Refine
Year of publication
Document Type
- Article (70) (remove)
Institute
- Forschungszentrum Mikrotechnik (24)
- Forschungszentrum Energie (14)
- Forschungszentrum Business Informatics (11)
- Soziales & Gesundheit (10)
- Department of Computer Science (Ende 2021 aufgelöst; Integration in die übergeordnete OE Technik) (8)
- Technik | Engineering & Technology (8)
- Forschungszentrum Human Centred Technologies (5)
- Wirtschaft (3)
- Forschungszentrum Digital Factory Vorarlberg (1)
- Gestaltung (1)
Has Fulltext
- yes (70) (remove)
Keywords
- Peripheral arterial disease (3)
- Y-branch splitter (3)
- Bubble column humidifier (2)
- Demand response (2)
- Demand side management (2)
- Desalination (2)
- Distribution grids (2)
- Energy storage (2)
- Humidification-dehumidification (2)
- Power tracking (2)
We have demonstrated micromachining of bulk 3C silicon carbide (3C- SiC) wafers by employing 1028nm wavelength femtosecond laser pulses of energy less than 10 nJ directly from a femtosecond laser oscillator, thus eliminating the need for an amplified system and increasing the micromachining speed by more than four orders of magnitude.
We have investigated the ablation behaviour of single crystal SrTiO3 <100> with focus on the influence of the pulse duration at a wavelength of 248 nm. The experiments were performed with KrF-excimer lasers with pulse durations of 34 ns and 500 fs, respectively. Femtosecond-ablation turns out to be more efficient by one order of magnitude and to eliminate the known problem of cracking of SrTiO3 during laser machining with longer pulses. In addition, the cavities ablated with femtosecond pulses display a smoother surface with no indication of melting and well-defined, sharp edges. These effects can be explained by the reduced thermal shock effect on the material by using ultrashort pulses.
Modern portable electronic devices have seen component heat load increasing, while the space available for heat dissipation has decreased. This requires the thermal management system to be optimized to attain the high performance heat sink. Heat sinks plays a major role for dissipating heat in electronic devices. Phase change material (PCM) is used to enhance the heat dissipation in heat sink. This paper reports the results of an experimental investigation of the performance of Pin fin heat sinks filled with phase change materials for thermal management of electronic devices. The experimental set ups are prepared with the graphical programming language with Lab VIEW (Laboratory Virtual Instruments for Engineering Workbench. Three different types of Pin fin Heat sink with and without PCM are investigated based on different operational timings and the temperature is acquired with the help of Data Acquisition Card (DAQ). The results indicated that the inclusion of the PCM could stabilize the temperature for a longer period and reduce the heating rates and peak temperatures of heat sink with increasing the number of fins can enhance the thermal performance of electronic devices.
This paper presents a project developed at the K.S.Rangasamy College of Technology (Tamilnadu,India) aimed at designing, implementing, and testing an autonomous multipurpose vehicle with safe, efficient, and economic operation. This autonomous vehicle moves through the crop lines of a Agricultural land and performs tasks that are tedious and/or hazardous to the farmers. First, it has been equipped for spraying, but other configurations have also been designed, such as: a seeding ,plug platform to reach the top part of the plants to perform different tasks (pruning, harvesting, etc.), and a trailer to transport the fruits, plants, and crop waste.
The goal of this paper is to design a low-loss 1 x 32 Y-branch optical splitter for optical transmission systems, using two different design tools employing Beam Propagation Method. As a first step, a conventional 1 x 32 Y-branch splitter was designed and simulated in two-dimensional environment of OptiBPM photonic tool. The simulated optical properties feature high loss, high asymmetric splitting ratio and a large size of the designed structure, too. In the second step of this work we propose an optimization of the conventional splitter design leading to suppression of the asymmetric splitting ratio to one-third of its initial value and to the improvement of the losses by nearly 2 dB. In addition, 50% size reduction of the designed structure was also achieved. This length-optimized low-loss splitter was then modelled in a three-dimensional environment of RSoft photonic tool and the simulated results confirm the strong improvement of the optical properties.
