Refine
Year of publication
Document Type
- Conference Proceeding (20) (remove)
Institute
Language
- English (20)
Has Fulltext
- no (20)
Is part of the Bibliography
- yes (20)
Keywords
- arrayed waveguide gratings (3)
- photonics (3)
- silicon nitride (3)
- AWG design (2)
- integrated optics (2)
- integrated photonics (2)
- 2x2 optical switch (1)
- AWG-Analyzer tool (1)
- AWG-based demultiplexers (1)
- AWG-parameter layout (1)
The main aims of this work are the validation of the developed process of gluing a single-mode optical fiber array with a photonic chip and the selection of a more suitable adhesive from the two adhesives being compared. An active alignment system was used for adjusting the two optical fiber arrays to a photonics chip. The gluing was done by two compared UV curable adhesives applied in the optical path. The insertion losses of glued coupling were measured and investigated at two discrete wavelengths 1310 nm and 1550 nm during temperature testing in the climatic chamber according to Telcordia GR_1209_Corei04 [3]. The measurement, investigation, and comparison of insertion losses of the glued coupling at the spectral band from 1530 nm to 1570 nm were done immediately after gluing process and after three temperature cycles in the climatic chamber with one month delay.
In this paper, a 256-channel, 10-GHz arrayed waveguide gratings demultiplexer for ultra-dense wavelength division multiplexing was designed using an in-house developed tool called AWG-Parameters. The AWG demultiplexer was designed for a central wavelength of 1550 nm and the structure was simulated in PHASAR tool from Optiwave. Two different AWG designs were developed and the influence of the design parameters on the AWG performance was studied.
The paper deals with the optimization of 2x2 optical switch for photonic integrated circuits based on two 2x2 MMI splitters and two phase-modulators. The optical switch was modelled in the RSoftCAD with the simulation tool BeamPROP. The optimization was done to minimise the insertion losses and broaden the spectral band at 1550 nm by using linear tapers in a 2x2 MMI splitter topology. The 2x2 optical switch is a common element for creating more complex 1xN or NxN optical switches in all-optical signal processing.
This paper describes two different designs of 1×8 passive optical splitters. The first splitter consists of cascade arranged directional waveguide branches (Y-branch splitter) with (0.8×0.16) µm2 waveguide cross-section. The second splitter is based on multimode interference occurring in a large MMI coupler, which uses a self-imaging effect for beam propagation, exhibiting the same waveguide core size as a Y-branch splitter. The waveguide channel profile, used in both approaches, is based on a silicon nitride material platform, with a refractive index of core being nc = 1.925 and a refractive index of cladding ncl = 1.4575. The splitters are designed as a planar structure for a medical operating wavelength 850 nm. Design, simulation, and optimization of passive optical components are performed by a commercial photonic software tool BeamPROP simulation engine by RSoft Photonics Suite tool, employing beam propagation method. This work aims to find the minimum physical dimensions of the designed splitters with the satisfactory optical performance. According to the minimum insertion loss and minimum non-uniformity, the optimum length of the splitters is determined. Finally, the optical properties of splitters for both approaches are discussed and compared with each other.
In this paper we report on the experimental test set-up for the temperature characterization of fiber array to photonics chip butt coupling at 1310 nm and 1550 nm wavelengths. The alignment and gluing of fiber arrays to photonics chip were done by automated active alignments system and they were fixed themselves by UV curable epoxy adhesive. Temperature changes of coupling insertion losses are measured and investigated for two different UV adhesives during three temperature cycles from -40 °C to 80 °C in climatic chamber. Spectral dependence of insertion losses was measured and compared before and after three temperature cycles for 1530 nm to 1570 nm spectral range at room temperature.
Comparison of silicon nitride based 1x8 Y-branch splitters applying different waveguide structures
(2019)
This paper presents design, simulation and optimization of 1x8 Y-branch power splitters based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. The splitters were designed for 850 nm spectral optical window and the simulations were performed applying FEM and BPM methods in RSoft photonic tool. The aim of this work was to find minimum physical dimensions of the designed splitters occupying minimal space on PIC chip. The optimization was done with regards to high symmetrical splitting ratio and low insertion loss. Finally, the optical properties of both splitters were studied and compared with each other.
Comparison of silicon nitride based 8-channel 100-GHz AWGs applying different waveguide structures
(2019)
This paper presents design and simulation of 8-channel, 100-GHz AWGs based on Si/SiO2/SiN/SiOx material platform. For the designs, two different waveguide structures were used, i.e. ridge and rib waveguides. AWGs were designed for central wavelength of 850 nm applying AWG-Parameters tool. The simulations were performed applying FEM and BPM methods in RSoft and PHASAR photonic tools. The simulation results show considerably lower losses but slightly higher channel crosstalk when applying rib waveguides.
We present design and simulation of 16-channel, 100-GHz silicon nitride based AWG using BeamPROP simulation engine of RSoft photonic tool. The AWG was designed for TM-polarized light with central wavelength of 850 nm. The input design parameters were calculated applying AWG-Parameters tool. For this purpose, we created a ridge waveguide structure, used in the design of the AWG layout, and performed FEM simulation. The output of the BPM simulation of AWG structure are the transmission characteristics, which was used to calculate transmission parameters defining optical properties of simulated AWG. The achieved simulation results are in a good agreement with the design.
The photonic integrated circuits are required in the next generations of coherent terabit optical communications. The software tools for automated adjustment and coupling of optical fiber arrays to photonic integrated circuits has been developed. The obtained results are needed in final production phase in the technology process of photonic integrated circuits packaging.
Progress in integrated photonics enables development of integrated photonics circuits with new unique properties, circuits of the future, and overcomes current limits in information and communication technologies. The packaging of photonic integrated circuits is necessary for taking them out of research laboratories into real implementation in the information and communication technology applications.
Telecom optical fibers are still being the best transmission medium of digital data and analogue signals for long distance applications. The effective coupling of optical radiation between telecom optical fiber with ten microns core dimension and photonic integrated circuits optical waveguides with submicron dimensions are necessary. To address these challenges, we present our concept of photonics integrated circuit packaging with radio frequency, direct current and fiber array ports with automated active alignment system.
SiN is a suitable material for fabricating of photonic integrated circuits with middle refractive index contrast for the visible and near infrared spectral region with ultra-low propagation losses. The paper deals with the design and simulation of fiber to SiN chip butt coupler with single step fabrication process without thickness tapering. Coupler is designed for 850 nm band for coupling between strip 0.25 μm × 1.00 μm waveguide and Nufern's 780-OCT single mode optical fiber with core diameter 4.4 μm. The coupling losses simulation results of the two simulation methods finite-difference beam propagation techniques and eigenmode expansion method are compared.
Design of low loss 1x64 y-branch splitter having symmetric splitting ratio and small footprint
(2014)
Silicon nanophotonics
(2013)