Refine
Year of publication
Document Type
- Conference Proceeding (79) (remove)
Institute
Language
- English (79)
Has Fulltext
- no (79) (remove)
Is part of the Bibliography
- yes (79)
Keywords
- arrayed waveguide gratings (9)
- Y-branch splitter (6)
- integrated optics (6)
- photonics (6)
- MMI splitter (5)
- AWG design (4)
- insertion loss (4)
- Arrayed waveguide gratings (3)
- Crosstalk (3)
- MMI splitters (3)
By a simple femtosecond laser process, we fabricated metal-oxide/gold composite films for electrical and optical gas sensors. We designed a dripple wavelength AWG-spectrometer, matched to the plasma absorption wavelength region of the composite films. H2/CO absorptions fit well with the AWG design for multi gas detection sensor arrays
The main aims of this work are the validation of the developed process of gluing a single-mode optical fiber array with a photonic chip and the selection of a more suitable adhesive from the two adhesives being compared. An active alignment system was used for adjusting the two optical fiber arrays to a photonics chip. The gluing was done by two compared UV curable adhesives applied in the optical path. The insertion losses of glued coupling were measured and investigated at two discrete wavelengths 1310 nm and 1550 nm during temperature testing in the climatic chamber according to Telcordia GR_1209_Corei04 [3]. The measurement, investigation, and comparison of insertion losses of the glued coupling at the spectral band from 1530 nm to 1570 nm were done immediately after gluing process and after three temperature cycles in the climatic chamber with one month delay.
In this paper, a 256-channel, 10-GHz arrayed waveguide gratings demultiplexer for ultra-dense wavelength division multiplexing was designed using an in-house developed tool called AWG-Parameters. The AWG demultiplexer was designed for a central wavelength of 1550 nm and the structure was simulated in PHASAR tool from Optiwave. Two different AWG designs were developed and the influence of the design parameters on the AWG performance was studied.
Design, simulation, and optimization of the 1×4 optical three-dimensional multimode interference splitter using IP-Dip polymer as a core and polydimethylsiloxane (PDMS) Sylgard 184 as a cladding is demonstrated. The splitter was simulated by using beam propagation method in BeamPROP simulation module of RSoft photonic tool and optimized for an operating wavelength of 1.55 μm . According to the minimum insertion loss, the dimensions of the splitter were optimized for a waveguide with a core size of 4×4 μm2 . The objective of the study is to create the design for fabrication by three-dimensional direct laser writing optical lithography.
Semiconducting metal oxides are widely used for solar cells, poto-catalysis, bio-active materials and gas sensors. Besides the material properties of the used semiconductor,the specific surface topology of the sensor determines the device performance. We investigate the preparation and transfer suitable metals onto LIPPS structures on glass for gas sensing applications.
The paper shows concepts of optical splitting based on three dimensional (3D) optical splitters based on multimode interference principle. This paper is focused on the design, fabrication and characterization of 3D MMI splitter with formed output waveguides based on IP-Dip polymer for direct application on optical fiber. The MMI optical splitter was simulated and fabricated using direct laser writing process. Output characteristics were characterized by highly resolved near-field scanning optical microscope (NSOM) and compared with 3D MMI splitter without output waveguides.
We present 256-channel, 25-GHz AWG designed for ultra-dense wavelength division multiplexing. For the design two in-house developed tools were used: AWG-Parameters tool for the calculation of input design parameters and AWGAnalyser tool, used to evaluate the simulated transmission characteristics. The AWG structure was designed for AWG central wavelength of 1550 nm and simulated with PHASAR tool from Optiwave. To keep the size of AWG structure as small as possible the number of waveguides in the phased array was tested. The simulations show that there is a certain minimum number of phased array waveguides necessary to reach sufficient AWG performance. After optimization, the AWG structure reached 10 cm x 11 cm in size and satisfying optical properties.
This paper describes two different designs of 1×8 passive optical splitters. The first splitter consists of cascade arranged directional waveguide branches (Y-branch splitter) with (0.8×0.16) µm2 waveguide cross-section. The second splitter is based on multimode interference occurring in a large MMI coupler, which uses a self-imaging effect for beam propagation, exhibiting the same waveguide core size as a Y-branch splitter. The waveguide channel profile, used in both approaches, is based on a silicon nitride material platform, with a refractive index of core being nc = 1.925 and a refractive index of cladding ncl = 1.4575. The splitters are designed as a planar structure for a medical operating wavelength 850 nm. Design, simulation, and optimization of passive optical components are performed by a commercial photonic software tool BeamPROP simulation engine by RSoft Photonics Suite tool, employing beam propagation method. This work aims to find the minimum physical dimensions of the designed splitters with the satisfactory optical performance. According to the minimum insertion loss and minimum non-uniformity, the optimum length of the splitters is determined. Finally, the optical properties of splitters for both approaches are discussed and compared with each other.
