Betonkugelspeichersystem für 15 von 17 Wirkungskategorien besser als das vorhandene Land-Batteriespeichersystem ist. Abhängig von der Wirkungskategorie beträgt die Reduzierung der Auswirkungen etwa 2% bis 8%. Dies ist größtenteils auf den Ressourcenverbrauch in der Bauphase der beiden Systeme zurückzuführen, da die Ressourcen für die Batterien deutlich Umweltschädlicher sind. Es ist jedoch schwierig die Nutzungsdauer und die Effizienz des Betonkugelspeichers abzuschätzen, da noch kein System dieser Größe getestet wurde. Auch die Kosten für das Betonkugelspeichersystem wurden nicht berücksichtigt. KW - car ferry KW - storage system KW - concrete sphere KW - life cycle assessment Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2772 ER - TY - THES A1 - Bischof, Thomas T1 - Modellbasierte Prüfung von Stromwandlern T1 - Model-based testing of current transformer N2 - Damit eine möglichst ausfallsichere Energieversorgung und Energieübertragung gewährleistet werden kann, werden verschiedene Betriebsmittel benötigt. Diese Betriebsmittel müssen gewisse Genauigkeitsgrenzwerte einhalten. In dieser Masterarbeit wird die Prüfung der Genauigkeit von Stromwandlern diskutiert. Die Ermittlung der Genauigkeit kann durch das Einspeisen eines Primärnennstroms (einige kA) und eine Messung des Sekundärstroms erfolgen. Daraus wird der Übertragungsfehler bestimmt. Die Genauigkeit wird unter anderem durch den Übertragungsfehler beschrieben, welcher sich aus dem Übersetzungsfehler und dem Phasenfehler zusammensetzt. Es wird bei diesem Verfahren von der Primärmethode oder auch Primärstrommethode gesprochen, dies ist die Referenzmessung nach den Normen IEC 61869-2 und IEEE C57.13. Die Firma OMICRON electronics GmbH entwickelte ein modellbasiertes Messverfahren, das den Einsatz eines mobilen und leichten Messgeräts erlaubt. Das Messgerät wird CT Analyzer genannt. Bei Verwendung dieser Methode werden keine hohen Ströme verwendet, was den BenutzerInnen zusätzlich eine höhere Sicherheit für die Bedienung des Geräts bietet. Mit diesem Messverfahren werden die einzelnen Komponenten des elektrischen Ersatzschaltbildes des Transformators bestimmt. Mit den ermittelten Komponenten kann dann der Übertragungsfehler berechnet werden. Das modellbasierte Messverfahren beruht auf Messungen, die von der Sekundärseite des Stromwandlers her durchgeführt werden. Man spricht bei diesem Messverfahren von der Sekundärspannungsmethode, welche inzwischen in der Norm IEC 61869-2 als alternative Messung angeführt ist. Der Vorteil der Primärmethode ist die Hoch-Präzisionsmessung, da die Prüfung unter realen Bedingungen und mit einer direkten Messung durchgeführt wird. Die Genauigkeit dieser Methode wird durch die Messtechnik selbst bestimmt, sie ist sehr genau und daher als Referenz gültig. Das Ziel der Sekundärspannungsmethode ist es, den Vorteil der Hoch- Präzisionsmessung für die Sekundärspannung zu nützen. Da es sich um ein modellbasiertes Messverfahren handelt, wird die Messgenauigkeit bei diesem Verfahren durch das angewandte Modell bestimmt und nicht durch die Messtechnik wie bei der Primärmethode. Daher sind Untersuchungen am Modell notwendig. Es gibt einige wenige Stromwandlertypen, bei denen es größere nicht akzeptable Differenzen zwischen der Primärmethode und der Sekundärspannungsmethode gibt. Diese Masterarbeit befasst sich deshalb mit Untersuchungen von Möglichkeiten und Grenzen der Sekundärspannungsmethode. Zu Beginn wird eine theoretische Sensitivitätsanalyse mathematisch erarbeitet. In diesem Zusammenhang wird der komplexe Fehlervektor eines Stromwandlers eingeführt. Diese Sensitivitätsanalyse dient der Ermittlung des Einflusses auf den komplexen Fehler in Abhängigkeit von verschiedenen Parametern und zur Auswahl von Stromwandler-Testobjekten. Des Weiteren wird die Sensitivitätsanalyse durch Messungen an verschiedenen Stromwandlern verifiziert. Die Untersuchungen basieren auf MATLAB-Simulationen und Messungen mit dem OMICRON Messgerät CT Analyzer, welches die Sekundärspannungsmethode anwendet. Die Ergebnisse werden mit den Herstellerdaten (Primärmethode) verglichen und analysiert werden. N2 - To ensure a reliable power supply and energy transfer, various assets are required. These assets must comply to certain accuracy limits. This master thesis discusses the testing of the accuracy of current transformers. The determination of the accuracy can be achieved by injecting the nominal primary current (in the range of kA) and then measuring the resulting secondary output current. The accuracy is defined by the transmission error which contains the ratio error and the phase displacement. This procedure is called primary method or primary current method, which is the reference measurement as per IEC 61869-2 and IEEE C57.13 standard. The company OMICRON electronics GmbH developed a model-based method which allows the use of a mobile and light weight measurement device. The device is called CT Analyzer. Utilizing this method, high currents are no longer required for test, which provides the user with a higher safety when operating the device. With this measurement method the individual components of the electrical equivalent circuit diagram of the current transformer are determined. When these individual components are all known, the transmission error can be calculated. The model-based method is based on measurements made from the secondary side of the current transformer. This method is called secondary voltage method and is meanwhile part of the IEC 61869-2 standard as an alternative measurement method. The advantage of the primary method is that it is a high-precision measurement as it is done under real condition and performed as a direct measurement. The accuracy of this method is dependent on the measuring technique itself, which is very accurate and therefore valid as a reference. The aim of the secondary voltage method is to take advantage of the high-precision measurement for the secondary voltage method. The measurement accuracy of the secondary voltage method is dependent from the model itself and not by the measurement technique as for the primary method. Therefore, investigations on the model are necessary. There are few current transformer types with larger unacceptable differences when measuring accuracy between the primary current method and secondary voltage method. This master thesis studies potentialities and limits of the secondary voltage method. First a theoretical sensitivity analysis will be mathematically derived. In this context the complex error of a current transformer is introduced. This sensitivity analysis is used to determine the influence on the complex error depending on different parameters and for selecting current transformer test objects. Furthermore, the derived sensitivity is verified by different current transformer measurements. The investigations are based on MATLAB simulations and measurements with the OMICRON CT Analyzer using the secondary voltage method. The results are compared and analyzed with the manufacturer data (primary method). KW - Stromwandler KW - Sekundärspannungsmethode KW - Stromwandlerprüfung KW - Stromwandlergenauigkeit Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2775 ER - TY - THES A1 - Reitmair, Florian T1 - Dimensionierung von Tankstellen an der A96 bei vollständiger Elektrifizierung des derzeitigen deutschen PKW-Straßenverkehrs T1 - Siting and sizing of charging stations along the A96 Autobahn assuming complete electrification of current German passenger fleet N2 - Das Ziel der Masterarbeit ist es, ausgewählte Tankstellen an der A96 unter Voraussetzung einer vollständigen Elektrifizierung des deutschen PKW-Straßenverkehrs analog des heutigen Tankverhaltens zu dimensionieren. Zu Beginn der Masterarbeit wird die elektrische Leistung berechnet, welche die deutschen PKW bei vollständiger Elektrifizierung des deutschen PKW-Straßenverkehrs benötigen werden. Um das Ergebnis auf Plausibilität überprüfen zu können, wird die Berechnung mit zwei verschiedenen Ansätzen vollzogen. Einerseits werden als Grundlage durchschnittliche Jahresfahrstrecken der Autofahrer/-innen verwendet und andererseits wird über den Primärenergiebedarf, den Fahrzeugbestand und den Wirkungsgraden von Ottomotoren und Elektromotoren die zu bestimmende Leistung berechnet. Öffentliche Daten aus Verkehrszählungen sollen im weiteren Verlauf der Masterarbeit ausgewertet werden. Unter anderem erfolgt mit diesen Werten eine Modellbildung des Verkehrs, um den Verkehrsfluss mathematisch darzustellen und zu simulieren. Die Durchführung einer Live-Messung an der Tankstelle Lechwiesen Nord sowie die nachträglich erlangten Daten zum tatsächlich stattgefundenen Verkehrsaufkommen sind für die Auswertung des in AnyLogic hinterlegtem mathematischen Modells essentiell. Auch für die Frage nach den zu tankenden Autos eines bekannten Verkehrsaufkommens sind diese hilfreich. Zur Bestimmung der Anzahl von Elektrozapfsäulen erfolgt eine iterative Annäherung an die Kurve des Tankverhaltens von Diesel- und Benzinautos. Als abschließendes Ergebnis werden für die Tankstelle Lechwiesen Nord und Lechwiesen Süd jeweils 20 Elektrozapfsäulen gefunden. Für den Autohof Aichstetten ergeben sich unter Berücksichtigung des Verkehrsaufkommens 27 zu installierende Elektrozapfsäulen, sodass ein identisches Tankverhalten von Elektroautos bei vollständiger Elektrifizierung des deutschen PKW-Straßenverkehrs angenommen werden kann. N2 - Siting and sizing of charging stations along the A96 Autobahn assuming complete electrification of current German passenger fleet. The aim of the master thesis is designing filling stations along the A96 Autobahn. It is assumed that the current German passenger fleet has been electrified. In the beginning of this master thesis electrical power consumed by electrified passenger car road traffic is calculated. The plausibility of the results can be verified by two estimation approaches. First the electrical power is to be calculated based on the average driving distance of German drivers, second the electrical power has to be calculated based on primary energy consumption, vehicle stock and efficiencies of combustion engines and electric motors. Furthermore public traffic census data are examined to create a mathematical model and simulate different traffic flows. Live measurement at filling station Lechwiesen Nord and receiving the actual traffic volume data for that day will be useful for evaluating AnyLogic's mathematical model. Moreover the question regarding refuelling cars depending on the traffic flow can be solved. For determining the number of charging stations an iterative approach has to be used. As a final result 20 electrical charging stations have to be installed each for Lechwiesen Nord and Lechwiesen Süd. At rest area Autohof Aichstetten 27 electrical charging stations have to be considered, so that a nearly similar refilling behaviour of electric and combustion engine cars can be assumed. KW - Tankstelle KW - Elektroauto KW - Elektrifizierung KW - A96 KW - Lechwiesen Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2773 ER - TY - THES A1 - Patzwahl, Hans-Jörg T1 - Optimiertes Auswahlverfahren von Hochstromwandlern für Schutzzwecke T1 - Optimized selection process of current transformers N2 - Die nachfolgende Arbeit befasst sich mit Hochstromwandlern für Schutzzwecke. Laut Aussage von Paul Scherrer finden sich diese in jedem Verteilnetz und tragen einen erheblichen Teil zur Sicherheit des Netzes bei. Im ersten Teil der Arbeit wird beschrieben, wie man bei der Dimensionierung bzw. der Auswahl eines Hochstromwandlers für Schutzzwecke vorgeht und welche technischen Parameter dafür notwendig sind. Der zweite Teil der Arbeit befasst sich damit, wie man die Auswahl sowohl wirtschaftlich als auch technisch im Bezug auf fiktive Zukunftsszenarien optimieren kann. Dafür liegen aktuelle Netzdaten der Energienetze Vorarlberg GmbH vor, welche für diese Arbeit anonymisiert wurden. Die fiktiven Zukunftsdaten sind Annahmen. Für den Prozess der Optimierung wurde ein Tool in Python angefertigt, welches eine optimierte Auswahl von Hochstromwandler für Schutzzwecke durchführt und diesen Prozess erleichtern soll. Dieses wird nach eigener Einschätzungen keine Verwendung in der Praxis finden, da es nur relevant sein wird, wenn man ein Stromnetz wie wir es heute in größeren Städten und Gemeinden finden, von null an neu aufbauen möchte. N2 - The following master thesis deals with high current transformers for protection purposes. These transformers can be found in every power grid and make a considerable contribution for the network safety. The first part of the thesis describes how to proceed with the dimensioning or selection of a high current transformer for protection purposes and which technical parameters are important for it. The second part of the theses deals with the optimization of the dimensioning. The Selection of the high current transformers will be optimized for the economic and the technical affect. In the process, current data is compared with future scenarios. For this process, a tool was created in Python, which makes is possible to optimize the selection of high current transformers for protection purposes and to facilitate the process. According to our own estimates, this will not find any use in practice, as it will only be relevant if you want to rebuild a power grid as we know it today in larger cities and municipalities from scratch. KW - Hochstromwandler KW - Dimensionierung KW - Auswahlverfahren KW - Lineare Optimierung KW - Python Y1 - 2018 U6 - http://dx.doi.org/10.25924/opus-2774 ER - TY - THES A1 - Kepplinger, Peter T1 - Autonomous demand side management of domestic hot water heaters N2 - Load shifting of resistive domestic hot water heaters has been done in Europe since the 1930s, primarily to ease the power supply during peak times. However, the pursued and already commenced energy transition in Europe changes the requirements for the underlying logic. In this more general context, demand side management is considered a viable approach to utilize the flexibility of thermal and electrochemical storage systems for buffering energy generated from renewables. In this work, an autonomous approach for demand side management of energy storage systems is developed, which is based on unidirectional communication of an incentive. This concept is then applied to the specific problem of resistive domestic hot water heaters. The basic algorithms for an optimized operation are developed and evaluated based on simulation studies. The optimization problem considered, maps the search for the optimal heating schedule, while ensuring the temperature limits defined: Firstly, a maximum, which is defined by the hysteresis set point temperature; Secondly, during hot water draw offs, the outlet temperature should not fall below a set minimum. To establish this, the time series of hot water usage has to be predicted. Depending on the complexity of the hot water heater model used, the formulation of the problem ranges from a linear to non-linear optimization with discontinuous constraints. The simulation studies presented, comprise a formulation as binary linear optimization problem, as well as a solution based on a heuristic direct method to solve the non-linear version. In contrast to the first linear approach, the latter takes stratification inside the tank into account. One-year simulations based on realistic hot water draw profiles are used to investigate the potentials with respect to load shift and energy efficiency improvements. Additional to assuming perfect prediction of user behavior, this work also considers the k-nearest neighbors algorithm to predict the time series. If compared to usual night-tariff switched operation, assuming perfect prediction shows 30 % savings on the electricity market when stratification is taken into account. The user prediction proposed leads to 16 % cost savings, while 6 % of the electric energy is conserved. Based on the linear approach, a prototype is developed and used in a field test. A micro computer processes the sensor information for local data acquisition, receives electricity spot market prices up to 34 hours in advance, solves the optimization problem for this time horizon, and switches the power supply of the resistive heating element accordingly. Beside the temperature of the environment, the inlet and outlet temperatures, the temperature inside the tank is measured at five points, as well as the water volume flow rate and the electric power recorded. Two test runs of 18 days each, compare the night-tariff switched operation to the price-based optimization in a real-world environment. Results show a significant increase of 6 % in thermal efficiency during the operation based on the algorithm developed, which can be contributed to the optimization accounting for the usage expected. To facilitate the technical and economic feasibility for retrofit-able implementations of the method proposed for autonomous demand side management, the sensors used must be kept to a minimum. A sufficiently accurate state estimation of the storage has to be achieved, to facilitate a useful model predictive control. Therefore, the last part of this work focuses on the aspect of automated system identification and state estimation of resistive domestic hot water heaters. To that end, real hot water usage profiles and schedules gathered in a field test are used in a lab setup, to collect data on the temperature distribution inside the tank during realistic operating conditions. Four different thermal models, common in literature, are considered for state estimation and system identification. Based on the data collected in the lab, they are evaluated with respect to robustness, computational costs, and estimation accuracy. Based on the observations made in the experiments, an extension of the one-node model by a single additional parameter is proposed. By this adaption, a linear temperature distribution in the lower part of the tank can be modeled during heating. The resulting model exhibits improved robustness and lower computational costs, when compared to the original model. At the same time, the average temperature in the storage tank is estimated nearly as accurate (6 % mean average percentage error) as in the case of the about 50 times more computationally expensive multi-layer model (4 % mean average percentage error). KW - Demand Side Management KW - Hot Water Heater Y1 - 2018 N1 - Jahr der Abschlussprüfung: 2019 ER - TY - RPRT A1 - Wilms, Falko E. P. T1 - Machen Sie doch was Sie wollen T3 - Arbeitsberichte des Competence Center of Communication & Collaboration - 3 Y1 - 2017 ER - TY - BOOK A1 - Wilms, Falko E. P. T1 - Kommunikation in der Theorie sozialer Systeme T3 - Wandel und Kontinuität, 18 Y1 - 2017 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - JOUR A1 - Martin-Sanchez, Javier A1 - Trotta, Rinaldo A1 - Mariscal, Antonio A1 - Serna, Rosalía A1 - Piredda, Giovanni A1 - Stroj, Sandra A1 - Edlinger, Johannes A1 - Schimpf, Christian A1 - Aberl, Johannes A1 - Lettner, Thomas A1 - Wildmann, Johannes A1 - Huiying Huang, A1 - Yuan, Xueyong A1 - Ziss, Dorian A1 - Stangl, Julian A1 - Rastelli, Armando T1 - Strain-tuning of the optical properties of semiconductor nanomaterials by integration onto piezoelectric actuators JF - Semiconductor Science and Technology Y1 - 2017 U6 - http://dx.doi.org/10.1088/1361-6641/aa9b53 SN - 0268-1242 N1 - Veröffentlichungsdatum Web: 6. Dezember 2017 VL - 33. Jg. IS - H. 1 / 013001 ER - TY - JOUR A1 - Voyer, Joel A1 - Ausserer, Florian A1 - Klien, Stefan A1 - Ristow, Anke A1 - Velkavrh, Igor A1 - Diem, Alexander A1 - Zehetner, Johann A1 - Stroj, Sandra A1 - Heidegger, Stefan A1 - Bertschler, Christian A1 - Edlinger, Johannes T1 - Sub-micro laser modifications of tribological surfaces JF - Materials Performance and Characterization Y1 - 2017 U6 - http://dx.doi.org/10.1520/MPC20160015 SN - 2165-3992 VL - 6. Jg. IS - H. 2 SP - 42 EP - 67 ER - TY - CHAP A1 - Seyringer, Dana A1 - Lampert, Peter T1 - Development of e-learning platform in photonics T2 - Educating for Change. The European Conference on Education. The European Conference on Language Learning. June 30 – July 2, 2017. The Jurys Inn Brighton Waterfront, Brighton, UK. ECE, ECLL 2017 Y1 - 2017 PB - International Academic Forum (IAFOR) CY - Nagoya ER - TY - JOUR A1 - Martin-Sanchez, Javier A1 - Trotta, Rinaldo A1 - Mariscal, Antonio A1 - Serna, Rosalia A1 - Piredda, Giovanni A1 - Stroj, Sandra A1 - Edlinger, Johannes A1 - Schimpf, Christian A1 - Aberl, Johannes A1 - Lettner, Thomas A1 - Wildmann, Johannes A1 - Huiying, Huang A1 - Yuan, Xueyong A1 - Ziss, Dorian A1 - Stangl, Julian A1 - Rastelli, Armando T1 - Strain-tuning of the optical properties of semiconductor nanomaterials by integration onto piezoelectric actuators JF - Semiconductor Science and Technology. Veröffentlichungsdatum Web: 6. Dezember 2017 Y1 - 2017 U6 - http://dx.doi.org/10.1088/1361-6641/aa9b53 SN - 0268-1242 VL - 33. Jg. IS - H. 1/013001, 39 S ER - TY - CHAP A1 - Gajdosova, Lenka A1 - Seyringer, Dana ED - Garcia-Blanco, Sonia M. ED - Conti, Gualtiero Nunzi T1 - Simulation of 20-channel, 50-GHz, Si3N4-based arrayed waveguide grating applying three different photonics tools T2 - Integrated Optics. Devices, Materials, and Technologies XXI. 30 January–1 February 2017. San Francisco, California, United States Y1 - 2017 U6 - http://dx.doi.org/10.1117/12.2267817 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Burtscher, Catalina A1 - Kuzma, Anton A1 - Lucki, Michal A1 - Seyringer, Dana ED - Vajda, Jan ED - Jamnicky, Igor T1 - Design and simulation of 1x32 Y-branch splitter applying different photonics tools T2 - Proceedings of the 23rd International Conference on Applied Physics of Condensed Matter (APCOM 2017). June 12 - 14, 2017. Strbske Pleso, Slovak Republic Y1 - 2017 SP - 213 EP - 218 PB - Slovenska Technicka Univerzita CY - Bratislava ER - TY - CHAP A1 - Kriz, Willy Christian ED - Roehl, Heiko ED - Asselmeyer, Herbert T1 - Teamkompetenz als Schlüssel zur Organisationsentwicklung T2 - Organisationen klug gestalten. Das Handbuch für Organisationsentwicklung und Change Management Y1 - 2017 SP - 328 EP - 333 PB - Schäffer-Poeschel CY - Stuttgart ER - TY - CHAP A1 - Pallauf, Martin A1 - Kofler, Manfred A1 - Ates, Nesrin A1 - Förster, Kristina A1 - Hämmerle, Isabella A1 - Piazolo, Felix A1 - Werner, Tobias ED - Kempter, Guido ED - Hämmerle, Isabella T1 - AAL-Lösungen im realen Testumfeld - Evaluationsauszug der Testregion West-AAL T2 - Usability Day XV - Umgebungsunterstütztes Leben T2 - Umgebungsunterstütztes Leben. Beiträge zum Usability Day XV. 22. Juni 2017 Y1 - 2017 SN - 978-3-95853-316-5 SP - 22 EP - 30 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Förster, Kristina A1 - Werner, Tobias A1 - Hämmerle, Isabella A1 - Kofler, Manfred A1 - Ates, Nesrin A1 - Piazolo, Felix A1 - Pallauf, Martin A1 - Fuxreiter, Thomas ED - Kempter, Guido ED - Hämmerle, Isabella T1 - Lessons learned zur Planung und Durchführung von AAL Testregionen T2 - Umgebungsunterstütztes Leben. Beiträge zum Usability Day XV. 22. Juni 2017 Y1 - 2017 SP - 113 EP - 121 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Beyer, Hans-Georg ED - Doerr, Carola ED - Igel, Christian ED - Thiele, Lothar ED - Yao, Xin T1 - Towards a theory of CMA-ES. But first, simplify your CMA-ES! T2 - Theory of Randomized Optimization Heuristics KW - algorithms and complexity KW - evolutionary algorithms KW - machine learning KW - optimization KW - soft computing Y1 - 2017 U6 - http://dx.doi.org/10.4230/DagRep.7.5.22 ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Hartmann, Siegfried A1 - Marxgut, Siegfried A1 - Mathis, Gebhard T1 - Effekte ärztlicher Koordination in Vorarlbergs Pflegeheimen T2 - 6. Österreichischer Interdisziplinärer Palliativkongress. Festspielhaus Bregenz. 27. bis 29. April 2017. Kontroversen in Palliative Care. Abstractband KW - Altenheim KW - Ärztliche Koordination KW - Modellprojekt KW - Palliativarbeit KW - Pflegeheim Y1 - 2017 SP - 16 PB - Österreichische Palliativgesellschaft CY - Bregenz ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Historical roots and new fruits of gaming and simulation JF - Simulation & Gaming Y1 - 2017 U6 - http://dx.doi.org/10.1177/1046878117732845 SN - 1046-8781 VL - 48. Jg. IS - H. 5 SP - 583 EP - 587 ER - TY - CHAP A1 - Kollreider, Gabriel Josef A1 - Weidmann, Karl-Heinz ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Nutzerfreundlichkeit öffentlicher Internetseiten am Beispiel der Länder Tirol und Vorarlberg T2 - Design2product. Beiträge zur empirischen Designforschung. Die Bedeutung empirischer Designforschung für die Praxis T2 - design2product, 7 KW - +AWD 520 D2P KW - +KDC 122 KW - Design : Theorie, Reflexion KW - Fachhochschule Vorarlberg : Design2product Y1 - 2017 SN - 978-3-99018-439-4 SP - 103 EP - 122 PB - Bucher Verlag CY - Hohenems u.a. ET - 1. Auflage ER - TY - BOOK ED - Kempter, Guido ED - Mayer, Horst Otto ED - Weidmann, Karl-Heinz T1 - Design2product. Beiträge zur empirischen Designforschung. Die Bedeutung empirischer Designforschung für die Praxis T3 - design2product, 7 KW - +AWD 520 D2P KW - +KDC 122 KW - Design : Theorie, Reflexion KW - Fachhochschule Vorarlberg : Design2product Y1 - 2017 SN - 978-3-99018-439-4 PB - Bucher Verlag CY - Hohenems u.a. ET - 1. Auflage ER - TY - JOUR A1 - Zehetner, Johann A1 - Vanko, Gabriel A1 - Dzuba, Jaroslav A1 - Lalinsky, Tibor T1 - Femtosecond laser processing of membranes for sensor devices on different bulk materials JF - Advances in Electrical and Electronic Engineering Y1 - 2017 U6 - http://dx.doi.org/10.15598/aeee.v15i3.2033 VL - 15. Jg. IS - H. 3 SP - 561 EP - 568 ER - TY - JOUR A1 - Fredersdorf, Frederic A1 - Moser, Sarah A1 - Mathis, Gebhard T1 - Ärztliche Koordination in Pflegeheimen als ein Baustein menschenwürdiger Palliativarbeit – eine systematische Literaturübersicht JF - Zeitschrift für Palliativmedizin KW - Ärztliche Koordination KW - Pflegeheim KW - Literaturanalyse KW - Status Quo Y1 - 2017 U6 - http://dx.doi.org/10.1055/s-0043-107157 SN - 1615-2921 VL - 18. Jg. IS - H. 5 SP - 255 EP - 261 ER - TY - CHAP A1 - Eberle, Thomas A1 - Kriz, Willy Christian ED - Petrik, Andreas ED - Rappenglück, Stefan T1 - Planspiele in der Hochschullehre und Hochschuldidaktik T2 - Handbuch Planspiele in der politischen Bildung KW - +SEC 572 KW - +SPO 112 KW - Planspiel, Rollenspiel KW - Politische Bildung Y1 - 2017 SN - 978-3-7344-0421-4 SP - 155 EP - 168 PB - Wochenschau Verlag CY - Schwalbach/Ts ER - TY - JOUR A1 - Partel, Stefan A1 - Kasemann, Stephan A1 - Matylitskaya, Volha A1 - Thanner, Christine A1 - Dincer, Can A1 - Urban, Gerald T1 - A simple fabrication process for disposable interdigitated electrode arrays with nanogaps for lab-on-a-chip applications JF - Microelectronic Engineering KW - Cycle-olefin polymer (COP) KW - Electrochemical biosensor KW - Hot embossing KW - Interdigitated electrode array (IDA) KW - Lab-on-a-chip (LOC) Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.mee.2017.03.014 SN - 0167-9317 VL - o.Jg. IS - Bd. 173 SP - 27 EP - 32 ER - TY - CHAP A1 - Burtscher, Catalina A1 - Seyringer, Dana A1 - Lucki, Michal A1 - Kohler, Linda ED - Garcia-Blanco, Sonia M. T1 - New waveguide shape for low loss and high uniformity Y-branch optical splitter T2 - Integrated Optics. Devices, Materials, and Technologies XXI. 30 January–1 February 2017. San Francisco, California, United States Y1 - 2017 U6 - http://dx.doi.org/10.1117/12.2249758 PB - SPIE CY - Bellingham, Wash. ER - TY - JOUR A1 - Matylitskaya, Volha A1 - Kasemann, Stephan A1 - Urban, Gerald A1 - Dincer, Can A1 - Partel, Stefan T1 - Electrochemical characterization of nanogap interdigitated electrode arrays for lab-on-a-chip applications JF - ECS Transactions. Selected Proceedings from the 232nd ECS Meeting. National Harbor, MD – Fall 2017 Y1 - 2017 SN - 1938-6737, 1938-5862 U6 - http://dx.doi.org/10.1149/08010.1295ecst VL - 80. Jg. IS - H. 10 SP - 1295 EP - 1308 ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Burtscher, Catalina ED - Vajda, Jan ED - Jamnicky, Igor T1 - Si3N4 based 40-ch, 50-GHz AWG for medical applications T2 - Proceedings of the 23rd International Conference on Applied Physics of Condensed Matter (APCOM 2017). June 12 - 14, 2017. Strbske Pleso, Slovak Republic Y1 - 2017 SP - 245 EP - 249 PB - Slovenska Technicka Univerzita CY - Bratislava ER - TY - CHAP A1 - Grobner, Marianne ED - Laske, Stephan ED - Orthey, Astrid ED - Schmid, Michael R. T1 - Sinn suchen und finden in Organisationen. Entwicklung mit Ansätzen der Existenzanalyse T2 - PersonalEntwickeln. Das aktuelle Nachschlagewerk für Praktiker Y1 - 2017 SN - 978-3-87156-116-0 PB - Deutscher Wirtschaftsdienst CY - Köln ET - 214. Erg.-Lfg. ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Moser, Sarah T1 - Effekte ärztlicher Koordination in Pflegeheimen - Literatursynopse und qualitative Ergebnisse eines Modellprojekts T2 - 6. Österreichischer Interdisziplinärer Palliativkongress. Festspielhaus Bregenz. 27. bis 29. April 2017. Kontroversen in Palliative Care. Abstractband Y1 - 2017 SP - 16 EP - 17 PB - Österreichische Palliativgesellschaft CY - Bregenz ER - TY - JOUR A1 - Preißinger, Markus A1 - Schwöbel, Johannes A. H. A1 - Klamt, Andreas A1 - Brüggemann, Dieter T1 - Multi-criteria evaluation of several million working fluids for waste heat recovery by means of Organic Rankine Cycle in passenger cars and heavy-duty trucks JF - Applied Energy KW - Automotive application KW - COSMO-RS KW - Multi-criteria evaluation KW - Organic Rankine Cycle KW - PubChem KW - Working fluid Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.apenergy.2017.08.212 SN - 0306-2619 VL - o.Jg. IS - Bd. 206 SP - 887 EP - 899 ER - TY - CHAP A1 - Brezany, Peter A1 - Ludescher, Thomas A1 - Feilhauer, Thomas ED - Biljanovic, Petar ED - Koricic, Marko ED - Skala, Karolj ED - Tihana Grbac, Galinac ED - Cicin-Sain, Marina ED - Sruk, Vlado ED - Ribaric, Slobodan ED - Gros, Stjepan ED - Vrdoljak, Boris ED - Mauher, Mladen ED - Tijan, Edvard ED - Hormot, Filip T1 - Cloud-dew computing support for automatic data analysis in life sciences T2 - Proceedings. 2017. 40th International Convention on Information and Communication Technology, Electronics and Microelectronics (MIPRO). May 22 – 26, 2017. Opatija, Croatia Y1 - 2017 U6 - http://dx.doi.org/10.23919/MIPRO.2017.7973450 SP - 365 EP - 370 ER - TY - CHAP A1 - Schneider, Reinhard A1 - Pilsan, Horatiu A1 - Wolber, Thomas A1 - Ludescher, Thomas T1 - Patientenzentriertes Langzeit – EKG. 104 – Biomedizin Innovativ – patientInnenfokussierte, anwendungsorientierte sowie interdisziplinäre Forschung am Puls der Zeit T2 - 11. FH–Forschungsforum 2017. Research - Innovation - Value. Tagungsband. 19. und 20. April 2017 Y1 - 2017 SP - 265 EP - 270 PB - IMC FH Krems GmbH CY - Krems ER - TY - JOUR A1 - Faessler, Bernhard A1 - Kepplinger, Peter A1 - Petrasch, Jörg T1 - Decentralized price-driven grid balancing via repurposed electric vehicle batteries JF - Energy KW - Battery storage KW - Distributed storage KW - Grid balancing KW - Optimization KW - Repurposed KW - Vehicle batteries Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.energy.2016.12.013 SN - 0360-5442 VL - o.Jg. IS - Bd. 118 SP - 446 EP - 455 ER - TY - JOUR A1 - Beyer, Hans-Georg A1 - Sendhoff, Bernhard T1 - Toward a steady-state analysis of an evolution strategy on a robust optimization problem with noise-induced multi-modality JF - IEEE Transactions on Evolutionary Computation Y1 - 2017 U6 - http://dx.doi.org/10.1109/TEVC.2017.2668068 VL - 21. Jg. IS - H. 4 SP - 629 EP - 643 ER - TY - JOUR A1 - Beyer, Hans-Georg A1 - Sendhoff, Bernhard T1 - Simplify your covariance matrix adaptation evolution strategy JF - IEEE Transactions on Evolutionary Computation Y1 - 2017 U6 - http://dx.doi.org/10.1109/TEVC.2017.2680320 VL - 21.Jg. IS - H. 5 SP - 746 EP - 759 ER - TY - CHAP A1 - Kempter, Guido A1 - Filkov, Rumen ED - Kempter, Guido ED - Hämmerle, Isabella T1 - Auswahl und Konfiguration von AAL-Lösungen T2 - Umgebungsunterstütztes Leben. Beiträge zum Usability Day XV. 22. Juni 2017 Y1 - 2017 SP - 54 EP - 59 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Künz, Andreas A1 - Dontschewa, Miglena A1 - Dietrich, Stefan A1 - Kopf, Sonja A1 - Münch, Martin ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Auswirkung von reaktivem Systemverhalten auf die Aufmerksamkeit von PassantInnen T2 - Design2product. Beiträge zur empirischen Designforschung. Die Bedeutung empirischer Designforschung für die Praxis T2 - design2product, 7 Y1 - 2017 SP - 91 EP - 101 PB - Bucher Verlag CY - Hohenems u.a. ET - 1. Auflage ER - TY - JOUR A1 - Akolkar, Anupam A1 - Rahmatian, Nima A1 - Unterberger, Seraphin A1 - Petrasch, Jörg T1 - Tomography based analysis of conduction anisotropy in fibrous insulation JF - International Journal of Heat and Mass Transfer Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.ijheatmasstransfer.2016.12.083 SN - 00179310 VL - o.Jg. IS - Bd. 108 B SP - 1740 EP - 1749 ER - TY - CHAP A1 - Fredersdorf, Frederic T1 - Ärztliche Koordination in stationären Einrichtungen der Altenpflege – Evaluation eines regionalen Modellprojekts. 