Refine
Document Type
- Article (9) (remove)
Institute
Language
- English (9) (remove)
Is part of the Bibliography
- no (9) (remove)
Keywords
- 3D MMI splitter (1)
- 3D Y-branch splitter (1)
- Compassionate curriculum (1)
- Discrimination (1)
- Excited States (1)
- Health and social care professionals (1)
- Hot States (1)
- LGBT+ (1)
- Quantum Dots (1)
- Quantum Optics (1)
Modern portable electronic devices have seen component heat load increasing, while the space available for heat dissipation has decreased. This requires the thermal management system to be optimized to attain the high performance heat sink. Heat sinks plays a major role for dissipating heat in electronic devices. Phase change material (PCM) is used to enhance the heat dissipation in heat sink. This paper reports the results of an experimental investigation of the performance of Pin fin heat sinks filled with phase change materials for thermal management of electronic devices. The experimental set ups are prepared with the graphical programming language with Lab VIEW (Laboratory Virtual Instruments for Engineering Workbench. Three different types of Pin fin Heat sink with and without PCM are investigated based on different operational timings and the temperature is acquired with the help of Data Acquisition Card (DAQ). The results indicated that the inclusion of the PCM could stabilize the temperature for a longer period and reduce the heating rates and peak temperatures of heat sink with increasing the number of fins can enhance the thermal performance of electronic devices.
Signatures of the optical stark effect on entangled photon pairs from resonantly-pumped quantum dots
(2023)
Two-photon resonant excitation of the biexciton-exciton cascade in a quantum dot generates highly polarization-entangled photon pairs in a near-deterministic way. However, the ultimate level of achievable entanglement is still debated. Here, we observe the impact of the laser-induced ac-Stark effect on the quantum dot emission spectra and on entanglement. For increasing pulse-duration-to-lifetime ratios and pump powers, decreasing values of concurrence are recorded. Nonetheless, additional contributions are still required to fully account for the observed below-unity concurrence.
The paper deals with designing and numerical modelling a 2 x 2 optical switch for photonic integrated circuits based on 2 x 2 MMI elements and phase modulators. The 2 x 2 optical switch was modelled in the RsoftCAD with the simulation tool BeamPROP. The 2 x 2 optical switch is a common element for creating more complex 1 x N or N x N optical switches in all-optical signal processing.
This paper presents a project developed at the K.S.Rangasamy College of Technology (Tamilnadu,India) aimed at designing, implementing, and testing an autonomous multipurpose vehicle with safe, efficient, and economic operation. This autonomous vehicle moves through the crop lines of a Agricultural land and performs tasks that are tedious and/or hazardous to the farmers. First, it has been equipped for spraying, but other configurations have also been designed, such as: a seeding ,plug platform to reach the top part of the plants to perform different tasks (pruning, harvesting, etc.), and a trailer to transport the fruits, plants, and crop waste.
Synthetic polymers, such as polyamide (PA), inherently possess a moderate number of surface functionalities compared to natural polymers, which negatively impacts the uniformity of metallic coatings obtained through wet-chemical methods like electroless plating. The paper presents the use of a siloxane interlayer formed from the condensation of the hydrolyzed 3-triethoxysilylpropyl succinic anhydride (TESPSA) precursor as a strategy to modify the surface properties of polyamide 6.6 (PA66) fabrics and improve the uniformity of the copper surface coating. The application of the siloxane intermediate coating demonstrates a significant improvement in electrical conductivity, up to 20 times higher than fabrics without the interlayer. The morphology of the coatings was investigated using scanning electron (SEM) and laser confocal scanning microscopy (LSM). In addition, dye adsorption, flexural rigidity, air permeability and contact angle measurements were conducted to monitor the change in the PA66 properties after the siloxane functionalization.
Beyond the Four-Level Model: Dark and Hot States in Quantum Dots Degrade Photonic Entanglement
(2023)
Entangled photon pairs are essential for a multitude of quantum photonic applications. To date, the best performing solid-state quantum emitters of entangled photons are semiconductor quantum dots operated around liquid-helium temperatures. To favor the widespread deployment of these sources, it is important to explore and understand their behavior at temperatures accessible with compact Stirling coolers. Here we study the polarization entanglement among photon pairs from the biexciton–exciton cascade in GaAs quantum dots at temperatures up to ∼65 K. We observe entanglement degradation accompanied by changes in decay dynamics, which we ascribe to thermal population and depopulation of hot and dark states in addition to the four levels relevant for photon pair generation. Detailed calculations considering the presence and characteristics of the additional states and phonon-assisted transitions support the interpretation. We expect these results to guide the optimization of quantum dots as sources of highly entangled photons at elevated temperatures.
In this paper, the design of three-dimensional configuration of Y-branch splitter is compared with Multimode Interference splitter. Both splitters use the IP-Dip polymer as a standard material for 3D laser lithography. The optical properties of the splitters for both approaches are discussed and compared.