Due to the increasing trend of photonic element miniaturisation and the need for optical splitting, we propose and simulate a new type of three-dimensional (3D) optical splitter based on multimode interference (MMI) for the wavelength of 1550 nm. We present various designs and simulations of various parameters for the optimized MMI splitter. We focus on the possibility of its integration on an optical fiber. The design is focused on a possible production process using 3D laser lithography for the prepared experiments. The MMI splitter was prepared by laser lithography using direct writing process and finally investigated by output characterisation by the near-field measurement.
In this paper, we document optical splitters based on Y-branch and also on MMI splitting principle. The 1×4 Y-branch splitter was prepared in 3D geometry fully from polymer approaching the single mode transmission at 1550 nm. We also prepared new concept of 1×4 MMI optical splitter. Their optical properties and character of output optical field were measured by near-field scanning optical microscope. Splitting properties and optical outputs of both splitters are very promising and increase an attractiveness of presented 3D technology and polymers.
The paper deals with the optimization of 2x2 optical switch for photonic integrated circuits based on two 2x2 MMI splitters and two phase-modulators. The optical switch was modelled in the RSoftCAD with the simulation tool BeamPROP. The optimization was done to minimise the insertion losses and broaden the spectral band at 1550 nm by using linear tapers in a 2x2 MMI splitter topology. The 2x2 optical switch is a common element for creating more complex 1xN or NxN optical switches in all-optical signal processing.
Design, simulation, and optimization of the 1×4 optical three-dimensional multimode interference splitter using IP-Dip polymer as a core and polydimethylsiloxane (PDMS) Sylgard 184 as a cladding is demonstrated. The splitter was simulated by using beam propagation method in BeamPROP simulation module of RSoft photonic tool and optimized for an operating wavelength of 1.55 μm . According to the minimum insertion loss, the dimensions of the splitter were optimized for a waveguide with a core size of 4×4 μm2 . The objective of the study is to create the design for fabrication by three-dimensional direct laser writing optical lithography.
In this paper we present various educational activities with Photonics Explorer, an educational kit developed by the photonics research team B - PHOT at VUB (Vrije Universiteit Brussel) for students at secondary schools. The concept is a ‘lab-in-a-box’ that enables students of the 2 nd and 3 rd grade to do photonics experiments themselves at school with lasers, LEDs, lenses, optical fibers, and other high-tech components. Even though, the kit was developed for the secondary schools, we use experiments from the kit also for some other teaching activities such as lectures at the university, photonics workshops for teachers and children at primary/secondary schools or for events such as children's/youth's university or the night of sciences. In the frame of Austrian based project Phorsch! we have organized most of these activities which will be presented here.
A new software tool, called AWG-Channel-Spacing, is developed to calculate accurate channel spacing of an arrayed waveguide gratings (AWG) optical multiplexer/demultiplexer. This tool has been developed with the application framework QT in the programming language C++. The tool was evaluated with a design of 20-channel 200 GHz AWG. The achieved simulated transmission characteristics prove the correct functionality of the tool.
A new software tool, called AWG-Wuckler, is developed to calculate geometric parameters of arrayed waveguide grating structures for telecommunication and medical applications. These parameters are crucial for a AWG layout which will be created and simulated using commercial photonic design tools. The design process of AWG is very complex because its geometric dimensions depend on a large number of input design parameters and other input design parameters. Often geometric constraints require an adjustment of the input design parameters and vice versa. Calculation and adjustment of the geometric parameters is a time-consuming process that is currently not fully supported by any commercial photonic tool. AWG-Wuckler tool overcomes this issue and offers a fast and easy to use solution. The tool was already applied in various AWG designs and is technologically well proven.
In this paper, design of 1×8 multimode interference passive optical splitter is proposed. The structure of the splitter is designed based on a silicon nitride material platform. This work aims to find the minimum physical dimensions of the designed splitters with the satisfactory optical performance. According to the minimum insertion loss and minimum non-uniformity, the optimum length of the splitters is determined.