Breath analysis offers a non-invasive and rapid diagnostic method for detecting various volatile organic compounds that could be indicators for different diseases, particularly metabolic disorders including type 2 diabetes mellitus. The development of type 2 diabetes mellitus is closely linked to metabolic dysfunction of adipose tissue and adipocytes. However, the VOC profile of human adipocytes has not yet been investigated. Gas chromatography with mass spectrometric detection and head-space needle trap extraction (two-bed Carbopack X/Carboxen 1000 needle traps) were applied to profile VOCs produced and metabolised by human Simpson Golabi Behmel Syndrome adipocytes. In total, sixteen compounds were identified to be related to the metabolism of the cells. Four sulphur compounds (carbon disulphide, dimethyl sulphide, ethyl methyl sulphide and dimethyl disulphide), three heterocyclic compounds (2-ethylfuran, 2-methyl-5-(methyl-thio)-furan, and 2-pentylfuran), two ketones (acetone and 2-pentanone), two hydrocarbons (isoprene and n-heptane) and one ester (ethyl acetate) were produced, and four aldehydes (2-methyl-propanal, butanal, pentanal and hexanal) were found to be consumed by the cells of interest. This study presents the first profile of VOCs formed by human adipocytes, which may reflect the activity of the adipose tissue enzymes and provide evidence of their active role in metabolic regulation. Our data also suggest that a previously reported increase of isoprene and sulphur compounds in diabetic patients may be explained by their production by adipocytes. Moreover, the unique features of this profile, including a high emission of dimethyl sulphide and the production of furan-containing VOCs, increase our knowledge about metabolism in adipose tissue and provide diagnostic potential for future applications.
Product ion distributions resulting from the primary reactions of H3O+ with nine D-labeled volatile organic compounds and the subsequent sequential reactions with H2O have been determined using a Proton Transfer Reaction Time of Flight Mass Spectrometer (PTR-TOF 8000 (IONICON Analytik GmbH)) at various reduced electric field (E/N) values ranging from 80 up to 150 Td and for two different absolute humidity levels of air sample < 0.1% and 5%. The specific D-labeled compounds used in this study are acetone-d6, toluene-d8, benzene-d6, ethanol-d (C2H5OD), ethanol-d2 (CH3CD2OH), ethanol-d6, 2-propanol-d8, 2-propanol-d3 (CD3CH(OH)CH3), and isoprene-d5 (CH2CHC(CD2)CD3). With the exception of the two 2-propanol compounds, non-dissociative proton transfer is the dominant primary reaction pathway. For 2-propanol-d8 and 2-propanol-d3 the major primary reaction channel involved is dissociative proton transfer. However, unlike their undeuterated counterparts, the primary product ions undergo subsequent deuterium/hydrogen isotope exchange reactions with the ever present water in the drift tube, the extent of which of course depends on the humidity within that tube. This exchange leads to the generation of various isotopologue product ions, the product ion branching percentages of which are also
dependent on the humidity in the drift tube. This results in complex mass spectra and the distribution of product ions leads to issues of reduced sensitivity and accuracy. However, the effect of D/H exchange considerably varies between the compounds under study. In the case of acetone-d6 it is very weak (<1%), because the exchange process is not facile when the deuterium is in the methyl functional group. In comparison, the H3O+/ benzene-d6 (C6D6) reaction and sequential reactions with water result in the production of the isotopologue ions C6Dn(H7-n)+ (where n = 0–6). Changing the value of E/N and/or the humidity in the drift tube considerably affects the amount of the isotope exchange reactions and hence the resulting sequential product ion distributions. An important conclusion of the findings from this work is that care must be taken in the choice of an exogenous deuterated compound for use in breath pharmacokinetic studies using proton transfer reaction mass spectrometry; otherwise the resulting D/H exchange processes impose interpretative problems.
© 2018 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY license
(http://creativecommons.org/licenses/by/4.0/).
Transparent laser-structured glasses with superhydrophilic properties for anti-fogging applications
(2019)
Ultrashort pulse laser structuring enables direct modification of glass surfaces to generate superhydrophilic properties for anti-fogging applications. This approach makes coatings dispensable and the generated surfaces remain thermally, mechanically, and chemically resistant. However, the laser-generated structures usually cause scattering, which decreases transmission and may disturb the vision through the modified glass in the dry state. The aim of this study was to find a laser-processing strategy to achieve superhydrophilic, anti-fogging properties on glass surfaces with maximum transmission and minimal visual perception of the generated structure. For this purpose, we used an ultrashort-pulsed laser to generate periodic patterns of rippled circles or rough holes with varying pitch. The water contact angle and transmission of the structured glasses were measured as a function of the structured area. It was found that a periodic pattern of holes, which covers less than 1% of the surface, is already sufficient to reach the superhydrophilic state (contact angle < 5°) and provides nearly the same transmission as pristine glass. Pictures of objects imaged through dry, structured glasses, which were placed close to the lens or object, showed in both cases only a minimal decrease of contrast. If this minor drawback can be accepted, this direct laser structuring approach could be an interesting alternative to coating-based techniques and leaves even room to apply additional coatings for the fabrication of multi-functional special glasses.
