Refine
Year of publication
Document Type
- Conference Proceeding (20)
- Article (8)
- Part of a Book (1)
Institute
Language
- English (28)
- Multiple languages (1)
Has Fulltext
- no (29)
Keywords
- arrayed waveguide gratings (5)
- photonics (4)
- silicon nitride (4)
- AWG design (2)
- Photonics (2)
- insertion loss (2)
- integrated optics (2)
- integrated photonics (2)
- rib waveguides (2)
- wavelength division multiplexing (2)
Comparison of silicon nitride based 1x8 Y-branch splitters applying different waveguide structures
(2019)
This paper presents design, simulation and optimization of 1x8 Y-branch power splitters based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. The splitters were designed for 850 nm spectral optical window and the simulations were performed applying FEM and BPM methods in RSoft photonic tool. The aim of this work was to find minimum physical dimensions of the designed splitters occupying minimal space on PIC chip. The optimization was done with regards to high symmetrical splitting ratio and low insertion loss. Finally, the optical properties of both splitters were studied and compared with each other.
Comparison of silicon nitride based 8-channel 100-GHz AWGs applying different waveguide structures
(2019)
This paper presents design and simulation of 8-channel, 100-GHz AWGs based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. AWGs were designed for central wavelength of 850 nm applying AWG-Parameters tool. The simulations were performed applying FEM and BPM methods in RSoft and PHASAR photonic tools. The simulation results show considerably lower losses but slightly higher channel crosstalk when applying rib waveguides.
We present design and simulation of 16-channel, 100-GHz silicon nitride based AWG using BeamPROP simulation engine of RSoft photonic tool. The AWG was designed for TM-polarized light with central wavelength of 850 nm. The input design parameters were calculated applying AWG-Parameters tool. For this purpose, we created a ridge waveguide structure, used in the design of the AWG layout, and performed FEM simulation. The output of the BPM simulation of AWG structure are the transmission characteristics, which was used to calculate transmission parameters defining optical properties of simulated AWG. The achieved simulation results are in a good agreement with the design.
The photonic integrated circuits are required in the next generations of coherent terabit optical communications. The software tools for automated adjustment and coupling of optical fiber arrays to photonic integrated circuits has been developed. The obtained results are needed in final production phase in the technology process of photonic integrated circuits packaging.
The main aims of this work are the validation of the developed process of gluing a single-mode optical fiber array with a photonic chip and the selection of a more suitable adhesive from the two adhesives being compared. An active alignment system was used for adjusting the two optical fiber arrays to a photonics chip. The gluing was done by two compared UV curable adhesives applied in the optical path. The insertion losses of glued coupling were measured and investigated at two discrete wavelengths 1310 nm and 1550 nm during temperature testing in the climatic chamber according to Telcordia GR_1209_Corei04 [3]. The measurement, investigation, and comparison of insertion losses of the glued coupling at the spectral band from 1530 nm to 1570 nm were done immediately after gluing process and after three temperature cycles in the climatic chamber with one month delay.
In this paper, a 256-channel, 10-GHz arrayed waveguide gratings demultiplexer for ultra-dense wavelength division multiplexing was designed using an in-house developed tool called AWG-Parameters. The AWG demultiplexer was designed for a central wavelength of 1550 nm and the structure was simulated in PHASAR tool from Optiwave. Two different AWG designs were developed and the influence of the design parameters on the AWG performance was studied.
The paper deals with designing and numerical modelling a 2 x 2 optical switch for photonic integrated circuits based on 2 x 2 MMI elements and phase modulators. The 2 x 2 optical switch was modelled in the RsoftCAD with the simulation tool BeamPROP. The 2 x 2 optical switch is a common element for creating more complex 1 x N or N x N optical switches in all-optical signal processing.