Femtosecond laser ablation on Si generates 2D ripple structures, known as laser induced periodic surface structures (LIPSS) and pinholes. We fabricated membranes with 20 to 50 μm thickness perforated by an array of tapered pinholes up to 5 μm in diameter and 10 to 20 μm spacing. Within several micrometer the pinholes transform into hollow photonic waveguides with constant diameter from 1μm to 2μm. Such structures offer a 3D photonic coupling device for polymer Y-branch- and MMI-splitter. We measured a considerable change of electrical resistivity for 500 ppm H2 in air using Si/SiO2/TiO2 substrates with 2D LIPSS. We propose to investigate 3D waveguide arrays also for photonic-chemical sensors.
In this paper we report on the experimental test set-up for the temperature characterization of fiber array to photonics chip butt coupling at 1310 nm and 1550 nm wavelengths. The alignment and gluing of fiber arrays to photonics chip were done by automated active alignments system and they were fixed themselves by UV curable epoxy adhesive. Temperature changes of coupling insertion losses are measured and investigated for two different UV adhesives during three temperature cycles from -40 °C to 80 °C in climatic chamber. Spectral dependence of insertion losses was measured and compared before and after three temperature cycles for 1530 nm to 1570 nm spectral range at room temperature.
We present design, simulation and optimization of polymer based 16-channel, 100-GHz AWG designed for central wavelength of 1550 nm. The input design parameters were calculated applying AWG-Parameters tool. The simulations were performed applying a commercial photonic tool PHASAR from Optiwave. The achieved transmission characteristics were evaluated by AWG-Analyzer tool and show a satisfying agreement between designed and simulated AWG optical properties. Finally, the influence of the number of phased array (PA) waveguides on the AWG performance was studied. The results show that there is a certain minimum number of PA waveguides necessary to reach sufficient AWG performance.
This paper presents the design, simulation, and optimization of a 1×128 multimode interference (MMI) splitter with a silica-on-silicon channel profile. This work aims to study the influence of the different S-Bend output waveguide shapes at the end of the MMI coupler on the final optical properties. The 1×128 MMI splitters have been simulated using beam propagation method in OptiBPM software. The optical properties of all considered splitters with different shapes of outputs waveguides are discussed and compared with each other. Based on the minimum insertion loss and non-uniformity, the final shape of output waveguides, ensuring the lowest losses, is determined.
The photonic integrated circuits are required in the next generations of coherent terabit optical communications. The software tools for automated adjustment and coupling of optical fiber arrays to photonic integrated circuits has been developed. The obtained results are needed in final production phase in the technology process of photonic integrated circuits packaging.
We present design and simulation of 16-channel, 100-GHz silicon nitride based AWG using BeamPROP simulation engine of RSoft photonic tool. The AWG was designed for TM-polarized light with central wavelength of 850 nm. The input design parameters were calculated applying AWG-Parameters tool. For this purpose, we created a ridge waveguide structure, used in the design of the AWG layout, and performed FEM simulation. The output of the BPM simulation of AWG structure are the transmission characteristics, which was used to calculate transmission parameters defining optical properties of simulated AWG. The achieved simulation results are in a good agreement with the design.
Comparison of silicon nitride based 8-channel 100-GHz AWGs applying different waveguide structures
(2019)
This paper presents design and simulation of 8-channel, 100-GHz AWGs based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. AWGs were designed for central wavelength of 850 nm applying AWG-Parameters tool. The simulations were performed applying FEM and BPM methods in RSoft and PHASAR photonic tools. The simulation results show considerably lower losses but slightly higher channel crosstalk when applying rib waveguides.
Comparison of silicon nitride based 1x8 Y-branch splitters applying different waveguide structures
(2019)
This paper presents design, simulation and optimization of 1x8 Y-branch power splitters based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. The splitters were designed for 850 nm spectral optical window and the simulations were performed applying FEM and BPM methods in RSoft photonic tool. The aim of this work was to find minimum physical dimensions of the designed splitters occupying minimal space on PIC chip. The optimization was done with regards to high symmetrical splitting ratio and low insertion loss. Finally, the optical properties of both splitters were studied and compared with each other.
Compact and high-resolution 256-channel silicon nitride based AWG-spectrometer for OCT on a chip
(2019)
We present design, simulation and technological verification of a compact 256-channel, 42-GHz silicon nitride based AWG-spectrometer. The spectrometer was designed for TM-polarized light with a central wavelength of 850 nm, applying “AWG-Parameters” tool. This design is based on a previous study of various AWG designs (8-channel, 100-GHz; 20-channel, 50-GHz; 40-channel, 50-GHz, 80-channel, 50-GHz and 160-channel, 50-GHz AWGs), which were all technologically verified. The spectrometer features small size and high resolution. It is integrated on OCT chip using standard CMOS processes. The SD-OCT system is developed to operate in a wavelength range from 800 nm to 900 nm, having 0.1 nm resolution.