102 – Innovation durch Evaluation: Impulse setzen durch Evaluationsprozesse im Social-Profit- und Public Health-Sektor T2 - 11. FH–Forschungsforum 2017. Research - Innovation - Value. Tagungsband. 19. und 20. April 2017 KW - Altenheim KW - Ärztliche Koordination KW - Modellprojekt KW - Palliativarbeit Y1 - 2017 SP - 122 EP - 128 PB - IMC FH Krems GmbH CY - Krems ER - TY - BOOK A1 - Fredersdorf, Frederic A1 - Jüster, Markus A1 - Rebitzer, Fabian A1 - Schiemenz, Cathrin T1 - Altersmigration und Gesundheitstourismus als Treiber regionalen Strukturwandels (AlGeTrei). IBH-Projekt im Rahmen der 4. Leistungsvereinbarung IBK-IBH 2014 - 2017 Y1 - 2017 SN - 978-3-7369-9686-1 PB - Cuvillier Verlag CY - Göttingen ET - 1. Auflage ER - TY - JOUR A1 - Mathis, Gebhard A1 - Hartmann, Siegfried A1 - Fredersdorf, Frederic T1 - Das Vorarlberger Modellprojekt "Ärztliche Koordination im Pflegeheim" - qualitative Analyse JF - Zeitschrift für Palliativmedizin KW - Ärztliche Koordination KW - Pflegeheim KW - Evaluation KW - Fokusgruppen KW - Interviews KW - Palliativmedizin Y1 - 2017 U6 - http://dx.doi.org/10.1055/s-0043-108437 SN - 1615-2921 VL - 18. Jg. IS - H. 5 SP - 232 EP - 233 ER - TY - BOOK A1 - Hofmeister, Werner A1 - Matt, Hubert T1 - Wi(e)derholung Y1 - 2017 PB - Museum für Quellenkultur CY - Klein St. Paul ER - TY - CHAP A1 - Dvorak, Michal A1 - Drahansky, Martin A1 - Kempter, Guido A1 - Mohelnikova, Jitka A1 - Luza, Radim A1 - Ritter, Walter A1 - Künz, Andreas ED - Kempter, Guido ED - Hämmerle, Isabella T1 - Usability and quality of light sources for households T2 - Umgebungsunterstütztes Leben. Beiträge zum Usability Day XV. 22. Juni 2017 Y1 - 2017 SP - 125 EP - 133 PB - Pabst Science Publishers CY - Lengerich ER - TY - CHAP A1 - Mössinger, Oliver ED - Mair, Olivia ED - Koje - Koordinationsbüro für Offene Jugendarbeit und Entwicklung, T1 - Jugendsozialarbeit im Feld der Sozialen Arbeit am Beispiel der Jugendsozialarbeit im Handlungsfeld der Offenen Jugendarbeit T2 - 156 starke Impulse. Zehn Jahre Jugendsozialarbeit im Handlungsfeld der Offenen Jugendarbeit in Vorarlberg KW - +SSD 302 KW - Jugendarbeit : Vorarlberg Y1 - 2017 SN - 978-3-200-05237-6 SP - 61 EP - 68 PB - Koje - Koordinationsbüro für Offene Jugendarbeit und Entwicklung CY - Bregenz ER - TY - CHAP A1 - Matt, Hubert ED - Thaler, Jürgen T1 - Schachtelsätze. Ein Versuch über die Kasetten-Sammlung von Gerhard Hartmann T2 - Sammlung Hartmann - Kassetten. Vorarlberger Landesbibliothek, Bregenz Y1 - 2017 SP - 38 EP - 55 PB - Kehrer CY - Heidelberg u.a. ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Der Erkundungstrip durch die Problematik. Problemlösungsprozesse initiiren JF - TrainerJournal Y1 - 2017 VL - o.Jg. IS - Nr. 92 SP - 25 ER - TY - CHAP A1 - Mayer, Horst O. ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Wenn’s um die Wurst geht: Unterschiedliche Verpackungs-Designs für Wurstwaren T2 - Design2product. Beiträge zur empirischen Designforschung. Die Bedeutung empirischer Designforschung für die Praxis T2 - design2product, 7 KW - +AWD 520 D2P KW - +KDC 122 KW - Design : Theorie, Reflexion KW - Fachhochschule Vorarlberg : Design2product Y1 - 2017 SN - 978-3-99018-439-4 SP - 11 EP - 37 PB - Bucher Verlag CY - Hohenems u.a. ET - 1. Auflage ER - TY - CHAP A1 - Kriz, Willy Christian ED - Roehl, Heiko ED - Asselmeyer, Herbert T1 - Teamkompetenz als Schlüssel zur Organisationsentwicklung T2 - Organisationen klug gestalten. Das Handbuch für Organisationsentwicklung und Change Management Y1 - 2017 SP - 328 EP - 333 PB - Schäffer-Poeschel CY - Stuttgart ER - TY - JOUR A1 - Moser, Sarah A1 - Luxenberger, Wolfgang A1 - Freidl, Wolfgang T1 - Wahrnehmung von Hörproblemen bei älteren Menschen JF - HNO Y1 - 2017 U6 - http://dx.doi.org/10.1007/s00106-017-0334-z VL - 65. Jg. IS - H. 8 SP - 671 EP - 679 ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Manahl, Werner A1 - Kikkawa, Toshiko T1 - Systems management education through simulation game design T2 - Proceedings of JASAG National Conference. May 2017. Social System Gaming. 2017 Spring National Conference. May 27 & 28, 2017 Y1 - 2017 SP - 84 EP - 85 PB - Ryutsu Keizai University CY - Chiba ER - TY - JOUR A1 - Baumeister, Alexander A1 - Ilg, Markus T1 - Prozesskostenbasierte Kalkulation agiler Softwareprojekte JF - Akademie. Die Wissen schafft. Zeitschrift für Führungskräfte in Verwaltung und Wirtschaft Y1 - 2017 VL - 62. Jg. IS - H. 4 SP - 111 EP - 117 ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Types of gaming simulation applications JF - Simulation & Gaming Y1 - 2017 U6 - http://dx.doi.org/10.1177/1046878117689860 SN - 1046-8781 VL - 48. Jg. IS - H. 1 SP - 3 EP - 7 ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Patze-Diordiychuk, Peter ED - Smettan, Jürgen ED - Renner, Paul ED - Föhr, Tanja T1 - Szenariotechnik T2 - Methodenhandbuch Bürgerbeteiligung. Band 2: Passende Beteiligungsformate wählen Y1 - 2017 SN - 978-3-86581-853-9 SP - 162 EP - 178 PB - oekom CY - München ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Organisationsstruktur eines Kompetenzzentrums in einer unübersichtlichen VUCA-Welt JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2017 VL - 16. Jg. IS - H. 1 SP - 111 EP - 117 ER - TY - BOOK A1 - Wilms, Falko E. P. T1 - Machen Sie doch was Sie wollen T3 - Arbeitsberichte des Competence Center of Communication & Collaboration, 3 KW - +WBF 320 KW - Entscheidungstheorie, Problemlösung Y1 - 2017 PB - FH Vorarlberg CY - Dornbirn ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Machen Sie, was Sie wollen. Diese Einsichten helfen Ihnen dabei JF - Journal bso. Berufsverband für Coaching, Supervision und Organisationsberatung Y1 - 2017 VL - o.Jg. IS - Bd. 2 SP - 18 EP - 22 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Kommunikative Problemlösungen. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2017 VL - o.Jg. IS - Nr. 91 ER - TY - THES A1 - Hefel, Johanna T1 - Sterben und Tod im Kontext des Bachelorstudiums Soziale Arbeit an österreichischen Fachhochschulen Y1 - 2017 PB - Universität CY - Innsbruck ER - TY - JOUR A1 - Chien, Huei-Ting A1 - Pölzl, Markus A1 - Koller, Georg A1 - Challinger, Susanna A1 - Fairbairn, Callum A1 - Baikie, Iain A1 - Kratzer, Markus A1 - Teichert, Christian A1 - Friedel, Bettina T1 - Effects of hole-transport layer homogeneity in organic solar cells – A multi-length scale study JF - Surfaces and Interfaces KW - Colloidal films KW - Hole-transport layer KW - Organic solar cells KW - Photocurrent mapping KW - Spatial inhomogeneity KW - Surface potential distribution Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.surfin.2016.11.008 SN - 2468-0230 VL - o.Jg. IS - Bd. 6 SP - 72 EP - 80 ER - TY - JOUR A1 - Chien, Huei-Ting A1 - Zach, Peter W. A1 - Friedel, Bettina T1 - Short-term environmental effects and their influence on spatial homogeneity of organic solar cell functionality JF - ACS Applied Materials & Interfaces KW - environmental degradation KW - organic solar cells KW - parallel microdiodes KW - photocurrent mapping KW - spatial homogeneity Y1 - 2017 U6 - http://dx.doi.org/10.1021/acsami.7b08365 SN - 1944-8252 VL - 9. Jg. IS - H. 33 SP - 27754 EP - 27764 ER - TY - JOUR A1 - Ebner, Michael A1 - Schennach, Robert A1 - Chien, Huei-Ting A1 - Mayrhofer, Claudia A1 - Zankel, Armin A1 - Friedel, Bettina T1 - Regenerated cellulose fiber solar cell JF - Flexible and Printed Electronics KW - Cellulose Fiber Solar Cell Y1 - 2017 U6 - http://dx.doi.org/10.1088/2058-8585/aa5707 SN - 2058-8585 VL - 2. Jg. IS - 1/014002 ER - TY - CHAP A1 - Feyel, Katharina A1 - Mayer, Horst O. ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Multisensuales Marketing im Lebensmitteleinzelhandel am Beispiel Sutterlüty T2 - Design2product. Beiträge zur empirischen Designforschung. Die Bedeutung empirischer Designforschung für die Praxis T2 - design2product, 7 KW - +AWD 520 D2P KW - +KDC 122 KW - Design : Theorie, Reflexion KW - Fachhochschule Vorarlberg : Design2product Y1 - 2017 SN - 978-3-99018-439-4 SP - 39 EP - 67 PB - Bucher Verlag CY - Hohenems u.a. ET - 1. Auflage ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Auchter, Eberhard A1 - Wittenzellner, Helmut ED - Mieke, Christian ED - Siemon, Cord T1 - Planspiele für die Gründerausbildung an Hochschulen. Planspiele in der Hochschuldidaktik T2 - Gründung und Innovation KW - +WBB 150 KW - +WBB 300 KW - Unternehmen : Innovation KW - Unternehmensgründung Y1 - 2017 SN - 978-3-8325-4430-0 SP - 107 EP - 134 PB - Logos Verlag CY - Berlin ER - TY - JOUR A1 - Kuboth, Sebastian A1 - Neubert, Marc A1 - Preißinger, Markus A1 - Brüggemann, Dieter T1 - Iterative approach for the design of an organic rankine cycle based on thermodynamic process simulations and a small-scale test rig JF - Energy Procedia KW - Organic Rankine Cycle KW - scroll expander KW - small scale KW - waste heat recovery Y1 - 2017 U6 - http://dx.doi.org/10.1016/j.egypro.2017.09.167 SN - 1876-6102 VL - o.Jg. IS - Bd. 129 SP - 18 EP - 25 ER - TY - CHAP A1 - Wernig, Nadja Mercedes A1 - Simma, Armin T1 - Automated protocol for the establishment of encrypted e-mail communication (APEEEC) T2 - 16th European Conference on Cyber Warfare and Security (ECCWS17) T2 - Proceedings of the 16th European Conference on Cyber Warfare and Security Y1 - 2017 SP - 527 EP - 536 PB - Academic Bookshop CY - Dublin, Ireland ER - TY - CHAP A1 - Rebitzer, Fabian A1 - Mayer, Horst O. A1 - Mayer, Brigitte ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Test des 3D-Silikon-Printverfahrens am Beispiel des Wolford Cotton Line Bras T2 - Design2product. Beiträge zur empirischen Designforschung. Die Bedeutung empirischer Designforschung für die Praxis T2 - design2product, 7 Y1 - 2017 SP - 69 EP - 88 PB - Bucher Verlag CY - Hohenems u.a. ET - 1. Auflage ER - TY - JFULL ED - Timothy C., Clapper ED - Harviainen, J. Tuomas ED - Kriz, Willy Christian T1 - Simulation & Gaming. An Interdisciplinary Journal of Theory, Practice and Research Y1 - 2017 VL - 48 ER - TY - JOUR A1 - Moser, Sarah A1 - Luxenberger, Wolfgang A1 - Freidl, Wolfgang T1 - The influence of social support and coping on quality of life among elderly with age-related hearing loss JF - American Journal of Audiology Y1 - 2017 U6 - http://dx.doi.org/10.1044/2017_AJA-16-0083 SN - 1558-9137 VL - 26. Jg. IS - H. 2 SP - 170 EP - 179 ER - TY - CHAP A1 - Ganahl, Simon A1 - Matt, Hubert ED - Thaler, Jürgen T1 - Felder und Karten. Ein schriftlicher Dialog über die Sozialgeografie, in Franz Michael Felders Nümmamüllers und das Schwarzokaspale T2 - Jahrbuch. Franz-Michael-Felder-Archiv der Vorarlberger Landesbibliothek, 18. Jahrgang 2017 Y1 - 2017 SP - 115 EP - 157 PB - Franz-Michael-Felder-Archiv der Vorarlberger Landesbibliothek CY - Bregenz ER - TY - JOUR A1 - Faessler, Bernhard A1 - Schuler, Michael A1 - Preißinger, Markus A1 - Kepplinger, Peter T1 - Battery storage systems as grid-balancing measure in low-voltage distribution grids with distributed generation JF - Energies Y1 - 2017 U6 - http://dx.doi.org/10.3390/en10122161 SN - 1996-1073 VL - 10. Jg. IS - H. 12/2161 ER - TY - CHAP A1 - Mayer, Horst O. ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Befragung der Vorarlberger Bauträger und Immobilienmakler 2017 T2 - Design2product. Beiträge zur empirischen Designforschung. Die Bedeutung empirischer Designforschung für die Praxis T2 - Design2product, 7 Y1 - 2017 SP - 125 EP - 147 PB - Bucher Verlag CY - Hohenems u.a. ET - 1. Auflage ER - TY - JOUR T1 - SEMRADAR BT - Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2017 VL - 16 ER - TY - BOOK ED - Kempter, Guido ED - Hämmerle, Isabella T1 - Umgebungsunterstütztes Leben. Beiträge zum Usability Day XV. 22. Juni 2017 KW - +INC 310 KW - +INC 320 KW - +SSC 658.1 WAL KW - Benutzerschnittstelle KW - Mensch-Maschine-Kommunikation KW - Wohnen : Alter : Soziologie Y1 - 2017 SN - 978-3-95853-316-5 N1 - Beiträge überwiegend deutsch, teilweise englisch PB - Pabst Science Publishers CY - Lengerich ER - TY - JOUR A1 - Grobner, Marianne T1 - Externe Beratung bei Veränderungsprozessen JF - changement! Veränderungsprozesse aktiv und erfolgreich gestalten Y1 - 2017 VL - o.Jg. IS - H. 4 SP - 20 EP - 24 ER - TY - CHAP A1 - Seyringer, Dana A1 - Burtscher, Catalina A1 - Partel, Stefan A1 - Edlinger, Johannes A1 - Maese-Novo, Alejandro A1 - Muellner, Paul A1 - Hainberger, Rainer A1 - Kraft, Jochen A1 - Koppitsch, Günther A1 - Meinhardt, Gerald ED - Garcia-Blanco, Sonia ED - Nunzi Conti, Gualtiero T1 - Design and simulation of 20-channel 50-GHz Si3N4-based arrayed waveguide grating applying AWG-parameters tool T2 - Integrated Optics. Devices, Materials, and Technologies XXI. 30 January–1 February 2017. San Francisco, California, United States Y1 - 2017 U6 - http://dx.doi.org/10.1117/12.2249675 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Dobler, Martin A1 - Schumacher, Jens T1 - Innovation and emerging ICT in logistics for Europe. Position paper for the workshop 'is logistics catching up the pace of emerging technologies?' T2 - Engineering, Technology & Innovation Management Beyond 2020: New Challenges, New Approaches. 2017 International Conference on Engineering, Technology and Innovation (ICE/ITMC). Conference Proceedings. 23rd ICE/ITMC Conference. 27 - 29 June 2017. Funchal, Madeira Island, Portugal Y1 - 2017 SN - 978-1-5386-0774-9 U6 - http://dx.doi.org/10.1109/ICE.2017.8280061 SP - 1509 EP - 1516 PB - IEEE CY - Danvers ER - TY - CHAP A1 - Beyer, Hans-Georg A1 - Hellwig, Michael T1 - Analysis of the pcCMSA-ES on the noisy ellipsoid model T2 - GECCO '17. Proceedings of the 2017 Genetic and Evolutionary Computation Conference. July 15-19, 2017. Berlin, Germany KW - dynamical systems approach KW - evolution strategies KW - noisy ellipsoid model KW - population size control KW - self-adaptation Y1 - 2017 SN - 978-1-4503-4920-8 U6 - http://dx.doi.org/10.1145/3071178.3079195 SP - 689 EP - 696 PB - ACM CY - New York, NY ER - TY - CHAP A1 - Unterkofler, Karl A1 - Teschl, Susanne T1 - Reproducibility and verification of real time breath VOCs concentration data by modeling. 104 – Biomedizin Innovativ – patientInnenfokussierte, anwendungsorientierte sowie interdisziplinäre Forschung am Puls der Zeit T2 - 11. FH-Forschungsforum 2017. Research - Innovation - Value. Tagungsband. 19. und 20. April 2017 Y1 - 2017 SP - 240 EP - 244 PB - IMC FH Krems GmbH CY - Krems ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Rehm, Sven Volker ED - Fischer, Thomas T1 - Die Systemtheorie im St. Galler Management-Modell T2 - Kybernetik und Transformation. Regelung und Kommunikation in Organisation und Gesellschaft. Wissenschaftliche Jahrestagung der Gesellschaft für Wirtschafts- und Sozialkybernetik vom 13. bis 14. Oktober 2015 in Vallendar am Rhein Y1 - 2017 SN - 978-3-428-15193-6 SP - 211 EP - 221 PB - Duncker & Humblot CY - Berlin ER - TY - CHAP A1 - Wilms, Falko E. P. T1 - Die Organisation als Soziales System - Eine sozialkybernetische Betrachtung T2 - Digitale Welten: neue Ansätze in der Wirtschafts- und Sozialkybernetik. Konferenz für Wirtschafts- und Sozialkybernetik. KyWi 2014 vom 10. bis 11. Juli 2014 in Stuttgart KW - Organisationssoziologie KW - Sozialtechnologie KW - Theorie Y1 - 2017 SN - 978-3-428-14949-0 SP - 55 EP - 70 PB - Duncker & Humblot CY - Berlin ER - TY - CHAP A1 - Otto, Ulrich A1 - Kaspar, Heidi A1 - Kempter, Guido T1 - IBH - Living Lab »Active & Assisted Living« T2 - Abstractband. Gemeinsame Jahrestagung der Sektion III: Sozial- und verhaltenswissenschaftliche Gerontologie und der Sektion IV: Soziale Gerontologie und Altenarbeit der Deutschen Gesellschaft für Gerontologie und Geriatrie (DGGG) Fulda 2017 Y1 - 2017 UR - http://dggg-ft2017.aey-congresse.de/start.html SP - 127 ER - TY - GEN A1 - Otto, Ulrich A1 - Kaspar, Heidi A1 - Hegedüs, Anna A1 - Hämmerle, Isabella A1 - Kempter, Guido T1 - Technik als Hilfe im Alltag – das Zuhause als «Versuchslabor». [Projektposter] Y1 - 2017 UR - https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=2ahUKEwjwltuixprpAhW6A2MBHcp_Cy0QFjAAegQIAhAB&url=https%3A%2F%2Fwww.kalaidos-fh.ch%2F-%2Fmedia%2FFiles%2FKalaidos-Bildungsgruppe-Schweiz%2FKalaidos-FH%2FDepartement-Gesundheit%2FCareum-Forschung%2FAgeing-At-Home-Projekte%2F2017Otto-et-alTechnik-als-Hilfe-im-Alltag.pdf%3Fla%3Dde-CH%26hash%3D3881D1D601FA537B788A234A2158FFFCEAEB2FFE&usg=AOvVaw35D7amdmPThHa6cGMuX1eJ ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Stamatov, Denise A1 - Marinov, Marin B. ED - Tsenov, Alexandar ED - Heupel, Thomas ED - Zug, Sebastian ED - Lang, Peter ED - Ovcharova, Jivka ED - Yordanov, Hristomir T1 - Concept and development of a VR-application. Konzept und Entwicklung einer VR-Anwendung T2 - FDIBA Conference Proceedings, 1 T2 - The Digital Transformation: Challenges in Technological, Scientific and Social Development. Proceedings of the 7th FDIBA Conference. Sofia, Bulgaria, 30 November – 1 December, 2017 Y1 - 2017 UR - http://conference.fdiba.tu-sofia.bg/?page_id=338 SP - 81 EP - 84 PB - TU–Sofia Publishing house CY - Sofia ER - TY - CHAP A1 - Dobler, Martin A1 - Schumacher, Jens ED - Pawar, Kulwant S. ED - Potter, Andrew T. ED - Lisec, Andrej T1 - On the integration of intelligent logistics ecosystems in production and industry 4.0 settings T2 - Proceedings of the 22nd International Symposium on Logistics (ISL 2017 ). Data Driven Supply Chains. Lubljana, Slovenia. 9 - 12th July 2017 Y1 - 2017 UR - http://www.isl21.org/wp-content/uploads/2017/10/ISL-Proceedings-2017.pdf SP - 314 EP - 320 PB - Nottingham University Business School CY - Nottingham ER - TY - CHAP A1 - Kargl, Alexandra A1 - Mössinger, Oliver A1 - Amann, Bernhard ED - Amt der Vorarlberger Landesregierung, Abt. VIIa – Raumplanung und Baurecht T1 - Quartier sind wir. Gemeinwesenarbeit ist unser aller Arbeit T2 - Willkommen im Quartier. Von Dorfentwicklung und Städtebau in Vorarlberg Y1 - 2017 UR - https://vorarlberg.at/documents/21336/101677/Schriftenreihe+28+Willkommen+im+Quartier.pdf/b5a6fa33-a0c5-4bbb-817c-4911ce4bd900?version=1.2 SP - 54 EP - 59 PB - Amt der Vorarlberger Landesregierung CY - Bregenz ET - 2. Auflage ER - TY - BOOK A1 - Breuer, Thomas T1 - What conclusions can be drawn from the EBA 2016 Market Risk Benchmarking Exercise? Banking Union Scrutiny. In-depth analysis. Requested by the ECON committee Y1 - 2017 UR - http://www.europarl.europa.eu/thinktank/en/document.html?reference=IPOL_IDAN(2017)602103 PB - Economic Governance Support Unit CY - o.O. ER - TY - JOUR A1 - Domke, Matthias A1 - Egle, Bernadette A1 - Stroj, Sandra A1 - Bodea, Marius A1 - Schwarz, Elisabeth A1 - Fasching, Gernot T1 - Ultrafast-laser dicing of thin silicon wafers: strategies to improve front- and backside breaking strength JF - Applied Physics A Y1 - 2017 U6 - http://dx.doi.org/10.1007/s00339-017-1374-7 VL - 123 IS - 12/746 ER - TY - JOUR A1 - Arzbacher, Stefan A1 - Petrasch, Jörg A1 - Ostermann, Alexander A1 - Loerting, Thomas T1 - Micro-tomographic investigation of ice and clathrate formation and decomposition under thermodynamic monitoring JF - Materials KW - pejoPapers KW - printed Y1 - 2016 U6 - http://dx.doi.org/10.3390/ma9080668 SN - 1996-1944 VL - 9. Jg. IS - H. 8/668 ER - TY - JOUR A1 - Fäßler, Bernhard A1 - Kepplinger, Peter A1 - Petrasch, Jörg T1 - Decentralized price-driven grid balancing via repurposed electric vehicle batteries. Veröffentlichungsdatum Web: 27. Dezember 2016 JF - Energy Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.energy.2016.12.013 SN - 03605442 VL - o.Jg. IS - Bd. 118 SP - 446 EP - 455 ER - TY - CHAP A1 - Seyringer, Dana A1 - Burtscher, Catalina A1 - Partel, Stefan A1 - Edlinger, Johannes A1 - Maese-Novo, Alejandro A1 - Muellner, Paul A1 - Hainberger, Rainer A1 - Kraft, Jochen A1 - Koppitsch, Günther A1 - Meinhardt, Gerald ED - Garcia-Blanco, Sonia M. ED - Nunzi Conti, Gualtiero T1 - Design and simulation of Si3N4 based arrayed waveguide gratings applying AWG-parameters tool T2 - 2016 18th International Conference on Transparent Optical Networks (ICTON). Trento, Italy, July 10-14, 2016 KW - arrayed waveguide gratings KW - Couplers KW - Crosstalk KW - integrated optics KW - AWG-parameters tool KW - frequency 100 GHz KW - transmission characteristics KW - Photonics KW - Refractive index KW - silicon compounds KW - AWG KW - commercial photonics tools KW - high index contrast AWG KW - light polarisation KW - medical diagnostic imaging applications KW - Optical fiber sensors KW - photonic integrated circuit KW - Si3N4 KW - Si3N4 based AWGs KW - silica based AWG designs KW - SiO2 KW - TM-polarized light KW - wavelength 850 nm Y1 - 2016 ER - TY - JOUR A1 - Ilg, Markus T1 - Crowdfunding - Chancen und Risiken für Unternehmen und Investoren, Herausforderungen für Finanzcontroller JF - Controller Magazin. Arbeitsergebnisse aus der Controller-Praxis Y1 - 2016 VL - 141. Jg. IS - H. 1 ER - TY - CHAP A1 - Kempter, Guido A1 - Künz, Andreas ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Smart Home und Smart Mobility für ökologische Nachhaltigkeit T2 - Design2product. Beiträge zur empirischen Designforschung. Datenvisualisierung Y1 - 2016 SP - 71 EP - 86 PB - Bucher Verlag CY - Hohenems u.a. ER - TY - CHAP A1 - Zehetner, Johann A1 - Vanko, Gabriel A1 - Dzuba, Jaroslav A1 - Lalinsky, Tibor A1 - Lucki, Michal A1 - Kraus, Stanislav ED - Vajda, Jan ED - Jamnicky, Igor T1 - Micro structuring of bulk SiC substrates by femtosecond laser ablation T2 - Proceedings of the 22nd International Conference on Applied Physics of Condensed Matter (APCOM 2016). June 22 - 24, 2016. Hotel Patria, Strbske Pleso, Slovak Republic Y1 - 2016 SP - 302 EP - 306 PB - Slovenska Technicka Univerzita CY - Bratislava ER - TY - CHAP A1 - Weber, Wolfgang ED - Proske, Wolfgang T1 - Dr. habil. Edwin Albrich: als Arzt jederzeit verwendbar T2 - NS-Belastete aus dem Bodenseeraum KW - +SAE 177 NAT KW - +SAE 186 V KW - Nationalsozialismus : Geschichte KW - Vorarlberg : Geschichte Y1 - 2016 SN - 978-3-945893-04-3 SP - 20 EP - 34 PB - Kugelberg Verlag CY - Gerstetten ER - TY - CHAP A1 - Seyringer, Dana ED - Laudon, Matthew ED - Romanowicz, Bart T1 - Application of angular method to correct channel spacing between AWG demultiplexed channels T2 - Advanced Manufacturing, Electronics and Microsystems. TechConnect Briefs 2016 Y1 - 2016 SP - 267 EP - 271 PB - TechConnect CY - Danville, CA ER - TY - THES A1 - Partel, Stefan T1 - Fabrication of interdigitated electrode arrays for biosensors by advanced mask aligner lithography Y1 - 2016 PB - Universität CY - Freiburg ER - TY - CHAP A1 - Lechner, Verena A1 - Weidmann, Karl-Heinz A1 - Hämmerle, Isabella ED - Marcus, Aaron T1 - Systematic application of circle-similar shapes to visualize database-homogeneity in a Big Data environment T2 - Design, User Experience, and Usability. Technological Contexts. 5th International Conference, DUXU 2016. Held as part of HCI International 2016. Toronto, Canada, July 17 – 22, 2016. Proceedings. Part III Y1 - 2016 SN - 978-3-319-40405-9 SP - 167 EP - 179 PB - Springer CY - o.O. ER - TY - CHAP A1 - Lechner, Verena A1 - Weidmann, Karl-Heinz A1 - Hämmerle, Isabella ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Systematische Anwendung von kreisähnlichen Formen zur Visualisierung von Datenbank-Performance im Big Data-Umfeld T2 - Design2product. Beiträge zur empirischen Designforschung. Datenvisualisierung Y1 - 2016 SP - 37 EP - 51 PB - Bucher Verlag CY - Hohenems u.a. ER - TY - BOOK ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Design2product. Beiträge zur empirischen Designforschung. Datenvisualisierung T3 - design2product, 6 KW - +KDC 122 KW - Design : Theorie, Reflexion KW - +IGC 430 KW - Informationswiedergabe : Visualisierung Y1 - 2016 SN - 978-3-99018-401-1 PB - Bucher Verlag CY - Hohenems u.a. ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Konstruktive Aussprache statt irreführende Diskussion. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2016 VL - o.Jg. IS - Nr. 90 ER - TY - JOUR A1 - Bandic, Mario A1 - Verbanac, Giuli A1 - Moldwin, Mark B. A1 - Pierrard, Viviane A1 - Piredda, Giovanni T1 - MLT dependence in the relationship between plasmapause, solar wind, and geomagnetic activity based on CRRES: 1990–1991 JF - Journal of Geophysical Research. Space Physics KW - 2768 Plasmasphere KW - 2784 Solar wind/magnetosphere interactions KW - CRESS satellite KW - geomagnetic activity KW - plasmapause KW - solar wind Y1 - 2016 U6 - http://dx.doi.org/10.1002/2015JA022278 SN - 2169-9402 VL - 121. Jg. IS - H. 5 SP - 4397 EP - 4408 ER - TY - JOUR A1 - Martin-Sanchez, Javier A1 - Trotta, Rinaldo A1 - Piredda, Giovanni A1 - Schimpf, Christian A1 - Trevisi, Giovanna A1 - Seravalli, Luca A1 - Frigeri, Paola A1 - Stroj, Sandra A1 - Lettner, Thomas A1 - Reindl, Marcus A1 - Wildmann, Johannes S. A1 - Edlinger, Johannes A1 - Rastelli, Armando T1 - Reversible control of in-plane elastic stress tensor in nanomembranes JF - Advanced Optical Materials Y1 - 2016 U6 - http://dx.doi.org/10.1002/adom.201500779 VL - 4. Jg. IS - H. 5 SP - 682 EP - 687 ER - TY - CHAP A1 - Zehetner, Johann A1 - Vanko, Gabriel A1 - Dzuba, Jaroslav A1 - Lalinsky, Tibor A1 - Lucki, Michal A1 - Kraus, Stanislav ED - Kovac, Jaroslav ED - Michalka, Miroslav ED - Kovacova, Sona ED - Jandura, Daniel T1 - Micro structuring of membranes for sensor devices on different nulk materials by femtosecond laser ablation T2 - Proceedings of ADEPT. 4th International Conference on Advances in Electronic and Photonic Technologies. Tatranska Lomnica, High Tatras, Slovakia. June 20 - 23, 2016 Y1 - 2016 SP - 55 EP - 58 PB - University of Zilina CY - Zilina ER - TY - JOUR A1 - Trotta, Rinaldo A1 - Martin-Sanchez, Javier A1 - Wildmann, Johannes S. A1 - Piredda, Giovanni A1 - Reindl, Marcus A1 - Schimpf, Christian A1 - Zallo, Eugenio A1 - Stroj, Sandra A1 - Edlinger, Johannes A1 - Rastelli, Armando T1 - Wavelength-tunable sources of entangled photons interfaced with atomic vapours JF - Nature Communications Y1 - 2016 U6 - http://dx.doi.org/10.1038/ncomms10375 SN - 2041-1723 VL - o.Jg. IS - Nr. 10375 ER - TY - JOUR A1 - Domke, Matthias A1 - Egle, Bernadette A1 - Piredda, Giovanni A1 - Stroj, Sandra A1 - Fasching, Gernot A1 - Bodea, Marius A1 - Schwarz, Elisabeth T1 - Ultrashort pulse laser dicing of thin Si wafers. The influence of laser-induced periodic surface structures on the backside breaking strength JF - Journal of Micromechanics and Microengineering Y1 - 2016 U6 - http://dx.doi.org/10.1088/0960-1317/26/11/115004 SN - 0960-1317 VL - 26. Jg. IS - H. 11 ER - TY - JOUR A1 - Zehetner, Johann A1 - Kraus, Stanislav A1 - Lucki, Michal A1 - Vanko, Gabriel A1 - Dzuba, Jaroslav A1 - Lalinsky, Tibor T1 - Manufacturing of membranes by laser ablation in SiC, sapphire, glass and ceramic for GaN/ferroelectric thin film MEMS and pressure sensors JF - Microsystem Technologies Y1 - 2016 U6 - http://dx.doi.org/10.1007/s00542-016-2887-2 SN - 0946-7076 SN - 1432-1858 VL - 22. Jg. IS - H. 7 SP - 1883 EP - 1892 ER - TY - CHAP A1 - Seyringer, Dana A1 - Gajdosova, Lenka A1 - Burtscher, Catalina ED - Michalka, Miroslav ED - Vincze, Andrej T1 - Arrayed waveguide gratings: design and simulation T2 - 19. Skola Vakuovej Techniky. Vakuum a nove materialy. Vacuum and new materials. Zbornik prispevkov. 9. - 12. November 2016. Strbske Pleso. Hotel Trigan Y1 - 2016 PB - Slovenska vakuova spolocnost u.a. CY - Bratislava ER - TY - JOUR A1 - Domke, Matthias A1 - Piredda, Giovanni A1 - Zehetner, Johann A1 - Stroj, Sandra T1 - Minimizing the surface roughness for silicon ablation with ultrashort laser pulses JF - JLMN - Journal of Laser Micro/Nanoengineering Y1 - 2016 U6 - http://dx.doi.org/10.2961/jlmn.2016.01.0019 VL - 11. Jg. IS - H. 1 SP - 100 EP - 103 ER - TY - CHAP A1 - Burtscher, Catalina A1 - Seyringer, Dana A1 - Lucki, Michal ED - Kovac, Jaroslav ED - Michalka, Miroslav ED - Kovacova, Sona ED - Jandura, Daniel T1 - Study of splitting properties of 1x16 splitter MMI splitter based on different widths of the multimode interference section T2 - Proceedings of ADEPT. 4th International Conference on Advances in Electronic and Photonic Technologies. Tatranska Lomnica, High Tatras, Slovakia. June 20 - 23, 2016 Y1 - 2016 SP - 127 EP - 130 PB - University of Zilina CY - Zilina ER - TY - CHAP A1 - Burtscher, Catalina A1 - Seyringer, Dana A1 - Lucki, Michal T1 - Study of the optical properties of 1x16 splitter based on Y-branch and MMI approaches T2 - 2016 18th International Conference on Transparent Optical Networks (ICTON). Trento, Italy, July 10-14, 2016 KW - integrated optics KW - Optical fibers KW - asymmetric splitting ratio KW - High-speed optical techniques KW - MMI KW - MMI splitter KW - multimode interference splitter KW - optical beam splitters KW - Optical device fabrication KW - Optical polarization KW - optical properties KW - optical splitting KW - splitter KW - Y-branch KW - Y-branch splitter Y1 - 2016 ER - TY - CHAP A1 - Mayer, Horst O. A1 - Duelli, Alexander A1 - Sturn, Mathias ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - 3D Visualisierungen und Studiofotografie. Ein Vergleich der Eindruckswirkung T2 - Design2product. Beiträge zur empirischen Designforschung. Datenvisualisierung Y1 - 2016 SN - 978-3-99018-401-1 SP - 13 EP - 35 PB - Bucher Verlag CY - Hohenems u.a. ER - TY - CHAP A1 - Kriz, Willy Christian ED - Ameln, Falko von ED - Kramer, Josef T1 - Planspiele zum Erwerb von Teamkompetenz in Organisationen T2 - Organisationen in Bewegung bringen. Handlungsorientierte Methoden für die Personal-, Team- und Organisationsentwicklung Y1 - 2016 SP - 164 EP - 167 PB - Springer CY - Berlin u.a. ET - 2., überarb. Aufl. ER - TY - BOOK A1 - Seyringer, Dana T1 - Arrayed Waveguide Gratings T3 - SPIE.Spotlight Y1 - 2016 SN - 978-1-5106-0359-2 PB - SPIE CY - Bellingham, Wash. ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Gaming simulation for individual, collective, and organizational learning JF - ThaiSim Journal. Learning Development (TSJLD) Y1 - 2016 VL - 1. Jg. IS - Bd. 1 SP - 25 EP - 37 ER - TY - CHAP A1 - Moser, Sarah T1 - Association between perceived social support and quality of life among elderly with age-related hearing loss in Austria T2 - HeAL 2016. Hearing Across the Lifespan. June 2-4, 2016. Cernobbio (Como Lake), Italy. Program Y1 - 2016 UR - http://www.heal2016.org PB - NHS u.a. CY - Cernobbio ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Laukamp, Bernhard Siegfried T1 - Wenn remote Teams nicht funktionieren. Leitung eines verteilten Teams T2 - Die Nachwuchs-Führungskraft. Ihre Probleme - ihre Lösungen KW - +WBF 105 KW - Führungskraft Y1 - 2016 SN - 978-3-7664-9940-0 SP - 174 EP - 183 PB - Jünger Medien CY - Offenbach ER - TY - CHAP A1 - Domke, Matthias A1 - Gratt, Johannes A1 - Sroka, Ronald ED - Heisterkamp, Alexander ED - Herman, Peter R. ED - Meunier, Michel ED - Nolte, Stefan T1 - Fabrication of homogeneously emitting optical fiber diffusors using fs-laser ablation T2 - Frontiers in Ultrafast Optics. Biomedical, Scientific, and Industrial Applications XVI Y1 - 2016 PB - SPIE CY - San Francisco, Cal. ER - TY - CHAP A1 - Partel, Stefan A1 - Urban, Gerald ED - Erdmann, Andreas ED - Kye, Jongwook T1 - Innovative method to suppress local geometry distortions for fabrication of interdigitated electrode arrays with nano gaps T2 - Optical Microlithography. 