In engineering design, optimization methods are frequently used to improve the initial design of a product. However, the selection of an appropriate method is challenging since many
methods exist, especially for the case of simulation-based optimization. This paper proposes a systematic procedure to support this selection process. Building upon quality function deployment, end-user and design use case requirements can be systematically taken into account via a decision
matrix. The design and construction of the decision matrix are explained in detail. The proposed
procedure is validated by two engineering optimization problems arising within the design of box-type boom cranes. For each problem, the problem statement and the respectively applied optimization methods are explained in detail. The results obtained by optimization validate the use
of optimization approaches within the design process. The application of the decision matrix shows the successful incorporation of customer requirements to the algorithm selection.
Zusammenfassung: Eine umfassende Literaturrecherche (Comprehensive Literature Search, CLS) bezeichnet eine umfangreiche und aufwändige Recherche mit dem Ziel, möglichst alle Studien zur Beantwortung einer zugrundeliegenden Forschungsfrage im Rahmen einer systematischen Übersichtsarbeit zu identifizieren. Konkrete Empfehlungen oder eine Definition des Begriffs CLS gibt es jedoch nicht. Der vorliegende Beitrag führt in eine Rahmung der CLS ein, stellt die damit einhergehenden Herausforderungen dar und weist auf methodische Implikationen sowie mögliche zukünftige Forschungsbereiche hin.
Adult muscle carnitine palmitoyltransferase (CPT) II deficiency is a rare autosomal recessive disorder of long-chain fatty acid metabolism. It is typically associated with recurrent episodes of exercise-induced rhabdomyolysis and myoglobinuria, in most cases caused by a c.338C > T mutation in the CPT2 gene. Here we present the pedigree of one of the largest family studies of CPT II deficiency caused by the c.338C > T mutation, documented so far. The pedigree comprises 24 blood relatives
of the index patient, a 32 year old female with genetically proven CPT II deficiency. In total, the mutation was detected in 20 family members, among them five homozygotes and 15 heterozygotes. Among all homozygotes, first symptoms of CPT II deficiency occurred during childhood. Additionally, two already deceased relatives of the index patient were carriers of at least one copy of the genetic variant, revealing a remarkably high prevalence of the c.338C > T mutation within the tested family. Beside the index patient, only one individual had been diagnosed with CPT II deficiency prior to this study and three cases of CPT II deficiency were newly detected by this family study, pointing
to a general underdiagnosis of the disease. Therefore, this study emphasizes the need to raise awareness of CPT II deficiency for correct diagnosis and accurate management of the disease.
Breath analysis holds great promise for real-time and non-invasive medical diagnosis. Thus, there is a considerable need for simple-in-use and portable analyzers for rapid detection of breath indicators for different diseases in their early stages. Sensor technology meets all of these demands. However, miniaturized breath analyzers require adequate breath sampling methods. In this context, we propose non-contact sampling; namely the collection of breath samples by exhalation from a distance into a miniaturized collector without bringing the mouth into direct contact with the analyzing device. To evaluate this approach different breathing maneuvers have been tested in a real-time regime on a cohort of 23 volunteers using proton transfer reaction mass spectrometry. The breathing maneuvers embraced distinct depths of respiration, exhalation manners, size of the mouth opening and different sampling distances. Two inhalation modes (normal, relaxed breathing and deep breathing) and two exhalation manners (via smaller and wider lips opening) forming four sampling scenarios were selected. A sampling distance of approximately 2 cm was found to be a reasonable trade-off between sample dilution and requirement of no physical contact of the subject with the analyzer. All four scenarios exhibited comparable measurement reproducibility spread of around 10%. For normal, relaxed inspiration both dead-space and end-tidal phases of exhalation lasted approximately 1.5 s for both expiration protocols. Deep inhalation prolongs the end-tidal phase to about 3 s in the case of blowing via a small lips opening, and by 50% when the air is exhaled via a wide one. In conclusion, non-contact breath sampling can be considered as a promising alternative to the existing breath sampling methods, being relatively close to natural spontaneous breathing.
