Refine
Year of publication
- 2020 (48) (remove)
Document Type
- Article (48) (remove)
Institute
- Wirtschaft (15)
- Soziales & Gesundheit (12)
- Forschungszentrum Mikrotechnik (9)
- Forschungszentrum Business Informatics (4)
- Technik | Engineering & Technology (4)
- Department of Computer Science (Ende 2021 aufgelöst; Integration in die übergeordnete OE Technik) (3)
- Forschungszentrum Energie (3)
- Department of Engineering (Ende 2021 aufgelöst; Integration in die übergeordnete OE Technik) (1)
- Forschung (1)
- Forschungszentrum Digital Factory Vorarlberg (1)
Keywords
- Ausscheidung (4)
- Agent-based simulation testing (1)
- Air humidification (1)
- Altenheim (1)
- Alter (1)
- Anaesthetics (1)
- Automated Adjustment (1)
- BWL (1)
- Bedeutungskonstruktion (1)
- Beobachter (1)
The humidification-dehumidification process (HDH) for desalination is a promising technology to address water scarcity issues in rural regions. However, a low humidifier efficiency is a weakness of the process. Bubble column humidifiers (BCH) are promising for HDH, as they provide enhanced heat and mass transfer and have low maintenance requirements. Previous studies of HDH-systems with BCHs draw different conclusions regarding the impact of superficial air velocity and liquid height on the humidification. Furthermore, the impact of flow characteristics has never been investigated systematically at all. In this study, an optimized BCH test setup that allows for optical analysis of the humidifier is used and evaluated. Our test setup is validated, since the influence of water temperature on the humidification, which is exponential, is reproduced. Measurements with seawater show that the normalised system productivity is increased by about 56 % with an increase in superficial air velocity from 0.5 to 5 cm/s. Furthermore, the system productivity is increased by around 29 % with an increase in liquid height from 60 to 378 mm. While the impact of superficial air velocity can be traced back to temperature changes at the humidifier and dehumidifier outlets, the impact of liquid height is shown to be caused by a smaller heat loss surface in the humidifier with an increase in liquid height. For the impact of sieve plate orifice diameter, a clear influence on the humidification is not apparent, this parameter needs to be investigated further. Finally, our new test setup allows for analysing the humidification of air (1) in a systematic way, (2) in relevant measurement ranges and (3) in comparison with optical analyses of the flow characteristics.
Quasilineare Tauchankerspule
(2020)
Shaolin Wu Fo Dao – die Synthese japanischer und chinesischer Kampfkunst-Lehre auf der Grundlage zen-buddhistischer Theorie und Praxis ist eine neu geschaffene Disziplin. In dieser Fusion verbinden sich wesentliche Elemente aus Budo und Shaolin (-Wudao), deren traditionellen Körper-Geist-Übungen von Kampftechnik (Bu/Wu) und Meditation (Zen/Chan) als originäre Weg- und Heilslehre (Do/Dao) seit jeher der Persönlichkeits- und spirituellen Entwicklung des Ausübenden dienten.
Hier nun, in der Überwindung alter Grenzen zwischen japanischer und chinesischer Kampfkunstsysteme („hart“ und „weich“), wurde hier nun erstmaligen ein zusammengewachsenes Kampfkunstsystem kreiert, um die beidseits positiven Wirkungen auf den Menschen zu bündeln und – und das ist das Besondere – sie in den Dienst buddhistischer (Butsu, jap.: Buddha / chin. Fo) Psychologie und Psychotherapie zu stellen.
Die Verbindung von Budo mit Shaolin als eigenständiges praktisches Lehrkonzept, allein schon eine „revolutionäre Innovation“, erfährt durch ihren Einsatz als spezielle Methode einer Heilkunst zusätzlich Pioniercharakter in der Behandlung von Leid. Gemeint sind sowohl Ansätze aus der Budopädagogik und speziellen Budotherapie zur Heilung, Linderung oder Prävention von physischen, psychosomatischen und psychischen Krisen, Störungen, Krankheiten, Behinderungen und Leiden, als auch im Sinne des philosophischen und wissenschaftlichen Buddhismus, „das Leid in der Welt zu mindern“, zum Wohle des Menschen, für sein Glück und Frieden zu arbeiten.
Greater specific energy densities in lithium-ion batteries can be achieved by using three-dimensional (3D) porous current collectors, which allow for greater areal mass loadings of the electroactive material. In this paper, we present the use of embroidered current collectors for the preparation of thick, pouch-type Li-ion batteries. Experiments were performed on LiFePO 4 (LFP) water-based slurries using styrene-butadiene rubber (SBR) as binder and sodium carboxymethyl cellulose (CMC) as thickener, and formulations of different rheological characteristics were investigated. The electrochemical performance (cyclic voltammetry, rate capability) and morphological characteristics of the LFP half-pouch cells (X-ray micro computed tomography and scanning electron microscopy) were compared between the formulations. An optimum electrode formulation was identified, and a mechanism is proposed to explain differences between the formulations. With the optimum electrode formulation, 350 µm casted electrodes with high mechanical stability were achieved. Electrodes exhibited 4–6 times greater areal mass loadings (4–6 mAh cm −2 ) and 50% greater electroactive material weight than with foils. In tests of half- and full-pouch embroidered cells, a 50% capacity utilization at 1C-rate and 11% at 2C-rate were observed, with a full recovery at C/5-rate. The cycling stability was also maintained over 55 cycles.