23–25 February 2016. San Jose, California, United States Y1 - 2016 PB - SPIE CY - Bellingham, Wash. ER - TY - JOUR A1 - Fredersdorf, Frederic A1 - Mathis, Gebhard A1 - Sonnweber, Monika T1 - Ärztliche Koordination im Heim. Ein Projekt des Landes Vorarlberg JF - Lebenswelt Heim. Zeitschrift des Bundesverbandes der Alten- und Pflegeheime Österreichs Y1 - 2016 VL - 19. Jg. IS - H. 72 SP - 22 EP - 23 ER - TY - JOUR A1 - Heller-Künz, Helene A1 - Mayer, Brigitte T1 - Schreibzentrumsarbeit als integriertes Tätigkeitsfeld einer Hochschulbibliothek. Das Schreibzentrum der Bibliothek der FH Vorarlberg. Ein Praxisbericht JF - Bibliothek. Forschung und Praxis Y1 - 2016 U6 - http://dx.doi.org/10.1515/bfp-2016-0062 SN - 0341-4183 VL - 40. Jg. IS - H. 3 SP - 370 EP - 374 ER - TY - CHAP A1 - Weber, Wolfgang ED - Daniel, Ute ED - Gatrell, Peter ED - Janz, Oliver ED - Jones, Heather ED - Keene, Jennifer D. ED - Kramer, Alan T1 - Vorarlberg Referendum T2 - 1914-1918 online. International encyclopedia of the First World War Y1 - 2016 ER - TY - JOUR A1 - Duden, Antje T1 - Zum Lernen von Organisationen JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2016 VL - 15. Jg. IS - H. 2 SP - 3 EP - 19 ER - TY - JOUR A1 - Kriz, Willy Christian A1 - Auchter, Eberhard T1 - 10 Years of evaluation research into gaming simulation for german entrepreneurship and a new study on its long-term effects JF - Simulation & Gaming. An Interdisciplinary Journal of Theory, Practice and Research KW - business administration skills KW - business plan preparation skills KW - debriefing KW - entrepreneurial attitudes KW - entrepreneurship education KW - game-based competition KW - gender effects KW - learning and motivation effects KW - logic model KW - long-term effects KW - management simulation KW - startup simulation games KW - theory-based evaluation Y1 - 2016 U6 - http://dx.doi.org/10.1177/1046878116633972 SN - 1046-8781 SN - 1552-826X VL - Jg. 47 IS - H. 2 SP - 179 EP - 205 ER - TY - JOUR A1 - Kepplinger, Peter A1 - Huber, Gerhard A1 - Petrasch, Jörg T1 - Field testing of demand side management via autonomous optimal control of a domestic hot water heater JF - Energy and Buildings Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.enbuild.2016.06.021 SN - 03787788 VL - o.Jg. IS - Bd. 127 SP - 730 EP - 735 ER - TY - CHAP A1 - Weber, Wolfgang ED - Proske, Wolfgang T1 - Anton Plankensteiner: Gegen 'Niggertänze und Kinokitsch' T2 - NS-Belastete aus dem Bodenseeraum Y1 - 2016 SP - 162 EP - 172 PB - Kugelberg Verlag CY - Gerstetten ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Die Figur des Beobachters in der Betriebswirtschaftslehre JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2016 VL - 15. Jg. IS - H. 2 SP - 95 EP - 115 ER - TY - JOUR A1 - Feilhauer, Thomas A1 - Sobotka, Martin T1 - DEF - a programming language agnostic framework and execution environment for the parallel execution of library routines JF - Journal of Cloud Computing Y1 - 2016 U6 - http://dx.doi.org/10.1186/s13677-016-0070-z SN - 2192-113X VL - 5. Jg. IS - 20 ER - TY - JOUR A1 - Breuer, Thomas A1 - Csiszar, Imre T1 - Measuring distribution model risk. Veröffentlichungsdatum Web: 9 October 2013 JF - Mathematical Finance KW - convex integral functional KW - Bregman distance KW - f-divergence KW - divergence preferences KW - generalized exponential family KW - maximum entropy principle KW - Multiple priors KW - Relative entropy Y1 - 2016 U6 - http://dx.doi.org/10.1111/mafi.12050 SN - 1467-9965 VL - 26. Jg. IS - H. 2 SP - 395 EP - 411 ER - TY - CHAP A1 - Gajdosova, Lenka A1 - Seyringer, Dana ED - Michalka, Miroslav ED - Vincze, Andrej T1 - Design of Si3N4 AWGS applying various photonics tools T2 - 19. Skola Vakuovej Techniky. Vakuum a nove materialy. Vacuum and new materials. Zbornik prispevkov. 9. - 12. November 2016. Strbske Pleso. Hotel Trigan Y1 - 2016 SP - 63 EP - 67 PB - Slovenska vakuova spolocnost u.a. CY - Bratislava ER - TY - CHAP A1 - Brezany, Peter A1 - Ludescher, Thomas A1 - Feilhauer, Thomas ED - Biljanovic, Petar ED - Butkovic, Zeljko ED - Skala, Karolj ED - Grbac, Tihana Galinac ED - Cicin-Sain, Marina ED - Sruk, Vlado ED - Ribaric, Slobodan ED - Gros, Stjepan ED - Vrdoljak, Boris ED - Mauher, Mladen ED - Tijan, Edvard ED - Lukman, Dino T1 - Towards a novel infrastructure for conducting high productive cloud-based scientific analytics T2 - Proceedings. 39th International Convention on Information and Communication Technology, Electronics and Microelectronics (MIPRO). May 30 - June 3, 2016. Opatija, Croatia Y1 - 2016 SP - 186 EP - 191 PB - MIPRO CY - Rijeka ER - TY - BOOK A1 - Dorn, Christian T1 - Lernen mit Leusel. Lernen unter Selbstkontrolle im Rahmen technologieunterstützter Wissensvermittlung T3 - Denkprozesse Publikationen Y1 - 2016 SN - 978-3-7392-2615-6 PB - Books on demand CY - Norderstedt ER - TY - BOOK A1 - Dorn, Christian T1 - Kommunikation. Eine pragmatisch-kompakte Einführung für soziale und andere Berufe ... T3 - Denkprozesse Publikationen Y1 - 2016 SN - 978-3-7386-4345-9 PB - Books on Demand CY - Norderstedt ER - TY - CHAP A1 - Schneider, Reinhard A1 - Öttl, Markus T1 - Zuverlässigkeit von Leistungselektronik in elektrifizierten Antriebssträngen: Zufall oder vorhersagbar? T2 - Brücken bauen – Perspektiven gestalten ... für Wirtschaft, Hochschule und Öffentlichkeit. 30. und 31. März 2016. Fachhochschule des BFI Wien. Tagungsband. 10. Forschungsforum der österreichischen Fachhochschulen Y1 - 2016 PB - Fachhochschule des BFI Wien GmbH CY - Wien ER - TY - CHAP A1 - Finck, Steffen T1 - Analysis of simple pattern search on the noisy sphere model T2 - 2016 IEEE Congress on Evolutionary Computation (CEC). 24-29 July 2016. Vancouver, Canada Y1 - 2016 SP - 4313 EP - 4320 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Böhler, Doris T1 - Lernen auf Augenhöhe - Studierende der Sozialen Arbeit gemeinsam mit AdressatInnen JF - SiO Sozialarbeit in Oesterreich. Zeitschrift für Soziale Arbeit, Bildung und Politik Y1 - 2016 VL - 50. Jg. IS - H. 3 SP - 10 EP - 14 ER - TY - CHAP A1 - Alton-Scheidl, Roland ED - Aigner, Silvie ED - Ecker, Berthold T1 - Das Orakel hat uns fest im Griff. DELPHI DIGITAL 1991 und 2015: zwei Entwürfe zur Emanzipation der digitalen Gesellschaft T2 - Margot Pilz - Meilensteine/Milestones. Von der performativen Fotografie zur digitalen Feldforschung Y1 - 2016 SN - 978-3-11-045841-1 SP - 134 EP - 141 PB - De Gruyter CY - Berlin u.a. ER - TY - CHAP A1 - Mayer, Horst O. A1 - Grosch, Marco ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Digital Signage. Wirksamkeit und die Frage nach dem Inhalt T2 - Design2product. Beiträge zur empirischen Designforschung. Datenvisualisierung Y1 - 2016 SP - 53 EP - 69 PB - Bucher Verlag CY - Hohenems u.a. ER - TY - CHAP A1 - Weber, Wolfgang ED - Proske, Wolfgang T1 - Alfred Lusser: 'Ich habe nicht verstanden, dass jemand gegen die Regierung sein kann...' T2 - NS-Belastete aus dem Bodenseeraum Y1 - 2016 SP - 128 EP - 138 PB - Kugelberg Verlag CY - Gerstetten ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Manahl, Werner ED - Kaneda, Toshiyuki ED - Kanegae, Hidehiko ED - Toyoda, Yusuke ED - Rizzi, Paola T1 - Understanding and changing systems through hybrid simulation game design methods in educational contexts T2 - Simulation and gaming in the network society Y1 - 2016 SN - 978-981-10-0574-9 SN - 978-981-10-0575-6 SP - 79 EP - 93 PB - Springer CY - Singapore ER - TY - JOUR A1 - Wilms, Falko E. P. A1 - Meusburger, Magdalena T1 - Das CIRCU JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2016 VL - 15. Jg. IS - H. 1 SP - 95 EP - 112 ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Meusburger, Magdalena ED - Wilms, Falko E. P. T1 - Das Circu T2 - Das CIRCU Y1 - 2016 SP - 11 EP - 37 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - JOUR A1 - Meusburger, Magdalena A1 - Antonites, Alexander Josef T1 - Assessing antecedents of entrepreneurial activities of academics at south african universities JF - International Journal of Innovation Management Y1 - 2016 U6 - http://dx.doi.org/10.1142/S1363919616500584 SN - 1363-9196 VL - Jg. 20 IS - H. 6 ER - TY - CHAP A1 - Weber, Heidi A1 - Mateus, Americo A1 - Cruz Rodriguez, Antonio ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Ins Gesicht geschrieben – Emotionen erkennen und bewerten T2 - Design2product. Beiträge zur empirischen Designforschung. Datenvisualisierung Y1 - 2016 SP - 109 EP - 132 PB - Bucher Verlag CY - Hohenems u.a. ER - TY - CHAP A1 - Moser, Sarah A1 - Luxenberger, Wolfgang T1 - Soziale Unterstützung als relevanter Einflussfaktor bei älteren Erwachsenen mit Altersschwerhörigkeit T2 - 60. Österreichischer HNO-Kongress. Abstractband. Diagnostischer & therapeutischer Fortschritt in der HNO-Heilkunde. 14. – 18. September 2016. Congress Center Villach Y1 - 2016 PB - HNO CY - Wien ER - TY - JOUR A1 - Weinstein, Barbara E. A1 - Sirow, Lynn A1 - Moser, Sarah T1 - Relating hearing aid use to social and emotional loneliness in older adults JF - American Journal of Audiology Y1 - 2016 U6 - http://dx.doi.org/10.1044/2015_AJA-15-0055 VL - 25. Jg. IS - H. 1 SP - 54 EP - 61 ER - TY - CHAP A1 - Lipinski, Wojciech A1 - Haussener, Sophia A1 - Petrasch, Jörg T1 - Continuum radiative heat transfer modeling in multi-component anisotropic media in the limit of geometrical optics T2 - Eurotherm Conference No. 105: Computational Thermal Radiation in Participating Media V Y1 - 2016 U6 - http://dx.doi.org/10.1088/1742-6596/676/1/012015 VL - o.Jg. ER - TY - JOUR A1 - Weber, Heidi A1 - Cruz Rodriguez, Antonio A1 - Mateus, Americo T1 - Innovation gestalten. Design Thinking als Schlüssel in die Zukunft JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2016 SN - 1610-8914 VL - 15. Jg. IS - H. 2 SP - 75 EP - 93 ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Manahl, Werner ED - Schwägele, Sebastian ED - Zürn, Birgit ED - Bartschat, Daniel ED - Trautwein, Friedrich T1 - Design of Simulation Games for systems management education. A case example from the curriculum at University of Applied Sciences Vorarlberg (FHV) T2 - Planspiele - Vernetzung gestalten. Forschungsergebnisse und Praxisbeispiele für morgen KW - Business & Economics / General Y1 - 2016 SN - 978-3-7412-2522-2 SP - 69 EP - 92 PB - Books on demand CY - Norderstedt ER - TY - RPRT A1 - McCormick Williams, Michael T1 - Connecting education and enterprise: the need for transformative professionalism among University of Applied Sciences lecturers in Europe T3 - Arbeitsbericht Department Sozial- und Organisationswissenschaften - 2 Y1 - 2016 PB - FH Vorarlberg CY - o.O. ER - TY - CHAP A1 - Weber, Wolfgang ED - Proske, Wolfgang T1 - Josef Vallaster: Ein kleines Rad, das größere am Laufen hielt T2 - NS-Belastete aus dem Bodenseeraum KW - +SAE 177 NAT KW - +SAE 186 V KW - Nationalsozialismus : Geschichte KW - Vorarlberg : Geschichte Y1 - 2016 SN - 978-3-945893-04-3 SP - 272 EP - 285 PB - Kugelberg Verlag CY - Gerstetten ER - TY - CHAP A1 - Mayer, Horst O. A1 - Schöller, Marion ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Food Truck - Welches Angebot für Vorarlberg? T2 - Design2product. Beiträge zur empirischen Designforschung. Datenvisualisierung Y1 - 2016 SP - 89 EP - 107 PB - Bucher Verlag CY - Hohenems u.a. ER - TY - CHAP A1 - Kriz, Willy Christian ED - Geramanis, Olaf ED - Hermann, Kristina T1 - Systemkompetenz für die Führung in Veränderungsprozessen T2 - Führen in ungewissen Zeiten. Impulse, Konzepte und Praxisbeispiele Y1 - 2016 SN - 978-3-658-11226-4 SN - 978-3-658-11227-1 SP - 49 EP - 66 PB - Springer Gabler CY - Wiesbaden ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Meusburger, Magdalena ED - Wilms, Falko E. P. T1 - Die Beobachtung des Circu T2 - Das CIRCU Y1 - 2016 SP - 61 EP - 83 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Manahl, Werner ED - Monaghan, Michael T1 - SysTeamsChange - simulation game for leadership and change management T2 - Congress Proceedings. Australasian Simulation Congress. 26-29 September 2016. Melbourne Convention and Exhibition Centre. Victoria, Australia Y1 - 2016 PB - Simulation Australasia CY - Rundle Mall ER - TY - JOUR A1 - Aguilo-Aguayo, Noemi A1 - Amann, Peter A1 - Espineira, Pablo Pena A1 - Petrasch, Jörg A1 - Bechtold, Thomas T1 - X-ray micro tomography of three-dimensional embroidered current collectors for lithium-ion batteries JF - Journal of Power Sources KW - Tomography KW - Batteries KW - Electrodes KW - Li KW - Porous KW - Textile Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.jpowsour.2015.10.039 SN - 0378-7753 VL - o.Jg. IS - Bd. 306 SP - 826 EP - 831 ER - TY - JOUR A1 - Li, Like A1 - Chen, Chen A1 - Singh, Abhishek A1 - Rahmatian, Nima A1 - AuYeung, Nick A1 - Randhir, Kelvin A1 - Mei, Renwei A1 - Klausner, James F. A1 - Hahn, David W. A1 - Petrasch, Jörg T1 - A transient heat transfer model for high temperature solar thermochemical reactors JF - International Journal of Hydrogen Energy KW - Heat transfer KW - Lattice Boltzmann KW - Monte-Carlo ray tracing KW - Solar reactor KW - Thermochemical fuel production Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.ijhydene.2015.11.079 SN - 0360-3199 VL - 41. Jg. IS - H. 4 SP - 2307 EP - 2325 ER - TY - RPRT A1 - Meusburger, Magdalena T1 - Der Weg zur unternehmerischen Universität T3 - Arbeitsberichte des Competence Center of Communication & Collaboration - 2 Y1 - 2016 PB - FH Vorarlberg CY - o.O. ER - TY - RPRT A1 - Wilms, Falko E. P. T1 - Das CIRCU-Modell T3 - Arbeitsbericht Department Sozial- und Organisationswissenschaften - 3 Y1 - 2016 PB - FH Vorarlberg CY - o.O. ER - TY - RPRT A1 - Wilms, Falko E. P. T1 - Betriebswirtschaftliche Anwendungen der Notation von George Spencer-Brown T3 - Arbeitsberichte des Competence Center of Communication & Collaboration - 1 Y1 - 2016 PB - FH Vorarlberg CY - o.O. ER - TY - BOOK ED - Stifter, Christian H. ED - Weber, Wolfgang T1 - Aspekte zur deutschnationalen und nationalsozialistischen Vergangenheit der Wiener Universitäten und deren rechtskonservatives Erbe nach 1945 T3 - Zeitgeschichte, 2016/3 Y1 - 2016 PB - StudienVerlag CY - Innsbruck u.a. ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Auchter, Eberhard A1 - Wittenzellner, Helmut ED - Schwägele, Sebastian ED - Zürn, Birgit ED - Bartschat, Daniel ED - Trautwein, Friedrich T1 - Langfristige Effekte eines planspielbasierten Gründerwettbewerbs. Ergebnisse einer Nachbefragungsstudie T2 - Planspiele - Vernetzung gestalten. Forschungsergebnisse und Praxisbeispiele für morgen KW - Business & Economics / General Y1 - 2016 SN - 978-3-7412-2522-2 SP - 13 EP - 30 PB - Books on demand CY - Norderstedt ER - TY - CHAP A1 - Kriz, Willy Christian ED - Ameln, Falko von ED - Kramer, Josef T1 - Organisationsentwicklungsprozesse mit Planspielen steuern und begleiten T2 - Organisationen in Bewegung bringen. Handlungsorientierte Methoden für die Personal-, Team- und Organisationsentwicklung Y1 - 2016 SP - 332 EP - 334 PB - Springer CY - Berlin u.a. ET - 2., überarb. Aufl. ER - TY - BOOK ED - Meusburger, Magdalena ED - Wilms, Falko E. P. T1 - Das CIRCU. Konzept - Anwendung - Beobachtung T3 - Wandel und Kontinuität in Organisationen - 17 KW - +AWD 520 OuW KW - Fachhochschule Vorarlberg : Wandel und Kontinuität in Organisationen KW - +SPC 600 KW - +WBB 642 KW - Kommunikation : Sozialpsychologie KW - Teamwork Y1 - 2016 SN - 978-3-86573-987-2 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Meusburger, Magdalena ED - Meusburger, Magdalena ED - Wilms, Falko E. P. T1 - Der Weg zur unternehmerischen Universität T2 - Das CIRCU T2 - Wandel und Kontinuität in Organisationen, 17 Y1 - 2016 SP - 39 EP - 59 PB - Wissenschaftlicher Verlag Berlin CY - Berlin ER - TY - CHAP A1 - Ho, Stephen A1 - Domke, Matthias A1 - Roper, David A1 - Huber, Heinz A1 - Herman, Peter R. T1 - Femtosecond laser quantized structuring in thin SiOx film. Paper STh3Q.4 T2 - Conference on Lasers and Electro-Optics (2016). CLEO: Science and Innovations. San Jose, California United States. 5–10 June 2016 KW - Femtosecond phenomena KW - Laser materials processing KW - nanostructures KW - Subwavelength structures Y1 - 2016 PB - Optical Society of America ER - TY - CHAP A1 - Weinstein, Barbara E. A1 - Moser, Sarah A1 - Sirow, Lynn T1 - Correlates of hearing help seeking and hearing aid outcome among first time hearing aid users with age related hearing loss T2 - HeAL 2016. Hearing Across the Lifespan. June 2-4, 2016. Cernobbio (Como Lake), Italy. Program Y1 - 2016 PB - NHS u.a. CY - Cernobbio ER - TY - JOUR A1 - Szabo, Anna A1 - Unterkofler, Karl A1 - Mochalski, Pawel A1 - Jandacka, Martin A1 - Ruzsanyi, Vera A1 - Szabo, Gabor A1 - Arpad Mohacsi, A1 - Teschl, Susanne A1 - Teschl, Gerald A1 - King, Julian T1 - Modeling of breath methane concentration profiles during exercise on an ergometer JF - Journal of Breath Research Y1 - 2016 U6 - http://dx.doi.org/10.1088/1752-7155/10/1/017105 SN - 1752-7163 VL - 10. Jg. IS - H. 1 ER - TY - JOUR A1 - Filipiak, Wojciech A1 - Mochalski, Pawel A1 - Filipiak, Anna A1 - Ager, Clemens A1 - Cumeras, Raquel A1 - Davis, Cristina E. A1 - Agapiou, Agapios A1 - Unterkofler, Karl A1 - Troppmair, Jakob T1 - A compendium of volatile organic compounds (VOCs) released by human cell lines JF - Current Medicinal Chemistry Y1 - 2016 VL - 23. Jg. IS - H. 20 SP - 2112 EP - 2131 ER - TY - THES A1 - Hellwig, Michael Lorenz T1 - Analysis of mutation strength adaption within evolution strategies on the ellipsoid model and methods for the treatment of fitness noise Y1 - 2016 U6 - http://dx.doi.org/10.18725/OPARU-4253 PB - Universität CY - Ulm ER - TY - JOUR A1 - Kramer, Christian A1 - Mochalski, Pawel A1 - Unterkofler, Karl A1 - Agapiou, Agapios A1 - Ruzsanyi, Veronika A1 - Liedl, Klaus R. T1 - Prediction of blood:air and fat:air partition coefficients of volatile organic compounds for the interpretation of data in breath gas analysis JF - Journal of Breath Research Y1 - 2016 U6 - http://dx.doi.org/10.1088/1752-7155/10/1/017103 SN - 1752-7163 VL - 10. Jg. IS - H. 1 ER - TY - JOUR A1 - Mochalski, Paweł A1 - Unterkofler, Karl T1 - Quantification of selected volatile organic compounds in human urine by gas chromatography selective reagent ionization time of flight mass spectrometry (GC-SRI-TOF-MS) coupled with head-space solid-phase microextraction (HS-SPME) JF - Analyst Y1 - 2016 U6 - http://dx.doi.org/10.1039/C6AN00825A SN - 1364-5528 VL - 141. Jg. IS - H. 15 SP - 4796 EP - 4803 ER - TY - JOUR A1 - Hellwig, Michael A1 - Beyer, Hans-Georg T1 - Mutation strength control via meta evolution strategies on the ellipsoid model JF - Theoretical Computer Science KW - Ellipsoid model KW - Evolution strategies KW - Meta evolution strategies KW - Mutation strength adaptation Y1 - 2016 U6 - http://dx.doi.org/10.1016/j.tcs.2015.12.011 SN - 0304-3975 VL - o.Jg. IS - Bd. 623 SP - 160 EP - 179 ER - TY - JOUR A1 - Hellwig, Michael A1 - Arnold, Dirk V. T1 - Comparison of constraint-handling mechanisms for the (1,λ)-ES on a simple constrained problem JF - Evolutionary Computation Y1 - 2016 U6 - http://dx.doi.org/10.1162/EVCO_a_00139 SN - 1063-6560 VL - 24. Jg. IS - H. 1 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Kategorienfehler können vermieden werden. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2016 UR - http://www.trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/24434-problemloesungsprozesse-initiieren-kategorienfehler-koennen-vermieden-werden VL - o.Jg. IS - Nr. 88 ER - TY - CHAP A1 - Doshi, Natasha ED - Psonder, Tanja ED - Casey, Annette ED - Tatzl, Dietmar ED - Millward-Sadler, Adrian ED - Meixner, Karen T1 - English for intercultural awareness - a practical approach T2 - Teaching ESP in Higher Education. Examples from evidence-based practice. 8th Austrian AUS Language Instructor's Conference. Conference Proceedings Y1 - 2016 UR - http://bizepaper.fh-joanneum.at/eBooks/Teaching%20ESP%20in%20Higher%20Education.pdf SN - 978-3-902103-64-2 SN - 978-3-902103-65-9 SP - 14 EP - 20 PB - FH Joanneum Gesellschaft mbH Publishing CY - Graz ER - TY - JOUR A1 - Wittenzellner, Helmut A1 - Schmidt, Herbert A1 - Kriz, Willy C. T1 - Strategy4Innovators-training without software? The revised concept of the Board Game SysTeamsRybi – realize your business ideas! JF - Developments in Business Simulation and Experiential Learning Y1 - 2016 UR - https://journals.tdl.org/absel/index.php/absel/article/view/3057 VL - 43. Jg. ER - TY - BOOK A1 - Geser-Engleitner, Erika T1 - Bettelnde Notreisende in Vorarlberg. Eine empirische Untersuchung Y1 - 2016 UR - https://vorarlberg.at/documents/21336/82158/Bettelnde+Notreisende+in+Vorarlberg.pdf/397eceff-3753-4435-a9ab-0f453b40fb8e?version=1.0 PB - Amt der Vorarlberger Landesregierung CY - Bregenz ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Gestaltung reflexiver Kommunikationen. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2016 UR - http://www.trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/24584-problemloesungsprozesse-initiieren-gestaltung-reflexiver-kommunikationen VL - o.Jg. IS - Nr. 89 ER - TY - CHAP A1 - Seyringer, Dana A1 - Burtscher, Catalina A1 - Piredda, Giovanni A1 - Prasad, Amrita A1 - Zehetner, Johann T1 - The Night of Science. Optics and photonics for all T2 - The European Conference on Technology in the Classroom 2016. Official Conference Proceedings Y1 - 2016 UR - http://25qt511nswfi49iayd31ch80-wpengine.netdna-ssl.com/wp-content/uploads/papers/ectc2016/ECTC2016_25517.pdf SP - 13 EP - 25 PB - International Academic Forum CY - Nagoya ER - TY - CHAP A1 - Fredersdorf, Frederic T1 - Das Vorarlberger Lehrlingsmodell aus Sicht seiner Zielgruppen. T2 - Berufsbildung, eine Renaissance? Motor für Innovation, Beschäftigung, Teilhabe, Aufstieg, Wohlstand,... 5. Österreichische Berufsbildungsforschungskonferenz, 7.-8.7.2016, Steyr/OÖ. Abstracts. KW - Lehre und Matura KW - Survey KW - Vorarlberg KW - Vorarlberger Lehrlingsmodell KW - Zielgruppenbefragung Y1 - 2016 ER - TY - JOUR A1 - Beyer, Hans-Georg A1 - Hellwig, Michael T1 - The dynamics of cumulative step size adaptation on the ellipsoid model JF - Evolutionary Computation Y1 - 2016 U6 - http://dx.doi.org/10.1162/EVCO_a_00142 SN - 1063-6560 VL - 24. Jg. IS - H. 1 SP - 25 EP - 57 ER - TY - CHAP A1 - Hellwig, Michael A1 - Beyer, Hans-Georg ED - Handl, Julia ED - Hart, Emma ED - Lewis, Peter R. ED - Lopez-Ibanez, Manuel ED - Ochoa, Gabriela ED - Paechter, Ben T1 - Evolution under strong noise. A self-adaptive evolution strategy can reach the lower performance bound - the pcCMSA-ES T2 - Parallel Problem Solving from Nature – PPSN XIV. 14th International Conference, Edinburgh, UK, September 17-21, 2016. Proceedings Y1 - 2016 SN - 978-3-319-45823-6 SP - 26 EP - 36 PB - Springer International Publishing CY - Cham ER - TY - CHAP A1 - Unterkofler, Karl A1 - Teschl, Susanne T1 - On the influence of inhaled volatile organic compounds (VOCs) on exhaled VOCs concentrations T2 - Brücken bauen – Perspektiven gestalten ... für Wirtschaft, Hochschule und Öffentlichkeit. 30. und 31. März 2016. Fachhochschule des BFI Wien. Tagungsband. 10. Forschungsforum der österreichischen Fachhochschulen Y1 - 2016 PB - Fachhochschule des BFI Wien GmbH CY - Wien ER - TY - CHAP A1 - Weber, Heidi A1 - Cruz Rodriguez, Antonio A1 - Mateus, Americo ED - Duarte, Emilia ED - Duarte, Carlos ED - Rodrigues, Fernando Carvalho T1 - Emotion and mood in Design Thinking T2 - Proceedings of the Design Doctoral Conference 2016. IADE-U - Portugal. 16 - 17.06.2016 Y1 - 2016 UR - http://unidcom.iade.pt/ddc16/wp-content/uploads/2016/07/Proceedings-e-Book.pdf SP - 65 EP - 72 PB - IADE – Creative University CY - o.O. ER - TY - JOUR A1 - Horn, Sierk A. A1 - Cross, Adam R. T1 - Japanese production networks in India BT - spatial distribution, agglomeration and industry effects JF - Asia Pacific Business Review N2 - This paper examines the determinants of subnational location choice of Japanese multinational enterprises (JMNEs) in India to investigate whether or not conventional investment behaviour as ‘foot-loose’ and one-off investments has given way to an agglomeration logic as Japanese foreign direct investment has intensified. Using geographic information system analysis of investment project numbers, we find that Japanese MNE behaviour in India is evolving, with complementing but complex subnational interactions of economic, institutional and infrastructure factors serving as strong determinants of location choice consistently across key phases of India’s liberalization. We argue that Japanese investment decisions in India have followed a self-reinforcing dynamic whereby prior investments indeed attract further investment. Y1 - 2016 U6 - http://dx.doi.org/10.1080/13602381.2016.1168625 VL - 22 IS - 4 SP - 612 EP - 640 ER - TY - JOUR A1 - Horn, Sierk A. T1 - The social and psychological costs of peer review BT - stress and coping with manuscript rejection JF - Journal of management inquiry Y1 - 2016 U6 - http://dx.doi.org/10.1177/1056492615586597 VL - 25. Jg. IS - H. 1 SP - 11 EP - 26 ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Rosmann, Sabrina A1 - Marinov, Marin T1 - Using motion capturing sensor systems for natural user interface T2 - 2016 XXV International Scientific Conference Electronics (ET). 12-14 Sept. 2016 KW - 3D graphics KW - Blender KW - Computers KW - graphical user interfaces KW - Graphics KW - Human computer interaction KW - Kinect for Windows KW - MCSS KW - Microsoft Kinect KW - Motion Capturing KW - motion capturing sensor systems KW - motion compensation KW - natural sensor KW - natural user interface KW - Protocols KW - software packages KW - Three-dimensional displays KW - User interface KW - virtual reality KW - VR environments KW - Windows Y1 - 2016 SP - 116 EP - 119 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Lorünser, Daniela ED - Fredersdorf, Frederic T1 - Ambulante lebensweltorientierte Betreuung T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 41 EP - 50 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Lorünser, Daniela ED - Fredersdorf, Frederic T1 - Prekäre Lebenswelten in Vorarlberg T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 19 EP - 26 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Fredersdorf, Frederic ED - Kern, Thomas ED - Kastner, Johann ED - Jungwirth, Mario ED - Mayr, Herwig ED - Rau, Christiane T1 - Die Caritas aus Sicht ihrer Spender/innen T2 - 9. Forschungsforum der Österreichischen Fachhochschulen. Wegbereiter - Karrierepfade durch ein Fachhochschulstudium. FH Oberösterreich, Campus Hagenberg. 8. und 9. April 2015. Tagungsband KW - Caritas KW - Image KW - Imageanalyse KW - Spenden KW - Spendenmotivation KW - Spendenmotive Y1 - 2015 PB - FH OÖ Forschungs & Entwicklungs GmbH CY - Wels ER - TY - CHAP A1 - Kempter, Guido A1 - Filkov, Rumen A1 - Künz, Andreas A1 - Sun, Jianing A1 - Daw, Walid A1 - Frenz, Hans-Georg A1 - Frey, Siegfried ED - Jost, Patrick ED - Künz, Andreas T1 - Vermittlung von manuellen Arbeitstätigkeiten durch virtuelle TutorInnen T2 - Digitale Medien in Arbeits- und Lernumgebungen. Beiträge zum Usability Day XIII. 12. Juni 2015 Y1 - 2015 SP - 102 EP - 108 PB - Pabst Science Publ. CY - Lengerich ER - TY - JOUR A1 - Domke, Matthias A1 - Felsl, Dominik A1 - Rapp, Stephan A1 - Sotrop, Jürgen A1 - Huber, Heinz P. A1 - Schmidt, Michael T1 - Evidence of pressure waves in confined laser ablation JF - Journal of Laser Micro/Nanoengineering Y1 - 2015 U6 - http://dx.doi.org/10.2961/jlmn.2015.02.0002 SN - 1880-0688 VL - 10. Jg. IS - H. 2 SP - 119 EP - 123 ER - TY - RPRT A1 - Geser-Engleitner, Erika A1 - Reiner, Julia T1 - Evaluation des Pilotprojekts "IMPULS 2014". Ergebnisbericht Y1 - 2015 ER - TY - CHAP A1 - Ritter, Walter A1 - Kempter, Guido A1 - Werner, Tobias ED - Antona, Margherita ED - Stephanidis, Constantine T1 - User-acceptance of latency in touch interactions T2 - Universal Access in Human-Computer Interaction. Access to interaction. 9th International Conference, UAHCI 2015. Held as part of HCI International 2015. Los Angeles, CA, USA, August 2–7, 2015. Proceedings. Part II KW - Acceptance KW - Gesture recognition KW - Interaction KW - Latency KW - Touch Y1 - 2015 SN - 978-3-319-20680-6 SP - 139 EP - 147 PB - Springer CY - Cham u.a. ER - TY - RPRT A1 - Geser-Engleitner, Erika A1 - Reiner, Julia T1 - Sturzprävention mit dem OTAGO-Übungsprogramm. Dokumentation und Evaluation des Pilotprojekts zur Einführung des OTAGO-Übungsprogramms in Vorarlberg. Endbericht. Y1 - 2015 ER - TY - JOUR A1 - Hefel, Johanna T1 - Klinische Soziale Arbeit und Ausbildung in Österreich – eine Momentaufnahme JF - Klinische Sozialarbeit. Zeitschrift für psychosoziale Praxis und Forschung Y1 - 2015 VL - 11. Jg. IS - H. 3 SP - 14 EP - 15 ER - TY - CHAP A1 - Mayer, Horst O. ED - Jost, Patrick ED - Künz, Andreas T1 - Lernzielentwicklung und Lernzielevaluation im eLearning T2 - Digitale Medien in Arbeits- und Lernumgebungen. Beiträge zum Usability Day XIII. 12. Juni 2015 Y1 - 2015 SP - 48 EP - 53 PB - Pabst Science Publ. CY - Lengerich ER - TY - CHAP A1 - Pilsan, Horatiu A1 - Amann, Robert T1 - Codegenerierung - Was man damit (nicht) machen kann. Varianten, Möglichkeiten und Einschränkungen T2 - Tagungsband. Embedded Software Engineering Kongress 2015. 30. November bis 4. Dezember 2015, Sindelfingen Y1 - 2015 SN - 978-3-8343-2418-4 SP - 61 EP - 66 PB - Vogel CY - Würzburg ER - TY - CHAP A1 - Werner, Tobias ED - Jost, Patrick ED - Künz, Andreas T1 - Einflüsse zusätzlichen taktilen Feedbacks auf die Lernfähigkeit an Touchscreens T2 - Digitale Medien in Arbeits- und Lernumgebungen. Beiträge zum Usability Day XIII. 12. Juni 2015 Y1 - 2015 SP - 210 EP - 217 PB - Pabst Science Publ. CY - Lengerich ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Hense, Jan Ulrich ED - Blötz, Ulrich T1 - Evaluation und Qualitätssicherung von Planspielen T2 - Planspiele und Serious Games in der beruflichen Bildung. Auswahl, Konzepte, Lernarrangements, Erfahrungen - Aktueller Katalog für Planspiele und Serious Games 2015 Y1 - 2015 SP - 207 EP - 238 PB - Bertelsmann CY - Bielefeld ET - 5., überarb. Aufl. ER - TY - CHAP A1 - Simma, Armin A1 - Eppler, Jeremias A1 - Lang, Bernhard ED - Abouzakhar, Nasser T1 - Hands-on learning of computer security. A cost-effective laboratory infrastructure based on virtualization software T2 - Proceedings of the 14th European Conference on Cyber Warfare and Security. University of Hertfordshire Hatfield, UK. 2-3 July 2015. ECCWS 2015 Y1 - 2015 SN - 978-1-910810-28-6 SP - 276 EP - 285 PB - ACPI CY - Reading ER - TY - CHAP A1 - Lechner, Verena A1 - Weidmann, Karl Heinz A1 - Mayer, Horst O. ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Visualisierung der Datenbank-Performance durch die methodische Verknüpfung von Grundlagen der Formwahrnehmung mit den Prinzipien des Radardiagramms T2 - design2product. Beiträge zur empirischen Designforschung. Methoden der Designforschung Y1 - 2015 SP - 148 EP - 168 PB - Bucher CY - Hohenems u.a. ER - TY - BOOK ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Design2product. Beiträge zur empirischen Designforschung. Methoden der Designforschung T3 - Design2product, 5 Y1 - 2015 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Lechner, Verena A1 - Weidmann, Karl-Heinz ED - Antona, Margherita ED - Stephanidis, Constantine T1 - Visualizing database-performance through shape, reflecting the development opportunities of radar charts T2 - Universal Access in Human-Computer Interaction. Access to today's technologies. 9th International Conference, UAHCI 2015. Held as part of HCI International 2015. Los Angeles, CA, USA, August 2-7, 2015. Proceedings. Part I Y1 - 2015 U6 - http://dx.doi.org/10.1007/978-3-319-20678-3_44 SP - 455 EP - 463 PB - Springer CY - Cham u.a. ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Roux, Pascale A1 - Rebitzer, Fabian A. ED - Fredersdorf, Frederic T1 - Wohnbedarf im Alter T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 173 EP - 182 PB - Springer VS CY - Wiesbaden ER - TY - RPRT A1 - Geser-Engleitner, Erika A1 - Reiner, Julia T1 - Familienkonzept Hohenems. Ziele und Maßnahmen. [Forschungsbericht] Y1 - 2015 ER - TY - CHAP A1 - Zehetner, Johann A1 - Schmidmayr, David A1 - Piredda, Giovanni A1 - Kasemann, Stephan A1 - Matylitskaya, Volha A1 - Lucki, Michal ED - Vajda, Jan ED - Jamnicky, Igor T1 - Laser generated micro- and nanostructures and the transfer to polymers for experimental use T2 - Proceedings of the 21st International Conference on Applied Physics of Condensed Matter (APCOM 2015) and of the Scientific Conference on Advanced Fast Reactors. June 24 - 26, 2015. Strbske Pleso, Slovak Republic Y1 - 2015 SP - 282 EP - 285 PB - Nakl. STU CY - Bratislava ER - TY - BOOK A1 - Dorn, Christian T1 - Mediale Sozialisation und eEducation. Neue Medien - Neue Menschen - Neue Didaktik. Eine Konzeptentwicklung basierend auf der Analyse menschlicher Bewusstseins- und Handlungsstrukturen vor dem Hintergrund einer immer authentischer werdenden Medialität T3 - Denkprozesse Publikationen Y1 - 2015 SN - 978-3-7347-8048-6 PB - Books on Demand CY - Norderstedt ER - TY - CHAP A1 - Jost, Patrick ED - Jost, Patrick ED - Künz, Andreas T1 - Nutzungserlebnis gestalten - emotionales Erleben interaktiver Arbeitsanwendungen T2 - Digitale Medien in Arbeits- und Lernumgebungen. Beiträge zum Usability Day XIII. 12. Juni 2015 Y1 - 2015 SP - 136 EP - 147 PB - Pabst Science Publ. CY - Lengerich ER - TY - BOOK A1 - Duden, Antje T1 - Lernen in Organisationen. Lernen, Organisation, Führung, Kommunikation. Y1 - 2015 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Kepplinger, Peter A1 - Huber, Gerhard A1 - Petrasch, Jörg T1 - Autonomous optimal control for demand side management with resistive domestic hot water heaters using linear optimization T2 - E-nova 2013. Sustainable buildings: supply - evaluation - integration KW - Data mining KW - Demand side management KW - Domestic hot water heater KW - Optimization Y1 - 2015 U6 - http://dx.doi.org/10.1016/j.enbuild.2014.12.016 VL - o.Jg. SP - 50 EP - 55 ER - TY - CHAP A1 - Hämmerle, Isabella A1 - Kempter, Guido ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Methoden in der Lichtwirkungsforschung T2 - design2product. Beiträge zur empirischen Designforschung. Methoden der Designforschung Y1 - 2015 SP - 205 EP - 235 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Domke, Matthias ED - Heisterkamp, Alexander ED - Herman, Peter R. ED - Meunier, Michel ED - Nolte, Stefan T1 - Conditions for random and periodic hole formations during surface ablation of silicon with ultrashort pulsed lasers T2 - Frontiers in Ultrafast Optics. Biomedical, Scientific, and Industrial Applications XV. 8–10 February 2015. San Francisco, California, United States Y1 - 2015 VL - 9355 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Fredersdorf, Frederic ED - Fredersdorf, Frederic T1 - Spendenmotivation und Werthaltungen gegenüber der Caritas Vorarlberg T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 155 EP - 163 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Fredersdorf, Frederic ED - Fredersdorf, Frederic T1 - Derzeitige Projektlage und Zukunft des FB SoWi T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 207 EP - 211 PB - Springer VS CY - Wiesbaden ER - TY - BOOK A1 - Dorn, Christian T1 - Salutogenese: Wie die Medialität die Kohärenz zerfrisst! Interdisziplinäre Psychosomatik: Medialität und Trauprädisposition aus Sicht der Medien- und Sozialpsychologie T3 - Denkprozesse Publikationen Y1 - 2015 SN - 978-3-7347-9558-9 SN - 3-7347-9558-3 PB - Books on Demand CY - Norderstedt ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Tragfähige Kommunikation benötigt Selbsterkenntnis. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2015 VL - o.Jg. IS - Nr. 87 ER - TY - CHAP A1 - Domke, Matthias A1 - Egle, Bernadette A1 - Piredda, Giovanni A1 - Fasching, Gernot A1 - Bodea, Marius A1 - Schwarz, Elisabeth ED - Roth, Stephan ED - Nakata, Yoshiki ED - Neuenschwander, Beat ED - Xu, Xianfan T1 - Controlling depth and distance of the hole formations at the bottom of laser-scribed trenches in silicon using fs-pulses T2 - Laser Applications in Microelectronic and Optoelectronic Manufacturing (LAMOM) XX. 9–12 February 2015. San Francisco, California, United States Y1 - 2015 VL - 9350 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Roux, Pascale ED - Fredersdorf, Frederic T1 - Lebensweltorientierte Alkoholprävention für Jugendliche T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 63 EP - 75 PB - Springer VS CY - Wiesbaden ER - TY - BOOK A1 - Dorn, Christian T1 - Digital Storytelling: Pädagogik und Therapie für medial sozialisierte Menschen. Erziehung - Bildung - Heilung T3 - Denkprozesse Publikationen Y1 - 2015 SN - 978-3-7347-9623-4 PB - Books on Demand CY - Norderstedt ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Lorünser, Daniela ED - Kern, Thomas ED - Kastner, Johann ED - Jungwirth, Mario ED - Mayr, Herwig ED - Rau, Christiane T1 - Auslandssemester im Karrierefokus – Evaluierung der Auslandssemester am Beispiel einer Hochschule T2 - 9. Forschungsforum der Österreichischen Fachhochschulen. Wegbereiter - Karrierepfade durch ein Fachhochschulstudium. FH Oberösterreich, Campus Hagenberg. 8. und 9. April 2015. Tagungsband Y1 - 2015 PB - FH OÖ Forschungs & Entwicklungs GmbH CY - Wels ER - TY - JOUR A1 - Böhler, Doris A1 - Randall, Matthew T1 - Flüchtlingssozialarbeit als menschenrechtsorientierte professionelle Arbeit. Eine notwendige Perspektive JF - Sozialarbeit in Österreich. SIO. Zeitschrift für Soziale Arbeit, Bildung und Politik Y1 - 2015 VL - o.Jg. IS - H. 3 SP - 14 EP - 17 ER - TY - CHAP A1 - Lorünser, Daniela A1 - Fredersdorf, Frederic ED - Fredersdorf, Frederic T1 - Kulturvermittlung in Vorarlberg T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 165 EP - 172 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Fredersdorf, Frederic ED - Fredersdorf, Frederic T1 - Der Forschungsbereich Sozial- und Wirtschaftswissenschaften an der FH Vorarlberg T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 9 EP - 15 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Böhler, Doris ED - Fredersdorf, Frederic T1 - European Research Institute for Social Work (ERIS) T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperation mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 51 EP - 59 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Seyringer, Dana A1 - Hodzic, Edin ED - Fedeli, Jean-Marc T1 - Calculation of accurate channel spacing of an AWG optical demultiplexer applying proportional method T2 - Integrated Photonics. Materials, devices, and applications III. 4-6 May 2015. Barcelona, Spain Y1 - 2015 PB - SPIE CY - Bellingham, Wash. ER - TY - JOUR A1 - Singh, Abhishek K. A1 - AuYeung, Nicholas J. A1 - Randhir, Kelvin A1 - Mishra, Rishi A1 - Allen, Kyle M. A1 - Petrasch, Jörg A1 - Klausner, James F. T1 - Thermal reduction of iron oxide under reduced pressure and implications on thermal conversion efficiency for solar thermochemical fuel production JF - Industrial & Engineering Chemistry Research Y1 - 2015 U6 - http://dx.doi.org/10.1021/ie504402x SN - 0888-5885 VL - 54. Jg. IS - H. 26 SP - 6793 EP - 6803 ER - TY - JOUR A1 - Ciesielski, Richard A1 - Comin, Alberto A1 - Handloser, Matthias A1 - Donkers, Kevin A1 - Piredda, Giovanni A1 - Lombardo, Antonio A1 - Ferrari, Andrea C. A1 - Hartschuh, Achim T1 - Graphene near-degenerate four-wave mixing for phase characterization of broadband pulses in ultrafast microscopy JF - Nano Letters Y1 - 2015 U6 - http://dx.doi.org/10.1021/acs.nanolett.5b00893 SN - 1530-6984 VL - Jg. 15 IS - H. 8 SP - 4968 EP - 4972 ER - TY - JOUR A1 - Partel, Stefan A1 - Dincer, Can A1 - Kasemann, Stephan A1 - Kieninger, Jochen A1 - Edlinger, Johannes A1 - Urban, Gerald T1 - Lift-off free fabrication approach for periodic structures with tunable nano gaps for interdigitated electrode arrays. Veröffentlichungsdatum Web: 1. Dezember 2015 JF - ACS Nano Y1 - 2015 U6 - http://dx.doi.org/10.1021/acsnano.5b06405 SN - 1936-0851 VL - 10 IS - 1 SP - 1086 EP - 1092 ER - TY - CHAP A1 - Seyringer, Dana A1 - Edlinger, Johannes ED - Vajda, Jan ED - Jamnicky, Igor T1 - Application of various tools to design, simulate and evaluate optical demultiplexers based on AWG T2 - Proceedings of the 21st International Conference on Applied Physics of Condensed Matter (APCOM 2015) and of the Scientific Conference on Advanced Fast Reactors. June 24 - 26, 2015. Strbske Pleso, Slovak Republic Y1 - 2015 SP - 322 EP - 326 PB - Nakl. STU CY - Bratislava ER - TY - BOOK A1 - Breuer, Thomas T1 - Capital shortfalls in SSM banks. How much progress has been made? In-depth analysis. Provided at the request of the Economic and Monetary Affairs Commitee Y1 - 2015 PB - Directorate-General for Internal Policies of the Union CY - Brussels ER - TY - CHAP A1 - Csiszar, Imre A1 - Breuer, Thomas ED - Nielsen, Frank ED - Barbaresco, Frederic T1 - An information geometry problem in mathematical finance T2 - Geometric science of information. Second International Conference, GSI 2015. Palaiseau, France, October 28 – 30, 2015. Proceedings KW - convex integral functional KW - I-divergence KW - Algorithm Analysis and Problem Complexity KW - Almost worst case densities KW - Artificial Intelligence (incl. Robotics) KW - Bregman distance KW - Computer Graphics KW - Discrete Mathematics in Computer Science KW - f-divergence KW - Image Processing and Computer Vision KW - Pattern Recognition KW - Payoff function KW - Pythagorean identity KW - Risk measure KW - Worst case density Y1 - 2015 SN - 978-3-319-25039-7 SN - 978-3-319-25040-3 SP - 435 EP - 443 PB - Springer CY - Cham u.a. ER - TY - JOUR A1 - Domke, Matthias A1 - Gavrilova, Anna A1 - Rapp, Stephan A1 - Frentzen, Matthias A1 - Meister, Joerg A1 - Huber, Heinz P. T1 - Time-resolved microscopy reveals the driving mechanism of particle formation during ultrashort pulse laser ablation of dentin-like ivory JF - Journal of Biomedical Optics Y1 - 2015 U6 - http://dx.doi.org/10.1117/1.JBO.20.7.076005 SN - 1083-3668 VL - 20. Jg. IS - H. 7 ER - TY - CHAP A1 - Burtscher, Catalina A1 - Lucki, Michal A1 - Seyringer, Dana ED - Pudis, Dusan ED - Lettrichova, Ivana ED - Kovac, Jaroslav T1 - Design, simulation and optimization of high channel optical splitters T2 - Proceedings of ADEPT. 3rd International Conference on Advances in Electronic and Photonic Technologies. Strbske Pleso, High Tatras, Slovakia, June 1-4, 2015 Y1 - 2015 SN - 978-80-554-1033-3 SP - 251 EP - 255 PB - University of Zilina CY - Zilina ER - TY - THES A1 - Domke, Matthias T1 - Transiente physikalische Mechanismen bei der Laserablation von dünnen Metallschichten. Bericht aus dem Lehrstuhl für Phototonische Technologien KW - +NPC 372 KW - +TEJ 630 KW - Laser KW - Materialbearbeitung, Metallbearbeitung Y1 - 2015 PB - Meisenbach CY - Bamberg ER - TY - CHAP A1 - Öttl, Markus A1 - Schneider, Reinhard T1 - Mission-specific aging of power modules T2 - Proceedings. PCIM Europe. International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management. Nuremberg, 19 - 21 May 2015 Y1 - 2015 SN - 978-3-8007-3924-0 SP - 1282 EP - 1287 PB - VDE-Verl. CY - Berlin u.a. ER - TY - CHAP A1 - Lucki, Michal A1 - Kraus, Stanislav A1 - Zeleny, Richard A1 - Zehetner, Johann A1 - Seyringer, Dana A1 - Latal, Jan Ulrich A1 - Perecar, Frantisek ED - Kalli, Kyriacos ED - Kanka, Jiri ED - Mendez, Alexis T1 - Investigation of optical thin films printed on the surface of facets of photonic crystal fibers T2 - Micro-structured and specialty optical fibres IV. 15–16 April 2015. Prague, Czech Republic Y1 - 2015 U6 - http://dx.doi.org/10.1117/12.2182203 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Domke, Matthias A1 - Wick, Sebastian A1 - Laible, Maike A1 - Rapp, Stephan A1 - Kuznetsova, Julia A1 - Homann, Christian A1 - Huber, Heinz P. A1 - Sroka, Ronald ED - Lilge, Lothar D. ED - Sroka, Ronald T1 - Investigations of the damage mechanisms during ultrashort pulse laser ablation of dental tissue T2 - Medical Laser Applications and Laser-Tissue Interactions VII. 21–23 June 2015. Munich, Germany Y1 - 2015 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Nöbauer, Brigitta ED - Blötz, Ulrich T1 - Den Lernerfolg mit Debriefing von Planspielen sichern T2 - Planspiele und Serious Games in der beruflichen Bildung. DVD-ROM: Fachbeiträge Y1 - 2015 PB - Bertelsmann CY - Bielefeld ET - 5., überarb. Aufl. ER - TY - JOUR A1 - Arzbacher, Stefan A1 - Amann, Peter A1 - Weidenfeller, Bernd A1 - Loerting, Thomas A1 - Ostermann, Alexander A1 - Petrasch, Jörg T1 - Tomography based numerical simulation of the demagnetizing field in soft magnetic composites JF - Journal of Applied Physics Y1 - 2015 U6 - http://dx.doi.org/10.1063/1.4917490 SN - 0021-8979 VL - o.Jg. IS - Bd. 117, H. 16 ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Manhart, Wilfried A1 - Chen, Stefanie A1 - Lorünser, Daniela ED - Fredersdorf, Frederic T1 - Indien – potenzieller Exportmarkt für Vorarlberger Unternehmen? T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 195 EP - 205 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Matylitskaya, Volha A1 - Partel, Stefan A1 - Kasemann, Stephan ED - Vajda, Jan ED - Jamnicky, Igor T1 - Study of selective wet etching of titanium towards copper in hydrofluoric free etchant T2 - Proceedings of the 21st International Conference on Applied Physics of Condensed Matter (APCOM 2015) and of the Scientific Conference on Advanced Fast Reactors. June 24 - 26, 2015. Strbske Pleso, Slovak Republic Y1 - 2015 SP - 272 EP - 276 PB - Nakl. STU CY - Bratislava ER - TY - CHAP A1 - Alton-Scheidl, Roland A1 - Radzieowski, Ulrich ED - Jost, Patrick ED - Künz, Andreas T1 - Die Dominanz von Microsoft im Bildungssektor in Österreich und Alternativen T2 - Digitale Medien in Arbeits- und Lernumgebungen. Beiträge zum Usability Day XIII. 12. Juni 2015 Y1 - 2015 SP - 67 EP - 75 PB - Pabst Science Publ. CY - Lengerich ER - TY - JOUR A1 - Fredersdorf, Frederic A1 - Schwarzer, Judith A1 - Engel, Dominik T1 - Die Sicht der Endanwender im Smart Meter Datenschutz JF - Datenschutz und Datensicherheit. DuD. Recht und Sicherheit in Informationsverarbeitung und Kommunikation KW - Coding and Information Theory KW - Computer Science, general KW - Data Encryption KW - Data Structures, Cryptology and Information Theory KW - Legal Aspects of Computing Y1 - 2015 U6 - http://dx.doi.org/10.1007/s11623-015-0498-1 SN - 1614-0702 SN - 1862-2607 VL - 39. Jg. IS - H. 10 SP - 682 EP - 686 ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Roux, Pascale A1 - Rebitzer, Fabian A. ED - Fredersdorf, Frederic T1 - Klienten- und Teamorientierung in der stationären Altenpflege T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 91 EP - 100 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Puhr, Rainer A1 - Fredersdorf, Frederic ED - Fredersdorf, Frederic T1 - Monitoring der Vorarlberger Wirtschaft aus Sicht von Klein- und Mittelunternehmen T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 185 EP - 193 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Roux, Pascale A1 - Moser, Sarah A1 - Fredersdorf, Frederic ED - Tummino, Micol ED - Bollati, Martina ED - Widmann, Martina T1 - Biopsychosocial health of former youth welfare institution residents - self assessment and assessment by others T2 - Linking technology and psychology. Feeding the mind, energy for life. The 14th European Congress of Psychology. Abstract book. Milan, Italy 7-10 July 2015 Y1 - 2015 PB - Innexta CY - Milano ER - TY - CHAP A1 - Roux, Pascale A1 - Fredersdorf, Frederic A1 - Rebitzer, Fabian A. ED - Fredersdorf, Frederic T1 - Die Vorarlberger Ausbildung zum Turnusarzt T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 131 EP - 140 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Fredersdorf, Frederic T1 - Prädiktoren für Bewohnerorientierung in der Altenpflege T2 - Evidenzbasierung in der Gesundheitsförderung. Tagungsband. Frühjahrestagung. Wien, 21. Mai 2015 KW - Altenpflege KW - Bewohnerorientierung KW - Multiple Regression KW - Prädiktoren Y1 - 2015 SP - 31 EP - 33 PB - DeGEval - Arbeitskreis Gesundheit Eigenverl. CY - Wien ER - TY - BOOK ED - Fredersdorf, Frederic T1 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung T3 - Forschung und Entwicklung in der Sozial(arbeits)wissenschaft Y1 - 2015 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Jost, Patrick ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Psychophysiologisch unterstützte Evaluation instruktionsorientierter User-Interfaces T2 - design2product. Beiträge zur empirischen Designforschung. Methoden der Designforschung Y1 - 2015 SP - 182 EP - 204 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Roux, Pascale T1 - Gesundheit aus der Perspektive von ehemals wohnungslosen Personen T2 - Wohnopoly. Wohnen von oben bis unten Y1 - 2015 SP - 47 EP - 63 PB - Eigenverl. CY - Wien ER - TY - CHAP A1 - Mayer, Horst O. A1 - Kneidl, Michael A1 - Gstrein, Carina ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Eindrucksurteile zu statischen vs. dynamischen Piktogrammen T2 - design2product. Beiträge zur empirischen Designforschung. Methoden der Designforschung Y1 - 2015 SP - 107 EP - 129 PB - Bucher CY - Hohenems u.a. ER - TY - RPRT A1 - Wilms, Falko E. P. T1 - Eine kybernetische Analyse des St.Galler Management-Modells der 4. Generation T3 - Arbeitsbericht Department Sozial- und Organisationswissenschaften - 1 Y1 - 2015 PB - Univ. of Applied Sciences CY - Dornbirn ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Führung im St.Galler Management-Modell der 4. Generation JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2015 VL - 14. Jg. IS - H. 2 SP - 113 EP - 122 ER - TY - CHAP A1 - Kriz, Willy Christian ED - Blötz, Ulrich T1 - Trainerkompetenz als Erfolgsfaktor für die Qualität in Planspielen T2 - Planspiele und Serious Games in der beruflichen Bildung. DVD-ROM: Fachbeiträge Y1 - 2015 PB - Bertelsmann CY - Bielefeld ET - 5., überarb. Aufl. ER - TY - CHAP A1 - Mayer, Brigitte T1 - Prozessorientierte Betreuung schriftlicher Abschlussarbeiten in Kleingruppen. [Poster] T2 - Österreichischer Bibliothekartag 2015. Wien 15.-18. September 2015. Y1 - 2015 ER - TY - CHAP A1 - Roux, Pascale ED - Fredersdorf, Frederic T1 - Suchtprävention für Eltern mit türkischem Migrationshintergrund T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 77 EP - 89 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Mayer, Horst O. A1 - Zimmermann, Kevin ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Das semantische Differential am Beispiel einer Untersuchung zu Food Design in der Werbefotografie. T2 - design2product. Beiträge zur empirischen Designforschung. Methoden der Designforschung Y1 - 2015 SP - 86 EP - 106 PB - Bucher CY - Hohenems u.a. ER - TY - JOUR A1 - Rahmatian, Nima A1 - Mei, Renwei A1 - Klausner, James F. A1 - Petrasch, Jörg T1 - A coupled transport model for water splitting within a porous metal oxide thermochemical reactor using the random walk particle tracking method JF - International Journal of Hydrogen Energy Y1 - 2015 U6 - http://dx.doi.org/10.1016/j.ijhydene.2015.02.030 VL - Vol. 40 IS - H. 13 SP - 4451 EP - 4460 ER - TY - CHAP A1 - Rebitzer, Fabian A. A1 - Moser, Sarah ED - Fredersdorf, Frederic T1 - Sozialkapital und Bürgerschaftliches Engagement in Vorarlberg T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 143 EP - 153 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Kriz, Willy Christian ED - Kaneda, Toshiyuki ED - Kanegae, Hidehiko ED - Rizzi, Paola ED - Toyoda, Yusuke T1 - Time capsule of gaming simulation. Back to the future of ISAGA T2 - Hybrid simulation & gaming in the networked society. The 46th ISAGA Annual Conference. The 3rd JASAG World Conference. ISAGA/JASAG 2015. 17th-21st July, 2015. Kyoto, Japan Y1 - 2015 SP - 5/4 EP - 32 PB - ISAGA/JASAG CY - Kyoto ER - TY - CHAP A1 - Hefel, Johanna A1 - Moser, Sarah A1 - Wetzstein, Irmgard ED - Fredersdorf, Frederic T1 - Jugendliche mit Migrationshintergrund auf dem Weg in den Arbeitsmarkt: Evaluierung eines arbeitsmarktpolitischen Modellprojekts T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 103 EP - 129 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Manahl, Werner ED - Kaneda, Toshiyuki ED - Kanegae, Hidehiko ED - Rizzi, Paola ED - Toyoda, Yusuke T1 - Understanding and changing systems through hybrid simulation game design methods in educational contexts T2 - Hybrid simulation & gaming in the networked society. The 46th ISAGA Annual Conference. The 3rd JASAG World Conference. ISAGA/JASAG 2015. 17th-21st July, 2015. Kyoto, Japan Y1 - 2015 SP - 6 EP - 18/121-135 PB - ISAGA/JASAG CY - Kyoto ER - TY - CHAP A1 - Hefel, Johanna ED - Pantucek-Eisenbacher, Peter ED - Vyslouzil, Monika T1 - Mit Vielfalt leben. Dozentin der Sozialen Arbeit T2 - 30 Tage Sozialarbeit. Berichte aus der Praxis Y1 - 2015 SN - 978-3-643-50680-1 SP - 215 EP - 222 PB - Lit CY - Wien ER - TY - CHAP A1 - Roux, Pascale A1 - Feuerstein, Gerhild ED - Fredersdorf, Frederic T1 - Stationäre Jugendhilfe T2 - Anwendungsorientierte Sozial- und Sozialarbeitsforschung in Vorarlberg. Kooperationen mit gesellschaftlicher Wirkung KW - Organizational Studies, Economic Sociology KW - Social Structure, Social Inequality KW - Social Work Y1 - 2015 SN - 978-3-658-11189-2 SN - 978-3-658-11190-8 SP - 27 EP - 39 PB - Springer VS CY - Wiesbaden ER - TY - CHAP A1 - Tipton, Elizabeth A1 - Leigh, Elyssebeth A1 - Kriz, Willy Christian A1 - Crookall, David ED - Kaneda, Toshiyuki ED - Kanegae, Hidehiko ED - Rizzi, Paola ED - Toyoda, Yusuke T1 - Debriefing. The real learning begins when the game stops T2 - Hybrid simulation & gaming in the networked society. The 46th ISAGA Annual Conference. The 3rd JASAG World Conference. ISAGA/JASAG 2015. 17th-21st July, 2015. Kyoto, Japan Y1 - 2015 SP - 5/1 EP - 3 PB - ISAGA/JASAG CY - Kyoto ER - TY - CHAP A1 - Fäßler, Bernhard A1 - Kepplinger, Peter A1 - Kolhe, Mohan Lal A1 - Petrasch, Jörg T1 - Decentralized on-site optimization of a battery storage system using one-way communication T2 - International Conference on Renewable Power Generation (RPG 2015), 17-18 Oct. 2015. Y1 - 2015 U6 - http://dx.doi.org/10.1049/cp.2015.0304 ER - TY - CHAP A1 - Kriz, Willy Christian ED - Blötz, Ulrich T1 - Gaming simulation - 'State of the Art International 2013' T2 - Planspiele und Serious Games in der beruflichen Bildung. Auswahl, Konzepte, Lernarrangements, Erfahrungen - Aktueller Katalog für Planspiele und Serious Games 2015 Y1 - 2015 SP - 263 EP - 272 PB - Bertelsmann CY - Bielefeld ET - 5., überarb. Aufl. ER - TY - CHAP A1 - Baumeister, Alexander A1 - Ilg, Markus A1 - Werkmeister, Clemens T1 - Systeme des Controllings. Modul 21 T2 - Schweitzer, Marcell ; Baumeister, Alexander: Allgemeine Betriebswirtschaftslehre. Theorie und Politik des Wirtschaftens in Unternehmen Y1 - 2015 SP - 981 EP - 1029 PB - Schmidt CY - Berlin ET - 11., völlig neu bearb. Aufl. ER - TY - BOOK ED - Böhler, Ingrid ED - Weber, Wolfgang T1 - Jugendfürsorge und Heimerziehung in Österreich T3 - Zeitgeschichte, 42/3 Y1 - 2015 PB - Studienverl. CY - Innsbruck u.a. ER - TY - BOOK ED - Graf, Maximilian ED - Meisinger, Agnes ED - Weber, Wolfgang T1 - Sport im Kalten Krieg T3 - Zeitgeschichte, 42/4 Y1 - 2015 PB - Studienverl. CY - Innsbruck u.a. ER - TY - BOOK ED - Wilms, Falko E. P. T1 - Lernen in Organisationen T3 - Wandel und Kontinuität in Organisationen, 16 Y1 - 2015 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - BOOK ED - Jost, Patrick ED - Künz, Andreas T1 - Digitale Medien in Arbeits- und Lernumgebungen. Beiträge zum Usability Day XIII. 12. Juni 2015 Y1 - 2015 SN - 978-3-95853-067-6 PB - Pabst Science Publ. CY - Lengerich ER - TY - CHAP A1 - Descher, Marco A1 - Feilhauer, Thomas A1 - Amann, Lucia ED - Kern, Thomas ED - Kastner, Johann ED - Jungwirth, Mario ED - Mayr, Herwig ED - Rau, Christiane T1 - Automated user documentation generation based on the Eclipse application model T2 - 9. Forschungsforum der Österreichischen Fachhochschulen. Wegbereiter - Karrierepfade durch ein Fachhochschulstudium. FH Oberösterreich, Campus Hagenberg. 8. und 9. April 2015. Tagungsband Y1 - 2015 PB - FH OÖ Forschungs & Entwicklungs GmbH CY - Wels ER - TY - JOUR A1 - Szabo, Anna A1 - Ruzsanyi, Veronika A1 - Unterkofler, Karl A1 - Mohacsi, Arpad A1 - Tuboly, Eszter A1 - Boros, Mihaly A1 - Szabo, Gabor A1 - Hinterhuber, Hartmann A1 - Amann, Anton T1 - Exhaled methane concentration profiles during exercise on an ergometer JF - Journal of Breath Research Y1 - 2015 U6 - http://dx.doi.org/10.1088/1752-7155/9/1/016009 SN - 1752-7163 VL - 9. Jg. IS - H. 1 ER - TY - JOUR A1 - Unterkofler, Karl A1 - King, Julian A1 - Mochalski, Pawel A1 - Jandacka, Martin A1 - Koc, Helin A1 - Teschl, Susanne A1 - Anton Amann, A1 - Teschl, Gerald T1 - Modeling-based determination of physiological parameters of systemic VOCs by breath gas analysis: a pilot study JF - Journal of Breath Research Y1 - 2015 U6 - http://dx.doi.org/10.1088/1752-7155/9/3/036002 SN - 1752-7163 VL - 9. Jg. IS - H. 3 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Unterkofler, Karl A1 - Spanel, Patrik A1 - Smith, David A1 - Amann, Anton T1 - Product ion distributions for the reactions of NO+ with some N-containing and O-containing heterocyclic compounds obtained using SRI-TOF-MS JF - International Journal of Mass Spectrometry KW - Fragmentation patterns KW - Heterocyclic compounds KW - NO+ reactions KW - PTR-MS KW - SRI-TOF-MS KW - VOCs Y1 - 2015 U6 - http://dx.doi.org/10.1016/j.ijms.2015.06.003 SN - 1387-3806 VL - o.Jg. IS - Bd. 386 SP - 42 EP - 46 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Unterkofler, Karl A1 - Teschl, Gerald A1 - Amann, Anton T1 - Potential of volatile organic compounds as markers of entrapped humans for use in urban search-and-rescue operations JF - TrAC. Trends in Analytical Chemistry KW - Biomarker KW - Earthquake KW - Entrapment KW - Human scent KW - Human volatilome KW - Search and rescue operation KW - Urban environment KW - VOC KW - Volatile marker KW - Volatile organic compound Y1 - 2015 U6 - http://dx.doi.org/10.1016/j.trac.2015.02.013 SN - 0165-9936 VL - o.Jg. IS - Bd. 68 SP - 88 EP - 106 ER - TY - CHAP A1 - Unterkofler, Karl A1 - Teschl, Susanne ED - Kern, Thomas ED - Kastner, Johann ED - Jungwirth, Mario ED - Mayr, Herwig ED - Rau, Christiane T1 - Modeling the dynamic of breath methane concentration profiles during exercise on an ergometer T2 - 9. Forschungsforum der Österreichischen Fachhochschulen. Wegbereiter - Karrierepfade durch ein Fachhochschulstudium. FH Oberösterreich, Campus Hagenberg. 8. und 9. April 2015. Tagungsband Y1 - 2015 PB - FH OÖ Forschungs & Entwicklungs GmbH CY - Wels ER - TY - JOUR A1 - Breuer, Thomas A1 - Jandacka, Martin A1 - Summer, Martin A1 - Vollbrecht, Hans-Joachim T1 - Endogenous leverage and asset pricing in double auctions JF - Journal of Economic Dynamics and Control KW - Agent based modeling KW - Asset pricing KW - Double auction KW - Leverage KW - Trade on networks Y1 - 2015 U6 - http://dx.doi.org/10.1016/j.jedc.2015.02.004 SN - 0165-1889 VL - o.Jg. IS - Bd. 53 SP - 144 EP - 160 ER - TY - JOUR A1 - Seyringer, Dana T1 - Children's University. Optics and photonics for children JF - Journal of international scientific publications. Educational alternatives Y1 - 2015 UR - https://www.scientific-publications.net/get/1000013/1440675678485024.pdf SN - 1314 7277 VL - 13. Jg. SP - 130 EP - 137 ER - TY - JOUR ED - Böhler, Doris T1 - Czech and Slovak social work BT - ERIS journal - Summer 2015. Connecting theory and practice Y1 - 2015 UR - http://www.socialniprace.cz/soubory/sp_3-2015_web-150831172344.pdf VL - 15. Jg. IS - H. 3 ER - TY - CHAP A1 - Domke, Matthias A1 - Piredda, Giovanni A1 - Stroj, Sandra T1 - Calculating the optimal combination of pulse-to-pulse distance and fluence for scribing and surface ablation with ultrashort pulsed lasers T2 - LiM 2015. Lasers in Manufacturing. Proceedings. Internationales Congress Center München, Germany. June 22-25, 2015 Y1 - 2015 UR - https://www.wlt.de/lim/Proceedings2015/Stick/9.html ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Führung ist Sensemaking. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2015 UR - http://www.trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/24224-problemloesungsprozesse-initiieren-fuehrung-ist-sensemaking VL - o.Jg. IS - Nr. 86 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Beobachten und Bewerten. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2015 UR - http://www.trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/24102-problemloesungsprozesse-initiieren-beobachten-und-bewerten VL - o.Jg. IS - Nr. 85 ER - TY - CHAP A1 - Domke, Matthias A1 - Piredda, Giovanni A1 - Zehetner, Johann A1 - Stroj, Sandra T1 - Minimizing the surface roughness for silicon ablation with ultrashort laser pulses T2 - Proceedings of LAMP2015 - the 7th International Congress on Laser Advanced Materials Processing Y1 - 2015 ER - TY - JOUR A1 - Simma, Armin T1 - Trusting your cloud provider. Protecting private virtual machines JF - Magdeburger Journal zur Sicherheitsforschung Y1 - 2015 UR - http://www.sicherheitsforschung-magdeburg.de/uploads/journal/MJS_036_Simma_TrustingCloud.pdf VL - 5. Jg. IS - H. 9 SP - 530 EP - 539 ER - TY - CHAP A1 - Piredda, Giovanni A1 - Rein, Andreas A1 - Zehetner, Johann A1 - Matylitsky, Victor V. T1 - Mechanical properties of ultrafast-laser cut poly(lactic acid) films T2 - LiM 2015. Lasers in Manufacturing. Proceedings. Internationales Congress Center München, Germany. June 22-25, 2015 Y1 - 2015 UR - https://www.wlt.de/lim/Proceedings2015/Stick/9.html ER - TY - JOUR A1 - Burtscher, Catalina A1 - Lucki, Michal A1 - Seyringer, Dana T1 - Comparison of optical properties of 1x8 splitters based on Y-branch and MMI approaches JF - Romanian Reports in Physics Y1 - 2015 UR - http://www.rrp.infim.ro/2015_67_4.html VL - Bd. 67 IS - H. 4 SP - 1578 EP - 1585 ER - TY - JOUR A1 - Böhler, Doris T1 - Partizipation durch experimentelle Lehr- und Lernformen im Studium Soziale Arbeit. Eine Analyse von Reflexionspapieren im Anschluss an Rollenspiele JF - soziales_kapital KW - Dokumentenanalyse KW - experimentelle Lehr- und Lernformen KW - Reflexionsfähigkeiten KW - Reflexionspapiere KW - Rollenspiele Y1 - 2015 UR - http://soziales-kapital.at/index.php/sozialeskapital/article/view/380 SN - 2070-3481 VL - o.Jg. IS - Nr. 14 SP - 8 EP - 19 ER - TY - JOUR A1 - Horn, Sierk A. T1 - Subsidiary capacity building in emerging markets BT - How Japanese MNEs sequence market entry and development strategies in India JF - Thunderbird International Business Review Y1 - 2015 U6 - http://dx.doi.org/10.1002/tie.21727 VL - 58. Jg. IS - H. 1 SP - 55 EP - 74 ER - TY - JOUR A1 - Horn, Sierk A. T1 - The front end of Interdisciplinarity BT - An acculturation framework for explaining varieties of engagement JF - Issues in Interdisciplinary Studies Y1 - 2015 VL - 33. Jg. SP - 210 EP - 240 ER - TY - CHAP A1 - Jüster, Markus A1 - Lorünser, Daniela A1 - Redzepi, Abdullah A1 - Tarnutzer, Silvan ED - Fredersdorf, Frederic ED - Jüster, Markus ED - Olbert-Bock, Sibylle ED - Otto, Ulrich T1 - Leben und Wirtschaften im Dreiländerraum östlicher Bodensee T2 - Generationenmanagement. Unternehmen durch den demografischen Wandel begleiten Y1 - 2014 SP - 29 EP - 47 PB - Lambertus-Verl. CY - Freiburg im Breisgau ER - TY - BOOK ED - Walter, Wolfgang T1 - Hochschule als imaginierte Institution T3 - Wandel und Kontinuität in Organisationen, 15 Y1 - 2014 SN - 978-3-86573-835-6 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Walter, Wolfgang ED - Walter, Wolfgang T1 - Funktionalisierung der Hochschule T2 - Hochschule als imaginierte Institution Y1 - 2014 SP - 65 EP - 73 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - JOUR A1 - Walter, Wolfgang T1 - Hochschulen als soziale Systeme JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2014 VL - 13. Jg. IS - H. 2 SP - 55 EP - 66 ER - TY - JOUR A1 - Comin, Alberto A1 - Ciesielski, Richard A1 - Piredda, Giovanni A1 - Donkers, Kevin A1 - Hartschuh, Achim T1 - Compression of ultrashort laser pulses via gated multiphoton intrapulse interference phase scans JF - Journal of the Optical Society of America B. Optical physics KW - Physics - Optics Y1 - 2014 VL - 31. Jg. IS - H. 5 SP - 1118 EP - 1125 ER - TY - JOUR A1 - Beyer, Hans-Georg A1 - Melkozerov, Alexander T1 - The dynamics of self-adaptive multi-recombinant evolution strategies on the general ellipsoid model JF - IEEE transactions on evolutionary computation KW - Analytical models KW - Approximation methods KW - ellipsoid model KW - Ellipsoids KW - Evolution strategy KW - linear programming KW - Mathematical model KW - progress rate KW - self-adaptation KW - Standards KW - Vectors Y1 - 2014 U6 - http://dx.doi.org/10.1109/TEVC.2013.2283968 SN - 1089-778X VL - 18. Jg. IS - H. 5 SP - 764 EP - 778 ER - TY - CHAP A1 - Weber, Wolfgang ED - Engelsing, Tobias T1 - Stephanie Hollenstein. Frontsoldatin und Künstlerin T2 - Die Grenze im Krieg. Der Erste Weltkrieg am Bodensee. Sonderausstellung 2014, Rosgartenmuseum Konstanz Y1 - 2014 SP - 128 EP - 129 PB - Rosgartenmuseum CY - Konstanz ER - TY - CHAP A1 - Domke, Matthias A1 - Felsl, Dominik A1 - Rapp, Stephan A1 - Sotrop, Jürgen A1 - Huber, Heinz P. A1 - Schmidt, Michael T1 - The role of shockwaves in confined laser ablation T2 - Proceedings of LPM 2014 - the 15 th International Symposium on Laser Precision Microfabrication Y1 - 2014 PB - Japan Laser Processing Society CY - Ibaraki ER - TY - JOUR A1 - Baumeister, Alexander A1 - Ilg, Markus T1 - Was Flexibilität in Software-Projekten kosten darf JF - Controlling & management review KW - Accounting/Auditing KW - Business/Management Science, general Y1 - 2014 U6 - http://dx.doi.org/10.1365/s12176-014-0899-2 SN - 2195-8262 SN - 2195-8270 VL - 58. Jg. IS - H. 7 SP - 102 EP - 110 ER - TY - RPRT A1 - Ilg, Markus T1 - Crowdfunding - Chancen und Risiken für Unternehmen und Investoren. Modul 3: Crowdfunding & -investing. Crowdfunding als Finanzierungsinstrument für junge Unternehmen in Vorarlberg. Y1 - 2014 ER - TY - RPRT A1 - Ilg, Markus T1 - Crowdfunding - Chancen und Risiken für Unternehmen und Investoren. Modul 4: Empfehlungen zu Crowdfunding und -investing. Y1 - 2014 ER - TY - CHAP A1 - Kotikoski, Tuula-Harriet A1 - Doshi, Natasha ED - Jager, Sake ED - Bradley, Linda ED - Meima, Estelle J. ED - Thouesny, Sylvie T1 - Language learning 2.0 – international collaboration made easy T2 - CALL Design: principles and practice. Proceedings of the 2014 EUROCALL Conference, Groningen, The Netherlands Y1 - 2014 SP - 185 EP - 190 PB - Research-publishing.net CY - Dublin ER - TY - JOUR A1 - Rapp, Stephan A1 - Rosenberger, Janosch A1 - Domke, Matthias A1 - Heise, Gerhard A1 - Huber, Heinz P. A1 - Schmidt, Michael T1 - Ultrafast pump-probe microscopy reveals the mechanism of selective fs laser structuring of transparent thin films for maskless micropatterning JF - Applied Surface Science KW - Laser ablation KW - Pump-probe microscopy KW - thin film KW - Ultra-short pulse laser Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.apsusc.2013.11.086 SN - 0169-4332 VL - o.Jg. IS - Bd. 290 SP - 368 EP - 372 ER - TY - CHAP A1 - Wilms, Falko E. P. T1 - Kommunikation formt Gruppen T2 - Von Böse und Gut. Ein Versuch über Gewalt und Missbrauch. Bubenburg 1950 - 1980 Y1 - 2014 SP - 70 EP - 72 PB - slw Soziale Dienste der Kapuziner CY - Innsbruck ER - TY - RPRT A1 - Ilg, Markus T1 - Crowdfunding - Chancen und Risiken für Unternehmen und Investoren. Modul 1: Betriebswirtschaftliche und rechtliche Grundlagen im Crowdfunding. Y1 - 2014 ER - TY - CHAP A1 - Öttl, Markus A1 - Schmitt, Thomas A1 - Schneider, Reinhard T1 - Implementation of power semiconductor aging behavior in an electric vehicle powertrain model T2 - 2014 15th International Workshop on Research and Education in Mechatronics (REM). 