Refine
Document Type
- Conference Proceeding (12)
- Article (4)
- Book (1)
Institute
- Forschungszentrum Digital Factory Vorarlberg (17) (remove)
Keywords
- photonics (3)
- Cloud manufacturing (2)
- Ontologies (2)
- 2x2 optical switch (1)
- 3D 1×4 Multimode Interference Splitter (1)
- 3D MMI splitter (1)
- 3D Y-branch splitter (1)
- AWG (1)
- Articifial intelligence (1)
- Auction-based production planning (1)
In this paper, the design of three-dimensional configuration of Y-branch splitter is compared with Multimode Interference splitter. Both splitters use the IP-Dip polymer as a standard material for 3D laser lithography. The optical properties of the splitters for both approaches are discussed and compared.
In this work, we investigated the influence of different etch depths of the rib waveguides on the performance of SiN-based AWGs. For this purpose, an 8-channel 100 GHz AWG was designed for a center wavelength of 850 nm. The design parameters entered were calculated using the AWG-Parameters tool. The simulations were performed with a commercial photonic tool PHASAR from Optiwave. The simulated performance was evaluated using the AWG-Analyzer tool. For the AWG design, we used three identical rib waveguides with different etch depths to simulate possible etch imperfection. The simulations show the wavelength shift and degradation of the AWG performance.
We present 256-channel, 25-GHz AWG designed for ultra-dense wavelength division multiplexing. For the design two in-house developed tools were used: AWG-Parameters tool for the calculation of input design parameters and AWGAnalyser tool, used to evaluate the simulated transmission characteristics. The AWG structure was designed for AWG central wavelength of 1550 nm and simulated with PHASAR tool from Optiwave. To keep the size of AWG structure as small as possible the number of waveguides in the phased array was tested. The simulations show that there is a certain minimum number of phased array waveguides necessary to reach sufficient AWG performance. After optimization, the AWG structure reached 10 cm x 11 cm in size and satisfying optical properties.
This paper describes two different designs of 1×8 passive optical splitters. The first splitter consists of cascade arranged directional waveguide branches (Y-branch splitter) with (0.8×0.16) µm2 waveguide cross-section. The second splitter is based on multimode interference occurring in a large MMI coupler, which uses a self-imaging effect for beam propagation, exhibiting the same waveguide core size as a Y-branch splitter. The waveguide channel profile, used in both approaches, is based on a silicon nitride material platform, with a refractive index of core being nc = 1.925 and a refractive index of cladding ncl = 1.4575. The splitters are designed as a planar structure for a medical operating wavelength 850 nm. Design, simulation, and optimization of passive optical components are performed by a commercial photonic software tool BeamPROP simulation engine by RSoft Photonics Suite tool, employing beam propagation method. This work aims to find the minimum physical dimensions of the designed splitters with the satisfactory optical performance. According to the minimum insertion loss and minimum non-uniformity, the optimum length of the splitters is determined. Finally, the optical properties of splitters for both approaches are discussed and compared with each other.
ROS 2 in Embedded Systemen
(2022)
Das Robot Operating System in seiner zweiten Version (ROS 2) findet zunehmend Verwendung und das nicht nur in Robotern. Dieser Beitrag gibt einen Überblick über den Aufbau und die Funktion von ROS 2. Die wesentlichen Elemente werden vorgestellt, das Publish-Subscribe-Konzept, das der Kommunikation zugrunde liegt, wird erläutert. Die Anforderungen von ROS 2 an Hardware und Betriebssystem werden beleuchtet und es werden Betrachtungen zu dessen Echtzeitverhalten gemacht.
The paper deals with the optimization of 2x2 optical switch for photonic integrated circuits based on two 2x2 MMI splitters and two phase-modulators. The optical switch was modelled in the RSoftCAD with the simulation tool BeamPROP. The optimization was done to minimise the insertion losses and broaden the spectral band at 1550 nm by using linear tapers in a 2x2 MMI splitter topology. The 2x2 optical switch is a common element for creating more complex 1xN or NxN optical switches in all-optical signal processing.
Design, simulation, and optimization of the 1×4 optical three-dimensional multimode interference splitter using IP-Dip polymer as a core and polydimethylsiloxane (PDMS) Sylgard 184 as a cladding is demonstrated. The splitter was simulated by using beam propagation method in BeamPROP simulation module of RSoft photonic tool and optimized for an operating wavelength of 1.55 μm . According to the minimum insertion loss, the dimensions of the splitter were optimized for a waveguide with a core size of 4×4 μm2 . The objective of the study is to create the design for fabrication by three-dimensional direct laser writing optical lithography.
This paper aims to study the design, simulation, and optimization of low-loss Y-branch passive optical splitters up to 64 output ports for telecommunication applications. For a waveguide channel profile, the standard material silica-on-silicon is used. The Y-splitters are designed and simulated at telecommunication operating wavelength, λ = 1550 nm. Except for the lengths of the used Y-branches, and a core size of the waveguides, design parameters such as port pitch between the waveguides and simulation parameters for all splitters are considered fixed. The simulation results are analyzed to determine the optimum length of the splitters and the optimum core size. Based on this optimization the total length of the highest designed 1×64 Y-branch splitter was reduced by 41.14 % for a waveguide core (5×5) μm2 compared to the length of splitter with a standard (6×6) μm2 core size.
A trend from centralized to decentralized production is emerging in the manufacturing domain leading to new and innovative approaches for long-established production methods. A technology supporting this trend is Cloud Manufacturing, which adapts technologies and concepts known from cloud computing to the manufacturing domain. A core aspect of Cloud Manufacturing is representing knowledge about manufacturing, e.g., machine capabilities, in a suitable form. This knowledge representation should be flexible and adaptable so that it fits across various manufacturing domains, but, at the same time, should also be specific and exhaustive. We identify three core capabilities that such a platform has to support, i.e., the product, the process and the production.We propose representing this knowledge in semantically specified knowledge graphs, essentially creating three through features interconnected ontologies each representing a facet of manufacturing. Finally, we present an exemplary implementation of a Cloud Manufacturing platform using this representation and its advantages.