Background: Peripheral arterial disease (PAD) is a common and severe disease with a highly increased cardiovascular morbidity and mortality. Through the circulatory disorder and the linked undersupply of oxygen carriers in the lower limbs, the ongoing decrease of the pain-free walking distance occurs with a significant reduction in patients’ quality of life. Studies including activity monitoring for patients with PAD are rare and digital support to increase activity via mobile health technologies is mainly targeted at patients with cardiovascular disease in general. The special requirement of patients with PAD is the need to reach a certain pain level to improve the pain-free walking distance. Unfortunately, both poor adherence and availability of institutional resources are major problems in patient-centered care.
Objective: The objective of this trackPAD pilot study is to evaluate the feasibility of a mobile phone–based self tracking app to promote physical activity and supervised exercise therapy (SET) in particular. We also aim for a subsequent patient centered adjustment of the app prototype based on the results of the app evaluation and process evaluation.
Methods: This study was designed as a closed user group trial, with assessors blinded, and parallel group study with face-to-face components for assessment with a follow-up of 3 months. Patients with symptomatic PAD (Fontaine stage IIa or IIb) and possession of a mobile phone were eligible. Eligible participants were randomly assigned into study and control group, stratified by their distance covered in the 6-min walk test, using the software TENALEA. Participants randomized to the study group received usual care and the mobile intervention (trackPAD) for the follow-up period of 3 months, whereas participants randomized to the control group received only usual care. TrackPAD records the frequency and duration of training sessions and pain level using manual user input. Clinical outcome data were collected at the baseline and after 3 months via validated tools (6-min walk test, ankle-brachial index, and duplex ultrasound at the lower arteries) and self-reported quality of life. Usability and quality of the app was determined using the user version of the Mobile Application Rating Scale.
Results: The study enrolled 45 participants with symptomatic PAD (44% male). Of these participants, 21 (47%) were randomized to the study group and 24 (53%) were randomized to the control group. The distance walked in the 6-min walk test was comparable in both groups at baseline (study group: mean 368.1m [SD 77.6] vs control group: mean 394.6m [SD 100.6]).
Conclusions: This is the first trial to test a mobile intervention called trackPAD that was designed especially for patients with PAD. Its results will provide important insights in terms of feasibility, effectiveness, and patient preferences of an app-based mobile intervention supporting SET for the conservative treatment of PAD.
The humidification-dehumidification process (HDH) for desalination is a promising technology to address water scarcity issues in rural regions. However, a low humidifier efficiency is a weakness of the process. Bubble column humidifiers (BCH) are promising for HDH, as they provide enhanced heat and mass transfer and have low maintenance requirements. Previous studies of HDH-systems with BCHs draw different conclusions regarding the impact of superficial air velocity and liquid height on the humidification. Furthermore, the impact of flow characteristics has never been investigated systematically at all. In this study, an optimized BCH test setup that allows for optical analysis of the humidifier is used and evaluated. Our test setup is validated, since the influence of water temperature on the humidification, which is exponential, is reproduced. Measurements with seawater show that the normalised system productivity is increased by about 56 % with an increase in superficial air velocity from 0.5 to 5 cm/s. Furthermore, the system productivity is increased by around 29 % with an increase in liquid height from 60 to 378 mm. While the impact of superficial air velocity can be traced back to temperature changes at the humidifier and dehumidifier outlets, the impact of liquid height is shown to be caused by a smaller heat loss surface in the humidifier with an increase in liquid height. For the impact of sieve plate orifice diameter, a clear influence on the humidification is not apparent, this parameter needs to be investigated further. Finally, our new test setup allows for analysing the humidification of air (1) in a systematic way, (2) in relevant measurement ranges and (3) in comparison with optical analyses of the flow characteristics.