9 - 11 September 2014. El Gouna - Egypt Y1 - 2014 SN - 978-1-4799-3029-6 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Künz, Andreas A1 - Ritter, Walter ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Alternative Interfaces für Museumsexponate T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 145 EP - 159 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Fitz-Rankl, Stefan ED - Holzinger, Helmut ED - Koleznik, Kurt T1 - Fachhochschulen in der Wachstumsfalle? Über Chancen und Risiken der Prolongation eines Erfolgsmodells T2 - 20 Jahre Fachhochschulen in Österreich. Rolle und Wirkung KW - +AWC 620 KW - Fachhochschule : Verwaltung, Organisation Y1 - 2014 SN - 978-3-7089-1201-1 SP - 271 EP - 275 PB - Facultas.WUV CY - Wien ER - TY - CHAP A1 - Lederhaas, Susanna A1 - Weidmann, Karl-Heinz ED - Stephanidis, Constantine T1 - Webster. A new information system for the web T2 - HCI International 2014. Posters’ extended abstracts. International Conference, HCI International 2014. Heraklion, Crete, Greece, June 22-27, 2014 Proceedings, Part I KW - Computer Applications KW - User Interfaces and Human Computer Interaction KW - Information Systems and Communication Service KW - Computer Imaging, Vision, Pattern Recognition and Graphics KW - Computing Milieux KW - information system KW - Media Design KW - search engine KW - semantic technologies KW - tags Y1 - 2014 SN - 978-3-319-07856-4 SN - 978-3-319-07857-1 SP - 180 EP - 185 PB - Springer CY - Cham u.a. ER - TY - CHAP A1 - Mouton, Madeleine A1 - Weidmann, Karl-Heinz ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - How much does packaging influence consumer choices in regards to buying organically? T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 133 EP - 143 PB - Bucher CY - Hohenems u.a. ER - TY - BOOK ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Design2product. Beiträge zur empirischen Designforschung. Die Generation Plus T3 - design2product, 4 KW - +KDC 122 KW - Design : Theorie, Reflexion Y1 - 2014 SN - 978-3-99018-310-6 PB - Bucher CY - Hohenems (u.a.) ER - TY - CHAP A1 - Wechner, Daniel A1 - Weidmann, Karl-Heinz ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Eindruckswirkung von 3D Visualisierungen T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 161 EP - 176 PB - Bucher CY - Hohenems u.a. ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Lernen mit Planspielen. Rollen übernehmen in fehlerfreundlichen Umwelten JF - Wirtschaftspsychologie aktuell. Zeitschrift für Personal und Management Y1 - 2014 VL - 21.Jg. IS - H. 4 SP - 13 EP - 16 ER - TY - RPRT A1 - Ilg, Markus T1 - Crowdfunding - Chancen und Risiken für Unternehmen und Investoren. Modul 2: Vergleich von Crowdfundingplattformen. Y1 - 2014 ER - TY - BOOK A1 - Brettel, Malte A1 - Dittmann, Uwe A1 - Englberger, Hermann A1 - Hirschhausen, Christian von A1 - Leipnitz-Ponto, Yvonne A1 - Olsowski, Gunter A1 - Schätter, Alfred A1 - Schmager, Burkhard A1 - Schuchardt, Christian T1 - Qualifikationsrahmen Wirtschaftsingenieurwesen Y1 - 2014 PB - FFBT Wirtschaftsingenieurwesen CY - Pforzheim ET - 2., überarb. Aufl. ER - TY - CHAP A1 - Weber, Wolfgang ED - Engelsing, Tobias T1 - Das Kronland vor dem Arlberg im Ersten Weltkrieg T2 - Die Grenze im Krieg. Der Erste Weltkrieg am Bodensee. Sonderausstellung 2014, Rosgartenmuseum Konstanz Y1 - 2014 SP - 114 EP - 125 PB - Rosgartenmuseum CY - Konstanz ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Auchter, Eberhard A1 - Wittenzellner, Helmut ED - Kriz, Willy Christian ED - Eiselen, Tanja ED - Manahl, Werner T1 - priME-Cup game-based contests for management, innovation and entrepreneurship T2 - The shift from teaching to learning. Individual, collective and organizational learning through gaming simulation. Proceedings of the 45th Conference of the International Simulation and Gaming Association [CD-ROM] Y1 - 2014 SP - 763 EP - 764 PB - Fachhochschule Vorarlberg CY - Dornbirn ER - TY - CHAP A1 - Auchter, Eberhard A1 - Kriz, Willy Christian ED - Kriz, Willy Christian T1 - The impact of business simulations as a teaching method on entrepreneurial competencies and motivation. A review of 10 years of evaluation research in entrepreneurship education T2 - The shift from teaching to learning. Individual, collective and organizational learning through gaming simulation Y1 - 2014 SP - 187 EP - 197 PB - Bertelsmann CY - Bielefeld ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Teamkommunikation. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2014 VL - o.Jg. IS - Nr. 84 ER - TY - CHAP A1 - Burtscher, Catalina A1 - Seyringer, Dana A1 - Uherek, Frantisek A1 - Chovan, Jozef A1 - Kuzma, Anton ED - Breza, Juraj ED - Donoval, Daniel ED - Varinsky, Erik T1 - Design of low loss 1x64 y-branch splitter having symmetric splitting ratio and small footprint T2 - ASDAM 2014. Conference proceedings. The tenth International Conference on Advanced Semiconductor Devices and Microsystems. Smolenice Castle, Slovakia. 20-22 October 2014 KW - Standards KW - insertion loss KW - integrated optics KW - low loss 1×64 y-branch splitter KW - Optical fibers KW - Optical losses KW - Optical refraction KW - small footprint KW - split power KW - symmetric splitting ratio KW - waveguide structure KW - waveguides KW - Y-branch optical splitter Y1 - 2014 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Glasmacher, Beate ED - Meifert, Matthias T. T1 - Stage 6: Qualification management T2 - Strategic Human Resource development. A journey in eight stages KW - fre Y1 - 2014 SP - 181 EP - 215 PB - Springer CY - Berlin (u.a.) ER - TY - CHAP A1 - Hefel, Johanna ED - Witkin, Stanley L. T1 - Will you be with me to the end? Personal experiences of cancer and death T2 - Narrating social work through autoethnography Y1 - 2014 SN - 978-0-231-15880-0 SN - 0-231-15880-7 SN - 978-0-231-15881-7 SN - 0-231-15881-5 SP - 197 EP - 230 PB - Columbia Univ. Pr. CY - New York, NY (u.a.) ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Walter, Wolfgang T1 - Akademische Lehre mit neuen digitalen Medien T2 - Hochschule als imaginierte Institution Y1 - 2014 SP - 111 EP - 135 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Müller, Oskar ED - Holzinger, Helmut ED - Koleznik, Kurt T1 - Lehre als Kernprozess für die Organisationsentwicklung T2 - 20 Jahre Fachhochschulen in Österreich. Rolle und Wirkung Y1 - 2014 SP - 194 EP - 202 PB - Facultas.WUV CY - Wien ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Planspiele in Unternehmen. Aktuelle Entwicklungen, Einsatzfelder und Trends JF - Personal Manager Y1 - 2014 VL - o.Jg. IS - Nr. 3 SP - 58 EP - 60 ER - TY - CHAP A1 - Zehetner, Johann A1 - Vanko, Gabriel A1 - Choleva, Pavlina A1 - Dzuba, Jaroslav A1 - Ryger, Ivan A1 - Lalinsky, Tibor ED - Breza, Juraj ED - Donoval, Daniel ED - Vavrinsky, Erik T1 - Using of laser ablation technique in the processing technology of GaN/SiC based MEMS for extreme conditions T2 - ASDAM 2014. Conference proceedings. The tenth International Conference on Advanced Semiconductor Devices and Microsystems. Smolenice Castle, Slovakia. 20-22 October 2014 KW - Laser ablation KW - AlGaN-GaN KW - aluminium compounds KW - Aluminum gallium nitride KW - backside damaging KW - epitaxial heterostructures KW - femtosecond laser ablation technique KW - gallium compounds KW - Gallium nitride KW - GaN-SiC KW - HEMT KW - high electron mobility transistors KW - III-V semiconductors KW - MEMS sensors KW - microelectromechanical systems KW - micromechanic structures fabrication KW - Micromechanical devices KW - microsensors KW - Schottky diodes KW - Sensors KW - SiC substrates KW - Silicon carbide KW - silicon compounds KW - Substrates KW - wide band gap semiconductors Y1 - 2014 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Tielebein, Meike T1 - Kollaborative Wissenskonstruktion in der akademischen Lehre T2 - Kybernetik und Wissensgemeinschaft. Vernetztes Denken, geteiltes Wissen - auf dem Weg in die Wissensökonomie. Konferenz für Wirtschafts- und Sozialkybernetik KyWi 2011 vom 7. bis 8. Juli 2011 in Stuttgart Y1 - 2014 SN - 978-3-428-14192-0 SP - 197 EP - 210 PB - Duncker und Humblot CY - Berlin ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Keuper, Frank ED - Arnold, Heinrich T1 - Veränderungen für Dozenten durch Mobile Learning T2 - Campus Transformation. Education, Qualification & Digitalization Y1 - 2014 SN - 978-3-8325-3689-3 SP - 235 EP - 254 PB - Logos Verl. CY - Berlin ER - TY - CHAP A1 - Ritter, Walter A1 - Filkov, Rumen ED - Kempter, Guido ED - Ritter, Walter T1 - Passive infrared motion detector based system to monitor daily structure of people T2 - Assistenztechnik für betreutes Wohnen. Beiträge zum Usability Day XII. 16. Mai 2014 Y1 - 2014 SP - 160 EP - 167 PB - Pabst Science Publ. CY - Lengerich ER - TY - BOOK A1 - Breuer, Thomas T1 - Robustness, validity and significance of the ECB’s asset quality review and stress test exercise. In-depth analysis. Provided at the request of the Economic and Monetary Affairs Commitee Y1 - 2014 SN - 978-92-823-6065-1 PB - Directorate-General for Internal Policies of the Union CY - Brussels ER - TY - JOUR A1 - Beyer, Hans-Georg A1 - Finck, Steffen A1 - Breuer, Thomas T1 - Evolution on trees. On the design of an evolution strategy for scenario-based multi-period portfolio optimization under transaction costs JF - Swarm and evolutionary computation KW - Evolution strategy KW - self-adaptation KW - Covariance matrix adaptation KW - portfolio optimization Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.swevo.2014.03.002 SN - 2210-6502 VL - o.Jg. IS - Bd. 17 SP - 74 EP - 87 ER - TY - BOOK ED - Kriz, Willy Christian ED - Eiselen, Tanja ED - Manahl, Werner T1 - The shift from teaching to learning. Individual, collective and organizational learning through gaming simulation. Proceedings of the 45th Conference of the International Simulation and Gaming Association [CD-ROM] KW - +MAC 340 KW - +MAC 375 KW - Simulation KW - Spieltheorie Y1 - 2014 PB - Fachhochschule Vorarlberg CY - Dornbirn ER - TY - CHAP A1 - Burtscher, Catalina A1 - Seyringer, Dana ED - Vivien, Laurent ED - Honkanen, Seppo ED - Pavesi, Lorenzo ED - Pelli, Stefano T1 - Influence of waveguide structure on Y-branch splitting ratio T2 - Silicon Photonics and Photonic Integrated Circuits IV. 14–17 April 2014. Brussels, Belgium Y1 - 2014 VL - 9133 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Danel, Roman A1 - Repka, Michal A1 - Amann, Robert ED - Ministr, Jan ED - Tvrdikova, Milena T1 - Project EARN as a platform for linking research, innovation, services and education in the field of automation T2 - Proceedings of the 17th international Conference on Information Technology for Practice 2014. October 9-10, 2014, Ostrava, Czech Republic Y1 - 2014 SN - 978-80-248-3555-6 SP - 209 EP - 218 PB - VSB - Technical Univ. of Ostrava CY - Ostrava ER - TY - CHAP A1 - Öttl, Markus A1 - Schmitt, Thomas A1 - Schneider, Reinhard T1 - Lebensdauerabschätzung von Umrichtern in Modellen elektrischer Antriebsstränge T2 - 9. Tag der Mechatronik. 22.09.2014, Dornbirn Y1 - 2014 PB - Fachhochschule Vorarlberg CY - Dornbirn ER - TY - JOUR A1 - Niedermayr, Michael A1 - Lakhmanskiy, Kirill A1 - Kumph, Muir A1 - Partel, Stefan A1 - Edlinger, Johannes A1 - Brownnutt, Michael A1 - Blatt, Rainer T1 - Cryogenic surface ion trap based on intrinsic silicon JF - New Journal of Physics Y1 - 2014 U6 - http://dx.doi.org/10.1088/1367-2630/16/11/113068 SN - 1367-2630 VL - 16. Jg. IS - H. 11 ER - TY - CHAP A1 - Kotikoski, Tuula-Harriet A1 - Doshi, Natasha T1 - Language learning 2.0 - international collaboration made easy T2 - Integrating language, culture and purpose in ESP. Proceedings of the 7th Austrian UAS Language Instructors' Conference 23-24 May 2014 Y1 - 2014 SN - 978-3-200-03564-5 SP - 41 EP - 44 PB - Fachhochschule Technikum Wien CY - Wien ER - TY - CHAP A1 - Böhler, Doris A1 - Fredersdorf, Frederic ED - Hämäläinen, Juha ED - Littlechild, Brian ED - Spilackova, Marie T1 - Social work research at Universities of Applied Sciences in Austria T2 - Social work research across Europe. Methodological positions and research practice. Part II Y1 - 2014 SP - 17 EP - 32 PB - Univ. of Ostrava CY - Ostrava ET - 1. ed. ER - TY - CHAP A1 - Domke, Matthias A1 - Nobile, Luigi A1 - Rapp, Stephan A1 - Eiselen, Sasia A1 - Sotrop, Jürgen A1 - Huber, Heinz P. A1 - Schmidt, Michael ED - Schmidt, Michael ED - Vollertsen, Frank ED - Merklein, Marion T1 - Understanding thin film laser ablation. The role of the effective penetration depth and the film thickness T2 - 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014 KW - Laser ablation KW - thin film KW - confined ablation KW - metal KW - pump-probe Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.phpro.2014.08.012 SP - 1007 EP - 1014 ER - TY - CHAP A1 - Rapp, Stephan A1 - Heinrich, Gerrit A1 - Domke, Matthias A1 - Huber, Heinz P. T1 - The combination of direct and confined laser ablation mechanisms for the selective structuring of thin silicon nitride layers T2 - 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014 KW - Pump-probe microscopy KW - confined laser ablation KW - SiNx thin films Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.phpro.2014.08.011 VL - o.Jg. SP - 998 EP - 1006 ER - TY - JOUR A1 - Beyer, Hans-Georg T1 - Convergence analysis of evolutionary algorithms that are based on the paradigm of information geometry JF - Evolutionary Computation Y1 - 2014 U6 - http://dx.doi.org/10.1162/EVCO_a_00132 SN - 1530-9304 VL - 22. Jg. IS - H. 4 SP - 679 EP - 709 ER - TY - JOUR A1 - Duden, Antje T1 - Successful learning is change JF - International journal of management cases KW - RESEARCH KW - COMMUNICATION KW - CORPORATE culture KW - CORPORATIONS KW - GERMANY KW - LEADERSHIP KW - leadership and management KW - Organization culture KW - ORGANIZATIONAL behavior Y1 - 2014 SN - 17416264 VL - 16. Jg. IS - H. 4 SP - 56 EP - 64 ER - TY - JOUR A1 - Duden, Antje T1 - Nachhaltige Gestaltung von Wertschöpfungsprozessen JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2014 VL - 13. Jg. IS - H. 2 SP - 13 EP - 20 ER - TY - CHAP A1 - Schmidmayr, David A1 - Zehetner, Johann A1 - Amann, Peter ED - Breza, Juraj ED - Donoval, Daniel ED - Vavrinsky, Erik T1 - Investigation of optical stability issues with embedded semiconductor quantum dots used as colour conversion material in LED lighting applications T2 - ASDAM 2014. Conference proceedings. The tenth International Conference on Advanced Semiconductor Devices and Microsystems. Smolenice Castle, Slovakia. 20-22 October 2014 KW - Color KW - Materials KW - Measurement by laser beam KW - Quantum dot lasers KW - Quantum dots KW - Temperature measurement KW - X-rays Y1 - 2014 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Pacher, Tamara A1 - Prinz, Adrian A1 - Stroj, Sandra A1 - Partel, Stefan ED - Klotzbach, Udo ED - Washio, Kunihiko ED - Arnold, Craig B. T1 - Microstructuring of resist double layers by a femtosecond laser ablation and UV lithography hybrid process T2 - Laser-based Micro- and Nanoprocessing VIII. 4-6 February 2014. San Francisco, California, United States Y1 - 2014 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Jüster, Markus A1 - Olbert-Bock, Sibylle A1 - Otto, Ulrich ED - Fredersdorf, Frederic ED - Jüster, Markus ED - Olbert-Bock, Sibylle ED - Otto, Ulrich T1 - Multiperspektivische Studie zum Regionenbezogenen Generationenmanagement im Dreiländerraum östlicher Bodensee T2 - Generationenmanagement. Unternehmen durch den demografischen Wandel begleiten Y1 - 2014 SP - 49 EP - 54 PB - Lambertus-Verl. CY - Freiburg im Breisgau ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Otto, Ulrich A1 - Olbert-Bock, Sibylle ED - Fredersdorf, Frederic ED - Jüster, Markus ED - Olbert-Bock, Sibylle ED - Otto, Ulrich T1 - Regionenbezogenes Generationenmanagement als gesellschaftliche Herausforderung T2 - Generationenmanagement. Unternehmen durch den demografischen Wandel begleiten Y1 - 2014 SP - 13 EP - 27 PB - Lambertus-Verl. CY - Freiburg im Breisgau ER - TY - BOOK ED - Fredersdorf, Frederic ED - Jüster, Markus ED - Olbert-Bock, Sibylle ED - Otto, Ulrich T1 - Generationenmanagement. Unternehmen durch den demografischen Wandel begleiten Y1 - 2014 SN - 978-3-7841-2620-3 PB - Lambertus-Verl. CY - Freiburg im Breisgau ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Jüster, Markus A1 - Lorünser, Daniela A1 - Olbert-Bock, Sibylle A1 - Rebitzer, Fabian A. A1 - Redzepi, Abdullah A1 - Tarnutzer, Silvan ED - Fredersdorf, Frederic ED - Jüster, Markus ED - Olbert-Bock, Sibylle ED - Otto, Ulrich T1 - Regionenbezogenes Generationenmanagement im Dreiländerraum östlicher Bodensee T2 - Generationenmanagement. Unternehmen durch den demografischen Wandel begleiten Y1 - 2014 SP - 55 EP - 123 PB - Lambertus-Verl. CY - Freiburg im Breisgau ER - TY - CHAP A1 - Kepplinger, Peter A1 - Huber, Gerhard A1 - Petrasch, Jörg T1 - Demand side management via autonomous control-optimization and unidirectional communication with application to resistive hot water heaters T2 - Nachhaltige Gebäude. Versorgung - Nutzung - Integration. e-nova. Internationaler Kongress 2014. 13. und 14. November 2014 Y1 - 2014 SP - 79 EP - 86 PB - Leykam CY - Graz ER - TY - JOUR A1 - Partel, Stefan A1 - Kasemann, Stephan A1 - Choleva, Pavlina A1 - Dincer, Can A1 - Kieninger, Jochen A1 - Urban, Gerald A. T1 - Novel fabrication process for sub-micron interdigitated electrode arrays for highly sensitive electrochemical detection JF - Sensors and actuators B: chemical Y1 - 2014 SN - 0925-4005 VL - o.Jg. IS - Bd. 205 SP - 193 EP - 198 ER - TY - JOUR A1 - Eichberger, Jürgen A1 - Rheinberger, Klaus A1 - Summer, Martin T1 - Credit risk in general equilibrium JF - Economic theory KW - Credit risk KW - Bankruptcy KW - D52 KW - D53 KW - Economic Theory KW - Economics general KW - Endogenous risk KW - G01 KW - G33 KW - Game Theory, Economics, Social and Behav. Sciences Y1 - 2014 U6 - http://dx.doi.org/10.1007/s00199-014-0822-2 SN - 0938-2259 SN - 1432-0479 VL - 57. Jg. IS - H. 2 SP - 407 EP - 435 ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Jüster, Markus A1 - Olbert-Bock, Sibylle A1 - Tarnutzer, Silvan ED - Fredersdorf, Frederic ED - Jüster, Markus ED - Olbert-Bock, Sibylle ED - Otto, Ulrich T1 - Zukunft eines Regionenbezogenen Generationenmanagements im Dreiländerraum östlicher Bodensee T2 - Generationenmanagement. Unternehmen durch den demografischen Wandel begleiten Y1 - 2014 SP - 145 EP - 160 PB - Lambertus-Verl. CY - Freiburg im Breisgau ER - TY - CHAP A1 - Simma, Armin A1 - Rusch, Philipp ED - Liaropoulos, Andrew ED - Tsihrintzis, George T1 - Retaining control over private virtual machines hosted by a cloud provider using mandatory access control, trusted boot and attestation T2 - Proceedings of the 13th European Conference on Cyber Warfare and Security. The University of Piraeus Greece. 3-4 July 2014 Y1 - 2014 SP - 172 EP - 180 PB - ACPI CY - Sonning Common ER - TY - CHAP A1 - Olbert-Bock, Sibylle A1 - Rebitzer, Fabian A. A1 - Redzepi, Abdullah ED - Fredersdorf, Frederic ED - Jüster, Markus ED - Olbert-Bock, Sibylle ED - Otto, Ulrich T1 - Generationenmanagement für Klein- und Mittelunternehmen T2 - Generationenmanagement. Unternehmen durch den demografischen Wandel begleiten Y1 - 2014 SP - 125 EP - 144 PB - Lambertus-Verl. CY - Freiburg im Breisgau ER - TY - CHAP A1 - Weber, Wolfgang T1 - Forschungen und Quellen zur Geschichte des Ersten Weltkriegs in Vorarlberg T2 - Papierkrieg. Quellen zur Geschichte des Ersten Weltkrieges in Archiven Österreichs, Deutschlands und Tschechiens Y1 - 2014 SP - 171 EP - 182 PB - Studienverl. CY - Innsbruck ER - TY - CHAP A1 - Mayer, Horst O. A1 - Schwaiger, Lisa Maria ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Eindruckswirkung der Werbeprospekte von Lebensmittelketten in Vorarlberg T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 23 EP - 40 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Mayer, Horst O. A1 - Kneidl, Michael ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Eindruckswirkung unterschiedlicher Schriften bei Kindern und älteren Personen T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 41 EP - 59 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Mayer, Horst O. A1 - Schirmer, Cinja ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Farbwirkung auf die auditive Wahrnehmung T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 83 EP - 100 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Hodzic, Edin A1 - Seyringer, Dana A1 - Uherek, Frantisek A1 - Chovan, Jozef A1 - Kuzma, Anton ED - Breza, Juraj ED - Donoval, Daniel ED - Vavrinsky, Erik T1 - Calculation of accurate channel spacing of an arrayed waveguide grating optical multiplexer/demultiplexer applying position method T2 - ASDAM 2014. Conference proceedings. The tenth International Conference on Advanced Semiconductor Devices and Microsystems. Smolenice Castle, Slovakia. 20-22 October 2014 KW - arrayed waveguide gratings KW - Couplers KW - wavelength division multiplexing KW - Adaptive optics KW - Channel spacing KW - Optical coupling Y1 - 2014 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Seyringer, Dana A1 - Schmid, Patrick A1 - Bielik, Michal A1 - Uherek, Frantisek A1 - Chovan, Jozef A1 - Kuzma, Anton T1 - Design, simulation, evaluation, and technological verification of arrayed waveguide gratings JF - Optical engineering Y1 - 2014 U6 - http://dx.doi.org/10.1117/1.OE.53.7.071803 SN - 0091-3286 VL - 53. Jg. IS - H. 7 ER - TY - CHAP A1 - Hefel, Johanna T1 - Soziale Arbeit in Österreich. Vom Ehrenamt über den Beruf zur Profession T2 - Von Böse und Gut. Ein Versuch über Gewalt und Missbrauch. Bubenburg 1950 - 1980 KW - +SSD 217 KW - Österreich : Sozialarbeit Y1 - 2014 SP - 32 EP - 35 PB - slw Soziale Dienste der Kapuziner CY - Innsbruck ER - TY - JOUR A1 - Jancsary, Peter M. A1 - Wilms, Falko E. P. T1 - Konstruktiv fragen JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2014 VL - 13. Jg. IS - H. 1 SP - 85 EP - 95 ER - TY - CHAP A1 - Fäßler, Bernhard A1 - Zehetner, Johann A1 - Piredda, Giovanni T1 - Systematic study of the roughness of biodegradable polymer surfaces processed by ultrashort laser pulses (M1004) T2 - ICALEO. 33rd International Congress on Applications of Lasers & Electro–Optics. Online Proceedings. October 19th-23rd, 2014. San Diego, CA, USA Y1 - 2014 SP - 188 EP - 196 PB - Laser Institute of America CY - Orlando, Fla ER - TY - CHAP A1 - Rebitzer, Fabian A. ED - Lüthi, Johannes ED - Steinbacher, Hans-Peter T1 - Regionenbezogenes Generationenmanagement für KMU im ländlichen Raum T2 - 8. Forschungsforum der österreichischen Fachhochschulen. Tagungsband. 23. - 24. April 2014, FH Kufstein Tirol. Impulse in Zeiten des Wandels Y1 - 2014 SP - 435 EP - 439 PB - FH Kufstein Tirol CY - Kufstein ER - TY - CHAP A1 - Kempter, Guido A1 - Hofer, Birgit ED - Kempter, Guido ED - Ritter, Walter T1 - Technikbereitschaft und Technikangst T2 - Assistenztechnik für betreutes Wohnen. Beiträge zum Usability Day XII. 16. Mai 2014 Y1 - 2014 SP - 30 EP - 40 PB - Pabst Science Publ. CY - Lengerich ER - TY - CHAP A1 - Kempter, Guido A1 - Ritter, Walter A1 - Künz, Andreas ED - Wichert, Reiner ED - Klausing, Helmut T1 - Guiding light for the mobility support of seniors T2 - Ambient assisted living. 6. AAL-Kongress 2013 Berlin, Germany, January 22-23 , 2013 KW - Aging KW - Biomedical Engineering KW - Geriatrics/Gerontology KW - R & D/Technology Policy Y1 - 2014 SN - 978-3-642-37987-1 SN - 978-3-642-37988-8 SP - 35 EP - 45 PB - Springer CY - Berlin (u.a.) ER - TY - CHAP A1 - Mayer, Horst O. A1 - Wang, Chien-Jen ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Werbesujets für die Generation 60+ T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 9 EP - 22 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Auchter, Eberhard A1 - Wittenzellner, Helmut ED - Davidsson, Per T1 - Long-term effects of the german entrepreneurship education program EXIST-priME-cup T2 - Proceedings of the Australian Centre for Entrepreneurship Research Exchange (ACERE) Conference 2014, Feb 4-7, 2014, University of New South Wales, Sydney, Australia Y1 - 2014 SN - 978-1-921897-96-2 SP - 595 EP - 611 PB - Queensland Univ. of Technology CY - Brisbane ER - TY - CHAP A1 - Weber, Wolfgang ED - Engelsing, Tobias T1 - August Thurnher. Frontsoldat und kommunistischer Funktionär T2 - Die Grenze im Krieg. Der Erste Weltkrieg am Bodensee. Sonderausstellung 2014, Rosgartenmuseum Konstanz Y1 - 2014 SP - 126 EP - 127 PB - Rosgartenmuseum CY - Konstanz ER - TY - CHAP A1 - Matt, Hubert ED - Lund, Cornelia ED - Lund, Holger T1 - Design der Zukunft. Eine Sondierung der Lektüre Latours T2 - Design der Zukunft Y1 - 2014 SP - 35 EP - 61 PB - av-Ed CY - Stuttgart ER - TY - JOUR A1 - Jancsary, Peter M. T1 - Symposium als Raum der Begegnung JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2014 VL - 13. Jg. IS - H. 2 SP - 3 EP - 12 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Akademische Lehre 2.0 JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2014 VL - 13. Jg. IS - H. 2 SP - 67 EP - 88 ER - TY - CHAP A1 - Weber, Wolfgang ED - Kuprian, Hermann J. W. ED - Überegger, Oswald T1 - Vorarlberg T2 - Katastrophenjahre. Der Erste Weltkrieg und Tirol Y1 - 2014 SP - 509 EP - 527 PB - Univ.-Verl. Wagner CY - Innsbruck ER - TY - CHAP A1 - Jost, Patrick A1 - Nousiainen, Johannes Tapio ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Residential design. Investigating the influence of inaudible sounds T2 - design2product. Beiträge zur empirischen Designforschung. Die Generation Plus Y1 - 2014 SP - 121 EP - 131 PB - Bucher CY - Hohenems u.a. ER - TY - THES A1 - Grabher, Dietmar T1 - Governance von webbasierten Business-Plattformen aus Sicht von Lehre und Praxis am Beispiel von Microsoft SharePoint. Ansatzpunkte für die weitere Annäherung von Theorie und Praxis und Anwendungsmöglichkeiten von Microsoft SharePoint als Demonstrationsobjekt in der Wirtschaftsinformatik-Lehre Y1 - 2014 PB - Fachhochschule Vorarlberg CY - Dornbirn ER - TY - CHAP A1 - Weber, Wolfgang T1 - P. Magnus Kerner OFMCap. 1915-1990 T2 - Von Böse und Gut. Ein Versuch über Gewalt und Missbrauch. Bubenburg 1950 - 1980 KW - +SSD 217 KW - Österreich : Sozialarbeit Y1 - 2014 SP - 24 EP - 26 PB - slw Soziale Dienste der Kapuziner CY - Innsbruck ER - TY - CHAP A1 - Fredersdorf, Frederic ED - Lüthi, Johannes ED - Steinbacher, Hans-Peter T1 - Evidenzbasierte ambulante Kinder- und Jugendhilfe T2 - 8. Forschungsforum der österreichischen Fachhochschulen. Tagungsband. 23. - 24. April 2014, FH Kufstein Tirol. Impulse in Zeiten des Wandels Y1 - 2014 SP - 312 EP - 316 PB - FH Kufstein Tirol CY - Kufstein ER - TY - CHAP A1 - Weber, Wolfgang ED - Engelsing, Tobias T1 - August Plankensteiner. Frontoffizier und NS-Funktionär T2 - Die Grenze im Krieg. Der Erste Weltkrieg am Bodensee. Sonderausstellung 2014, Rosgartenmuseum Konstanz Y1 - 2014 SP - 130 EP - 131 PB - Rosgartenmuseum CY - Konstanz ER - TY - JOUR A1 - Rebitzer, Fabian A. A1 - Tarnutzer, Silvan A1 - Otto, Ulrich T1 - Dreiländer-F+E-Projekt Regionenbezogenes Generationenmanagement (RegGen) – Bewältigung des demografischen Wandels in ländlichen KMU JF - Zeitschrift für Gerontologie und Geriatrie. Mit European journal of geriatrics. Abstracts. Stress und Altern - Chancen und Risiken. 24.-27. September 2014 Halle (Saale) Y1 - 2014 VL - 47. Jg. IS - Suppl. 1 ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Grösser, Stefan N. ED - Schwaninger, Markus ED - Tilebein, Meike ED - Fischer, Thomas ED - Jeschke, Sabina T1 - Unterscheidung als Grundoperation in sozialen Systemen. Eine sozialkyberne­tische Betrachtung T2 - Modellbasiertes Management. Konferenz für Wirtschafts- und Sozialkybernetik KyWi 2013 vom 4. bis 5. Juli 2013 in Bern. Y1 - 2014 SN - 978-3-428-14267-5 SP - 35 EP - 49 PB - Duncker und Humblot CY - Berlin ER - TY - BOOK ED - Weber, Wolfgang T1 - Studien zur Mitte des Jahrhunderts - Mid Century Studies. Zeitgeschichte T3 - Zeitgeschichte, 2014/1 Y1 - 2014 PB - Verein für wissenschaftliche Aufarbeitung der Zeitgeschichte CY - Innsbruck ER - TY - BOOK ED - Kriz, Willy Christian T1 - The shift from teaching to learning. Individual, collective and organizational learning through gaming simulation KW - +MAC 340 KW - +MAC 375 KW - Simulation KW - Spieltheorie Y1 - 2014 SN - 978-3-7639-5420-9 PB - Bertelsmann CY - Bielefeld ER - TY - BOOK ED - Duke, Richard D. ED - Kriz, Willy Christian T1 - Back to the future of gaming KW - +MAC 340 KW - +MAC 375 KW - Simulation KW - Spieltheorie Y1 - 2014 SN - 978-3-7639-5425-4 PB - Bertelsmann CY - Bielefeld ER - TY - BOOK ED - Zeller, Ursula ED - Moll, Frank-Thorsten ED - Zeppelin Museum Friedrichshafen, ED - Hils, Claudio T1 - Greser & Lenz. Das ist ja wohl ein Witz! KW - +KAB 190 KW - +KAC 505 KW - Karikatur KW - Kunst (1945- ) : Ausstellungskatalog Y1 - 2014 SN - 978-3-88423-468-6 PB - Verl. Das Wunderhorn CY - Heidelberg ER - TY - CHAP A1 - Geser-Engleitner, Erika ED - Kempter, Guido ED - Ritter, Walter T1 - Kritische Reflexionen über technologieunterstützte Angebote für Betreutes Wohnen im Alter T2 - Assistenztechnik für betreutes Wohnen. Beiträge zum Usability Day XII. 16. Mai 2014 Y1 - 2014 SP - 59 EP - 67 PB - Pabst Science Publ. CY - Lengerich ER - TY - BOOK ED - Kempter, Guido ED - Ritter, Walter T1 - Assistenztechnik für betreutes Wohnen. Beiträge zum Usability Day XII. 16. Mai 2014 Y1 - 2014 SN - 978-3-89967-943-4 PB - Pabst Science Publ. CY - Lengerich ER - TY - THES A1 - Seyringer, Dana T1 - Arrayed waveguide gratings. Design, simulation and technological verification Y1 - 2014 N1 - Jahr der Abschlussprüfung: 2015 CY - Bratislava ER - TY - JOUR A1 - Eiselen, Tanja A1 - Manahl, Werner A1 - Kriz, Willy Christian T1 - Umgang mit Komplexität spielerisch lernen JF - Wirtschaft + Weiterbildung Y1 - 2014 VL - 26. Jg. IS - H. 5 SP - 38 EP - 43 ER - TY - CHAP A1 - Dobler, Martin A1 - Schumacher, Jens T1 - A pan-European ecosystem for intelligent cargo and its impact on emission reduction T2 - TRA. Transport Research Arena. Book of abstracts. 