Abstract: ams AG is a leading provider of sensing solutions developing semiconductor sensors in a wide variety of fields, with optical sensing as one of the key competences. Since integrated photonics is a promising technology for new sensor systems, ams AG has been developing processes for fully integrated CMOS-compatible photonic components based on Si3N4. This talk will provide an overview on the processing of basic photonic building blocks and their optical properties and performance. We will also give examples for applications in the fields of optical coherence tomography and opto-chemical gas sensing. In the 1980s photonics started its way for common use in telecommunication technology, using optical fiber technologies. In recent years, also a variety of photonic sensors has been proposed and developed. One of the major drawbacks of most of these photonic devices has been the lack of integration into existing (semiconductor) production processes, so far. This integration is feasible using SiN material systems to process monolithically integrated CMOS-compatible photonic sensors in the visible and near-infrared spectrum. We will present the basic processing steps for the SiN photonic technology, the development of some critical processing steps such as SiN deposition and SiN etching as well as several photonic components (waveguides, splitters, etc.) with their optical properties. One of the applications presented relates to optical coherence tomography (OCT), a fast growing imaging technique in ophthalmology. Drawbacks of existing OCT systems are their high costs as well as their bulkiness, which prevents a wider spread use of OCT systems.
One way to overcome both cost and size issues is to integrate optical and electrical components on a single chip.
Part of this work was carried out in the framework of the projects COHESION (funded by the Austrian Research Promotion Agency (FFG), no. 848588), OCTCHIP (funded by the EU’ Horizon 2020 research and innovation programme, no. 688173), and COLODOR (M-ERA.NET transnational Call 2015, funded by the Austrian Research Promotion Agency (FFG), no.854066, and the Bundesministerium für Bildung und Forschung, Germany).
Optical splitters are passive optical components, which have found applications in a wide range of telecom, sensing, medical and many other scientific areas.
Low-index contrast optical splitters (Silica-on-Silicon (SoS) based waveguide devices) feature many advantages such as low fiber coupling losses and low propagation losses. They are considered an attractive DWDM solution in the telecommunication for all optical signal processing in optical communication systems. Nowadays the steadily increasing data volume in communication networks is driven by a rapid proliferation of home-based and business computers, storage capacities, processing capabilities and the extensive availability of Internet. The challenge is to transfer high data volumes in short periods of time over high distances as lossless as possible. The task of the optical splitters in Fiber-to-the-x (FTTx) network is to split one optical signal in many identical signals bringing for example the same TV signal in different households. Of course, the more buildings can be served by one optical splitter the lower are the installation costs.
High-index contrast optical splitters (such as silicon, silicon nitride or polymer based waveguide devices) feature much smaller waveguide size compared to low index contrast splitters. Such compact devices can easily be implemented on-chip and have already been used in the development of optical sensors, devices for DNA diagnostics and for infrared spectroscopy.
We will present the latest achievements in the design of two mostly used optical splitters (MMI and Y-branch) and discuss their advantages and disadvantages. Finally, some applications of the splitters developed in the frame of various projects will be presented.
This work was carried out in the framework of the project PHOCOP (no. SK-AT-2017-0013) and NAMOPRISIN (no. SK-AT-2017-0005) from the Slovak research and development agency of the Ministry of Education, Science, Research and Sport of the Slovak Republic and SK 16/2018 and 15/2018 from OeAD-GmbH.
Progress in integrated photonics enables development of integrated photonics circuits with new unique properties, circuits of the future, and overcomes current limits in information and communication technologies. The packaging of photonic integrated circuits is necessary for taking them out of research laboratories into real implementation in the information and communication technology applications.
Telecom optical fibers are still being the best transmission medium of digital data and analogue signals for long distance applications. The effective coupling of optical radiation between telecom optical fiber with ten microns core dimension and photonic integrated circuits optical waveguides with submicron dimensions are necessary. To address these challenges, we present our concept of photonics integrated circuit packaging with radio frequency, direct current and fiber array ports with automated active alignment system.
SiN is a suitable material for fabricating of photonic integrated circuits with middle refractive index contrast for the visible and near infrared spectral region with ultra-low propagation losses. The paper deals with the design and simulation of fiber to SiN chip butt coupler with single step fabrication process without thickness tapering. Coupler is designed for 850 nm band for coupling between strip 0.25 μm × 1.00 μm waveguide and Nufern's 780-OCT single mode optical fiber with core diameter 4.4 μm. The coupling losses simulation results of the two simulation methods finite-difference beam propagation techniques and eigenmode expansion method are compared.