Greater specific energy densities in lithium-ion batteries can be achieved by using three-dimensional (3D) porous current collectors, which allow for greater areal mass loadings of the electroactive material. In this paper, we present the use of embroidered current collectors for the preparation of thick, pouch-type Li-ion batteries. Experiments were performed on LiFePO 4 (LFP) water-based slurries using styrene-butadiene rubber (SBR) as binder and sodium carboxymethyl cellulose (CMC) as thickener, and formulations of different rheological characteristics were investigated. The electrochemical performance (cyclic voltammetry, rate capability) and morphological characteristics of the LFP half-pouch cells (X-ray micro computed tomography and scanning electron microscopy) were compared between the formulations. An optimum electrode formulation was identified, and a mechanism is proposed to explain differences between the formulations. With the optimum electrode formulation, 350 µm casted electrodes with high mechanical stability were achieved. Electrodes exhibited 4–6 times greater areal mass loadings (4–6 mAh cm −2 ) and 50% greater electroactive material weight than with foils. In tests of half- and full-pouch embroidered cells, a 50% capacity utilization at 1C-rate and 11% at 2C-rate were observed, with a full recovery at C/5-rate. The cycling stability was also maintained over 55 cycles.
Gas hydrates are usually synthesized by bringing together a pressurized gas and liquid or solid water. In both cases, the transport of gas or water to the hydrate growth site is hindered once an initial film of hydrate has grown at the water–gas interface. A seemingly forgotten gas-phase technique overcomes this problem by slowly depositing water vapor on a cold surface in the presence of the pressurized guest gas. Despite being used for the synthesis of low-formation-pressure hydrates, it has not yet been tested for hydrates of CO 2 and CH 4 . Moreover, the potential of the technique for the study of hydrate decomposition has not been recognized yet. We employ two advanced implementations of the condensation technique to form hydrates of CO 2 and CH 4 and demonstrate the applicability of the process for the study of hydrate decomposition and the phenomenon of self-preservation. Our results show that CO 2 and CH 4 hydrate samples deposited on graphite at 261–265 K are almost pure hydrates with an ice fraction of less than 8%. Rapid depressurization experiments with thin deposits (approx. 330 mm thickness) of CO 2 hydrate on an aluminum surface at 265 K yield identical dissociation curves when the deposition is done at identical pressure. However, hydrates deposited at 1 MPa almost completely withstand decomposition after rapid depressurization to 0.1 MPa, while samples deposited at 2 MPa decompose 7 times faster. Therefore, this synthesis technique is not only applicable for the study of hydrate decomposition but can also be used for the controlled deposition of a super-preserved hydrate.
Investigation of non-uniformly emitting optical fiber diffusers on the light distribution in tissue
(2020)
The Digital Factory Vorarlberg is the youngest Research Center of Vorarlberg University of Applied Sciences. In the lab of the research center a research and learning factory has been established for educating students and employees of industrial partners. Showcases and best practice scenarios for various topics of digitalization in the manufacturing industry are demonstrated. In addition, novel methods and technologies for digital production, cloud-based manufacturing, data analytics, IT- and OT-security or digital twins are being developed. The factory comprises only a minimum core of logistics and fabrication processes to guarantee manageability within an academic setup. As a product, fidget spinners are being fabricated. A webshop allows customers to individually design their products and directly place orders in the factory. A centralized SCADA-System is the core data hub for the factory. Various data analytic tools and methods and a novel database for IoT-applications are connected to the SCADA-System. As an alternative to on premise manufacturing, orders can be pushed into a cloud-based manufacturing platform, which has been developed at the Digital Factory. A broker system allows fabrication in distributed facilities and offers various optimization services. Concepts, such as outsourcing product configuration to customers or new types of engineering services in cloud-based manufacturing can be explored and demonstrated. In this paper, we present the basic concept of the Digital Factory Vorarlberg, as well as some of the newly developed topics.
Lead–magnesium niobate lead titanate (PMN-PT) has been proven as an excellent material for sensing and actuating applications. The fabrication of advanced ultra-small PMN-PT-based devices relies on the availability of sophisticated procedures for the micro-machining of PMN-PT thin films or bulk substrates. Approaches reported up to date include chemical etching, excimer laser ablation, and ion milling. To ensure an excellent device performance, a key mandatory feature for a micro-machining process is to preserve as far as possible the crystalline quality of the substrates; in other words, the fabrication method must induce a low density of cracks and other kind of defects. In this work, we demonstrate a relatively fast procedure for the fabrication of high-quality PMN-PT micro-machined actuators employing green femtosecond laser pulses. The fabricated devices feature the absence of extended cracks and well-defined edges with relatively low roughness, which is advantageous for the further integration of nanomaterials onto the piezoelectric actuators.