5th conference. Transport solution: from research to deployment. Innovate mobility, mobilise innovation. Paris - La Defense CNIT, 14- 17 April 2014 Y1 - 2014 PB - IFSTTAR CY - Nantes ER - TY - JOUR A1 - Mochalski, Pawel A1 - Al-Zoairy, Ramona A1 - Niederwanger, Andreas A1 - Unterkofler, Karl A1 - Amann, Anton T1 - Quantitative analysis of volatile organic compounds released and consumed by rat L6 skeletal muscle cells in vitro JF - Journal of Breath Research KW - Volatile organic compounds KW - Humans KW - Gas Chromatography-Mass Spectrometry KW - Male KW - Animals KW - Cell Line KW - Exhalation KW - Limit of Detection KW - Muscle Cells KW - Muscle, Skeletal KW - Rats KW - Reproducibility of Results KW - Time Factors Y1 - 2014 U6 - http://dx.doi.org/10.1088/1752-7155/8/4/046003 SN - 1752-7163 VL - 8. Jg. IS - H. 4 ER - TY - JOUR A1 - Mochalski, Pawel A1 - King, Julian A1 - Haas, Matthias A1 - Unterkofler, Karl A1 - Amann, Anton A1 - Mayer, Gert T1 - Blood and breath profiles of volatile organic compounds in patients with end-stage renal disease JF - BMC nephrology KW - Volatile organic compounds KW - Blood analysis KW - Breath analysis KW - End-stage renal disease KW - Hemodialysis KW - Uremic syndrome Y1 - 2014 U6 - http://dx.doi.org/10.1186/1471-2369-15-43 SN - 1471-2369 VL - 15. Jg. IS - H. 3 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Theurl, Markus A1 - Sponring, Andreas A1 - Unterkofler, Karl A1 - Kirchmair, Rudolf A1 - Amann, Anton T1 - Analysis of volatile organic compounds liberated and metabolised by human umbilical vein endothelial cells (HUVEC) in vitro JF - Cell Biochemistry and Biophysics KW - Aldehydes KW - Biochemistry, general KW - Biophysics and Biological Physics KW - Biotechnology KW - Cell Biology KW - GC–MS KW - HUVEC KW - Needle trap KW - Pharmacology/Toxicology KW - Release KW - Uptake KW - Volatile organic compounds Y1 - 2014 U6 - http://dx.doi.org/10.1007/s12013-014-0201-4 SN - 1085-9195 SN - 1559-0283 VL - o.Jg. IS - Bd. 71 SP - 323 EP - 329 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Unterkofler, Karl A1 - Spanel, Patrik A1 - Smith, David A1 - Amann, Anton T1 - Product ion distributions for the reactions of NO+ with some physiologically significant aldehydes obtained using a SRI-TOF-MS instrument JF - International journal of mass spectrometry KW - Aldehydes KW - Fragmentation patterns KW - NO+ reactions KW - PTR-MS KW - SRI-TOF-MS KW - VOCs Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.ijms.2014.02.016 SN - 1387-3806 VL - o.Jg. IS - Bd. 363 SP - 23 EP - 31 ER - TY - CHAP A1 - Descher, Marco A1 - Feilhauer, Thomas ED - Hamza, Mohamed H. T1 - Towards automated application software documentation generation based on the eclipse application model T2 - Proceedings of the IASTED International Conference on Software Engineering (SE 2014). February 17 - 19, 2014 Innsbruck, Austria Y1 - 2014 SP - 39 EP - 45 PB - Acta Pr. CY - Calgary ER - TY - JOUR A1 - Rieder, Florian T1 - Alles Bleibt Anders! Operative und strategische Perspektiven interkultureller Sozialer Arbeit im Zeitalter der Globalisierung JF - soziales_kapital. Wissenschaftliches Journal österreichischer Fachhochschul-Studiengänge Soziale Arbeit Y1 - 2014 UR - http://www.soziales-kapital.at/index.php/sozialeskapital/article/view/314 SN - 2070-3481 VL - o.Jg. IS - Nr. 11 ER - TY - CHAP A1 - Maurer, Florian A1 - Lechner, Ulrike T1 - From disaster response planning to e-Resilience. A literature review T2 - Conference proceedings. 27th Bled eConference. eEcosystems. June 1-5 2014. Bled, Slovenia Y1 - 2014 UR - https://domino.fov.uni-mb.si/proceedings SP - 41 EP - 58 PB - Bled eConference CY - Bled ER - TY - CHAP A1 - Dobler, Martin A1 - Schumacher, Jens T1 - Intelligent cargo ecosystem - impact on resilient supply chains and emissions T2 - 10th ITS European Congress. Helsinki, Finland. 16-19 June 2014. Online conference proceedings Y1 - 2014 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Unterkofler, Karl A1 - Spanel, Patrik A1 - Smith, David A1 - Amann, Anton T1 - Product ion distributions for the reactions of NO+ with some physiologically significant volatile organosulfur and organoselenium compounds obtained using a selective reagent ionization time-of-flight mass spectrometer JF - Rapid communications in mass spectrometry. RCM Y1 - 2014 U6 - http://dx.doi.org/10.1002/rcm.6947 SN - 1097-0231 VL - 28. Jg. IS - H. 15 SP - 1683 EP - 1690 ER - TY - JOUR A1 - Mochalski, Pawel A1 - King, Julian A1 - Unterkofler, Karl A1 - Hinterhuber, Hartmann A1 - Amann, Anton T1 - Emission rates of selected volatile organic compounds from skin of healthy volunteers JF - Journal of chromatography B KW - Volatile organic compounds KW - Emission rate KW - Entrapped victims KW - Human odor KW - Human skin emanation KW - SPME-GCMS Y1 - 2014 U6 - http://dx.doi.org/10.1016/j.jchromb.2014.04.006 SN - 1570-0232 VL - o.Jg. IS - Bd. 959 SP - 62 EP - 70 ER - TY - JOUR A1 - Mochalski, Pawel A1 - Unterkofler, Karl A1 - Hinterhuber, Hartmann A1 - Amann, Anton T1 - Monitoring of selected skin-borne volatile markers of entrapped humans by selective reagent ionization time of flight mass spectrometry in NO+ mode JF - Analytical chemistry Y1 - 2014 U6 - http://dx.doi.org/10.1021/ac404242q SN - 0003-2700 VL - 86. Jg. IS - H. 8 SP - 3915 EP - 3923 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Keine WARUM-Fragen bitte! Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2014 UR - http://www.trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/23749-problemloesungsprozesse-initiieren-keine-warum-fragen-bitte VL - o.Jg. IS - Nr. 83 ER - TY - CHAP A1 - Schmidmayr, David A1 - Zehetner, Johann ED - Vajda, Jan ED - Jamnicky, Igor T1 - Quantum dots, advantages and drawbacks for lighting applications T2 - Proceedings of the 20th International Conference on Applied Physics of Condensed Matter (APCOM 2014). June 25 - 27, 2014. Strbske Pleso, Slovak Republic Y1 - 2014 SP - 30 EP - 34 PB - Nakl. STU CY - Bratislava ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Der Tod wirkt auf das (Er)Leben. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2014 UR - http://www.trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/23476-problemloesungsprozesse-initiieren-der-tod-wirkt-auf-das-er-leben VL - o.Jg. IS - Nr. 82 ER - TY - JOUR A1 - Fredersdorf, Frederic A1 - Posch, Klaus T1 - Vom Nutzen der Sozialarbeitsforschung JF - soziales_kapital. Wissenschaftliches Journal österreichischer Fachhochschul-Studiengänge Soziale Arbeit Y1 - 2014 UR - http://www.soziales-kapital.at/index.php/sozialeskapital/article/view/316/555 VL - o.Jg. IS - Nr. 11 ER - TY - CHAP A1 - Maurer, Florian A1 - Lechner, Ulrike ED - Kundisch, Dennis ED - Suhl, Leena ED - Beckmann, Lars T1 - Resilience in transport logistics T2 - Tagungsband Multikonferenz Wirtschaftsinformatik 2014 (MKWI 2014) Y1 - 2014 UR - http://nbn-resolving.de/urn:nbn:de:hbz:466:2-12778 SN - 978-3-00-045311-3 SP - 294 EP - 306 PB - Univ. Paderborn CY - Paderborn ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Live: Der Kongress entwickelt ein Planspiel! JF - Wirtschaft + Weiterbildung Y1 - 2014 VL - 26. Jg. IS - H. 5 SP - 48 EP - 49 ER - TY - JOUR A1 - Kriz, Willy Christian T1 - 250 Jahre Planspiel. Wie alles begann JF - Wirtschaft + Weiterbildung Y1 - 2014 VL - 26. Jg. IS - H. 5 SP - 50 EP - 52 ER - TY - CHAP A1 - Drzik, Milan A1 - Dzuba, Jaroslav A1 - Vanko, Gabriel A1 - Hudek, Peter A1 - Choleva, Pavlina A1 - Ryger, Ivan A1 - Lalinsky, Tibor T1 - Measurement of the AlGaN/GaN membrane piezoelectric response by pressure loading T2 - 39th International Conference on MNE, 16 to 19 September 2013, London Y1 - 2013 ER - TY - CHAP A1 - Öttl, Markus ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Development of a hybrid control unit in Dymola T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 373 EP - 378 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Ilg, Markus A1 - Baumeister, Alexander ED - Wang, John T1 - Performance management in software engineering T2 - Perspectives and techniques for improving information technology project management Y1 - 2013 SN - 978-1-4666-2800-7 SN - 978-1-4666-2801-4 SP - 51 EP - 68 PB - Information Science Reference CY - Hershey, PA ER - TY - CHAP A1 - Seyringer, Dana ED - Vajda, Jan ED - Jamnicky, Igor T1 - AWG optical demultiplexers. From design to chip T2 - Proceedings of the 19th International Conference on Applied Physics of Condensed Matter (APCOM 2013). June 19 - 21, 2013. Strbske Pleso, Slovak Republic Y1 - 2013 SP - 15 EP - 19 PB - Nakl. STU CY - Bratislava ER - TY - CHAP A1 - Rebitzer, Fabian A. ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Zur Bindung zugewanderter akademischer technischer Fachkräfte an Unternehmen und Region T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 663 EP - 664 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Röhrl, Patrick A1 - Amann, Robert A1 - Ritschel, Patrick ED - Malisa, Viktorio ED - Komenda, Titanilla T1 - Control of an autonomous tennis ball collector T2 - REM 2013 proceedings. 14th International Workshop on Research and Education in Mechatronics. June 6th-7th 2013, Vienna, Austria Y1 - 2013 SP - 155 EP - 160 PB - Verein zur Förderung der Automation und Robotik (F-AR) CY - Wien ER - TY - CHAP A1 - Schmid, Patrick A1 - Schneider, Reinhard ED - Malisa, Viktorio ED - Komenda, Titanilla T1 - Designing FPGA systems with Simulink. Simulink model-based design, verification and test for FPGA hardware T2 - REM 2013 proceedings. 14th International Workshop on Research and Education in Mechatronics. June 6th-7th 2013, Vienna, Austria Y1 - 2013 SN - 978-3-902759-07-8 SP - 112 EP - 117 PB - Verein zur Förderung der Automation und Robotik (F-AR) CY - Wien ER - TY - CHAP A1 - Mayer, Horst O. A1 - Ammann, Agnes ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Eindruckswirkung von Veränderungen bei dynamischen Logos T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 546 EP - 551 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Roux, Pascale A1 - Fredersdorf, Frederic ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Perspektive von GemeindevertreterInnen in der Alkoholprävention bei Jugendlichen T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 80 EP - 87 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Vanko, Gabriel A1 - Hudek, Peter A1 - Zehetner, Johann A1 - Dzuba, Jaroslav A1 - Choleva, Pavlina A1 - Vallo, Martin A1 - Ryger, Ivan A1 - Lalinsky, Tibor ED - Schmid, Ulrich ED - Sanchez de Rojas Aldavero, Jose Luis ED - Leester-Schaedel, Monika T1 - MEMS pressure sensor fabricated by advanced bulk micromachining techniques T2 - Smart sensors, actuators, and MEMS VI. 24-26 April 2013. Grenoble, France Y1 - 2013 PB - SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Mayer, Horst O. A1 - Bauer, Manuel Felix ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Wechselwirkung von Protagonisten und Objekten in der Eindrucksbildung T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2013 SN - 978-3-99018-253-6 SP - 49 EP - 74 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Kriz, Willy Christian T1 - SysTeamsGames. Three games for business management simulation T2 - Proceedings of JASAG 2013 Conference. Linking a bridge between analog and digital games. 2013 Autumn National Conference. December 7-8, 2013 Y1 - 2013 SP - 126 EP - 131 PB - Tohoku Univ. CY - Senday ER - TY - CHAP A1 - Lederhaas, Susanna A1 - Weidmann, Karl-Heinz ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Bruch der Seitenmetapher. Eine Alternative zum derzeitigen Informationssystem des Web T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2013 SN - 978-3-99018-253-6 SP - 11 EP - 30 PB - Bucher CY - Hohenems u.a. ER - TY - BOOK ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - design2product. Beiträge zur empirischen Designforschung T3 - design2product, 3 KW - +KDC 122 KW - Design : Theorie, Reflexion Y1 - 2013 SN - 978-3-99018-253-6 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Mayer, Horst O. A1 - Bentele, Christina ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Eindruckswirkung stereoskopischer Filme T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2013 SN - 978-3-99018-253-6 SP - 31 EP - 47 PB - Bucher CY - Hohenems u.a. ER - TY - JOUR A1 - Lipinski, Wojciech A1 - Davidson, Jane H. A1 - Haussener, Sophia A1 - Klausner, James F. A1 - Mehdizadeh, Ayyoub M. A1 - Petrasch, Jörg A1 - Steinfeld, Aldo A1 - Venstrom, Luke T1 - Review of heat transfer research for solar thermochemical applications JF - Journal of Thermal Science and Engineering Applications Y1 - 2013 U6 - http://dx.doi.org/10.1115/1.4024088 SN - 1948-5085 VL - 5. Jg. IS - H. 2 ER - TY - CHAP A1 - Fredersdorf, Frederic ED - Pflegerl, Johannes ED - Vyslouzil, Monika ED - Pantucek, Gertraud T1 - Organisationales Screening als Baustein sozialer Diagnostik für die stationäre Altenpflege T2 - Passgenau helfen. Soziale Arbeit als Mitgestalterin gesellschaftlicher und sozialer Prozesse. Festschrift für Peter Pantucek Y1 - 2013 SP - 257 EP - 263 PB - Lit CY - Wien u.a. ER - TY - CHAP A1 - Mayer, Horst O. A1 - Brachart, Cathrin ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Eindruckswirkung von BDSM-Motiven in der Werbung T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 568 EP - 570 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Kempter, Guido A1 - Ritter, Walter A1 - Herburger, Martin A1 - Ulmer, Tom ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Ambient unterstützte Gesundheitsdiagnose T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 518 EP - 524 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Schneider, Sharon ED - Koegeler-Abdi, Martina ED - Parncutt, Richard T1 - Transcultural school social work. A case study of children's rights in practice T2 - Interculturality. Practice meets research Y1 - 2013 SN - 978-1-4438-4523-6 SP - 51 EP - 70 PB - Cambridge Scholars Publ. CY - Newcastle upon Tyne ER - TY - JOUR A1 - Tisserant, Jean-Nicolas A1 - Wicht, Gaëtan A1 - Göbel, Ole F. A1 - Bocek, Eva A1 - Bona, Gian-Luca A1 - Geiger, Thomas A1 - Hany, Roland A1 - Mezzenga, Raffaele A1 - Partel, Stefan A1 - Schmid, Peter A1 - Schweizer, Wolfhard Bernd A1 - Heier, Jakob T1 - Growth and alignment of thin film organic single crystals from dewetting patterns JF - ACS Nano Y1 - 2013 U6 - http://dx.doi.org/10.1021/nn401679s SN - 1936-0851 VL - 7. Jg. IS - H. 6 SP - 5506 EP - 5513 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Wertschöpfung und Vertrauen gehören zusammen. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2013 VL - o.Jg. IS - Nr. 81 ER - TY - CHAP A1 - Kriz, Willy Christian ED - Bachmann, Heinz T1 - Erwerb von Systemkompetenz mit Planspielmethoden T2 - Hochschullehre variantenreich gestalten. Kompetenzorientierte Hochschullehre - Ansätze, Methoden und Beispiele Y1 - 2013 SP - 108 EP - 138 PB - Hep, der Bildungsverl. CY - Bern ER - TY - CHAP A1 - Breuer, Thomas A1 - Csiszar, Imre T1 - Information geometry in mathematical finance. Model risk, worst and almost worst scenarios T2 - 2013 IEEE International Symposium on Information Theory Proceedings (ISIT 2013). Istanbul, Turkey, 7 - 12 July 2013 KW - Mathematical model KW - almost worst scenarios KW - Bregman ball KW - Convex functions KW - convex integral functional KW - convex integral functionals KW - Educational institutions KW - f-divergence ball KW - finance KW - geometric intuition KW - geometry KW - I-divergence KW - information geometry KW - Information theory KW - mathematical finance KW - Model risk KW - moment constraints KW - risk analysis KW - Uncertainty Y1 - 2013 SN - 978-1-4799-0446-4 SP - 404 EP - 408 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Schmid, Patrick A1 - Schneider, Reinhard T1 - Implementation issues designing a multilevel converter control for FPGA-based hardware in Simulink T2 - Proceedings. PCIM Europe. International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management. Nuremberg, 14 - 16 May 2013 Y1 - 2013 SN - 978-3-8007-3505-1 SN - 3-8007-3505-9 SP - 1110 EP - 1116 PB - VDE-Verl. CY - Berlin u.a. ER - TY - CHAP A1 - Anker, Martin A1 - Schneider, Reinhard ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Condition Monitoring von Windenergieanlagen mittels Kontinuierlicher Wavelet-Transformation T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 455 EP - 461 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Edlinger, Johannes A1 - Schmidmayr, David A1 - Zehetner, Johann T1 - New developments in quantum dots T2 - LED lighting technologies - winning approaches. LED Professional Symposium +Expo 2013. LpS 2013, Bregenz, 24 - 26 Sept. 2013 Y1 - 2013 SN - 978-3-9503209-2-3 SP - 26 EP - 33 PB - Luger Research CY - Dornbirn ER - TY - RPRT A1 - Finck, Steffen T1 - Analysis of simple pattern search on the noisy sphere model. Arbeitsbericht Prozess- und Produktengineering. Methoden T3 - Arbeitsbericht Prozess- und Produktengineering - 2013 Y1 - 2013 ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Lorünser, Daniela ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Kulturvermittlung. Eine Studie zur Bedeutung und zum Umfang kulturvermittelnder Initiativen in Vorarlberg T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 616 EP - 617 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Roux, Pascale ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Nutzwert von Peer-Education in der Alkoholprävention T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 574 EP - 581 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Seyringer, Dana ED - Jaworski, Marek ED - Marciniak, Marian T1 - Application of AWG-parameters tool in design of colourless 8-channel, 100 GHz AWG T2 - ICTON 2013. 15th International Conference on Transparent Optical Networks. Cartagena, Spain. June 23-27, 2013 KW - arrayed waveguide gratings KW - Crosstalk KW - insertion loss KW - integrated optics KW - Optical device fabrication KW - AWG design KW - AWG design tool KW - AWG transmission parameters KW - AWG-parameters tool KW - colourless 8-channel AWG KW - colourless AWG KW - commercial photonics software tool KW - cyclic AWG KW - demultiplexing equipment KW - frequency 100 GHz KW - Layout KW - multiplexing equipment KW - optical communication equipment KW - optical multiplexers//demultiplexers KW - tool design KW - transmission characteristics Y1 - 2013 SN - 978-1-4799-0682-6 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kempter, Guido A1 - Ritter, Walter A1 - Canazei, Markus ED - Harris, Don T1 - Using light guiding to structure everyday life T2 - Engineering psychology and cognitive ergonomics. Applications and services. 10th International Conference, EPCE 2013. Held as part of HCI international 2013. Las Vegas, NV, USA, July 21-26, 2013. Proceedings, part II KW - Ambient Assisted Living KW - Computer Applications KW - Computers and Society KW - Information Systems Applications (incl. Internet) KW - Lighting KW - Mobility KW - Models and Principles KW - Motion Detection KW - User Interfaces and Human Computer Interaction Y1 - 2013 SN - 978-3-642-39353-2 SN - 978-3-642-39354-9 SP - 351 EP - 357 PB - Springer CY - Berlin (u.a.) ER - TY - JOUR A1 - Vanko, Gabriel A1 - Hudek, Peter A1 - Zehetner, Johann A1 - Dzuba, Jaroslav A1 - Choleva, Pavlina A1 - Kutis, Vladimir A1 - Vallo, Martin A1 - Ryger, Ivan A1 - Lalinsky, Tibor T1 - Bulk micromachining of SiC substrate for MEMS sensor applications JF - Microelectronic Engineering KW - Laser ablation KW - AlGaN/GaN HEMT KW - Bulk micromachining KW - SiC MEMS Y1 - 2013 U6 - http://dx.doi.org/10.1016/j.mee.2013.01.046 SN - 0167-9317 VL - o. Jg. IS - Bd. 110 SP - 260 EP - 264 ER - TY - CHAP A1 - Seyringer, Dana A1 - Bielik, Michal ED - Broquin, Jean Emmanuel ED - Conti, Gualtiero Nunzi T1 - AWG-parameters. New software tool to design arrayed waveguide gratings T2 - Integrated optics. Devices, materials, and technologies XVII. 5-7 February 2013. San Francisco, California, United States Y1 - 2013 PB - SPIE CY - San Francisco, Cal. ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Dialog als Weg des gemeinsamen Denkens JF - Business+Innovation Y1 - 2013 VL - o.Jg. IS - Nr. 3 SP - 52 EP - 59 ER - TY - JOUR A1 - Partel, Stefan A1 - Urban, Gerald A. A1 - Motzek, Kristian T1 - Simulation model validation of two common i-line photoresists JF - Microelectronic Engineering KW - AZ MiR 701 KW - Dissolution rate monitor KW - DRM KW - Lithography simulation KW - Mask-Aligner KW - Mask-Aligner lithography simulation KW - Photoresist calibration KW - SPR 955-CM Y1 - 2013 U6 - http://dx.doi.org/10.1016/j.mee.2013.01.054 SN - 0167-9317 VL - o.Jg. IS - Bd. 110 SP - 75 EP - 79 ER - TY - JOUR A1 - Chovan, Jozef A1 - Kuzma, Anton A1 - Uherek, Frantisek A1 - Seyringer, Dana A1 - Patassy, Gabor T1 - Fotonicke sensory pre zivotne prostredie – monitorovanie kvality pitnej vody JF - Casopis EE Y1 - 2013 VL - 19. Jg. IS - H. 5 SP - 40 EP - 43 ER - TY - CHAP A1 - Seyringer, Dana A1 - Kohler, Linda A1 - Uherek, Frantisek A1 - Chovan, Jozef A1 - Kuzma, Anton ED - Pudis, Dusan ED - Lettrichova, Ivana ED - Suslik, Lubos ED - Kovac, Jaroslav ED - Vincze, Andrej T1 - Influence of waveguide structure on Y-branch splitting T2 - Proceedings of ADEPT 2013. 1st International Conference on Advances in Electronic and Photonic Technologies. Spa Novy Smokovec, High Tatras, Slovakia, June 2-5, 2013 Y1 - 2013 SN - 978-80-554-0689-3 SP - 266 EP - 269 PB - Univ. of Zilina CY - Zilina ER - TY - CHAP A1 - Uherek, Frantisek A1 - Chovan, Jozef A1 - Kuzma, Anton A1 - Pisecny, Pavol A1 - Hasko, Daniel A1 - Seyringer, Dana ED - Pudis, Dusan ED - Lettrichova, Ivana ED - Suslik, Lubos ED - Kovac, Jaroslav ED - Vincze, Andrej T1 - Silicon nanophotonics T2 - Proceedings of ADEPT 2013. 1st International Conference on Advances in Electronic and Photonic Technologies. Spa Novy Smokovec, High Tatras, Slovakia, June 2-5, 2013 Y1 - 2013 SN - 978-80-554-0689-3 PB - Univ. of Zilina CY - Zilina ER - TY - CHAP A1 - Schmidmayr, David A1 - Zehetner, Johann ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Quantum dots and organic fluorescent molecules for LED-based white-light generation T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 379 EP - 386 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - BOOK A1 - Mayer, Horst O. T1 - Interview und schriftliche Befragung. Grundlagen und Methoden empirischer Sozialforschung KW - +SSC 535 KW - Datensammlung, Interview : Empirische Sozialforschung Y1 - 2013 SN - 978-3-486-70691-8 PB - Oldenbourg CY - München ET - 6., überarb. Aufl. ER - TY - BOOK A1 - Wilms, Falko E. P. T1 - Über die Systemtheorie. Eine Metatheorie und ihre Anwendung T3 - Wandel und Kontinuität in Organisationen, 14 Y1 - 2013 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - JOUR A1 - Hemphill, Sheryl A. A1 - Schneider, Sharon T1 - Excluding students from school. A re-examination from a children’s rights perspective JF - The International Journal of Children's Rights KW - children’s rights KW - school exclusion KW - school suspension Y1 - 2013 U6 - http://dx.doi.org/10.1163/15718182-55680008 SN - 1571-8182 VL - 21. Jg. IS - H. 1 SP - 88 EP - 96 ER - TY - CHAP A1 - Matt, Hubert ED - Rudigier, Andreas ED - Grabher, Georg T1 - im umgang die kunst oder: zweimal der falsche ort T2 - buchstäblich vorarlberg Y1 - 2013 SP - 331 EP - 335 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Amann, Peter A1 - Huber, Gerhard A1 - Reißner, Joachim A1 - Petrasch, Jörg ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Domestic hot water heater for active demand side management and efficiency improvements T2 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg Y1 - 2013 SP - 2 EP - 9 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Kneidl, Michael A1 - Stebinger, Katrin ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Methoden zum Design von interaktiven Systemen T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2013 SN - 978-3-99018-253-6 SP - 109 EP - 128 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Jost, Patrick A1 - Kempter, Guido ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Interaktive Objektbeleuchtung. Ein Test in virtueller Realität T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2013 SN - 978990182536 SP - 93 EP - 108 PB - Bucher CY - Hohenems u.a. ER - TY - JOUR A1 - Matt, Hubert T1 - Ingo Springenschmid. Drei Skizzen zu den Initialen I. S. oder S. I. JF - miromente. Zeitschrift für Gut und Bös Y1 - 2013 VL - o.Jg. IS - Nr. 33 SP - 33 EP - 40 ER - TY - JOUR A1 - Jancsary, Peter M. T1 - Verstehen und Information JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2013 SN - 1610-8914 VL - 12. Jg. IS - H. 1 SP - 3 EP - 9 ER - TY - CHAP A1 - Kepplinger, Peter A1 - Huber, Gerhard A1 - Amann, Peter A1 - Rheinberger, Klaus A1 - Petrasch, Jörg T1 - Active demand side management with domestic hot water heaters using binary integer programming T2 - Nachhaltige Gebäude. Versorgung - Bewertung - Integration. e-nova. Internationaler Kongress 2013. 13. und 14. November 2013 Y1 - 2013 SN - 978-3-9502452-4-0 SP - 367 EP - 376 PB - Fachhochschule Burgenland CY - Pinkafeld ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Organisation JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2013 SN - 1610-8914 VL - 12. Jg. IS - H. 1 SP - 73 EP - 86 ER - TY - BOOK ED - Ilg, Markus ED - Ortner, Johannes T1 - Value Day 2013. Aktuelle Entwicklungen in Controlling, Finance & Strategy KW - +WAA 300 KW - +WBF 270 KW - +WBH 725 KW - Controlling : Allgemeines KW - Finanzwirtschaft KW - Strategisches Management Y1 - 2013 SN - 978-3-86573-689-5 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - BOOK ED - Kempter, Guido ED - Lofner, Hans-Jürgen T1 - Grenzenlos kooperieren. Forschung im Dialog mit Gesellschaft und Wirtschaft. Tagungsband zum 7. Forschungsforum der österreichischen Fachhochschulen. 03.-04. April 2013. FH Vorarlberg KW - +AWC 665 A KW - Fachhochschule : Österreich : Forschung und Entwicklung Y1 - 2013 SN - 978-3-86573-709-0 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Baumeister, Alexander A1 - Ilg, Markus ED - Rickards, Robert ED - Fang, Jianing T1 - Financial management and control of iterative software processes. Advances in similarity-based calculation methods T2 - Proceedings of the Annual International Conference on Accounting and Finance (AF 2013). Bangkok, 2013 KW - activity based costing KW - AGILE software development KW - COMPUTER software development KW - earned value method KW - FINANCIAL management KW - INTERNAL auditing KW - iterative software processes KW - management accounting KW - MANAGERIAL accounting KW - RESEARCH KW - unified process Y1 - 2013 SP - 33 EP - 38 PB - Global Science & Technology Forum CY - Singapore ER - TY - JOUR A1 - Friess, Hansmartin A1 - Haussener, Sophia A1 - Steinfeld, Aldo A1 - Petrasch, Jörg T1 - Tetrahedral mesh generation based on space indicator functions JF - International Journal for Numerical Methods in Engineering KW - flow in porous media KW - mesh generation KW - multiscale KW - Navier–Stokes Y1 - 2013 U6 - http://dx.doi.org/10.1002/nme.4419 SN - 1097-0207 VL - o.Jg. IS - Bd. 93, H. 10 SP - 1040 EP - 1056 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Die Lenkungswirkung der eigenen inneren Bilder. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2013 UR - http://trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/23218-problemloesungsprozesse-initiieren-die-lenkungswirkung-der-eigenen-inneren-bilder VL - o.Jg. IS - Nr. 80 ER - TY - CHAP A1 - Schumacher, Jens A1 - Maurer, Florian A1 - Dobler, Martin ED - Pawar, Kulwant S. ED - Rogers, Helen T1 - Enabling robustness through supply chain resilience T2 - Abstracts of papers presented at the 18th International Symposium on Logistics (ISL 2013). Resilient supply chains in an uncertain environment. Vienna, Austria 7-10th July 2013 Y1 - 2013 SN - 978-0-85358-292-2 SP - 35 EP - 36 PB - Nottingham University Business School CY - Nottingham ER - TY - CHAP A1 - King, Julian A1 - Koc, Helin A1 - Unterkofler, Karl A1 - Teschl, Gerald A1 - Teschl, Susanne A1 - Mochalski, Pawel A1 - Hinterhuber, Hartmann A1 - Amann, Anton ED - Amann, Anton ED - Smith, David T1 - Physiological modeling for analysis of exhaled breath T2 - Volatile biomarkers. Non-invasive diagnosis in physiology and medicine Y1 - 2013 SN - 978-0-444-62613-4 U6 - http://dx.doi.org/10.1016/B978-0-44-462613-4.00003-9 SP - 27 EP - 46 PB - Elsevier CY - Amsterdam u.a. ER - TY - CHAP A1 - Beyer, Hans-Georg A1 - Hellwig, Michael T1 - Controlling population size and mutation strength by Meta-ES under fitness noise T2 - FOGA XII. Proceedings of the twelfth ACM Workshop on Foundations of Genetic Algorithms KW - adaptation KW - evolution strategies KW - fitness noise KW - meta-es KW - mutation strength KW - population size KW - sphere model Y1 - 2013 SN - 978-1-4503-1990-4 SP - 11 EP - 24 PB - ACM CY - New York, NY ER - TY - JOUR A1 - Breuer, Thomas A1 - Csiszar, Imre T1 - Systematic stress tests with entropic plausibility constraints JF - Journal of Banking & Finance KW - Model risk KW - Multiple priors KW - Relative entropy KW - Risk measures KW - Scenario analysis KW - Worst case Y1 - 2013 U6 - http://dx.doi.org/10.1016/j.jbankfin.2012.04.013 SN - 0378-4266 VL - 37. Jg. IS - H. 5 SP - 1552 EP - 1559 ER - TY - JOUR A1 - Ludescher, Thomas A1 - Feilhauer, Thomas A1 - Brezany, Peter T1 - Cloud-based code execution framework for scientific problem solving environments JF - Journal of Cloud Computing KW - Computer Communication Networks KW - Information Systems Applications (incl. Internet) KW - Computer System Implementation KW - Computer Systems Organization and Communication Networks KW - Software Engineering/Programming and Operating Systems KW - Special Purpose and Application-Based Systems Y1 - 2013 U6 - http://dx.doi.org/10.1186/2192-113X-2-11 SN - 2192-113X VL - 2. Jg. IS - H. 1 ER - TY - CHAP A1 - Ludescher, Thomas A1 - Feilhauer, Thomas A1 - Amann, Anton A1 - Brezany, Peter ED - Perner, Petra T1 - Towards a high productivity automatic analysis framework for classification. An initial study T2 - Advances in data mining. Applications and theoretical aspects. 13th Industrial Conference, ICDM 2013. New York, NY, USA, July 16-21, 2013. Proceedings KW - Artificial Intelligence (incl. Robotics) KW - Image Processing and Computer Vision KW - Information Systems Applications (incl. Internet) KW - Automatic Analyse Framework KW - classification KW - clustering KW - Data Mining and Knowledge Discovery KW - Database Management KW - Multimedia Information Systems KW - prediction Y1 - 2013 SN - 978-3-642-39735-6 SN - 978-3-642-39736-3 SP - 25 EP - 39 PB - Springer CY - Berlin (u.a.) ER - TY - JOUR A1 - Mochalski, Pawel A1 - Sponring, Andreas A1 - King, Julian A1 - Unterkofler, Karl A1 - Troppmair, Jakob A1 - Amann, Anton T1 - Release and uptake of volatile organic compounds by human hepatocellular carcinoma cells (HepG2) in vitro JF - Cancer Cell International Y1 - 2013 U6 - http://dx.doi.org/10.1186/1475-2867-13-72 SN - 1475-2867 VL - 13. Jg. IS - H. 72 ER - TY - JOUR A1 - Mochalski, Pawel A1 - King, Julian A1 - Klieber, Martin A1 - Unterkofler, Karl A1 - Hinterhuber, Hartmann A1 - Baumann, Matthias A1 - Amann, Anton T1 - Blood and breath levels of selected volatile organic compounds in healthy volunteers JF - Analyst Y1 - 2013 U6 - http://dx.doi.org/10.1039/c3an36756h SN - 1364-5528 VL - 138. Jg. IS - H. 7 SP - 2134 EP - 2145 ER - TY - THES A1 - Ludescher, Thomas T1 - Towards high-productivity infrastructures for time-intensive scientific analysis KW - stylenotupdated Y1 - 2013 PB - Wien. Universität Wien ER - TY - JOUR A1 - Auchter, Eberhard A1 - Kriz, Willy Christian T1 - Gender aspects by using start-up simulations for entrepreneurship education results of theory-based evaluation studies JF - Journal of Asia Entrepreneurship and Sustainability Y1 - 2013 UR - http://www.asiaentrepreneurshipjournal.com/JAESMay2013SpecEd.pdf SN - 1176-8592 VL - 9. Jg. IS - H. 1 SP - 39 EP - 56 ER - TY - CHAP A1 - Breuer, Thomas ED - Zenil, Hector T1 - A Gödel-Turing perspective on quantum states indistinguishable from inside T2 - A computable universe. Understanding and exploring nature as computation Y1 - 2013 SP - 605 EP - 616 PB - World Scientific Publ. CY - New Jersey u.a. ER - TY - CHAP A1 - Teschl, Gerald A1 - Unterkofler, Karl ED - Holden, Helge ED - Simon, Barry ED - Teschl, Gerald T1 - Spectral theory as influenced by Fritz Gesztesy T2 - Spectral analysis, differential equations and mathematical physics. A festschrift in honor of Fritz Gesztesy's 60th birthday KW - 35P05, 34L40 (Primary) 34B20, 34B24 (Secondary) KW - Mathematical Physics KW - Mathematics - Spectral Theory Y1 - 2013 U6 - http://dx.doi.org/10.1090/pspum/087 SP - 341 EP - 364 PB - American Mathematical Society CY - Providence, RI ER - TY - JOUR A1 - Mochalski, Pawel A1 - King, Julian A1 - Unterkofler, Karl A1 - Amann, Anton T1 - Stability of selected volatile breath constituents in Tedlar, Kynar and Flexfilm sampling bags JF - Analyst Y1 - 2013 U6 - http://dx.doi.org/10.1039/c2an36193k SN - 1364-5528 VL - 138. Jg. IS - H. 5 SP - 1405 EP - 1418 ER - TY - CHAP A1 - Zehetner, Johann A1 - Stroj, Sandra A1 - Zanghellini, Gerhard T1 - Facilitating the fabrication of micron scale composite polymer inlays in ceramics substrates using femtosecond pulse laser ablation technique. [Poster] T2 - 12th International Conference on Laser Ablation (COLA 2013), 6 to 11 October 2013, Ischia, Italy Y1 - 2013 UR - https://www.fhv.at/fileadmin/user_upload/fhv/files/forschung/mikrotechnik/publikationen/2013/Poster_Cola2013.pdf ER - TY - CHAP A1 - Schumacher, Jens A1 - Maurer, Florian A1 - Dobler, Martin A1 - Haidukiewitz, Eva Kristin ED - Cheung, Jinghua ED - Song, Huan T1 - Robust supply chains. An immanent paradigm shift T2 - Logistics. Perspectives, approaches and challenges Y1 - 2013 SN - 978-1-62618-087-1 SP - 35 EP - 63 PB - Nova Publ. CY - New York, NY ER - TY - JOUR A1 - Jancsary, Peter M. A1 - Wilms, Falko E. P. T1 - Vom Unsinn des Sender-Empfänger-Modells. