Refine
Year of publication
- 2019 (71) (remove)
Document Type
- Conference Proceeding (42)
- Article (19)
- Part of a Book (4)
- Book (2)
- Doctoral Thesis (1)
- Master's Thesis (1)
- Periodical (1)
- Part of Periodical (1)
Institute
- Forschungszentrum Mikrotechnik (28)
- Forschungszentrum Business Informatics (15)
- Soziales & Gesundheit (7)
- Technik | Engineering & Technology (7)
- Department of Computer Science (Ende 2021 aufgelöst; Integration in die übergeordnete OE Technik) (6)
- Didaktik (mit 31.03.2021 aufgelöst; Integration ins TELL Center) (5)
- Forschungszentrum Energie (5)
- Forschungszentrum Human Centred Technologies (5)
- Wirtschaft (5)
- Forschungszentrum Digital Factory Vorarlberg (2)
Language
- English (71) (remove)
Keywords
- Constrained Optimization (3)
- silicon nitride (3)
- Evolution Strategies (2)
- Theoretical Analysis (2)
- conically constrained problem (2)
- constrained optimization (2)
- integrated photonics (2)
- repair by projection (2)
- AAL (1)
- AWG design (1)
SiN is a suitable material for fabricating of photonic integrated circuits with middle refractive index contrast for the visible and near infrared spectral region with ultra-low propagation losses. The paper deals with the design and simulation of fiber to SiN chip butt coupler with single step fabrication process without thickness tapering. Coupler is designed for 850 nm band for coupling between strip 0.25 μm × 1.00 μm waveguide and Nufern's 780-OCT single mode optical fiber with core diameter 4.4 μm. The coupling losses simulation results of the two simulation methods finite-difference beam propagation techniques and eigenmode expansion method are compared.
In this thesis the effect of dc voltage bias on the equivalent series resistance (ESR) of capacitors and especially ferroelectric dielectric ceramic capacitors (FDCC) is analysed. Further the influence of the dc biased ESR on the losses of capacitors is investigated. Also piezoelectric resonances (PR) occurring in FDCCs with applied dc bias and their influence on the losses are analysed.
Therefore a measurement circuit to measure the impedance and thus the ESR of capacitors in combination with a vector network analyser (VNA) is developed. Using the developed circuit the ESR of capacitors of different technologies is measured and their behaviour with dc bias is evaluated. The losses of an FDCC are measured in a power electronic (PE) circuit with a developed calorimetric measurement system (CMS). The influence of the PR is investigated by tuning the switching frequency of the PE system and thus the frequency of the capacitor current exactly into the PR. The measured losses are then compared to a calculation based on the capacitor current harmonics and the respective ESR.
The measurements show an increase of the ESR with dc bias for all measured FDCCs. The loss measurements show a significant increase of the losses in an FDCC if the current frequency matches the PR frequency. Consequently a decrease of the PE system's efficiency is measured. The loss calculations do not exactly match the measurements but there is a systematic deviation of the same order for all measurements.
In this study, we carried out the structural and thermal characterization of a medical-grade poly (lactide) (PLA) by SEC, TGA, DSC, NMR, ICP-MS and Py-GC/MS. Moreover, we investigated the laser-induced degradation occurring when ultrashort laser pulses (ULP) were employed to cut extremely thin polymer films prepared by solvent-casting. ULP polymer cutting technology is an interesting manufacturing process for its advantages in potential medical applications. In fact, heat transmission to the region surrounding the cuts is limited, so that the incisions are precise and the effects on the regions around them are small. In this way, the need for post-processing is reduced and ULP cutting becomes interesting for industrial applications. However, degradation induced by ULP may occur and compromise the properties of the polymer samples. To investigate this possibility, portions of PLA films, ultrashort laser cut (ULC) and uncut, were analysed by SEC, DSC, NMR and FTIR. Furthermore, PLA oligomers were studied by ESI-MS. Both SEC and NMR showed a decrease in the molecular weight. FTIR, ESI-MS and NMR spectra revealed the presence of olefin end groups originated from a \beta-H transfer mechanism, induced by heat and/or light (Norrish II mechanism). Additionally, the inspection of the ESI mass spectra highlighted the cleavage of ester bonds related to the Norrish I type mechanism, undetected by the other techniques.