Gas hydrates are usually synthesized by bringing together a pressurized gas and liquid or solid water. In both cases, the transport of gas or water to the hydrate growth site is hindered once an initial film of hydrate has grown at the water–gas interface. A seemingly forgotten gas-phase technique overcomes this problem by slowly depositing water vapor on a cold surface in the presence of the pressurized guest gas. Despite being used for the synthesis of low-formation-pressure hydrates, it has not yet been tested for hydrates of CO 2 and CH 4 . Moreover, the potential of the technique for the study of hydrate decomposition has not been recognized yet. We employ two advanced implementations of the condensation technique to form hydrates of CO 2 and CH 4 and demonstrate the applicability of the process for the study of hydrate decomposition and the phenomenon of self-preservation. Our results show that CO 2 and CH 4 hydrate samples deposited on graphite at 261–265 K are almost pure hydrates with an ice fraction of less than 8%. Rapid depressurization experiments with thin deposits (approx. 330 mm thickness) of CO 2 hydrate on an aluminum surface at 265 K yield identical dissociation curves when the deposition is done at identical pressure. However, hydrates deposited at 1 MPa almost completely withstand decomposition after rapid depressurization to 0.1 MPa, while samples deposited at 2 MPa decompose 7 times faster. Therefore, this synthesis technique is not only applicable for the study of hydrate decomposition but can also be used for the controlled deposition of a super-preserved hydrate.
Investigation of non-uniformly emitting optical fiber diffusers on the light distribution in tissue
(2020)
The Digital Factory Vorarlberg is the youngest Research Center of Vorarlberg University of Applied Sciences. In the lab of the research center a research and learning factory has been established for educating students and employees of industrial partners. Showcases and best practice scenarios for various topics of digitalization in the manufacturing industry are demonstrated. In addition, novel methods and technologies for digital production, cloud-based manufacturing, data analytics, IT- and OT-security or digital twins are being developed. The factory comprises only a minimum core of logistics and fabrication processes to guarantee manageability within an academic setup. As a product, fidget spinners are being fabricated. A webshop allows customers to individually design their products and directly place orders in the factory. A centralized SCADA-System is the core data hub for the factory. Various data analytic tools and methods and a novel database for IoT-applications are connected to the SCADA-System. As an alternative to on premise manufacturing, orders can be pushed into a cloud-based manufacturing platform, which has been developed at the Digital Factory. A broker system allows fabrication in distributed facilities and offers various optimization services. Concepts, such as outsourcing product configuration to customers or new types of engineering services in cloud-based manufacturing can be explored and demonstrated. In this paper, we present the basic concept of the Digital Factory Vorarlberg, as well as some of the newly developed topics.
Sensemaking
(2020)
Maßnahmen zur Planung, zum Aufbau und zur Steuerung einer Wertschöpfungsarchitektur entfalten ihre Wirkung, wenn sie kontextsensitiv entwickelt und umgesetzt werden. Zu diesem Kontext gehören Strukturen und Prozesse der geplanren Vorgehensweise, ermittelbare Daten und Informationen über das eigene Tun sowie Erwartungen und Verhaltensweisen aller Beteiligten. Im Kern der Bemühungen sollte die Mitgestaltung kommunikativer Prozesse der gemeinsamen Verständigung sein, denn ihre Resonanzen sind die Bezugspunkte für das weitere Tun. Daher gilt: Der betriebswirtschaftliche Erfolg wird maßgeblich geprägt durch die Qualität der Verständigung.
Spielregeln und Spielzüge
(2020)
Die Gültigkeit einer Wirtschaftsordnung (Spielregeln) verlangt den Beteiligten einen allgemeinen Konsens, der sich auch auf die Durchsetzungsinstanzen (Schiedsrichter) bezieht. Es fragt sich, auf welcher Basis dieser Konsens über die Geltung von Spielregeln, Spielzügen und regelkonform sanktionierenden Schiedsrichtern beruht und gibt es dafür benötige Vorbedingungen?
Probemlösung
(2020)
Der Prozess der Problemlösung wird durch aufeinander verweisende, anschlussfähige Kommunikationen zusammengehalten. Mit Kommunikationen wird ein gemeinsames Verständnis über das Gegebene und über das Gewollte erarbeitet (Sensemaking). Das Resultat des Kommunizierens erlangt durch die Abgabe von Selbstverpflichtungen (Commitments) ihre kollektive Verbindlichkeit.
Die Realität ist keinesfalls einfach da. Sie wird vielmehr von den Beteiligten erst kommunikativ erzeugt. Einzeln und gemeinsam werden Beobachtungen und damit erzielte Ergebnisse, gedankliche Vorstellungen, argumentative Begründungen sowie grundlegende Annahmen und damit zusammenhängende Deutungen schriftlich und/oder mündlich kommuniziert und miteinander ausgetauscht.