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2013 UR - http://www.trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/23059-vom-unsinn-des-sender-empfaenger-modells VL - o.Jg. IS - Nr. 79 SP - 23 EP - 24 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Ein Gespräch hat weder Sender noch Empfänger. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2013 UR - http://trainertreffen.de/index.php/online-journal-menue-journal/neuste-beitraege-menue-journal/147-kommunikation/22665-problemloesungsprozesse-initiieren-ein-gespraech-hat-weder-sender-noch-empfaenger VL - o.Jg. IS - Nr. 78 ER - TY - JOUR A1 - Elsayed, Ibrahim A1 - Ludescher, Thomas A1 - King, Julian A1 - Ager, Clemens A1 - Trosin, Michael A1 - Senocak, Uygar A1 - Brezany, Peter A1 - Feilhauer, Thomas A1 - Amann, Anton T1 - ABA-Cloud. Support for collaborative breath research JF - Journal of Breath Research Y1 - 2013 U6 - http://dx.doi.org/10.1088/1752-7155/7/2/026007 SN - 1752-7163 VL - 7. Jg. IS - H. 2 ER - TY - JOUR A1 - Buckley, Peter J. A1 - Horn, Sierk A1 - Cross, Adam R. A1 - Stillwell, John T1 - The spatial redistribution of Japanese direct investment in the United Kingdom between 1991 and 2010 JF - Business history Y1 - 2013 VL - 55. Jg. IS - H. 3 SP - 405 EP - 430 ER - TY - JOUR A1 - Horn, Sierk A. T1 - Interdisciplinary engagement as an acculturation process BT - the case of Japanese studies JF - Social science Japan journal Y1 - 2013 U6 - http://dx.doi.org/10.1093/ssjj/jyt014 VL - 16. Jg. IS - H. 2 SP - 251 EP - 277 ER - TY - JOUR A1 - Amann, Peter A1 - Cordin, Michael A1 - Redinger, Josef A1 - Stolwijk, Sebastian D. A1 - Zumbrägel, Karen A1 - Donath, Markus A1 - Bertel, Erminald A1 - Menzel, Alexander T1 - Circumstantial evidence for hydrogen-induced surface magnetism on Pd(110) JF - Physical Review B. Condensed matter and materials physics Y1 - 2012 VL - o.Jg. IS - Bd. 85, H. 9 ER - TY - CHAP A1 - Resch, Dörte A1 - Steinkellner, Peter ED - Heimerl, Peter ED - Sichler, Ralph T1 - Diskursive und Systemische Ansätze der Führung T2 - Strategie, Organisation, Personal, Führung KW - Diskursive und Systemische Ansätze der Führung KW - Doerte Resch Peter Steinkellner Y1 - 2012 SP - 533 EP - 558 PB - Facultas.WUV CY - Wien ER - TY - JOUR A1 - Cordin, Michael A1 - Amann, Peter A1 - Menzel, Alexander A1 - Bertel, Erminald A1 - Baranov, Mikhail A1 - Diehl, Sebastian A1 - Redinger, Josef A1 - Franchini, Cesare T1 - Comment on ‘Cleavage surface of the BaFe2−xCoxAs2 and FeySe1−xTex superconductors. A combined STM plus LEED study’ JF - Physical Review B. Condensed matter and materials physics Y1 - 2012 VL - o.Jg. IS - Bd. 86, H. 16 ER - TY - CHAP A1 - Wetzstein, Irmgard T1 - Die Krise in der öffentlichen Sommerdiskussion 2011. Eine Frame-Analyse anhand österreichischer Printmedien T2 - Wissen verwerten. 6. Forschungsforum der österreichischen Fachhochschulen. 11.-12. April 2012, FH Joanneum Graz. Tagungsband 3: Wirtschaftswissenschaften: Beiträge gegen die Krise Y1 - 2012 SP - 99 EP - 103 PB - FH Joanneum Eigenverl. CY - Graz ER - TY - CHAP A1 - Resch, Dörte A1 - Müller, Björn ED - Vicini, Sandro ED - Frischknecht, Ulrich T1 - Die Herausforderung von Beratungsarbeit als ständigem Balanceakt T2 - Entwicklungslinien der Beratung an Hochschulen KW - Die Herausforderung von Beratungsarbeit als ständigem Balanceakt KW - Doerte Resch Björn Müller Y1 - 2012 SP - 39 EP - 48 PB - Beratungsstellen der Berner und Zürcher Hochschulen CY - Bern ER - TY - CHAP A1 - Hellberg, Philipp von ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Reichhaltigkeit im Interface-Design T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2012 SP - 95 EP - 108 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Bartsch, Carsten A1 - Pfefferkorn, Reinhard A. ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Produktentwicklung im Wandel der Demographie T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2012 SP - 23 EP - 37 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Allgäuer-Hackl, Heinz A1 - Eder, Hans A1 - Schwab, Gerhard ED - Walz, Hans ED - Teske, Irmgard ED - Martin, Edi T1 - Entwicklung aus der Sicht der Anderen. Entwicklungsarbeit - Soziale Arbeit - Menschenrechte T2 - Menschenrechtsorientiert wahrnehmen - beurteilen - handeln. Ein Lese- und Arbeitsbuch für Studierende, Lehrende und Professionelle der Sozialen Arbeit Y1 - 2012 SP - 63 EP - 111 PB - Interact u.a. CY - Luzern ET - 2. Aufl. ER - TY - JOUR A1 - Tisserant, Jean-Nicolas A1 - Hany, Roland A1 - Partel, Stefan A1 - Bona, Gian-Luca A1 - Mezzenga, Raffaele A1 - Heier, Jakob T1 - Dewetting-driven hierarchical self-assembly of small semiconducting molecules JF - Soft Matter Y1 - 2012 U6 - http://dx.doi.org/10.1039/C2SM25288K VL - 8. Jg. IS - H. 21 SP - 5804 EP - 5810 ER - TY - CHAP A1 - Vanko, Gabriel A1 - Zehetner, Johann A1 - Choleva, Pavlina A1 - Lalinský, Tibor A1 - Hudek, Peter ED - Haščík, Štefan ED - Osvald, Jozef T1 - Laser ablation: a supporting technique to micromachining of SiC T2 - ASDAM 2012. Conference proceedings. The ninth international conference on advanced semiconductor devices and microsystems. Smolenice (Slovakia). November 11-15, 2012 Y1 - 2012 U6 - http://dx.doi.org/10.1109/ASDAM.2012.6418518 SP - 259 EP - 262 PB - IEE CY - Piscataway, NJ ER - TY - JOUR A1 - Partel, Stefan A1 - Mayer, Markus A1 - Motzek, Kristian T1 - In-situ measurement and characterization of photoresists during development JF - SPIE Newsroom Y1 - 2012 ER - TY - CHAP A1 - Seyringer, Dana A1 - Uherek, Frantisek A1 - Chovan, Jozef A1 - Kuzma, Anton ED - Haščík, Štefan ED - Osvald, Jozef T1 - Design, Simulation and Evaluation of AWG based demultiplexers T2 - ASDAM 2012. Conference proceedings. The ninth international conference on advanced semiconductor devices and microsystems. Smolenice (Slovakia). November 11-15, 2012 KW - arrayed waveguide gratings KW - AWG-Analyzer tool KW - wavelength division multiplexing KW - integrated optics KW - demultiplexing equipment KW - frequency 100 GHz KW - transmission characteristics KW - Apollo photonics KW - AWG-based demultiplexers KW - AWG-parameter layout KW - AWG-parameter tool KW - Loss measurement KW - low-index 8-channel optical demultiplexer KW - optical design KW - optical design techniques KW - Optiwave photonic tool KW - Photonics KW - R-soft photonic tool KW - Refractive index KW - Semiconductor device measurement KW - Wavelength measurement Y1 - 2012 U6 - http://dx.doi.org/10.1109/ASDAM.2012.6418537 SP - 303 EP - 306 PB - IEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kriz, Willy Christian ED - Smith, Alex ED - Hutchinson, David ED - Maryott, Kiersten ED - Rahn, David ED - Scherpereel, Chris ED - Teach, Dick T1 - Games for management simulation T2 - Developments in business simulation & experiential exercises. ABSEL 2012, San Diego, California. Conference proceedings Y1 - 2012 PB - Association for Business Simulation and Experiential Learning CY - Glenside, Pa ER - TY - CHAP A1 - Kempter, Guido T1 - Nutzerzentrierte Entwicklung von Steuerungskennlinien für dynamische Beleuchtung T2 - 6. DIN-Expertenforum. Wirkung des Lichts auf den Menschen. Kurzfassung der Vorträge 28. Juni 2012 Y1 - 2012 SP - 43 EP - 51 PB - Beuth CY - Berlin u.a. ER - TY - BOOK A1 - Alton-Scheidl, Roland A1 - Barth, Thomas T1 - Ethify Yourself 2.0. Ethisch Leben und Wirtschaften als Chance KW - +GPC 440 KW - Praktische Ethik Y1 - 2012 SN - 978-3-902157-97-3 PB - Edition Art Science CY - St. Wolfgang ER - TY - BOOK A1 - Hils, Claudio A1 - Renz, Peter A1 - Sayer, Walle A1 - Schmalriede, Manfred T1 - Abseits - aside - à'lécart KW - +KAB 491 KW - Hils, Claudio : Fotograph Y1 - 2012 SN - 978-3-86351-500-3 PB - Klöpfer & Meyer CY - Tübingen ER - TY - JOUR A1 - Kriz, Willy Christian T1 - Gaming simulation and ethics. Reflection on interconnections and implications JF - Studies in Simulation & Gaming Y1 - 2012 VL - 22. Jg. SP - 65 EP - 68 ER - TY - BOOK ED - Kempter, Guido ED - Weidmann, Karl-Heinz T1 - Technik für Menschen im nächsten Jahrzehnt. Beiträge zum Usability Day X, 1. Juni 2012 KW - +INC 310 KW - +INC 320 KW - Benutzerschnittstelle KW - Mensch-Maschine-Kommunikation Y1 - 2012 SN - 978-3-89967-802-4 PB - Pabst Science Publ. CY - Lengerich ER - TY - BOOK ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - design2product. Beiträge zur empirischen Designforschung T3 - design2product, 2 KW - +KDC 122 KW - Design : Theorie, Reflexion Y1 - 2012 SN - 978-3-99018-169-0 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Weidmann, Karl-Heinz A1 - Ritter, Walter A1 - King, Julian ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Zusammenhang physiologischer und mentaler Aktivitäten mit der Atemluft T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2012 SP - 51 EP - 61 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Weidmann, Karl-Heinz ED - Kempter, Guido ED - Weidmann, Karl-Heinz T1 - Die Zukunft liegt im Dunkeln - Vom Anwender zum Bedienten T2 - Technik für Menschen im nächsten Jahrzehnt. Beiträge zum Usability Day X. 1. Juni 2012 Y1 - 2012 SP - 67 EP - 71 PB - Pabst Science Publ. CY - Lengerich ER - TY - JOUR A1 - Akolkar, Anupam A1 - Petrasch, Jörg T1 - Tomography-based characterization and optimization of fluid flow through porous media JF - Transport in Porous Media KW - Civil Engineering KW - Classical Continuum Physics KW - Dupuit–Forchheimer KW - Fluid Flow KW - Geotechnical Engineering & Applied Earth Sciences KW - Hydrogeology KW - Industrial Chemistry/Chemical Engineering KW - Permeability KW - Porosity KW - Tomography Y1 - 2012 U6 - http://dx.doi.org/10.1007/s11242-012-0060-7 SN - 0169-3913 SN - 1573-1634 VL - 95. Jg. IS - H. 3 SP - 535 EP - 550 ER - TY - JOUR A1 - Finck, Steffen A1 - Beyer, Hans-Georg T1 - Performance analysis of the simultaneous perturbation stochastic approximation algorithm on the noisy sphere model JF - Theoretical Computer Science KW - Evolution strategy KW - Algorithm comparison KW - Noisy optimization KW - Stochastic gradient approximation Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.tcs.2011.11.015 SN - 0304-3975 VL - o.Jg. IS - Bd. 419 SP - 50 EP - 72 ER - TY - CHAP A1 - Göpfert, Ulrich T1 - Genauigkeitsuntersuchungen von spanenden Fertigungsprozessen T2 - Wissen verwerten. 6. Forschungsforum der österreichischen Fachhochschulen. 11.-12. April 2012, FH Joanneum Graz. Tagungsband 6: Intelligente Produktion im globalen Wettbewerb Y1 - 2012 SP - 21 EP - 25 PB - FH Joanneum Eigenverl. CY - Graz ER - TY - CHAP A1 - Beyer, Hans-Georg A1 - Finck, Steffen ED - Coello Coello, Carlos A. ED - Cutello, Vincenzo ED - Deb, Kalyanmoy ED - Forrest, Stephanie ED - Nicosia, Giuseppe ED - Pavone, Mario T1 - HappyCat – A simple function class where well-known direct search algorithms do fail T2 - Parallel Problem Solving from Nature - PPSN XII. 12th International Conference. Taormina, Italy, September 2012. Proceedings, Part I KW - Algorithm Analysis and Problem Complexity KW - Artificial Intelligence (incl. Robotics) KW - Discrete Mathematics in Computer Science KW - Pattern Recognition KW - Computation by Abstract Devices KW - Computational Biology/Bioinformatics Y1 - 2012 SN - 978-3-642-32936-4 SN - 978-3-642-32937-1 U6 - http://dx.doi.org/10.1007/978-3-642-32937-1_37 SP - 367 EP - 376 PB - Springer CY - Berlin u.a. ER - TY - CHAP A1 - Mayer, Horst O. A1 - Brachart, Cathrin ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Werbung mit BDSM-Motiven T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2012 SP - 81 EP - 94 PB - Bucher CY - Hohenems u.a. ER - TY - JOUR A1 - Wilms, Falko E. P. A1 - Jancsary, Peter M. T1 - Kernfähigkeiten des Dialogs JF - TrainerJournal Y1 - 2012 VL - o.Jg. IS - Nr. 76 ER - TY - CHAP A1 - Erickson, Ben A1 - Petrasch, Jörg T1 - Inverse identification of intensity distributions from multiple flux maps in concentrating solar applications T2 - Eurotherm Conference No. 95: Computational Thermal Radiation in Participating Media IV. Nancy, France, 18-20 April 2012 Y1 - 2012 U6 - http://dx.doi.org/10.1088/1742-6596/369/1/012014 SP - 12014 EP - 12023 ER - TY - JOUR A1 - Kriz, Willy Christian A1 - Eberle, Thomas T1 - Einsatz von Planspielen in Unternehmen JF - personal manager Y1 - 2012 VL - 11. Jg. IS - H. 1 SP - 34 EP - 36 ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Künz, Andreas ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Visualisierungstrends. 3D-Tendenzen. 3D-Rapid Prototyping. 3D Sehen und Erleben T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2012 SP - 39 EP - 49 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Reichl, Gernot A1 - Geiger, Franz T1 - Adaptive indirect fieldoriented control of an induction machine in the armature control range T2 - Wissen verwerten. 6. Forschungsforum der österreichischen Fachhochschulen. 11.-12. April 2012, FH Joanneum Graz. Tagungsband 6: Intelligente Produktion im globalen Wettbewerb Y1 - 2012 SP - 67 EP - 71 PB - FH Joanneum Eigenverl. CY - Graz ER - TY - CHAP A1 - Göpfert, Ulrich ED - Traussnigg, Udo T1 - Additive Manufacturing setzt neue Ziele für die Ausbildung T2 - Tag der Mechatronik 2012. Tagungsband. Graz, 22. September 2012, FH CAMPUS 02 Y1 - 2012 SP - 20 EP - 21 PB - Leykam CY - Graz ER - TY - JOUR A1 - Beyer, Hans-Georg A1 - Finck, Steffen T1 - On the design of constraint covariance matrix self-adaptation evolution strategies including a cardinality constraint JF - IEEE Transactions on Evolutionary Computation KW - linear programming KW - Mathematical model KW - Vectors KW - portfolio optimization KW - Algorithm design and analysis KW - algorithm engineering KW - cardinality constraint KW - CMSA-ES KW - concave programming KW - Constrained optimization KW - constraint covariance matrix self-adaptation evolution strategy design KW - Constraint optimization KW - covariance matrices KW - Covariance matrix KW - covariance matrix self-adaptation evolution strategy KW - Dow Jones Index KW - investment KW - linear inequalities KW - mixed linear-nonlinear constrained optimization problem KW - nonconvex optimization KW - nonconvex optimization problem KW - nonlinear programming KW - Portfolios KW - time series KW - time series data Y1 - 2012 U6 - http://dx.doi.org/10.1109/TEVC.2011.2169967 SN - 1089-778X VL - 16. Jg. IS - H. 4 SP - 578 EP - 596 ER - TY - BOOK A1 - Knubben, Thomas A1 - Hils, Claudio A1 - Braun, Uli T1 - Hölderlin. Eine Winterreise. Mit Bildern über Landschaften von Claudio Hils nach Fotografien von Thomas Knubben sowie historischen Abbildungen und Dokumenten gestaltet von Uli Braun KW - +GLE 241 HOL KW - Hölderlin, Friedrich : Sekundärliteratur Y1 - 2012 SN - 978-3-86351-022-0 PB - Klöpfer & Meyer CY - Tübingen ER - TY - CHAP A1 - Kempter, Guido A1 - Ritter, Walter ED - Schreier, Günter ED - Hayn, Dieter ED - Hörbst, Alexander ED - Ammenwerth, Elske T1 - Mobiles Messgerät für die Untersuchung des Lichteinflusses auf zirkadiane Rhythmen T2 - eHealth2012. Health Informatics meets eHealth - von der Wissenschaft zur Anwendung und zurück. Mobile Health & Care - Gesundheitsvorsorge immer und überall Y1 - 2012 SP - 21 EP - 26 PB - Österreichische Computer Gesellschaft CY - Wien ER - TY - CHAP A1 - Alton-Scheidl, Roland A1 - Benso, Joe A1 - Springer, Martin ED - Dulong de Rosnay, Melanie ED - Martin, Juan Carlos de T1 - The value of registering creative works T2 - The digital public domain. Foundations for an open culture Y1 - 2012 SP - 189 EP - 204 PB - OpenBook Publ. CY - Cambridge ER - TY - JOUR A1 - Auinger, Franz A1 - Kriz, Willy Christian T1 - Veränderungssituationen meistern. Planspiele fördern Change-Fähigkeiten von Führungskräften JF - Inovator. Das Magazin für Organisationsarbeit und Personalentwicklung Y1 - 2012 VL - o.Jg. IS - H. 21 SP - 6 EP - 10 ER - TY - CHAP A1 - Mayer, Horst O. A1 - Ammann, Agnes ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Dynamische Logos T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2012 SP - 63 EP - 80 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Eberharter, Johannes Karl A1 - Pfister, Thomas A1 - Öttl, Markus A1 - Amann, Robert ED - Steinbauer, Gerald ED - Uran, Suzana T1 - Trajectory Control for 3RPR Manipulators T2 - Proceedings of the Austrian Robotics Workshop 2012. Graz, Austria May 3rd and 4th 2012 Y1 - 2012 SP - 17 EP - 22 PB - Verl. der Technischen Univ. CY - Graz ER - TY - BOOK A1 - Beismann, Heike A1 - Bertling, Jürgen A1 - Beyer, Hans-Georg A1 - Boblan, Ivo A1 - Erb, Rainer A1 - Fischer, Markus A1 - Herdy, Michael A1 - Jordan, André A1 - Kesel, Antonia A1 - Menzel, Stephan A1 - Mörtl, Markus A1 - Pohl, Göran A1 - Seitz, Heike A1 - Speck, Olga A1 - Speck, Thomas A1 - Tesari, Iwiza A1 - Tschernjaew, Juri A1 - Wirth, Markus T1 - Bionik. Konzeption und Strategie. Abgrenzung zwischen bionischen und konventionellen Verfahren/Produkten. VDI 6220 T3 - VDI-Richtlinien ; VDI-Handbuch Bionik Y1 - 2012 PB - Verein Deutscher Ingenieure CY - Düsseldorf ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Künz, Andreas A1 - Kempter, Guido ED - Kempter, Guido ED - Weidmann, Karl-Heinz T1 - Technologische und psychologische Aspekte der virtuellen Realität T2 - Technik für Menschen im nächsten Jahrzehnt. Beiträge zum Usability Day X. 1. Juni 2012 Y1 - 2012 SP - 42 EP - 51 PB - Pabst Science Publ. CY - Lengerich ER - TY - CHAP A1 - Posch, Klaus A1 - Fredersdorf, Frederic T1 - Soziale Ungleichheit und soziales Kapital: Können in unserer Gesellschaft nur mehr die Schnellen, Reichen und Schönen überleben? T2 - Wissen verwerten. 6. Forschungsforum der österreichischen Fachhochschulen. 11.-12. April 2012, FH Joanneum Graz. Tagungsband 5: Soziale Ungleichheit und Soziales Kapital Y1 - 2012 SP - 7 EP - 13 PB - FH Joanneum Eigenverl. CY - Graz ER - TY - CHAP A1 - Fredersdorf, Frederic ED - Kempter, Guido ED - Weidmann, Karl-Heinz T1 - Ist der Hammer gut oder böse? Exemplarische Beherrschungsprobleme technischer Komplexität T2 - Technik für Menschen im nächsten Jahrzehnt. Beiträge zum Usability Day X. 1. Juni 2012 Y1 - 2012 SP - 101 EP - 106 PB - Pabst Science Publ. CY - Lengerich ER - TY - CHAP A1 - Fredersdorf, Frederic T1 - Exportmarkt Indien - Eine Studie zu Exportaktivitäten und -philosophien regionaler Wirtschaftsunternehmen T2 - Wissen verwerten. 6. Forschungsforum der österreichischen Fachhochschulen. 11.-12. April 2012, FH Joanneum Graz. Tagungsband 3: Wirtschaftswissenschaften: Beiträge gegen die Krise Y1 - 2012 SP - 17 EP - 21 PB - FH Joanneum Eigenverl. CY - Graz ER - TY - CHAP A1 - Seyringer, Dana ED - Jaworski, Marek ED - Marciniak, Marian T1 - Design and simulation of 128-channel 10 GHz AWG for ultra-dense wavelength division multiplexing T2 - ICTON 2012. 14th International Conference on Transparent Optical Networks. 2nd - 5th July, 2012. University of Warwick, Coventry, UK KW - 128-channel 10 GHz AWG design KW - 128-channel 10 GHz AWG simulation KW - arrayed waveguide grating KW - arrayed waveguide gratings KW - AWG-Analyzer tool KW - AWG-Parameters KW - Couplers KW - Crosstalk KW - frequency 10 GHz KW - high channel count AWG KW - insertion loss KW - narrow channel spacing AWG KW - Optical crosstalk KW - Optiwave software tool KW - Propagation losses KW - simulated transmission characteristics KW - stand-alone software tool KW - ultra-dense wavelength division multiplexing KW - ultra-DWDM KW - wavelength division multiplexing Y1 - 2012 U6 - http://dx.doi.org/10.1109/ICTON.2012.6253804 PB - National Institute of Telecommunications CY - Warschau ER - TY - CHAP A1 - Kempter, Guido A1 - Ritter, Walter A1 - Feuerstein, Gerhild T1 - Gesundheitsförderung durch Raumbeleuchtung T2 - Wissen verwerten. 6. Forschungsforum der österreichischen Fachhochschulen. 11.-12. April 2012, FH Joanneum Graz. Tagungsband 4: Multisektorale Gesundheitsförderung Y1 - 2012 SP - 59 EP - 63 PB - FH Joanneum Eigenverl. CY - Graz ER - TY - CHAP A1 - Kriz, Willy Christian ED - Gsöllpointner, Katharina T1 - Die Wirklichkeit spielen. Gaming Simulation in der Organisationsberatung T2 - Medien der Beratung. Ästhetik, Methoden, Praxis Y1 - 2012 SP - 129 EP - 142 PB - Facultas.WUV CY - Wien ER - TY - CHAP A1 - Kempter, Guido ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Quasi-experimentelle Lichtgestaltung T2 - design2product. Beiträge zur empirischen Designforschung ; 2 Y1 - 2012 SP - 109 EP - 127 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Jeschke, Sabina ED - Hauck, Eckart ED - Hees, Frank ED - Tilebein, Meike ED - Fischer, Thomas ED - Schwaninger, Thomas T1 - Zur Sozialkybernetik des direkten Gesprächs T2 - Interdisziplinarität und Komplexität. Konferenz für Wirtschafts- und Sozialkybernetik KyWi 2012 vom 28. bis 29. Juni 2012 in Aachen KW - +WBB 136 KW - +WBF 280 KW - Integriertes Management KW - Wirtschaftskybernetik Y1 - 2012 SP - 67 EP - 76 PB - Duncker und Humblot CY - Berlin ER - TY - CHAP A1 - Hefel, Johanna A1 - Roux, Pascale A1 - Walter, Wolfgang A1 - Wetzstein, Irmgard T1 - Arbeitsmarktintegration und Ressourcenorientierung T2 - Wissen verwerten. 6. Forschungsforum der österreichischen Fachhochschulen. 11.-12. April 2012, FH Joanneum Graz. Tagungsband 5: Soziale Ungleichheit und Soziales Kapital Y1 - 2012 SP - 51 EP - 55 PB - FH Joanneum Eigenverl. CY - Graz ER - TY - JOUR A1 - Jancsary, Peter M. A1 - Wilms, Falko E. P. T1 - Dialog und Beratung JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2012 VL - 11. Jg. IS - H. 1 SP - 43 EP - 51 ER - TY - JOUR A1 - Motzek, Kristian A1 - Partel, Stefan A1 - Bramati, Arianna A1 - Hofmann, Ulrich A1 - Unal, Nezih A1 - Hennemeyer, Marc A1 - Hornung, Michael A1 - Heindl, Alexander A1 - Ruhland, Michael A1 - Erdmann, Andreas A1 - Hudek, Peter T1 - Mask aligner lithography simulation - from lithography simulation to process validation JF - Microelectronic Engineering KW - Dissolution rate monitor KW - Mask aligner KW - Optical lithography KW - Photoresist KW - Proximity printing Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.mee.2012.07.076 SN - 0167-9317 VL - o.Jg. IS - Bd. 98 SP - 121 EP - 124 ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Wilms, Falko E. P. T1 - Wirkungsgefüge? T2 - Wirkungsgefüge. Einsatzmöglichkeiten und Grenzen in der Unternehmensführung Y1 - 2012 SP - 9 EP - 20 PB - Haupt CY - Bern u.a. ER - TY - BOOK ED - Wilms, Falko E. P. T1 - Wirkungsgefüge. Einsatzmöglichkeiten und Grenzen in der Unternehmensführung KW - +WBF 320 KW - Entscheidungstheorie, Problemlösung Y1 - 2012 SN - 978-3-258-07755-0 PB - Haupt CY - Bern u.a. ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Das direkte zwischenmenschliche Gespräch JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2012 VL - 11. Jg. IS - H. 2 SP - 119 EP - 126 ER - TY - BOOK A1 - Brettel, Malte A1 - Dittmann, Uwe A1 - Englberger, Hermann A1 - Hirschhausen, Christian von A1 - Leipnitz-Ponto, Yvonne A1 - Olsowski, Gunter A1 - Schätter, Alfred A1 - Schmager, Burkhardt A1 - Schuchardt, Christian T1 - Qualifikationsrahmen Wirtschaftsingenieurwesen Y1 - 2012 PB - FFBT Wirtschaftsingenieurwesen CY - Pforzheim ER - TY - CHAP A1 - Kriz, Willy Christian ED - Schwägele, Sebastian ED - Zürn, Birgit ED - Trautwein, Friedrich T1 - Der Deutsche Planspielpreis - Planspielforschung im Spannungsfeld zwischen ‚Analytischer Wissenschaft‘ und ‚Design Wissenschaft‘ T2 - Planspiele - Trends in der Forschung. Rückblick auf den deutschen Planspielpreis 2011 Y1 - 2012 SP - 139 EP - 146 PB - Books on demand CY - Norderstedt ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Auchter, Eberhard ED - Bielecki, Witold ED - Gandziarowska-Ziołecka, Jagoda ED - Pikos, Anna ED - Wardaszko, Marcin T1 - Gender effects in simulation games for entrepreneurship education T2 - Bonds & Bridges. Facing the challenges of the globalizing world with the use of simulation and gaming Y1 - 2012 SP - 127 EP - 140 PB - Poltext CY - Warsaw ER - TY - BOOK ED - Mair, Michael ED - Brezowar, Gabriela ED - Olsowski, Gunter ED - Zumbach, Jörg T1 - Problem-Based Learning im Dialog. Anwendungsbeispiele und Forschungsergebnisse aus dem deutschsprachigen Raum KW - +SEC 412 POL KW - Problemorientiertes Lernen Y1 - 2012 SN - 978-3-7089-0916-5 PB - Facultas.WUV CY - Wien ER - TY - CHAP A1 - Kempter, Guido A1 - Hellberg, Philipp von A1 - Miler, Christoph ED - Kempter, Guido ED - Weidmann, Karl-Heinz T1 - Zusammenwirken alter und neuer Technik T2 - Technik für Menschen im nächsten Jahrzehnt. Beiträge zum Usability Day X. 1. Juni 2012 Y1 - 2012 SP - 92 EP - 100 PB - Pabst Science Publ. CY - Lengerich ER - TY - CHAP A1 - Mayer, Brigitte ED - Gruber, Hans ED - Mayer, Brigitte T1 - Wissenschaftliche Schreibkompetenz. Erhebung der studentischen Schreibkompetenz in den betriebswirtschaftlichen Studiengängen der FHV T2 - Wissenschaftliches Schreiben an Hochschulen. Prozess, Produkt und Betreuung Y1 - 2012 SP - 61 EP - 99 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - BOOK ED - Gruber, Hans ED - Mayer, Brigitte T1 - Wissenschaftliches Schreiben an Hochschulen. Prozess, Produkt und Betreuung T3 - Wandel und Kontinuität in Organisationen, 13 Y1 - 2012 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Wilms, Falko E. P. T1 - Resümee T2 - Wirkungsgefüge. Einsatzmöglichkeiten und Grenzen in der Unternehmensführung Y1 - 2012 SP - 211 EP - 214 PB - Haupt CY - Bern u.a. ER - TY - CHAP A1 - Kriz, Willy Christian ED - Schwägele, Sebastian ED - Zürn, Birgit ED - Trautwein, Friedrich T1 - Systemorientiertes Management mit Planspielszenarien erlernen T2 - Planspiele. Lernen im Methoden-Mix. Integrative Lernkonzepte in der Diskussion Y1 - 2012 SP - 49 EP - 78 PB - Books on demand CY - Norderstedt ER - TY - JOUR A1 - Petrasch, Jörg A1 - Klausner, James T1 - Integrated solar thermochemical cycles for energy storage and fuel production JF - Wiley Interdisciplinary Reviews (WIREs). Energy and Environment Y1 - 2012 VL - 1. Jg. IS - H. 3 SP - 347 EP - 361 ER - TY - JOUR A1 - Singh, Abhishek A1 - Al-Raqom, Fotouh A1 - Klausner, James A1 - Petrasch, Jörg T1 - Production of hydrogen via an iron/iron oxide looping cycle: thermodynamic modeling and experimental validation JF - International Journal of Hydrogen Energy KW - Coal KW - Hydrogen KW - Iron oxide KW - Looping cycle KW - Syngas KW - Thermochemical Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.ijhydene.2012.01.074 VL - 37. Jg. IS - H. 9 SP - 7442 EP - 7450 ER - TY - CHAP A1 - Schumacher, Jens A1 - Dobler, Martin A1 - Haidukiewitz, Kristin A1 - Maurer, Florian ED - Pawar, Kulwant S. ED - Potter, Andrew T. T1 - Ways to develop a robust supply chain T2 - Proceedings of papers of the 17th International Symposium on Logistics (ISL 2012). New horizons in logistics and supply chain management. Cape Town, South Africa 8-11th July 2012 Y1 - 2012 SP - 46 EP - 54 PB - Nottinhham University Business School CY - Nottingham ER - TY - BOOK ED - Ilg, Markus ED - Puhr, Rainer T1 - Value Day 2012. Aktuelle Entwicklungen in Controlling, Finance & Strategy KW - +WAA 300 KW - +WBF 270 KW - +WBH 725 KW - Controlling : Allgemeines KW - Finanzwirtschaft KW - Strategisches Management Y1 - 2012 SN - 978-3-86573-649-9 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - JOUR A1 - Breuer, Thomas A1 - Jandačka, Martin A1 - Mencía, Javier A1 - Summer, Martin T1 - A systematic approach to multi-period stress testing of portfolio credit risk JF - Journal of Banking & Finance KW - Credit risk KW - Maximum loss KW - Stress testing KW - Worst case search Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.jbankfin.2011.07.009 SN - 0378-4266 VL - 36. Jg. IS - H. 2 SP - 332 EP - 340 ER - TY - JOUR A1 - King, Julian A1 - Unterkofler, Karl A1 - Teschl, Gerald A1 - Teschl, Susanne A1 - Mochalski, Paweł A1 - Koc, Helin A1 - Hinterhuber, Hartmann A1 - Amann, Anton T1 - A modeling-based evaluation of isothermal rebreathing for breath gas analyses of highly soluble volatile organic compounds JF - Journal of Breath Research Y1 - 2012 U6 - http://dx.doi.org/10.1088/1752-7155/6/1/016005 SN - 1752-7163 VL - 6. Jg. IS - H. 1 ER - TY - CHAP A1 - Ludescher, Thomas A1 - Feilhauer, Thomas A1 - Brezany, Peter ED - O'Conner, Lisa T1 - Security concept and implementation for a cloud based e-science infrastructure T2 - ARES 2012. Seventh international conference on availability, reliability and security. 20.