Refine
Document Type
- Conference Proceeding (14) (remove)
Institute
Language
- English (14)
Has Fulltext
- no (14)
Is part of the Bibliography
- yes (14)
Keywords
- MMI splitter (3)
- MMI splitters (3)
- photonics (3)
- AWG-spectrometer (2)
- Y-branch splitter (2)
- arrayed waveguide gratings (2)
- 1x128 MMI splitter (1)
- 2x2 optical switch (1)
- 3D 1×4 Multimode Interference Splitter (1)
- 3D MMI splitter (1)
Femtosecond laser ablation on Si generates 2D ripple structures, known as laser induced periodic surface structures (LIPSS) and pinholes. We fabricated membranes with 20 to 50 μm thickness perforated by an array of tapered pinholes up to 5 μm in diameter and 10 to 20 μm spacing. Within several micrometer the pinholes transform into hollow photonic waveguides with constant diameter from 1μm to 2μm. Such structures offer a 3D photonic coupling device for polymer Y-branch- and MMI-splitter. We measured a considerable change of electrical resistivity for 500 ppm H2 in air using Si/SiO2/TiO2 substrates with 2D LIPSS. We propose to investigate 3D waveguide arrays also for photonic-chemical sensors.
In this paper, design of 1×8 multimode interference passive optical splitter is proposed. The structure of the splitter is designed based on a silicon nitride material platform. This work aims to find the minimum physical dimensions of the designed splitters with the satisfactory optical performance. According to the minimum insertion loss and minimum non-uniformity, the optimum length of the splitters is determined.
This paper presents the design, simulation, and optimization of a 1×128 multimode interference (MMI) splitter with a silica-on-silicon channel profile. This work aims to study the influence of the different S-Bend output waveguide shapes at the end of the MMI coupler on the final optical properties. The 1×128 MMI splitters have been simulated using beam propagation method in OptiBPM software. The optical properties of all considered splitters with different shapes of outputs waveguides are discussed and compared with each other. Based on the minimum insertion loss and non-uniformity, the final shape of output waveguides, ensuring the lowest losses, is determined.
We present design, simulation and optimization of polymer based 16-channel, 100-GHz AWG designed for central wavelength of 1550 nm. The input design parameters were calculated applying AWG-Parameters tool. The simulations were performed applying a commercial photonic tool PHASAR from Optiwave. The achieved transmission characteristics were evaluated by AWG-Analyzer tool and show a satisfying agreement between designed and simulated AWG optical properties. Finally, the influence of the number of phased array (PA) waveguides on the AWG performance was studied. The results show that there is a certain minimum number of PA waveguides necessary to reach sufficient AWG performance.
By a simple femtosecond laser process, we fabricated metal-oxide/gold composite films for electrical and optical gas sensors. We designed a dripple wavelength AWG-spectrometer, matched to the plasma absorption wavelength region of the composite films. H2/CO absorptions fit well with the AWG design for multi gas detection sensor arrays
Design, simulation, and optimization of the 1×4 optical three-dimensional multimode interference splitter using IP-Dip polymer as a core and polydimethylsiloxane (PDMS) Sylgard 184 as a cladding is demonstrated. The splitter was simulated by using beam propagation method in BeamPROP simulation module of RSoft photonic tool and optimized for an operating wavelength of 1.55 μm . According to the minimum insertion loss, the dimensions of the splitter were optimized for a waveguide with a core size of 4×4 μm2 . The objective of the study is to create the design for fabrication by three-dimensional direct laser writing optical lithography.
In this paper, a 256-channel, 10-GHz arrayed waveguide gratings demultiplexer for ultra-dense wavelength division multiplexing was designed using an in-house developed tool called AWG-Parameters. The AWG demultiplexer was designed for a central wavelength of 1550 nm and the structure was simulated in PHASAR tool from Optiwave. Two different AWG designs were developed and the influence of the design parameters on the AWG performance was studied.