Refine
Document Type
- Conference Proceeding (14)
- Article (8)
Institute
Language
- English (22)
Keywords
- Y-branch splitter (5)
- photonics (4)
- MMI splitter (3)
- MMI splitters (3)
- arrayed waveguide gratings (3)
- 3D MMI splitter (2)
- AWG (2)
- AWG-spectrometer (2)
- Light propagation (2)
- Telecommunications (2)
In this paper, low-loss Y-branch splitters up to 128 splitting ratio are designed, simulated, and optimized by using 2D beam propagation method in OptiBPM tool by Optiwave. For an optical waveguide, a silica-on-silicon material platform is used. The splitters were designed as a planar structure for a telecommunication operating wavelength of 1.55 m. According to the minimum insertion loss and minimum non-uniformity, the optimum length for each Y-branch is determined. The influence of the pre-defined S-Bend waveguide shapes (Arc, Cosine, Sine) and of the waveguide core size reduction on the splitter performance has been also studied. The obtained simulation results of all designed splitters with different S-Bend shape waveguides together with the different waveguide core sizes are discussed and compared with each other.
This paper presents design, simulation, and optimization of the three-dimensional 1×4 optical multimode interference splitter using IP-Dip polymer as a core and polydimethylsiloxane (PDMS) Sylgard 184 as a cladding. The splitter was simulated by using beam propagation method in BeamPROP simulation engine of RSoft photonic tool and optimized for an operating wavelength of 1.55 µm. According to the minimum insertion loss, the dimensions of the MMI coupler and the length of the whole MMI splitter structure were optimized applying a waveguide with a core size of 4×4 µm2. The objective of the study is to create a design for fabrication by three-dimensional direct laser writing optical lithography.
The paper deals with the optimization of 2x2 optical switch for photonic integrated circuits based on two 2x2 MMI splitters and two phase-modulators. The optical switch was modelled in the RSoftCAD with the simulation tool BeamPROP. The optimization was done to minimise the insertion losses and broaden the spectral band at 1550 nm by using linear tapers in a 2x2 MMI splitter topology. The 2x2 optical switch is a common element for creating more complex 1xN or NxN optical switches in all-optical signal processing.
In this work, we investigated the influence of different etch depths of the rib waveguides on the performance of SiN-based AWGs. For this purpose, an 8-channel 100 GHz AWG was designed for a center wavelength of 850 nm. The design parameters entered were calculated using the AWG-Parameters tool. The simulations were performed with a commercial photonic tool PHASAR from Optiwave. The simulated performance was evaluated using the AWG-Analyzer tool. For the AWG design, we used three identical rib waveguides with different etch depths to simulate possible etch imperfection. The simulations show the wavelength shift and degradation of the AWG performance.
This paper presents the design, simulation, and optimization of a 1×128 multimode interference (MMI) splitter with a silica-on-silicon channel profile. This work aims to study the influence of the different S-Bend output waveguide shapes at the end of the MMI coupler on the final optical properties. The 1×128 MMI splitters have been simulated using beam propagation method in OptiBPM software. The optical properties of all considered splitters with different shapes of outputs waveguides are discussed and compared with each other. Based on the minimum insertion loss and non-uniformity, the final shape of output waveguides, ensuring the lowest losses, is determined.
Femtosecond laser ablation on Si generates 2D ripple structures, known as laser induced periodic surface structures (LIPSS) and pinholes. We fabricated membranes with 20 to 50 μm thickness perforated by an array of tapered pinholes up to 5 μm in diameter and 10 to 20 μm spacing. Within several micrometer the pinholes transform into hollow photonic waveguides with constant diameter from 1μm to 2μm. Such structures offer a 3D photonic coupling device for polymer Y-branch- and MMI-splitter. We measured a considerable change of electrical resistivity for 500 ppm H2 in air using Si/SiO2/TiO2 substrates with 2D LIPSS. We propose to investigate 3D waveguide arrays also for photonic-chemical sensors.
We present 256-channel, 25-GHz AWG designed for ultra-dense wavelength division multiplexing. For the design two in-house developed tools were used: AWG-Parameters tool for the calculation of input design parameters and AWGAnalyser tool, used to evaluate the simulated transmission characteristics. The AWG structure was designed for AWG central wavelength of 1550 nm and simulated with PHASAR tool from Optiwave. To keep the size of AWG structure as small as possible the number of waveguides in the phased array was tested. The simulations show that there is a certain minimum number of phased array waveguides necessary to reach sufficient AWG performance. After optimization, the AWG structure reached 10 cm x 11 cm in size and satisfying optical properties.
In this paper, design of 1×8 multimode interference passive optical splitter is proposed. The structure of the splitter is designed based on a silicon nitride material platform. This work aims to find the minimum physical dimensions of the designed splitters with the satisfactory optical performance. According to the minimum insertion loss and minimum non-uniformity, the optimum length of the splitters is determined.
We present design, simulation and optimization of polymer based 16-channel, 100-GHz AWG designed for central wavelength of 1550 nm. The input design parameters were calculated applying AWG-Parameters tool. The simulations were performed applying a commercial photonic tool PHASAR from Optiwave. The achieved transmission characteristics were evaluated by AWG-Analyzer tool and show a satisfying agreement between designed and simulated AWG optical properties. Finally, the influence of the number of phased array (PA) waveguides on the AWG performance was studied. The results show that there is a certain minimum number of PA waveguides necessary to reach sufficient AWG performance.