-24. August 2012. Prague, Czech Republic. Proceedings KW - Authentication KW - breath gas analysis community KW - client authentication KW - cloud based analysis KW - cloud based e-science infrastructure KW - cloud computing KW - cloud-based code execution framework KW - cryptographic protocols KW - Databases KW - EC2 compatible cloud infrastructures KW - forward Kerberos tickets KW - heterogeneous distributed e-science infrastructures KW - IP networks KW - Kerberos-based security concept KW - large-scale collaborations KW - medical computing KW - message authentication KW - pneumodynamics KW - scientific private data KW - security credential injection KW - Servers KW - user authentication KW - virtual machines KW - VM-instances Y1 - 2012 SP - 280 EP - 285 PB - CPS CY - Los Alamitos, Calif. u.a. ER - TY - CHAP A1 - King, Julian A1 - Unterkofler, Karl A1 - Teschl, Susanne A1 - Amann, Anton A1 - Teschl, Gerald ED - Backfrieder, Werner ED - Bruzzone, Agostino ED - Longo, Francesco ED - Novak, Vera ED - Rosen, Joseph T1 - Volatile organic compounds in exhaled breath: real-time measurements, modeling, and bio-monitoing applications T2 - The 1st international workshop on innovative simulation for health care. September 19-21 2012, Vienna, Austria. IWISH 2012 Y1 - 2012 SP - 139 EP - 144 PB - DIME Univ. di Genova CY - Genua ER - TY - CHAP A1 - Beyer, Hans-Georg A1 - Hellwig, Michael ED - Soule, Terence T1 - Mutation strength control by meta-ES on the sharp ridge T2 - GECCO 2012. Proceedings of the fourteenth international conference on genetic and evolutionary computation companion. July 7-11, 2012. Pennsylvania, USA KW - evolution strategies KW - meta-es KW - mutation strength KW - adaption KW - sharp ridge function Y1 - 2012 SN - 978-1-4503-1177-9 SP - 305 EP - 312 PB - ACM CY - New York, NY ER - TY - CHAP A1 - Elsayed, Ibrahim A1 - Ludescher, Thomas A1 - Wöhrer, Alexander A1 - Feilhauer, Thomas A1 - Brezany, Peter ED - Ali, Hesham ED - Shi, Yong ED - Khazanchi, Deepak ED - Lees, Michael ED - Albada, G. Dick van ED - Dongarra, Jack ED - Sloot, Peter M.A. ED - Dongarra, Jack T1 - Data life cycle management and analytics code execution strategies for the breath gas analysis domain T2 - Proceedings of the International Conference on Computational Science, ICCS 2012. A theory of data movement in parallel computations KW - Breath gas analysis KW - Code Execution KW - e-Science Study Reproducibility KW - Problem Solving Environment KW - Scientific Data Preservation KW - Scientific Dataspace Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.procs.2012.04.017 SP - 156 EP - 165 ER - TY - JOUR A1 - King, Julian A1 - Kupferthaler, Alexander A1 - Frauscher, Birgit A1 - Hackner, Heinz A1 - Unterkofler, Karl A1 - Teschl, Gerald A1 - Hinterhuber, Hartmann A1 - Amann, Anton A1 - Högl, Birgit T1 - Measurement of endogenous acetone and isoprene in exhaled breath during sleep JF - Physiological Measurement Y1 - 2012 U6 - http://dx.doi.org/10.1088/0967-3334/33/3/413 SN - 0967-3334 VL - 33. Jg. IS - H. 3 SP - 413 EP - 428 ER - TY - JOUR A1 - Mochalski, Paweł A1 - King, Julian A1 - Kupferthaler, Alexander A1 - Unterkofler, Karl A1 - Hinterhuber, Hartmann A1 - Amann, Anton T1 - Human blood and plasma partition coefficients for C4-C8 n-alkanes, isoalkanes, and 1-alkenes JF - International Journal of Toxicology KW - Humans KW - Adult KW - Air KW - Alkanes KW - Alkenes KW - Female KW - Gas Chromatography-Mass Spectrometry KW - Male KW - Middle Aged KW - Solid Phase Microextraction Y1 - 2012 U6 - http://dx.doi.org/10.1177/1091581812442689 VL - 31. Jg. IS - H. 3 SP - 267 EP - 275 ER - TY - JOUR A1 - King, Julian A1 - Mochalski, Pawel A1 - Unterkofler, Karl A1 - Teschl, Gerald A1 - Klieber, Martin A1 - Stein, Markus A1 - Amann, Anton A1 - Baumann, Matthias T1 - Breath isoprene: muscle dystrophy patients support the concept of a pool of isoprene in the periphery of the human body JF - Biochemical and Biophysical Research Communications KW - Duchenne muscular dystrophy KW - Exhaled breath analysis KW - Isoprene KW - Muscle Y1 - 2012 U6 - http://dx.doi.org/10.1016/j.bbrc.2012.05.159 SN - 0006-291X VL - o. Jg. IS - Bd. 423, H. 3 SP - 526 EP - 530 ER - TY - CHAP A1 - Meyer-Nieberg, Silja A1 - Beyer, Hans-Georg ED - Rozenberg, Grzegorz ED - Bäck, Thomas ED - Kok, Joost N. T1 - The dynamical systems approach - progress measures and convergence properties T2 - Handbook of natural computing KW - Artificial Intelligence (incl. Robotics) KW - Computational Intelligence KW - Nanotechnology KW - Quantum Information Technology, Spintronics KW - Systems Biology KW - Theory of Computation Y1 - 2012 SP - 741 EP - 814 PB - Springer CY - Berlin u.a. ER - TY - JOUR A1 - Fredersdorf, Frederic A1 - Roux, Pascale T1 - Evaluation ambulant betreuter Wohnformen des Vereins DOWAS JF - soziales_kapital. Wissenschaftliches Journal österreichischer Fachhochschul-Studiengänge Soziale Arbeit Y1 - 2012 UR - http://www.soziales-kapital.at/index.php/sozialeskapital/article/view/235 SN - 2070-3481 VL - o.Jg. IS - Nr. 8 ER - TY - JOUR A1 - Fredersdorf, Frederic T1 - Evaluation zur Förderung von Sozialem Kapital JF - soziales_kapital. Wissenschaftliches Journal österreichischer Fachhochschul-Studiengänge Soziale Arbeit Y1 - 2012 UR - http://www.soziales-kapital.at/index.php/sozialeskapital/article/view/236 SN - 2070-3481 VL - o.Jg. IS - Nr. 8 ER - TY - CHAP A1 - Dobler, Martin A1 - Schumacher, Jens T1 - Intelligent cargo and logistics service platforms T2 - The technology of complex systems. Handlungskompetenz for a better environment, life, and future possibilities for humanity. SDPS-2012 Y1 - 2012 UR - https://www.sdpsnet.org/sdps/index.php/publications-list/sdps-conference-proceedings SP - 373 EP - 377 PB - SDPS CY - Dallas, Tex ER - TY - JOUR A1 - Boehler, Doris A1 - Randall, Matthew T1 - Diversity training and social work. An insight into theory, methodology and practice JF - ERIS web journal Y1 - 2012 UR - http://periodika.osu.cz/eris/dok/2012-01/03_diversity_training_and_social_work.pdf VL - o. Jg. IS - Nr. 1 SP - 15 EP - 25 ER - TY - JOUR A1 - Fredersdorf, Frederic T1 - Empirische Sozialforschung an sozialarbeiterischen Studiengängen österreichischer Fachhochschulen JF - Zeitschrift für Hochschulentwicklung (ZFHE) Y1 - 2012 UR - http://www.zfhe.at/index.php/zfhe/article/view/403 SN - 2219-6994 VL - 7. Jg. IS - Nr. 2 SP - 80 EP - 98 ER - TY - JOUR A1 - Jancsary, Peter M. A1 - Wilms, Falko E. P. T1 - Verweilen im Hier und Jetzt. Demonstriert am konkreten Beispiel Evaluation der akademischen Lehre. Problemlösungsprozesse initiieren JF - TrainerJournal Y1 - 2012 UR - https://www.trainertreffen.de/index.php/journal-mainmenue/147-kommunikation/22446-problemloesungsprozesse-verweilen-im-hier-und-jetzt VL - o.Jg. IS - Nr. 77 SP - 23 ER - TY - JOUR A1 - Posch, Klaus A1 - Fredersdorf, Frederic T1 - Sozialarbeitswissenschaft in Österreich. Eine Zwischenbilanz JF - soziales_kapital. Wissenschaftliches Journal österreichischer Fachhochschul-Studiengänge Soziale Arbeit Y1 - 2012 UR - http://www.soziales-kapital.at/index.php/sozialeskapital/article/view/234 VL - o.Jg. IS - Nr. 8 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Möglichkeiten des semi-virtuellen Studierens JF - Die Neue Hochschule DNH Y1 - 2012 UR - https://www.hlb.de/die-neue-hochschule VL - o.Jg. IS - H. 4 SP - 122 EP - 126 ER - TY - JOUR A1 - Buckley, Peter J. A1 - Cross, Adam R. A1 - Horn, Sierk A. T1 - Japanese foreign direct investment in India: An institutional theory approach JF - Business History Y1 - 2012 U6 - http://dx.doi.org/10.1080/00076791.2012.683417 VL - 54 IS - 5 SP - 657 EP - 688 ER - TY - CHAP A1 - Meermann, Axel A1 - Günther, Heinz ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Marke und Verpackungsgestaltung. Starke Marke contra Markenordnung und Markenarchitektur T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 105 EP - 115 PB - Bucher CY - Hohenems u.a. ER - TY - BOOK A1 - Wetzstein, Irmgard T1 - Mediativer Journalismus. Konstruktive Konfliktbearbeitung in der qualitätsjournalistischen Auslandsberichterstattung. Dissertation an der Universität Wien KW - +IKA 770 KW - +SPC 680 KW - Konfliktlösung : Sozialpsychologie KW - Publizistik : Nachrichtenwesen Y1 - 2011 SN - 978-3-531-18310-7 PB - VS Verl. für Sozialwissenschaften CY - Wiesbaden ER - TY - JOUR A1 - Brantner, Cornelia A1 - Lobinger, Katharina A1 - Wetzstein, Irmgard T1 - Effects of visual framing on emotional responses and evaluations of news stories about the Gaza conflict 2009 JF - Journalism & Mass Communication Quarterly Y1 - 2011 VL - 88. Jg. IS - H. 3 SP - 523 EP - 540 ER - TY - CHAP A1 - Lalinsky, Tibor A1 - Hudek, Peter A1 - Vanko, Gabriel A1 - Choleva, Pavlina A1 - Vallo, Martin A1 - Drzik, Milan A1 - Dzuba, Jaroslav A1 - Kutis, Vladimir A1 - Matay, Ladislav A1 - Kostic, Ivan T1 - Micromachined pressure sensors based on AlGaN/GaN circular HEMT sensing devices. Poster T2 - MNE 2011 (Micro- and Nano Engineering Conference), Berlin, Germany, September 19 – 23, 2011 Y1 - 2011 ER - TY - CHAP A1 - Walter, Wolfgang ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Zielgruppenanalyse in der Designforschung T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 157 EP - 171 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Hils, Claudio A1 - Petzold, Thomas ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Räumliche Strukturen zur Verbesserung der Akustik T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 141 EP - 154 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Motzek, Kristian A1 - Partel, Stefan A1 - Vogler, Uwe A1 - Erdmann, Andreas ED - Smith, Daniel G. ED - Wyrowski, Frank ED - Erdmann, Andreas T1 - Numerical optimization of illumination and mask layout for the enlargement of process windows and for the control of photoresist profiles in proximity printing T2 - Physical Optics. Marseille, France, 5 - 6 September 2011 Y1 - 2011 VL - 8171 PB - Society of Photo-Optical Instrumentation Engineers SPIE CY - Bellingham, Wash. ER - TY - JOUR A1 - Partel, Stefan A1 - Mayer, Markus A1 - Hudek, Peter A1 - Dincer, Can A1 - Kieninger, Jochen A1 - Urban, Gerhard A. A1 - Motzek, Kristian A1 - Matay, Ladislav T1 - Fabrication process development for a high sensitive electrochemical IDA sensor JF - Microelectronic Engineering Y1 - 2011 U6 - http://dx.doi.org/10.1016/j.mee.2012.03.028 SN - 0167-9317 VL - o.Jg. IS - Bd. 97 SP - 235 EP - 240 ER - TY - CHAP A1 - Mayer, Markus A1 - Partel, Stefan A1 - Schneider, Reinhard T1 - In-Situ-Messsystem zur Ermittlung der Entwicklungsraten von Photolacken T2 - 5. Forschungsforum der österreichischen Fachhochschulen. 27.-28. April 2011, FH Campus Wien. Tagungsband Y1 - 2011 SP - 256 EP - 259 PB - FH Campus Wien CY - Wien ER - TY - CHAP A1 - Seyringer, Dana A1 - Schmid, Patrick ED - Mazuray, Laurent ED - Wartmann, Rolf ED - Wood, Andrew ED - Tissot, Jean-Luc M. ED - Raynor, Jeffrey M. T1 - A new software tool is developed to evaluate the measured/simulated transmission characteristics of optical multiplexers/demultiplexers T2 - Optical Design and Engineering IV. 5–8 September 2011, Marseille, France Y1 - 2011 VL - 8167 PB - Society of Photo-Optical Instrumentation Engineers SPIE CY - Bellingham, Wash. ER - TY - CHAP A1 - Kuzma, Anton A1 - Chovan, Jozef A1 - Uherek, Frantisek A1 - Seyringer, Dana ED - Jeřábek, Vítězslav ED - Vodrážka, Jiří ED - Zvánovec, Stanislav T1 - Design and simulation of planar passive optical MMI splitters T2 - 23th Conference and Exhibition on Optical Communications 2011. Optics from Mb/s to Tb/s. Scientific section proceedings. October 20-21, 2011, Prague, Czech Republic Y1 - 2011 SP - 97 EP - 99 PB - Agentura Action M CY - Praha ER - TY - CHAP A1 - Seyringer, Dana A1 - Bielik, Michal A1 - Kytka, Milan ED - Pudis, Dusan ED - Kubicova, Ivana ED - Bury, Peter T1 - Introduction of a new software tool to design arrayed waveguide gratings T2 - Proceedings of the 17th international conference on applied physics of condensed matters, APCOM 2011 Y1 - 2011 SP - 122 EP - 125 PB - Univ. of Zilina CY - Zilina, Slovak Republic ER - TY - CHAP A1 - Finck, Steffen A1 - Beyer, Hans-Georg A1 - Melkozerov, Alexander ED - Krasnogor, Natalio ED - Lanzi, Pier Luca T1 - Noisy optimization. A theoretical strategy comparison of ES, EGS, SPSA & IF on the noisy sphere T2 - GECCO 2011. Genetic and evolutionary computation conference. July 12 - 16, 2011, Dublin, Ireland. A recombination of the 20th international conference on genetic algorithms (ICGA) and the 16th genetic programming conference (GP) Y1 - 2011 SP - 813 EP - 820 PB - ACM CY - New York, NY ER - TY - CHAP A1 - Kempter, Guido A1 - Herburger, Martin A1 - Ess, Nikolaus ED - Feuerstein, Gerhild ED - Ritter, Walter T1 - Neue Einsatzmöglichkeiten von Gebäudetechnologien in betreubaren Seniorenwohnungen T2 - Intelligent Wohnen. Zusammenfassung der Beiträge zum Usability Day IX. 20. Mai 2011 Y1 - 2011 SP - 46 EP - 52 PB - Pabst Science Publ. CY - Lengerich u.a. ER - TY - JOUR A1 - Ilg, Markus A1 - Baumeister, Alexander T1 - Performance management in software engineering JF - International Journal of Information Technology Project Management Y1 - 2011 VL - 2. Jg. IS - H. 1 ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Roux, Pascale A1 - Lorünser, Daniela T1 - Soziales Monitoring für Sozialkapital und Bürgerschaftliches Engagement T2 - 5. Forschungsforum der österreichischen Fachhochschulen. 27.-28. April 2011, FH Campus Wien. Tagungsband Y1 - 2011 SP - 202 EP - 205 PB - FH Campus Wien CY - Wien ER - TY - CHAP A1 - Weidmann, Karl-Heinz ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Apps Evaluierung mit TIPI. Touch-Interface-Prototype-Interactionlogger für mobile Geräte T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 129 EP - 139 PB - Bucher CY - Hohenems u.a. ER - TY - BOOK ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - design2product. Beiträge zur empirischen Designforschung T3 - Design2product - 1 KW - +KDC 122 KW - Design : Theorie, Reflexion Y1 - 2011 SN - 978-3-99018-095-2 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Ilg, Markus A1 - Baumeister, Alexander ED - Fang, Jianing T1 - Risk-return-management for non-finance-businesses. Value based risk reporting and management control of business units T2 - Proceedings of the Annual International Conference on Accounting and Finance (AF 2011). 23-24 May 2011, Singapore Y1 - 2011 PB - Global Science & Technology Forum CY - Singapore ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Kollaboratives Lernen mit Wikis JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2011 VL - 10. Jg. IS - H. 2 SP - 87 EP - 99 ER - TY - BOOK A1 - Beismann, Heike A1 - Bertling, Jürgen A1 - Beyer, Hans-Georg A1 - Boblan, Ivo A1 - Erb, Rainer A1 - Fischer, Markus A1 - Herdy, Michael A1 - Jordan, André A1 - Kesel, Antonia A1 - Menzel, Stephan A1 - Mörtl, Markus A1 - Pohl, Göran A1 - Seitz, Heike A1 - Speck, Olga A1 - Speck, Thomas A1 - Tesari, Iwiza A1 - Tschernjaew, Juri A1 - Wirth, Markus T1 - Bionik. Konzeption und Strategie. Abgrenzung zwischen bionischen und konventionellen Verfahren/Produkten. VDI 6220. Entwurf T3 - VDI-Richtlinien ; VDI-Handbuch Bionik Y1 - 2011 PB - Verein Deutscher Ingenieure CY - Düsseldorf ER - TY - CHAP A1 - Kneidl, Michael ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Clusteranalyse zur Bedeutungsanalyse von Piktogrammen T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 97 EP - 103 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Alton-Scheidl, Roland ED - Tschmuk, Peter T1 - Das Innovationspotenzial der Creative-Commons-Lizenzierung für Geschäftsmodelle in der Musikwirtschaft T2 - Focus Musik. Neue Töne der Musikwirtschaft Y1 - 2011 SP - 39 EP - 41 PB - departure wirtschaft, kunst und kultur gmbh CY - Wien ER - TY - JOUR A1 - Jancsary, Peter M. T1 - Selbstwahrnehmung als Basis der Kommunikation JF - SEMRADAR. Zeitschrift für Systemdenken und Entscheidungsfindung im Management Y1 - 2011 VL - 10. Jg. IS - H. 2 SP - 55 EP - 64 ER - TY - JOUR A1 - Wilms, Falko E. P. T1 - Kollaboratives Lernen mit Wikis JF - Die Neue Hochschule DNH Y1 - 2011 VL - o.Jg. IS - H. 4-5 SP - 184 EP - 188 ER - TY - JOUR A1 - Duden, Antje T1 - Trust and leadership. Learning culture in organizations JF - IJMC. International Journal of Management Cases Y1 - 2011 VL - 13. Jg. IS - H. 4 SP - 218 EP - 223 ER - TY - BOOK A1 - Beyer, Hans-Georg A1 - Edler, Jan A1 - Herdy, Michael A1 - Santibanez Koref, Ivan A1 - Olhofer, Markus A1 - Rudolph, Günter A1 - Sachs, Wolfgang A1 - Schliewe, S. A1 - Seitz, Heike A1 - Tesari, Iwiza T1 - Bionische Optimierung. Anwendung biologischer Wachstumsgesetze zur strukturmechanischen Optimierung technischer Bauteile. VDI 6224. Blatt 2. Entwurf T3 - VDI-Richtlinien ; VDI-Handbuch Bionik Y1 - 2011 PB - Verein Deutscher Ingenieure CY - Düsseldorf ER - TY - BOOK A1 - Beyer, Hans-Georg A1 - Edler, Jan A1 - Herdy, Michael A1 - Santibanez Koref, Ivan A1 - Olhofer, Markus A1 - Rudolph, Günter A1 - Sachs, Wolfgang A1 - Schliewe, S. A1 - Seitz, Heike A1 - Tesari, Iwiza T1 - Bionische Optimierung. Evolutionäre Algorithmen in der Anwendung. VDI 6224. Blatt 1. Entwurf T3 - VDI-Richtlinien ; VDI-Handbuch Bionik Y1 - 2011 PB - Verein Deutscher Ingenieure CY - Düsseldorf ER - TY - BOOK ED - Beyer, Hans-Georg ED - Langdon, William B. T1 - FOGA'11. Proceedings of the 2011 ACM/SIGEVO foundations of genetic algorithms XI. January 5-9, 2011. Schwarzenberg, Austria KW - +INC 365 EVA KW - +INC 371 MAL KW - Evolutionärer Algorithmus KW - Maschinelles Lernen Y1 - 2011 SN - 978-1-4503-0633-1 PB - ACM CY - New York, NY ER - TY - CHAP A1 - Ritter, Walter A1 - Rumen, Filkov A1 - Künz, Andreas A1 - Dontschewa, Miglena T1 - Messwerte von einfachen Raumsensoren als Indikatoren für Benutzerverhalten T2 - Intelligent Wohnen. Zusammenfassung der Beiträge zum Usability Day IX. 20. Mai 2011 Y1 - 2011 SP - 179 EP - 185 PB - Pabst Science Publ. CY - Lengerich u.a. ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Roux, Pascale ED - Markowitsch, Jörg ED - Gruber, Elke ED - Lassnigg, Lorenz ED - Moser, Daniela T1 - Die Balanced Scorecard als Medium eigenständiger Organisationsentwicklung von Berufsschulen – Evaluation eines Modellprojekts T2 - Turbulenzen auf Arbeitsmärkten und in Bildungssystemen. Beiträge zur Berufsbildungsforschung. Tagungsband der 2. Österreichischen Konferenz für Berufsbildungsforschung, 8./9. Juli 2010, Museum Arbeitswelt Steyr Y1 - 2011 SP - 150 EP - 165 PB - Studienverl. CY - Innsbruck u.a. ER - TY - CHAP A1 - Kriz, Willy Christian ED - Kriz, Willy Christian T1 - Planspiele für die Personalentwicklung T2 - Planspiele für die Personalentwicklung Y1 - 2011 SP - 11 EP - 22 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Mayrhofer, Markus A1 - Kempter, Guido A1 - Ritter, Walter T1 - Subjective visual impression of illumination quality from white LED operated by current-sources having different modulation T2 - LED Lighting Technologies. International winning approaches. LED professional Symposium + Expo. LpS 2011. 27.-29. September 2011, Bregenz Y1 - 2011 SP - 178 EP - 181 PB - Luger Research CY - Dornbirn ER - TY - CHAP A1 - Kriz, Willy Christian ED - Hitzler, Sebastian ED - Zürn, Birgit ED - Trautwein, Friedrich T1 - Qualitätskriterien von Planspielanwendungen T2 - Planspiele – Qualität und Innovation. Neue Ansätze aus Theorie und Praxis. Stuttgart: DHBW Y1 - 2011 SP - 11 EP - 37 PB - DHBW CY - Stuttgart ER - TY - CHAP A1 - Weber, Heidi ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Designtheorie versus Designpraxis T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 11 EP - 26 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Wilms, Falko E. P. ED - Tilebein, Meike T1 - Dialog als Kunst, gemeinsam zu denken T2 - Innovation und Information. Wissenschaftliche Jahrestagung der Gesellschaft für Wirtschafts- und Sozialkybernetik vom 3. bis 5. Dezember 2008 in Oestrich-Winkel Y1 - 2011 VL - 26 SP - 349 EP - 362 PB - Duncker und Humblot CY - Berlin ER - TY - CHAP A1 - Kempter, Guido A1 - Ritter, Walter ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Ergonomie von Handhelds T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 117 EP - 127 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Kriz, Willy Christian A1 - Auchter, Eberhard A1 - Wittenzeller, Helmut ED - Beran, Martin T1 - Summative evaluation of the nationwide german „Start-up-game” competition for entrepreneurship education T2 - Changing the world through meaningful play. Isaga 2010. Spokane, Washington, USA, July 5-9, 2010. Abstracts and Papers Y1 - 2011 SP - 98 EP - 102 PB - Eastern Washington Univ. Press CY - Spokane ER - TY - CHAP A1 - Mayer, Horst O. A1 - Pfister, Michael ED - Kempter, Guido ED - Mayer, Horst O. ED - Weidmann, Karl-Heinz T1 - Product Color T2 - design2product. Beiträge zur empirischen Designforschung Y1 - 2011 SP - 77 EP - 94 PB - Bucher CY - Hohenems u.a. ER - TY - CHAP A1 - Auchter, Eberhard A1 - Kriz, Willy Christian ED - Maritz, Alex T1 - Gender aspects by using start-up simulations for entrepreneurship education: results of theory-based evaluation studies T2 - Proceedings of the 8th AGSE International Entrepreneurship Research Exchange, Swinburne University of Technology, Melbourne, Australia, 1-4 February, 2011. KW - RESEARCH KW - publications KW - Swinburne Y1 - 2011 SP - 369 EP - 379 PB - Swinburne Univ. of Technology CY - Melbourne ER - TY - BOOK ED - Ilg, Markus ED - Rheinberger, Klaus T1 - Value Day 2011. Aktuelle Entwicklungen in Controlling & Finance KW - +WAA 300 KW - +WBH 725 KW - Controlling : Allgemeines KW - Finanzwirtschaft Y1 - 2011 SN - 978-3-86573-584-3 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - BOOK ED - Kriz, Willy Christian T1 - Planspiele für die Personalentwicklung T3 - Wandel und Kontinuität in Organisationen, 12 KW - +AWD 520 OuW KW - +SEC 572 KW - +WBB 570 KW - Fachhochschule Vorarlberg : Wandel und Kontinuität in Organisationen KW - Personalentwicklung KW - Planspiel, Rollenspiel Y1 - 2011 SN - 978-3-86573-648-2 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - BOOK ED - Horn, Sierk A. T1 - Emerging perspectives in Japanese human resource management Y1 - 2011 SN - 978-3-631-62098-4 PB - Peter Lang CY - Frankfurt M. ER - TY - BOOK ED - Feuerstein, Gerhild ED - Ritter, Walter T1 - Intelligent Wohnen. Zusammenfassung der Beiträge zum Usability Day IX. 20. Mai 2011 Y1 - 2011 PB - Pabst Science Publ. CY - Lengerich u.a. ER - TY - JOUR A1 - Mochalski, Paweł A1 - King, Julian A1 - Kupferthaler, Alexander A1 - Unterkofler, Karl A1 - Hinterhuber, Hartmann A1 - Amann, Anton T1 - Measurement of isoprene solubility in water, human blood and plasma by multiple headspace extraction gas chromatography coupled with solid phase microextraction JF - Journal of Breath Research Y1 - 2011 U6 - http://dx.doi.org/10.1088/1752-7155/5/4/046010 SN - 1752-7163 VL - 5. Jg. IS - H. 4 ER - TY - CHAP A1 - Masser, Philip A1 - Schumacher, Jens T1 - Role of Semantics for Supply Chain Interoperability. [Poster] T2 - 8th ITS European Congress. Intelligent mobility - ITS for sustainable transport of persons and goods in urban regions, Lyon, June 6 -9 Y1 - 2011 ER - TY - CHAP A1 - Fredersdorf, Frederic A1 - Feuerstein, Gerhild ED - Feuerstein, Gerhild ED - Fredersdorf, Frederic T1 - Wohnen im Alter - Bevölkerungsumfrage 2010 in der Marktgemeinde Götzis T2 - Intelligent Wohnen. Zusammenfassung der Beiträge zum Usability Day IX. 20. Mai 2011 Y1 - 2011 SP - 53 EP - 60 PB - Pabst Science Publ. CY - Lengerich u.a. ER - TY - CHAP A1 - Koc-Rauchenwald, Helin A1 - Unterkofler, Karl A1 - Teschl, Susanne A1 - King, Julian T1 - Mathematical modeling for breath gas analysis T2 - 5. Forschungsforum der österreichischen Fachhochschulen. 27.-28. April 2011, FH Campus Wien. Tagungsband Y1 - 2011 SP - 48 EP - 49 PB - FH Campus Wien CY - Wien ER - TY - JOUR A1 - Breuer, Thomas A1 - Jandacka, Martin A1 - Puhr, Rainer A1 - Rheinberger, Klaus A1 - Seeger, Markus T1 - The interaction dynamics between market and credit risk JF - International Review of Applied Financial Issues and Economics Y1 - 2011 VL - 3. Jg. IS - H. 3 SP - 681 EP - 690 ER - TY - JOUR A1 - Koc, Helin A1 - King, Julian A1 - Teschl, Gerald A1 - Unterkofler, Karl A1 - Teschl, Susanne A1 - Mochalski, Pawel A1 - Hinterhuber, Hartmann A1 - Amann, Anton T1 - The role of mathematical modeling in VOC analysis using isoprene as a prototypic example JF - Journal of Breath Research Y1 - 2011 U6 - http://dx.doi.org/10.1088/1752-7155/5/3/037102 SN - 1752-7163 VL - 5. Jg. IS - H. 3 ER - TY - CHAP A1 - King, Julian A1 - Unterkofler, Karl A1 - Teschl, Susanne A1 - Amann, Anton A1 - Teschl, Gerald T1 - Breath gas analysis for estimating physiological processes using anesthetic monitoring as a prototypic example T2 - 33rd annual international conference of the IEEE Engineering in Medicine and Biology Society (EMBC'11). Boston, MA, USA on August 30 - September 3, 2011 KW - Mathematical model KW - Anesthesia KW - Biomedical monitoring KW - Blood KW - Brain modeling KW - Breath Tests KW - Cardiac Output KW - Computer Simulation KW - Data models KW - Humans KW - Models, Biological KW - Monitoring KW - Pilot Projects Y1 - 2011 U6 - http://dx.doi.org/10.1109/IEMBS.2011.6090232 SP - 1001 EP - 1004 PB - Institute of Electrical and Electronics Engineers CY - Piscataway, NJ ER - TY - JOUR A1 - Jandačka, Martin A1 - Puhr, Rainer A1 - Seeger, Markus T1 - Wechselwirkungen zwischen Markt- und Kreditrisiko. Eine dynamische Analyse JF - Der Schweizer Treuhänder Y1 - 2011 VL - 85. Jg. IS - H. 11 SP - 953 EP - 958 ER - TY - CHAP A1 - Puhr, Rainer ED - Ilg, Markus ED - Rheinberger, Klaus T1 - Integriertes Markt- und Kreditrisikomodell für Firmenkunden T2 - Value Day 2011. Aktuelle Entwicklungen in Controlling & Finance Y1 - 2011 SP - 131 EP - 140 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - JOUR A1 - Alton-Scheidl, Roland T1 - net culture labs als Innovationsdrehscheiben JF - Ideenmanagement. Zeitschrift für Vorschlagwesen und Verbesserungsprozesse Y1 - 2011 UR - https://www.registeredcommons.org/view/167/0/9352 VL - 37. Jg. IS - H. 1 SP - 21 EP - 23 ER - TY - JOUR A1 - Chovan, Jozef A1 - Uherek, Frantisek A1 - Kurinec, Radoslav A1 - Satka, Alexander A1 - Pavlov, Jozef A1 - Seyringer, Dana T1 - Temperature characterization of passive optical components for WDM-PON FTTx JF - Advances in Electrical and Electronic Engineering. Optics and Optoelectronics KW - insertion loss KW - FTTx KW - polarization dependent loss. KW - Spectral multiplex KW - temperature sensitivity of parameters KW - WDM-PON system Y1 - 2011 U6 - http://dx.doi.org/10.15598/aeee.v9i3.512 SN - 1804-3119 VL - 9. Jg. IS - H. 3 SP - 143 EP - 149 ER - TY - JOUR A1 - Wetzstein, Irmgard T1 - Karrieresprungbrett Krisenherd JF - VOCER — Medien.Kritik.Debatte. Y1 - 2011 UR - http://vocer.org/de/artikel/do/detail/id/70/karrieresprungbrett-krisenherd.html ER - TY - CHAP A1 - Schumacher, Jens A1 - Rieder, Mathias A1 - Gschweidl, Manfred A1 - Masser, Philip ED - Uckelmann, Dieter ED - Harrison, Mark ED - Michahelles, Florian T1 - Intelligent cargo – using Internet of Things concepts to provide high interoperability for logistics systems T2 - Architecting the Internet of Things KW - Computational Intelligence KW - e-Commerce/e-business KW - Engineering Economics, Organization, Logistics, Marketing KW - Information Systems and Communication Service KW - Production/Logistics/Supply Chain Management Y1 - 2011 SN - 978-3-642-19156-5 SN - 978-3-642-19157-2 U6 - http://dx.doi.org/10.1007/978-3-642-19157-2_12 SP - 317 EP - 347 PB - Springer CY - Berlin u.a. ER - TY - CHAP A1 - Schumacher, Jens A1 - Gschweidl, Manfred A1 - Rieder, Mathias ED - Kreowski, Hans-Jörg ED - Scholz-Reiter, Bernd ED - Thoben, Klaus-Dieter T1 - EURIDICE: platform architecture in logistics for “The Internet of Things” T2 - Dynamics in Logistics. Second International Conference, LDIC 2009, Bremen, Germany, August 2009. Proceedings KW - Engineering Economics, Organization, Logistics, Marketing KW - Production/Logistics Y1 - 2011 SN - 978-3-642-11995-8 SN - 978-3-642-11996-5 U6 - http://dx.doi.org/10.1007/978-3-642-11996-5_21 SP - 235 EP - 244 PB - Springer CY - Berlin u.a. ER - TY - CHAP A1 - Horn, Sierk A1 - Beauducel, Andre A1 - Liepmann, Detlev ED - Horn, Sierk A. T1 - Faceted intelligence concept in Japan T2 - Emerging perspectives in japanese human resource management Y1 - 2011 SN - 978-3-631-62098-4 SP - 73 EP - 100 PB - Peter Lang CY - Frankfurt M. ER - TY - CHAP A1 - Horn, Sierk A1 - Liepmann, Detlev A1 - Beauducel, Andre ED - Horn, Sierk A. T1 - Applied perspectives on recruiting and work assessment in Japan T2 - Emerging perspectives in Japanese human resource management Y1 - 2011 SN - 978-631-62098-4-2011 SP - 101 EP - 128 PB - Peter Lang CY - Frankfurt am Main ER - TY - CHAP A1 - Kriz, Willy Christian ED - Mayer, Horst O. ED - Kriz, Willy Christian T1 - Evaluation von ePlanspielen und digitalen Lernspielen T2 - Evaluation von eLernprozessen. Theorie und Praxis Y1 - 2010 SP - 61 EP - 96 PB - Oldenbourg CY - München ER - TY - CHAP A1 - Matay, Ladislav A1 - Andok, Robert A1 - Barák, V. A1 - Ritomský, A. A1 - Konečnikova, I. A1 - Kostič, Ivan A1 - Partel, Stefan A1 - Hudek, Peter ED - Breza, Juraj T1 - Material optimization of the alignment marks for the EBDW lithography T2 - 8th International Conference on Advanced Semiconductor Devices Microsystems (ASDAM), 2010. 25 - 27 Oct. 2010, Smolenice Castle, Slovakia KW - alignment marks KW - deep reactive ion etching KW - e-beam lithography KW - EBDW lithography KW - electron beam lithography KW - electron-beam direct-write KW - Gold KW - Lithography KW - material optimization KW - Nickel KW - optimisation KW - photolithography KW - Resists KW - Silicon KW - sputter etching KW - Surfaces Y1 - 2010 U6 - http://dx.doi.org/10.1109/ASDAM.2010.5666341 SP - 85 EP - 88 PB - IEEE Operations Center CY - Piscataway, NJ ER - TY - CHAP A1 - Seyringer, Dana T1 - Low loss and high uniformity multimode interference splitter operating in a wide wavelength band. [Poster] T2 - ICOCON 2010 - The 9th International Conference on Optical Communications and Networks, October 24-27, 2010, Nanjing, China Y1 - 2010 ER - TY - CHAP A1 - Choleva, Pavlina A1 - Partel, Stefan A1 - Mathies, Roman T1 - Mikrogalvanik in dicken SU8 Strukturen T2 - 4. Forschungsforum der österreichischen Fachhochschulen. 7. - 8. April 2010. Tagungsband Y1 - 2010 SP - 304 EP - 308 PB - Fachhochschulstudiengänge Burgenland GesmbH CY - Eisenstadt ER - TY - CHAP A1 - Geser-Engleitner, Erika ED - Fredersdorf, Frederic ED - Himmer, Michael T1 - Eine sozialarbeiterische Diplomarbeit verfassen T2 - Junge Sozialarbeitswissenschaft. Diplomarbeiten zu relevanten Handlungsfeldern der Sozialen Arbeit Y1 - 2010 SP - 23 EP - 32 PB - VS Verl. für Sozialwissenschaften CY - Wiesbaden ER - TY - CHAP A1 - Alton-Scheidl, Roland T1 - net culture labs als Drehscheibe der Kreativen Klasse T2 - 4. Forschungsforum der österreichischen Fachhochschulen. 7. - 8. April 2010. Tagungsband Y1 - 2010 SP - 123 EP - 129 PB - Fachhochschulstudiengänge Burgenland GesmbH CY - Eisenstadt ER - TY - CHAP A1 - Roux, Pascale A1 - Fredersdorf, Frederic T1 - Unfallprävention bei Kleinkindern T2 - 4. Forschungsforum der österreichischen Fachhochschulen. 7. - 8. April 2010. Tagungsband Y1 - 2010 SP - 425 EP - 426 PB - Fachhochschulstudiengänge Burgenland GesmbH CY - Eisenstadt ER - TY - BOOK A1 - Fredersdorf, Frederic A1 - Heckmann, Wolfgang T1 - Der T-Faktor. Mäßigungskonzepte in der Sozialen Arbeit T3 - VS Research: Forschung und Entwicklung in der Sozial(arbeits)wissenschaft Y1 - 2010 PB - VS Verl. für Sozialwissenschaften CY - Wiesbaden ER - TY - JOUR A1 - Kriz, Willy Christian T1 - A systemic-constructivist approach to the facilitation and debriefing of simulations and games JF - Simulation & Gaming KW - debriefing KW - constructivism KW - examples of debriefing methods KW - facilitation KW - problem-oriented learning KW - systems theory Y1 - 2010 U6 - http://dx.doi.org/10.1177/1046878108319867 SN - 1046-8781 VL - 41. Jg. IS - H. 5 SP - 663 EP - 680 ER - TY - CHAP A1 - Mayer, Horst O. A1 - Walter, Wolfgang ED - Mayer, Horst O. ED - Walter, Wolfgang T1 - Kundenzufriedenheit mit einer Gemeindeverwaltung. Vom Herrschaftsverhältnis zum Dienstleistungsanspruch? T2 - Kundenzufriedenheit. Analyse und Management Y1 - 2010 SP - 46 EP - 68 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - JOUR A1 - Baumeister, Alexander A1 - Ilg, Markus T1 - Werttreiberorientierte Budgetierung in Banken JF - Controlling. Zeitschrift für erfolgsorientierte Unternehmenssteuerung Y1 - 2010 VL - 22. Jg. IS - H. 1 SP - 12 EP - 17 ER - TY - CHAP A1 - Breuer, Thomas A1 - Gorbach, Florian A1 - Maninger, Jörg A1 - Rheinberger, Klaus A1 - Seeger, Markus T1 - Entwicklung einer kostengünstigen und robusten Refinanzierungsstrategie zur optimalen Liquiditätssteuerung eines Kreditinstitutes T2 - 4. Forschungsforum der österreichischen Fachhochschulen. 7. - 8. April 2010. Tagungsband Y1 - 2010 SP - 166 EP - 171 PB - Fachhochschulstudiengänge Burgenland GesmbH CY - Eisenstadt ER - TY - CHAP A1 - Melkozerov, Alexander A1 - Beyer, Hans-Georg ED - Pelikan, Martin ED - Branke, Jürgen T1 - On the analysis of self-adaptive evolution strategies on elliptic model: first results T2 - GECCO 2010. Genetic and Evolutionary Computation Conference ; Wednesday - Sunday, July 7 - 11, 2010, Portland, Oregon KW - Evolution strategy KW - progress rate KW - self-adaptation KW - mutation strength KW - elliptic model Y1 - 2010 SN - 978-1-4503-0072-8 SP - 369 EP - 376 PB - ACM CY - New York, NY ER - TY - CHAP A1 - Alton-Scheidl, Roland ED - Parycek, Peter ED - Prosser, Alexander T1 - Unlocking government data with open licensing schemes T2 - EDem2010. Proceedings of the 4th International Converence on E-Democracy, 6-7 May 2010, Danube University Krems, Austria Y1 - 2010 SP - 311 EP - 317 PB - Österr. Comp.-Ges CY - Wien ER - TY - CHAP A1 - Dontschewa, Miglena A1 - Künz, Andreas A1 - Schäferle, Alexander A1 - Fischer, Maximilian A1 - Herbster, Mathias ED - Künz, Andreas ED - Dontschewa, Miglena T1 - Smart Room Visualisierung T2 - Eintauchen in Medienwelten. Zusammenfassung der Beiträge zum Usability Day VIII, 21 Mai 2010 Y1 - 2010 SP - 120 EP - 126 PB - Pabst Science Publ. CY - Lengerich u.a. ER - TY - BOOK ED - Künz, Andreas ED - Dontschewa, Miglena T1 - Eintauchen in Medienwelten. Zusammenfassung der Beiträge zum Usability Day VIII, 21. Mai 2010 KW - +INC 310 KW - +INC 320 KW - Benutzerschnittstelle KW - Mensch-Maschine-Kommunikation Y1 - 2010 SN - 978-3-89967-642-6 PB - Pabst Science Publ. CY - Lengerich u.a. ER - TY - BOOK ED - Fredersdorf, Frederic ED - Himmer, Michael T1 - Junge Sozialarbeitswissenschaft. Diplomarbeiten zu relevanten Handlungsfeldern der Sozialen Arbeit T3 - VS Research: Forschung und Entwicklung in der Sozial(arbeits)wissenschaft KW - +AWD 750 KW - +SSD 053 KW - +SSD 250 KW - Fachhochschule Vorarlberg : Diplomarbeit : Sozialarbeit KW - Sozialarbeit : Arbeitsfeld KW - Sozialarbeit : Didaktik, Studium Y1 - 2010 SN - 978-3-531-17371-9 PB - VS Verl. für Sozialwissenschaften CY - Wiesbaden ER - TY - CHAP A1 - Himmer, Michael A1 - Fredersdorf, Frederic ED - Fredersdorf, Frederic ED - Himmer, Michael T1 - Zur Entwicklung sozialarbeiterischer Studiengänge in Österreich und Vorarlberg T2 - Junge Sozialarbeitswissenschaft. Diplomarbeiten zu relevanten Handlungsfeldern der Sozialen Arbeit Y1 - 2010 SP - 15 EP - 22 PB - VS Verl. für Sozialwissenschaften CY - Wiesbaden ER - TY - CHAP A1 - Mayer, Horst O. ED - Mayer, Horst O. ED - Kriz, Willy Christian T1 - Evaluation von eLearning-Produkten/Prozessen T2 - Evaluation von eLernprozessen. Theorie und Praxis Y1 - 2010 SP - 15 EP - 24 PB - Oldenbourg CY - München ER - TY - CHAP A1 - Schöch, Heidrun A1 - Walter, Wolfgang ED - Mayer, Horst O. ED - Walter, Wolfgang T1 - Grenzüberschreitende Kundenbindung im Einzelhandel am Beispiel eines Einkaufszentrums T2 - Kundenzufriedenheit. Analyse und Management Y1 - 2010 SP - 21 EP - 46 PB - Wiss. Verl. Berlin CY - Berlin ER - TY - CHAP A1 - Kempter, Guido ED - Mayer, Horst O. ED - Kriz, Willy Christian T1 - Evaluation von Bedienoberflächen für eLearning Applikationen T2 - Evaluation von eLernprozessen. Theorie und Praxis Y1 - 2010 SP - 201 EP - 209 PB - Oldenbourg CY - München ER - TY - JOUR A1 - Ritter, Walter T1 - Benefits of subliminal feedback loops in human-computer interaction JF - Advances in Human-Computer Interaction Y1 - 2010 U6 - http://dx.doi.org/10.1155/2011/346492 SN - 1687-5893 VL - 4. Jg. ER - TY - BOOK A1 - Saam, Nicole J. A1 - Kriz, Willy Christian T1 - Partizipation in Großgruppen. Bd. 1: Soziologische Perspektiven T3 - Organisation und Beratung, 2 KW - +SPC 660 KW - Gruppe : Sozialpsychologie Y1 - 2010 PB - Lit CY - Münster u.a. ER -